Interface ICs
ژێرپۆلەکان
بەرهەمەکان (5,100+)
DG406DJZ - 16:1 CMOS Analog Multiplexer | Renesas
The Renesas Electronics DG406DJZ is a single 16:1 CMOS analog multiplexer with 100 ohm on-state resistance, housed in a 28-pin PDIP package. It combines a 16-channel analog switch array with TTL- and CMOS-compatible channel decoding, an enable input for device selection, and an internal voltage reference for logic thresholds. These characteristics make the DG406DJZ suitable for routing one analog signal source among as many as 16 external inputs. A CMOS analog multiplexer is an interface IC that connects multiple signal paths to one shared internal node. Its position in the hierarchy is analog switch -> multiplexer -> interface IC -> semiconductor. Unlike a mechanical switch, the DG406DJZ changes channels electronically according to binary select inputs, allowing a microcontroller or other digital controller to scan sensors, measurements, or communication lines efficiently. The DG406DJZ uses four binary select inputs to address 16 channels. Its enable function allows the selected device to be disabled while other multiplexers share the same system bus, which is useful in larger routing or measurement systems. The 100 ohm maximum on-state resistance and TTL/CMOS-compatible decoding simplify interface design in both legacy and modern control systems. The monolithic CMOS implementation integrates 16 analog switches, address decoding, logic-threshold referencing, and enable control. According to the Renesas DG406 and DG407 datasheet, this device family was designed as a drop-in replacement for the popular DG506A and DG507A series. That heritage supports board-level modernization when existing multiplexer footprints must be retained. Typical applications include data-acquisition systems, audio signal routing, test equipment, communication systems, sample-and-hold circuits, and guidance or control systems. The enable input is particularly useful when several multiplexers share a common output or when a system requires deliberate isolation of an inactive routing node. When laying out a PCB, place the selected signal source and destination traces away from digital address and enable lines, and terminate unused channels according to the manufacturer's application guidance. Check the absolute maximum ratings, supply-voltage limits, and switch-state behavior in the datasheet before applying signals or changing the logic reference configuration. This product page combines the manufacturer family documentation, verified distributor packaging information, a focused comparison of genuine 28-pin alternatives, and practical integration guidance for engineers evaluating the DG406DJZ as a retrofit or new-design multiplexer.
DG406DN+ - 16:1 CMOS Analog Multiplexer | Vishay
Vishay Intertechnology DG406DN+ is a 16-channel, single-ended CMOS analog multiplexer that routes one of 16 inputs to a common output according to a 4-bit binary address. It offers a typical on-resistance of 50 ohm, low charge injection of 15 pC, a fast transition time of 200 ns, low power consumption of 0.2 mW, and a maximum supply rating of 44 V. The device is supplied in a 28-pin PLCC package measuring 11.51 mm by 11.51 mm. An analog multiplexer is an interface IC that selects one signal path from multiple analog inputs and connects it to a shared output. This reduces the number of input channels required by a data-acquisition, test, measurement, control, or communication system. The DG406DN+ belongs to the CMOS analog-switch and multiplexer hierarchy, where low on-resistance, controlled charge injection, and predictable transition behavior help preserve signal fidelity. Key features include a guaranteed maximum on-resistance of 100 ohm and operation in either signal direction. Improved versions also provide guaranteed channel matching of no more than 8 ohm and flatness of no more than 9 ohm over the specified signal range. The 4-bit address interface supports 16 channel selections, while the single-supply capability simplifies power architecture in systems that do not require dual-rail operation. The DG406DN+ uses CMOS construction to provide low power use while maintaining short switching transitions. Its 15 pC charge-injection figure reduces the transient error produced when the address changes. Low on-resistance is particularly useful when routing higher-impedance sensors or low-amplitude signals because it minimizes voltage loss and improves input impedance. The 200 ns transition time supports faster measurement sequences than a slower mechanical or relay-based selector. Typical uses include multiplexed sensor acquisition, automated test equipment, data acquisition, industrial control, signal routing, and communication systems. In each case, the DG406DN+ can consolidate multiple analog inputs onto a shared amplifier, converter, or processing channel. Designers must still evaluate signal amplitude, bandwidth, injected charge, and channel settling time for their specific source impedance and acquisition speed. The primary design consideration is ensuring that the selected source impedance, acceptable settling interval, and allowable charge-injection error match the application. A low source resistance reduces settling error, while high source impedance can increase sensitivity to switch resistance and capacitance. Decoupling, grounding, and address-transition timing should be handled according to the manufacturer recommendations. This page consolidates verified manufacturer and distributor information, package characteristics, pricing, drop-in candidates, and practical application guidance. It also distinguishes documented electrical facts from values that require confirmation, providing a practical engineering starting point without treating undocumented specifications as guaranteed.
DG406DN+T - 16:1 CMOS Analog Multiplexer | Analog Devices
The Analog Devices DG406DN+T is a 16-channel, single-ended CMOS analog multiplexer with a maximum on-resistance of 100 Ω, housed in a 28-pin PLCC package measuring 11.51 mm by 11.51 mm. It connects one of 16 input channels to a common output according to a 4-bit binary address. The DG406 family is designed for selecting signals in data-acquisition, instrumentation, communication, test, and measurement systems where multiple analog sources must share a limited number of converter or processing inputs. An analog multiplexer is an analog switch that routes a selected input to a shared output while blocking the unselected channels. In the device hierarchy, the DG406DN+T is an analog multiplexer, a type of analog switch and interface IC. The DG406 family provides 16 single-ended channels, while the related DG407 family provides eight differential channels. This distinction matters because single-ended routing is suitable for unipolar or common-referenced signals, whereas differential multiplexing is preferred for noise-sensitive differential sources. The manufacturer identifies the DG406 as an improved CMOS analog multiplexer with production status. Its maximum on-resistance is 100 Ω, and the manufacturer also lists guaranteed channel matching of 8 Ω maximum and flatness of 9 Ω maximum over the specified signal range. These specifications support low channel-to-channel variation when a system must measure different analog sources through a common front end. The 4-bit address interface reduces the control logic required to identify the active input. The DG406 architecture uses CMOS switching elements to provide low power consumption, high switching speed, and consistent signal behavior. Exact switching time, charge injection, off-state leakage, supply current, logic levels, and allowable input-voltage limits are not published in the retrieved product summaries and should be confirmed in the manufacturer datasheet before timing- or precision-sensitive design. Because on-resistance contributes directly to the source impedance seen by downstream converters, system gain and settling calculations should include the selected switch path. Typical uses include multiplexed data acquisition, automated test equipment, sensor-interface boards, sample-and-hold systems, industrial control modules, and laboratory instruments. The common output can feed an ADC, instrumentation amplifier, measurement front end, or another signal-processing stage. The common-output architecture reduces the number of expensive converter channels, although it also introduces mux on-resistance and switching transients that the downstream acquisition chain must tolerate. PCB design should keep input and output routing compact, provide a continuous ground reference, and place bypass capacitance near the power pins. Address and enable traces should be controlled away from sensitive analog inputs to minimize capacitive coupling. Because the PLCC footprint is not represented in the available package-diagram library, verify the physical pin orientation and numbering directly against the manufacturer datasheet and the PCB footprint before assembly. This product page combines the manufacturer’s DG406 architecture information with distributor package and ordering data, a parameter-by-parameter replacement comparison, and practical guidance for layout, signal integrity, and component selection. It is intended to help engineers confirm fit, evaluate channel-error budgets, and choose a pin-compatible replacement without changing the existing 28-pin PLCC layout.
DG406DW - 16-Channel CMOS Analog Multiplexer | Vishay
The Vishay Intertechnology DG406DW is a 16-channel, single-ended CMOS analog multiplexer that routes one of 16 inputs to a common output using a 4-bit binary address. It provides a maximum on-resistance of 100 ohm, 15 pC charge injection, a 200 ns transition time, low power dissipation of 0.2 mW, and single-supply operation with a 44 V maximum supply rating. The device is packaged in a 28-SOIC package. An analog multiplexer is a semiconductor switch that connects multiple analog signal sources to one shared processing channel. It belongs to the interface IC hierarchy and reduces the number of input pins required by measurement, test, and routing systems. The DG406 is designed for single-ended routing, while companion devices in the DG406/DG407 family address differential multiplexing requirements. Key features include break-before-make switching, which prevents two sources from momentarily being connected together during channel changes. The maximum on-resistance of 100 ohm helps limit signal attenuation in high-impedance measurement circuits. Low charge injection of 15 pC reduces the voltage disturbance generated when the address changes, and the 200 ns transition time supports relatively fast data acquisition. Internally, the DG406 uses CMOS switching elements controlled by four address inputs and an inhibit function. Address decoding determines which of the 16 source channels connects to the common drain. Break-before-make operation protects sensitive measurement front ends from accidental source-to-source shorts, while the low 0.2 mW power dissipation suits remote and battery-operated instrumentation. Typical uses include high-speed data acquisition, audio signal switching and routing, automated test equipment, avionics systems, and remote instrumentation. The device can also serve in instrumentation systems that scan multiple sensor outputs, provided the source impedance, acquisition time, charge injection, and supply voltage are evaluated together. When laying out a DG406DW circuit, place the common output and selected input traces away from digital address lines, provide a solid ground reference, and use the pin-description table in the manufacturer datasheet when assigning PCB tracks. Check off-state leakage and switch capacitance before designing a high-impedance front end. This page combines the manufacturer datasheet characteristics, package information, application guidance, comparison parameters, and practical design notes to support component selection, PCB implementation, and sourcing decisions for the DG406DW.
DG406DY - 16-Channel CMOS Analog Multiplexer | Renesas
The Renesas Electronics DG406DY is a monolithic CMOS analog multiplexer that routes one of sixteen analog inputs to a single output, or eight inputs differentially, in a 28-pin SOIC (SOIC-28) surface-mount package. It supports analog supplies of up to ±20 V (34 V total across both rails), presents a 100 ohm on-resistance per channel, and combines an array of sixteen analog switches with a TTL- and CMOS-compatible digital decode circuit, an internal voltage reference for logic thresholds, and an ENABLE input for cascading several multiplexers on the same bus. A CMOS analog multiplexer is a switching matrix that connects one of many source terminals to a common terminal under digital control. In the broader taxonomy it sits between the analog switch and the interface IC, feeding the signal path of test equipment, data acquisition systems, and audio routing gear. The DG406 series was designed as a pin-compatible plug-in upgrade for the industry-standard DG406/DG407 family and as a drop-in replacement for the popular DG506A and DG507A series devices. Key features include sixteen analog switches in a 1 x 16:1 single-ended configuration or 8 x 1:1 differential configuration, binary address inputs for channel selection, a separate ENABLE pin for device-level gating, and an internal logic-threshold reference that lets TTL and CMOS logic drive the decode circuit directly from a single supply rail. The part is offered in a plastic SOIC-28 surface-mount package and is listed as an industrial-temperature-grade component. Internally, the DG406 uses CMOS transmission gates, so the channel impedance stays nearly flat and the leakage is low compared with older junction-type analog switches. The device also provides break-before-make behaviour on channel change, which matters when the mux sits in front of a sample-and-hold stage where charge injection from a half-transitioned switch would corrupt the sample. Typical uses include audio signal routing in mixing consoles, multiplexed data acquisition front ends, guidance and control systems, sample-and-hold circuits, and general-purpose test equipment where many sensors or sources must share a single instrumentation amplifier channel. A practical design consideration is supply decoupling: place a local bypass capacitor at each analog supply pin and keep the analog routing traces short and shielded from the digital address lines, because the address decode transitions can couple into the selected channel when the source impedance is high. This page consolidates the manufacturer datasheet detail, package and ordering information, pin-compatible and drop-in replacement options, and practical layout guidance for engineers who need more than a bare parameter table when placing the DG406DY on a new board.
DG406DYZ - 16:1 CMOS Analog Multiplexer | Renesas
The Renesas Electronics DG406DYZ is a single 16:1 CMOS analog multiplexer with a 100 ohm on-resistance, housed in a 28-pin SOIC package. It provides sixteen analog switches, TTL- and CMOS-compatible channel decoding, an internal voltage reference for logic thresholds, and an ENABLE input for multiplexing multiple devices. The same architecture can be configured for single-ended 16-channel routing or differential 8-channel routing. An analog multiplexer is a semiconductor switching network that connects one of several input terminals to a common output. It belongs to the analog switch and multiplexer hierarchy within interface ICs. By translating binary address and enable signals into controlled switch states, a multiplexer's digital control logic can route low-frequency analog signals without requiring a separate analog switch for every connection. The DG406 family combines a 16-switch array with address-decoding circuitry in one monolithic CMOS device. Its TTL- and CMOS-compatible control inputs simplify interfacing with modern digital systems, while the voltage reference establishes consistent switching thresholds. The ENABLE input allows multiple multiplexers to share address lines and prevents unwanted paths from being connected when the device is disabled. Renesas describes the DG406 and DG407 as drop-in replacements for the DG506A and DG507A series. That legacy continuity makes the DG406 useful in equipment designed around established 28-pin analog-routing interfaces. The principal design consideration is ensuring that signal amplitude, bandwidth, leakage, charge injection, and switching transients remain acceptable for the source and destination circuitry. Typical applications include audio signal routing, communication systems, data-acquisition systems, guidance and control systems, sample-and-hold circuits, and test equipment. In a data-acquisition system, the device can route multiple sensor or measurement channels into a shared converter input. In audio equipment, it can select among several signal paths while preserving a common downstream amplifier or converter. For PCB design, place the device so every selected analog trace remains short and away from high-speed digital and switching-power paths. Confirm input and output voltage limits, supply requirements, and the control-logic truth table in the manufacturer datasheet. Verify the supported switch configuration and signal polarity before finalizing differential routing. This page organizes the DG406DYZ architecture, verified technical characteristics, same-footprint alternatives, and application-focused design guidance into a concise engineering reference for analog-routing designs.
DG407CJ+ - Dual 8:1 CMOS Analog Multiplexer, 100 Ohm | ADI
The Analog Devices (Maxim Integrated) DG407CJ+ is an improved dual 8-channel (differential 8:1) CMOS analog multiplexer delivering a maximum on-resistance of 100 ohm in a 28-pin PDIP (DIP-28) package. It integrates two independent 8:1 switch circuits for true differential signal switching in a single device. An analog multiplexer is a type of analog switch IC that selects one of several input signals and routes it to a single output under digital control. In the broader signal-chain hierarchy, the multiplexer sits between sensors or signal sources and amplifiers or ADCs, functioning as the routing element of data acquisition and instrumentation systems. The DG407 belongs to the CMOS analog multiplexer switch IC family alongside related devices such as the DG406 (16:1 single-ended version). Key features include guaranteed channel-to-channel on-resistance matching of 8 ohm max, on-resistance flatness of 9 ohm max over the specified signal range, and bidirectional signal conduction - the switches conduct equally well in either direction. The redesigned DG406/DG407 family from Maxim (now Analog Devices) improved matching and flatness over earlier CMOS multiplexer generations, which directly reduces signal-path distortion and channel-to-channel gain error in precision systems. Technically, the DG407 uses CMOS transmission-gate switch elements driven by internal TTL/CMOS-compatible logic decoding, allowing either supply configuration commonly used in industrial analog front ends. Break-before-make switching prevents momentary shorting of two selected channels during address transitions, an important behavior for measurement integrity. Typical applications include differential data acquisition systems, precision test and measurement instrumentation, industrial process-control front ends, and audio or telemetry signal routing where a low 100 ohm max on-resistance preserves signal amplitude with typical load impedances. A key design consideration: on-resistance of 100 ohm forms a divider with the load impedance, so keep load resistance at least 100x higher (10 megaohm or appropriate buffering) to limit gain error, and verify logic-level compatibility with your controller supply rails. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
DG407DJ+ - Dual 8:1 CMOS Analog Multiplexer | Analog Devices
Analog Devices DG407DJ+ is a dual 8:1 CMOS analog multiplexer with 100 ohm maximum on-resistance, 15 pC maximum charge injection, 8 ohm maximum channel matching, and 9 ohm maximum flatness, housed in a 28-pin PDIP package. The device combines two independently selectable 8-to-1 analog switches with TTL- and CMOS-compatible decoding, a logic-threshold voltage reference, and an enable input for cascading multiple multiplexers. An analog multiplexer is a switching interface that connects one source path to one of several signal paths. The DG407 belongs to the broader analog switch and multiplexer hierarchy, where it enables one physical signal to be routed among multiple sensors, test points, amplifiers, or data-conversion channels. Its differential 8-channel configuration makes it useful when the switched signal must be balanced or when two related signals are selected together. Key features include a maximum on-resistance of 100 ohm, guaranteed channel matching of 8 ohm maximum, and signal-range flatness of 9 ohm maximum. Charge injection is limited to 15 pC maximum, reducing the switching transient that can otherwise disturb precision measurement nodes. The on-resistance conducts equally well in either direction, while TTL- and CMOS-compatible address inputs simplify control from digital logic. Internally, the DG407 uses an array of 16 analog switches and a digital decode circuit for channel selection. A voltage reference establishes the logic thresholds, and the enable input permits device selection when more than one multiplexer is installed. These functions allow engineers to construct larger switched-channel systems while retaining standardized digital control. Typical applications include battery-cell measurement, automated test equipment, data acquisition, industrial process monitoring, instrumentation, and multiplexed sensor interfaces. The device is particularly appropriate when a low-frequency analog node must be routed among several inputs with controlled resistance, matching, and charge injection. Designers should account for the 100 ohm maximum on-resistance when calculating source impedance and settling behavior. Input and ground routing should minimize parasitic resistance and coupling, while digital address and enable traces should be kept away from sensitive analog conductors. The 28-pin PDIP package also requires adequate through-hole spacing and suitable protection from mechanical or moisture exposure. This product page combines the verified manufacturer and distributor information with package-specific selection guidance, data gaps, pricing context, and same-footprint alternatives. It distinguishes directly documented variants from candidates that require independent pin, logic-level, and absolute-maximum-rating verification before substitution.
DG407DN+ - Dual 8:1 CMOS Analog Multiplexer | Analog Devices
The Analog Devices DG407DN+ is an improved dual 8-channel CMOS analog multiplexer with a maximum on-state resistance of 100 ohm, packaged in a 28-pin PLCC. It combines two independently addressed 8:1 muxes with TTL- and CMOS-compatible channel-selection logic, allowing sixteen analog inputs to share two common outputs. The device supports communication systems, audio signal routing, data acquisition, guidance and control systems, sample-and-hold circuits, and test equipment. An analog multiplexer is a semiconductor switching network that routes one of several analog inputs to a shared output according to binary address and enable signals. In the signal-chain hierarchy, the DG407DN+ is a CMOS analog switch IC, a precision signal-routing component, and part of a broader data-acquisition or communication system. The 28-pin PLCC provides a standardized leaded surface-mount footprint suitable for compact industrial, instrumentation, and embedded-control equipment. The manufacturer describes DG407 as an improved 16-channel or dual 8-channel CMOS analog multiplexer family. Verified distributor information identifies DG407DN+ as a two-circuit 8:1 switch with 100-ohm maximum on-state resistance in a 28-pin PLCC measuring 11.51 mm by 11.51 mm. Its TTL- and CMOS-compatible digital decode circuitry allows the address and enable inputs to operate with common logic families, while the enable function can deselect the mux when it is not required. The DG407 family includes sixteen analog switches, a binary channel-selection decoder, a voltage reference for logic thresholds, and an enable input for device selection. This integrated addressing arrangement reduces the number of external control components required in multiplexed analog systems. The Analog Devices product page also identifies the DG406 and DG407 devices as pin-compatible plug-in upgrades for the industry-standard DG506A and DG507A families, supporting design migration without changing the board footprint. Typical uses include selecting among multiple sensors in a data-acquisition system, routing audio signals between functional blocks, multiplexing instrumentation channels, and directing control signals in communication equipment. Because the mux contains two 8:1 sections, adjacent channel pairs can also be combined as differential or paired selections where the system architecture requires it. The principal design trade-off is the 100-ohm maximum on-state resistance, which can introduce signal attenuation and distortion compared with lower-resistance switching networks. PCB designers should keep analog traces short and provide a stable ground reference beneath the PLCC while separating sensitive inputs from switching or digital return currents. Power and ground connections should be decoupled close to the device, and unused digital inputs should be driven to a defined logic level rather than left floating. The manufacturer datasheet should be consulted for the exact pin assignments, truth table, control timing, electrical limits, and recommended operating conditions before layout or firmware is released. This product record combines verified manufacturer and distributor information, package and pricing references, pin-compatible alternatives, application guidance, and practical selection considerations. It is intended to support sourcing and engineering evaluation while preserving explicit markers wherever the supplied source material does not expose a verified parameter.
DG407DN+T Dual 8:1 CMOS Analog Mux | Analog Devices
The Analog Devices DG407DN+T is an improved 16-channel, dual 8:1 CMOS analog multiplexer with a maximum on-state resistance of 100 ohms, 200 ns switch-on time, and a 28-pin PLCC package measuring 11.51 mm by 11.51 mm. It supports analog signal routing, data acquisition, communication systems, guidance and control systems, sample-and-hold circuits, and test equipment. The device is designed for TTL- and CMOS-compatible address and enable control, making it suitable for multiplexed measurement and signal-selection systems. An analog multiplexer is an integrated switching circuit that connects one of several analog inputs to a shared output according to digital address logic. The dual 8:1 architecture provides two independent 8:1 multiplexer sections, while the differential configuration can support sixteen single-ended channels or eight differential channels. This places the DG407DN+T within the hierarchy of analog switch IC, multiplexer, interface IC, and semiconductor. Key characteristics include a maximum on-resistance of 100 ohms, a switch-on time of 200 ns, and an operating temperature range from -40 °C to +85 °C. Its CMOS implementation supports low-power mixed-signal systems, while the separate enable input allows a selected multiplexer section to participate in broader system control. The 28-PLCC package is intended for surface-mount assembly and provides a defined footprint for PCB layouts based on the device pinout. The DG407 family is described by Analog Devices as an improved alternative to industry-standard DG406 and DG407 devices. Its address decoder accepts digital control signals, selects the requested analog path, and connects that path to the common output. Because switch resistance and transition time influence insertion loss and settling behavior, the 100-ohm resistance and 200 ns turn-on specification are important when designing acquisition chains or instrumentation with limited timing margin. The manufacturer identifies audio signal routing, communication systems, data-acquisition systems, guidance and control systems, sample-and-hold circuits, and test equipment as suitable applications. These uses benefit from centralized analog-channel selection, reduced wiring complexity, and digital control of analog signals. In a data-acquisition system, the DG407DN+T can route multiple sensor or measurement inputs toward a shared converter while address logic selects the active source. PCB design should follow the package drawing and pin-description table in the Analog Devices datasheet, particularly for supply decoupling and the location of the common terminals. Allow adequate signal settling before sampling after a channel change, and evaluate the 200 ns switching interval together with source impedance, capacitance, and converter acquisition requirements. Guard against input overvoltage, and ensure that control levels meet the device's TTL- or CMOS-compatible logic requirements. This product record combines manufacturer application guidance, interface characteristics, package information, sourcing terms, and drop-in replacement analysis. It is intended to help engineers determine whether the DG407DN+T architecture, electrical limits, and 28-PLCC footprint fit a multiplexed analog signal-routing design.
DG407DW - Dual 8:1 CMOS Analog Multiplexer | Vishay
The Vishay Intertechnology DG407DW is a dual 8:1 CMOS analog multiplexer that routes one of eight differential inputs to a common differential output in each section. Its stated characteristics include 50 ohm on-resistance, 15 pC charge injection, a 200 ns transition time, 0.2 mW low power dissipation, and a maximum supply rating of 44 V. The device is offered in a 28-pin SOIC package for surface-mount PCB assembly. An analog multiplexer is an interface IC that connects multiple input channels to a shared signal path under digital control. The DG407DW belongs to the CMOS analog switch and multiplexer hierarchy, where low on-resistance preserves signal amplitude, low charge injection reduces switching errors, and short transition time supports higher-speed routing. Its dual differential architecture suits measurement systems requiring balanced input and output connections. Key features include two independent 8-channel differential sections, 50 ohm on-resistance, 15 pC charge injection, and a 200 ns transition time. The 44 V maximum supply rating provides additional operating headroom in industrial and instrumentation environments, while the 0.2 mW power figure highlights suitability for battery-operated and remote equipment. Reduced glitching and improved data throughput are explicit design goals of the DG407 family. The DG407 uses digital address and enable control to determine which differential input is connected to the output. Because it is a CMOS analog multiplexer rather than a digital logic device, its useful performance is governed by analog switching parameters such as on-resistance, off leakage, charge injection, and channel-transition behavior. Designers should evaluate those parameters against the bandwidth, source impedance, and acceptable settling error of the signal being routed. Typical uses include high-speed data-acquisition systems, audio signal routing, automatic test equipment, avionics, remote instrumentation, and battery-powered measurement products. In each case, the two differential multiplexer sections can route balanced sources while reducing wiring complexity. The manufacturer datasheet identifies low power dissipation and low on-resistance as especially useful for portable and precision signal-chain systems. PCB design should preserve the pin orientation, supply decoupling, and analog return paths recommended by the manufacturer. Input and output traces should be kept compact and away from high-energy switching nodes, while the address and enable traces should be routed to minimize coupling into the selected analog channel. System engineers should also account for charge injection and transition time when settling data after every address change. This product page combines the DG407DW operating characteristics with application guidance, package details, and a structured comparison against identified ordering alternatives. It is designed to help engineers select the correct mux configuration, plan layout and signal conditioning, and assess replacement options without overlooking analog switching constraints.
DG407DY - 16-Channel CMOS Analog Multiplexer | Renesas
The Renesas Electronics DG407DY is a single 16-channel or differential 8-channel CMOS analog multiplexer with a 28-pin SOIC package. It contains sixteen analog switches, supports TTL- and CMOS-compatible channel-selection logic, operates as an 8:1 multiplexer, and has a maximum on-resistance of 100 ohm. The device also includes a voltage reference for logic thresholds and an ENABLE input for controlling device selection when multiple multiplexers share a system. An analog multiplexer is an integrated switching circuit that connects one signal source to one of several channels according to digital address inputs. The DG407DY can route sixteen single-ended analog signals or eight differential signal pairs. This makes it useful for consolidating repetitive measurements, sharing scarce analog front ends, controlling sensor inputs, and expanding the number of signals handled by a single analog-to-digital converter. In the electronic-component hierarchy, it is a CMOS analog switch IC, an interface IC, and ultimately a semiconductor. The core benefits are integration and control simplicity. Sixteen switches, address decoding, threshold referencing, and enable control are combined on one device, reducing the number of discrete analog switches and associated routing components. The 100-ohm on-resistance specification supports the stated analog-switching role, while the 28-pin SOIC package provides a surface-mount implementation for compact industrial, instrumentation, and test systems. The manufacturer identifies the DG407 family as being in production. The DG407 uses digital select inputs to connect one common terminal to a selected channel. Its internal voltage reference establishes logic thresholds compatible with both TTL and CMOS control systems. The ENABLE input allows a system designer to place the device in an inactive state or use it to arbitrate access among multiple multiplexers. DG406 and DG407 devices are documented as drop-in replacements for the popular DG506A and DG507A series, providing a migration path when the older multiplexers are unavailable. Typical uses include multiplexed data acquisition, resistance and capacitance measurement systems, process-control interfaces, automated test equipment, battery and power-system monitoring, and general-purpose analog signal routing. The differential configuration is especially useful for paired sensor outputs, balanced measurement nodes, and systems where keeping source and return paths together reduces routing complexity. Designers should treat analog signal amplitude, bandwidth, charge injection, off-state leakage, logic levels, and injected noise as the principal switching considerations. Keep select and enable traces away from sensitive analog paths, use a common ground reference between the source, multiplexer, and receiving circuit, and decouple the supply close to the device. This page combines the DG407 architecture, sourcing guidance, design cautions, and documented legacy-device compatibility to support practical part selection.
DG408CJ+ - 8:1 CMOS Analog Multiplexer | Analog Devices
The Analog Devices DG408CJ+ is an improved 8-channel, single-ended CMOS analog multiplexer with one common output, packaged in a 16-pin PDIP. It selects one of eight analog inputs using three address inputs and an enable input, with a maximum on-resistance of 100 ohm. The device operates from a single +5 V to +30 V supply or from dual ±5 V to ±20 V supplies. An analog multiplexer is a semiconductor switching network that connects one of several input terminals to a shared output terminal. The DG408CJ+ belongs to the broader analog switch and multiplexer family, where CMOS construction provides low power consumption, TTL/CMOS-compatible address controls, and bidirectional signal conduction. Unlike a mechanical rotary switch, it can change channels electronically while maintaining a defined low on-resistance. Key electrical features include guaranteed matching between channels of 8 ohm maximum and on-resistance flatness of 9 ohm maximum across the specified signal range. Charge injection is limited to 15 pC maximum, while input off-leakage current is specified at 5 nA maximum at +85 °C. Rail-to-rail signal handling, ESD protection greater than 2000 V per MIL-STD-883 Method 3015.7, and low power consumption of 1.25 mW maximum support precision and instrumentation applications. The device uses three binary address lines to select one of eight channels. A low enable level places the multiplexer in shutdown mode, reducing power consumption and isolating the common output. Address and enable inputs accept TTL/CMOS logic levels, allowing direct control from common microcontrollers, FPGAs, and data-acquisition systems. The common output and individual inputs support analog signals referenced to the applicable positive or negative supply rails. Typical uses include multimeter and automated test equipment input switching, data-acquisition systems, industrial process measurement, sample-and-hold networks, and analog signal routing. The DG408CJ+ is especially useful when eight measurement sources must reach a shared amplifier, converter, or instrumentation amplifier while keeping channel resistance and injection error tightly controlled. Designers should confirm the supply configuration, logic thresholds, and signal amplitude before layout. Keep analog traces short, provide a stable ground reference, and use the pin-description table in the manufacturer data sheet when assigning PCB tracks. Allow settling time after changing the address or enable state because charge injection and parasitic capacitance can produce a transient step on the common output.
DG408CY+ - 8:1 CMOS Analog Multiplexer, 16-SOIC | Maxim Integrated
The Maxim Integrated DG408CY+ is an 8:1 CMOS analog multiplexer in a 16-pin narrow SOIC package, featuring 100Ω maximum on-resistance and 15pC maximum charge injection. It selects one of eight analog inputs through three digital control inputs and supports bidirectional signal conduction, making it suitable for multiplexed measurement, instrumentation, data acquisition, and control systems. The device also provides rail-to-rail signal handling, TTL/CMOS-compatible controls, and low power consumption of 1.25mW maximum. What is an analog multiplexer? An analog multiplexer is an analog switch that connects one common terminal to one of several input terminals. The DG408CY+ belongs to the CMOS analog switch and multiplexer hierarchy, where CMOS circuitry controls low-resistance, bidirectional signal paths. In a typical system, address logic selects a sensor, voltage source, or measurement channel, while the common terminal routes that signal to an ADC, amplifier, or signal-processing circuit. The DG408 can also be used as a demultiplexer when the design requires distributing a signal toward multiple destinations. Key verified features include guaranteed channel matching of 8Ω maximum, on-resistance flatness of 9Ω maximum, maximum on-resistance of 100Ω, and maximum charge injection of 15pC. Input off-leakage is specified below 5nA at 85°C. The device uses TTL/CMOS-compatible digital input control and includes ESD protection exceeding 2000V according to the listed product information. Its 16-pin narrow SOIC package supports conventional surface-mount assembly while keeping the analog signal routing compact. The improved DG408CY+ design emphasizes repeatable channel behavior across the specified signal range. This matters when multiple measurements are compared in instrumentation, automated test equipment, or data-acquisition systems because channel mismatch can create systematic measurement error. Its bidirectional conduction also allows the common signal path to be used according to the system architecture, although external protection and input-voltage limits must be respected. Typical uses include switching analog inputs into an ADC, selecting external sensors, routing test signals, implementing sample-and-hold front ends, and controlling laboratory or industrial measurement equipment. For high-impedance sources, leakage and off-state behavior can be important; for low-impedance signals, on-resistance and charge injection deserve attention. The DG408CY+ is therefore most appropriate when a compact, multiplexed analog-routing solution is needed with verified low-leakage and controlled charge-injection behavior. When laying out the circuit, keep analog traces short and route control signals away from sensitive analog nodes. Confirm that supply voltage, logic levels, input voltage range, and switch-cycle timing meet the device requirements before use. This page consolidates distributor information, verified datasheet features, package details, and design guidance for engineers evaluating the DG408CY+.
DG408CY+T - 8:1 CMOS Analog Multiplexer | Analog Devices
The Analog Devices DG408CY+T is an improved 8-channel, single-ended CMOS analog multiplexer with a 100 ohm maximum on-resistance, 16-SOIC package, and 8:1 channel configuration. Designed for multiplexing one of eight analog inputs into a common output, it uses TTL/CMOS-compatible address and enable controls and supports single or dual supply operation. An analog multiplexer is a switching interface that routes multiple analog signals through one shared output path. The DG408 family belongs to the analog switch and multiplexer hierarchy, where reduced channel count, low on-resistance, low charge injection, and controlled leakage become important when precision signals must be selected without introducing excessive error. This device can also operate in a demultiplexing arrangement when signal flow is reversed. Key characteristics include a maximum on-resistance of 100 ohms, 8 ohm maximum on-resistance flatness, and 9 pC maximum charge injection. Input off leakage is limited to 5 nA at +85 degrees Celsius, while the logic section accepts TTL/CMOS-compatible control levels. ESD protection exceeds 2000 V, and low power consumption is specified at a maximum of 1.25 mW. Rail-to-rail signal handling supports operation across the supplied analog signal range. The internal design uses eight CMOS analog switches, a digital decoder for channel selection, a voltage reference for logic thresholds, and an enable input for device selection when several multiplexers share a bus. Analog Devices describes the DG408 and DG409 as pin-compatible plug-in upgrades for the industry-standard DG408 and DG409 families, while Renesas identifies them as drop-in replacements for popular DG508A and DG509A devices. Typical uses include audio-signal routing, communication systems, data-acquisition equipment, guidance and control systems, sample-and-hold circuits, and test equipment. The 16-SOIC package supports conventional surface-mount assembly, and the DG408CY+T commercial-temperature ordering code targets operation from 0 to +70 degrees Celsius. Designers should account for charge injection during channel transitions and keep sensitive analog traces short and adequately decoupled. Supply rails, logic thresholds, signal amplitude, and the selected input channel must remain within the manufacturer’s operating limits. Because the device can conduct equally well in either direction, it is suitable for both multiplexing and demultiplexing. This page combines manufacturer specifications, package and temperature details, drop-in replacement information, and application-focused engineering guidance. It also highlights the measurable differences among compatible DG408 variants so that PCB reuse can be evaluated without overlooking temperature grade, package construction, or channel-selection requirements.
DG408DJ+ - 8-Channel 100Ω CMOS Analog Mux | Analog Devices
Analog Devices DG408DJ+ is an improved 8-channel, single-ended CMOS analog multiplexer with 100 ohm on-resistance, 8:1 signal routing, and a 16-pin PDIP package. Designed for bidirectional analog conduction, it connects one of eight inputs to a common output according to three binary address inputs, A0, A1, and A2. It can also be used as an 8-channel demultiplexer when signal-flow requirements permit. An analog multiplexer is a semiconductor switching network that routes multiple analog inputs onto a shared output path. The DG408DJ+ belongs to the analog switch and multiplexer hierarchy and combines eight switch elements, TTL/CMOS-compatible channel decoding, and device-enable control in one integrated circuit. This integration reduces discrete switching hardware in data-acquisition, test, communication, guidance, and control systems. The verified product information identifies a nominal 100 ohm on-resistance, 15 pC maximum charge injection, and input off-leakage below 5 nA at 85°C. Its equal bidirectional conduction makes the device suitable for routing signals where the source and destination roles can change. The three address inputs determine the selected channel, while the enable control allows the device to be removed from active service without changing the board interface. The DG408DJ+ is identified as an improved member of the DG408 family and as a pin-compatible upgrade for the industry-standard DG408. Analog Devices lists audio-signal routing, communication systems, data acquisition, guidance and control systems, sample-and-hold circuits, and test equipment among its applications. These uses illustrate why switching bandwidth, on-resistance, leakage, and control compatibility must be evaluated together. A primary design advantage is the ability to consolidate an eight-way analog routing matrix into one 16-pin IC. Logic-grounded address and enable signals control the selected path, while the common analog node reduces the number of external routing connections. Engineers should still verify signal amplitude, bandwidth, settling behavior, supply requirements, and all device limits against the current Analog Devices datasheet before releasing a production design. When sourcing a replacement, preserve the 16-pin PDIP footprint and confirm pin-level compatibility rather than relying only on the DG408 family name. Similar multiplexers can differ in address decoding, enable polarity, injection, leakage, supply range, and electrical performance. The official Analog Devices product page and datasheet remain the controlling sources for those details. This page combines verified distributor availability, manufacturer documentation, functional application analysis, and same-footprint replacement guidance. It is intended to help engineers identify the DG408DJ+, locate its documentation, understand its multiplexing role, and plan a technically defensible sourcing or replacement decision.
DG408DY+ - 8-Channel 100Ω CMOS Multiplexer | Analog Devices
Analog Devices DG408DY+ is a single 8-channel CMOS analog multiplexer with an 8:1 configuration, 100Ω maximum on-resistance, and a 16-SOIC package. Designed for routing one of eight analog inputs to a common output, it combines a TTL/CMOS-compatible decoder with low-power monolithic switch arrays for data acquisition, signal routing, test equipment, and instrumentation. An analog multiplexer is an interface IC that connects multiple input channels to one shared signal path. The DG408 family extends this hierarchy from analog switch to multiplexer, analog interface, and integrated circuit. Its eight independently addressed channels reduce the number of external pins and board-routing requirements when a system must sample or route several sensor, measurement, or test signals through one analog-to-digital converter or processing channel. Key features include a maximum on-resistance of 100Ω, guaranteed channel matching of 8Ω maximum, and signal-range flatness of 9Ω maximum. These specifications help minimize gain or attenuation differences among channels. The TTL/CMOS-compatible digital control accepts common logic levels, while the monolithic CMOS implementation supports low power dissipation for battery-operated and remote instrumentation systems. The DG408 architecture uses eight analog switches, a binary decoder, and a common output arrangement. Because it is a single-ended multiplexer, the DG408 routes eight channels to one output; the closely related DG409 provides a differential four-channel arrangement. Channel matching and flatness limits are particularly important when calibration assumes that all eight positions present nearly identical resistance. The 16-SOIC package supports conventional surface-mount PCB assembly. Typical applications include high-speed data acquisition, audio signal switching and routing, automatic test equipment, avionics, battery-powered instruments, and remote measurement systems. In each case, the multiplexer's low channel variation supports repeatable measurements, while its on-resistance remains suitable for many moderate-impedance sources. Signal bandwidth, input impedance, settling time, and source drive capability must be checked together when establishing an acquisition system's accuracy. For layout, keep the selected analog path short and route all eight channels consistently to reduce crosstalk and propagation mismatch. Place input protection and conditioning networks close to the mux pins, maintain a continuous ground reference, and avoid long parallel routes beneath noisy digital signals. Use the manufacturer's pin-description table when assigning supply, enable, address, common, and output connections. This product page combines the manufacturer's DG408 documentation with parameter-level comparison, replacement guidance, and practical PCB design considerations. It is intended to help engineers evaluate channel architecture, logic compatibility, package constraints, and signal-integrity requirements before integrating the DG408DY+ into a new analog routing system.
DG408DYZ - 8:1 CMOS Analog Multiplexer | Renesas Electronics
The Renesas Electronics DG408DYZ is a single 8:1 monolithic CMOS analog multiplexer with a 100 ohm maximum on-resistance, bidirectional analog channels, and a 16-pin SOIC package rated for industrial temperatures from -40 C to +85 C. It includes eight analog switches, TTL/CMOS-compatible channel decoding, an internal voltage reference for logic thresholds, and an ENABLE input for device selection when several multiplexers share a bus. An analog multiplexer is a switch matrix that routes one of several signal sources onto a shared output path. The DG408 belongs to the analog switch and multiplexer hierarchy, where its CMOS construction supports low power consumption and wide input voltage range compared with relay-based selectors. Its 8:1 configuration gives an eight-channel instrument, data-acquisition system, or automated test fixture a compact way to share one analog front end among multiple sources. The device uses three address lines for binary channel selection and an active-low or active-high ENABLE control according to the manufacturer logic specification. A TTL/CMOS-compatible decoder accepts standard logic levels, while the internal voltage reference establishes stable switching thresholds across supply conditions. Because the analog paths are bidirectional, the same DG408DYZ can be used to route a common signal toward one of eight external terminals as well as to select an incoming source. The DG408 series is documented as a drop-in replacement for the popular DG508A and DG509A families. Renesas also positions the DG408 and DG409 as pin-compatible single-ended 8-channel and differential 4-channel options respectively. The industrial DG408DYZ grade is suited to test and measurement, data acquisition, signal routing, control systems, and industrial interface boards where a SOIC footprint and deterministic logic decoding are preferred. Bidirectional operation simplifies PCB routing because the channel pins are not restricted to a dedicated input or output role. Nevertheless, keep all external analog nodes within the absolute maximum ratings listed in the manufacturer datasheet, and use input protection networks when signals can exceed the selected supply rails. Account for the 100 ohm maximum on-resistance when calculating source impedance, especially when driving high-impedance sensors or precision measurement chains. This page combines the manufacturer family information with distributor specifications, package details, equivalent-device references, and practical design guidance. It also identifies where a drop-in comparison should focus on package geometry, logic decoding, channel count, on-resistance, signal range, and temperature grade rather than on the DG408 name alone.
DG409AK - Dual 4:1 CMOS Analog Multiplexer | Analog Devices
Analog Devices DG409AK is a dual 4:1 CMOS analog multiplexer with two independently controlled circuits, a maximum on-state resistance of 100 ohms, channel matching of 1.5 ohms, and switching times of 150 ns maximum. The device is packaged in a 16-pin CERDIP package for through-hole industrial, instrumentation, test, measurement, data-acquisition, and signal-routing systems. An analog multiplexer is an interface IC that connects one of several analog inputs to a shared output while minimizing signal-path distortion. In the broader semiconductor hierarchy, the DG409AK belongs to the analog switch and multiplexer class, the interface IC family, and ultimately the broader semiconductor category. Its two 4:1 sections allow two signals to be routed independently, reducing the number of external switches required in measurement and control equipment. The DG409AK supports single-supply operation from 5 V to 30 V and dual-supply operation from ±5 V to ±20 V. Low on-state resistance limits insertion loss, while the specified 1.5-ohm channel-to-channel matching helps preserve amplitude consistency between selected channels. Maximum turn-on and turn-off times of 150 ns support rapid control sequencing, although propagation delay, charge injection, and off-state isolation must also be considered in precision applications. Internally, the device uses CMOS analog-switching structures controlled by TTL- or CMOS-compatible digital inputs. Independent select and enable controls allow each multiplexer section to route signals when required. The Analog Devices DG409 family documentation emphasizes guaranteed channel matching, on-resistance flatness over the specified signal range, low charge injection, low input leakage, low power consumption, rail-to-rail signal handling, and ESD protection greater than 2000 V. Typical applications include multimeter and bench-instrument signal selection, automated test equipment, industrial data acquisition, sensor-interface routing, and control systems that must select several analog inputs without adding a separate analog switch for every channel. The 16-pin CERDIP package also suits legacy equipment where through-hole construction and a stable industrial footprint are important. Designers should verify supply voltage, input-signal range, logic thresholds, leakage, charge injection, and switch timing against the exact operating conditions. A low-impedance source, adequate input protection, and clean grounding help preserve measurement accuracy. Because the DG409AK is listed as obsolete, new production designs should evaluate current DG409-family options and confirm availability, lifecycle, and pin compatibility before committing a layout. This page combines the DG409AK functional description, verified electrical characteristics, practical application guidance, package considerations, and a conservative drop-in comparison. It is intended to help engineers distinguish true legacy replacements from parts that only share the DG409 name or general multiplexing function.
DG409CJ+ - Dual 4:1 CMOS Multiplexer | Analog Devices
Analog Devices DG409CJ+ is a dual 4:1 CMOS analog multiplexer with 100 ohm maximum on-resistance, 150 ns switching performance, and a 16-pin DIP package. The device supports supply voltages from 5 V to 30 V, operates as two independent 4-position analog switches, and provides break-before-make behavior for applications requiring isolated signal paths. An analog multiplexer is an interface IC that routes one of several input signals to an output terminal under digital control. The DG409 family is described as an improved 8-channel or dual 4-channel CMOS analog multiplexer. In each 4:1 section, four inputs share one output, while separate address-select inputs determine the active path. This places the device in the analog switch and multiplexer hierarchy within broader signal-routing and interface semiconductor systems. Key features include a maximum on-resistance of 100 ohm, 150 ns switching time, low off leakage current of 500 pA, and operation across a 5 V to 30 V supply range. The manufacturer also identifies guaranteed channel matching of 8 ohm maximum and signal-range flatness of 9 ohm maximum for the redesigned DG408 and DG409 families. These characteristics help minimize gain error, channel-to-channel mismatch, and distortion when routing precision analog signals. The DG409CJ+ uses CMOS multiplexing architecture with separate control logic for the two 4:1 sections. Break-before-make switching prevents the incoming and outgoing paths from conducting simultaneously during transition, reducing signal contention in test, measurement, and instrumentation systems. The 16-DIP package provides through-hole mounting and approximately 7.62 mm lead pitch according to the verified distributor listing. Typical uses include automated test equipment, data acquisition, analog signal routing, industrial control, instrumentation, and communications systems. One multiplexer section can select among four sensor outputs while the other routes a separate group of four inputs, allowing a compact dual-bank routing architecture. Designers must also account for the relatively high on-resistance compared with modern low-resistance multiplexers when driving high-impedance or high-capacitance loads. For PCB design, place the DG409CJ+ close to the routed analog signals to minimize trace capacitance and pickup. Confirm logic levels and supply tolerances before decoding address inputs, and verify downstream loading because the 100 ohm maximum path resistance can create signal attenuation with a finite input impedance. This page combines verified manufacturer and distributor information, drop-in family alternatives, application guidance, and a parameter-by-parameter comparison. It also identifies unavailable electrical details explicitly rather than estimating unverified values, helping engineers evaluate the DG409CJ+ for new designs and legacy replacements.
DG409CUE+ Dual 4:1 CMOS Multiplexer | Maxim Integrated
The Maxim Integrated DG409CUE+ is a dual 4:1 CMOS analog multiplexer with two independent 4:1 switching circuits, a maximum on-resistance of 100 ohms, and a 16-pin TSSOP package. It operates with supply voltages up to +30 V for single-supply operation and up to ±20 V for dual-supply operation, making it suitable for routing bipolar or unipolar analog signals. A CMOS analog multiplexer is an interface IC that connects multiple signal inputs to a shared output under digital control. Each DG409CUE+ circuit uses address and enable logic to select one of four inputs. The DG409 family belongs to the broader analog switch and multiplexer hierarchy, where low on-resistance, predictable channel behavior, and controlled switching are central to accurate signal routing. The DG409CUE+ provides improved matching between channels, guaranteed at 8 ohms maximum, and flatness over the specified signal range of 9 ohms maximum. Its 100-ohm maximum on-resistance limits signal attenuation when the device routes low-frequency analog signals. ESD protection greater than 2,000 V according to MIL-STD-883 Method 2002 adds handling protection for the switching pins. The device is designed for both single-ended and balanced routing architectures. Two multiplexers in one package can implement a 4:1 analog selection function, a dual-channel instrumentation interface, or a paired differential signal path. Its CMOS implementation supports bidirectional analog conduction, allowing the selected terminals to serve as inputs or outputs as required by the circuit topology. Typical applications include data acquisition, sample-and-hold systems, battery monitoring, test equipment, signal routing in industrial controls, and precision analog measurement. The dual 4:1 organization is particularly useful when two related signals must be selected simultaneously, such as differential sensor outputs, although the address and enable timing should be coordinated to prevent unintended channel transitions. PCB layout should minimize resistance and inductance in analog signal paths. Place the TSSOP-16 device close to connector and measurement circuitry, route selected and unselected analog terminals away from fast digital clocks, and use a solid ground plane. Supply bypassing should be placed at the power pins, while address and enable traces require clean return paths to prevent switching transients from coupling into the selected channel. This page combines the device's key electrical characteristics, functional positioning, application guidance, design precautions, and compatibility analysis. It also provides practical criteria for determining when the DG409CUE+ fits a routing requirement and when a different package or multiplexer architecture should be selected.
DG409CY+T - Dual 4:1 CMOS Analog Multiplexer | Analog Devices
The Analog Devices DG409CY+T is an improved dual 4:1 CMOS analog multiplexer with two independently selectable switch functions, 100 ohm maximum on-resistance, and bidirectional signal conduction. The device is packaged in a 16-pin narrow SOIC and is intended for analog signal routing in test equipment, instrumentation, communication systems, and data-acquisition systems. A CMOS analog multiplexer is an electronic switching network that connects one common terminal to one of several input terminals. Its hierarchy is analog switch, multiplexer or demultiplexer, interface IC, and integrated circuit. By applying binary select signals, the DG409 routes analog signals among multiple sources while presenting a compact alternative to discrete relays or multiple analog switches. Bidirectional operation allows the same device to work as either a multiplexer or a demultiplexer. The improved DG409 family provides guaranteed channel matching of 8 ohms maximum and on-resistance flatness of 9 ohms maximum across the specified signal range. Its maximum on-resistance is 100 ohms, while maximum charge injection is 15 pC. These characteristics make the DG409CY+T appropriate for instrumentation where channel-to-channel resistance consistency, signal fidelity, and low switching disturbance are more important than very low resistance alone. The DG409 family uses CMOS technology and supports two 4:1 switching functions. Low input off-leakage of less than 5 nA at 85 degrees Celsius helps preserve the state of high-impedance nodes between selections. The device can also be used as a demultiplexer because every switch path conducts equally well in either direction. Its dual architecture allows one multiplexed signal and one demultiplexed signal, or two multiplexed functions, to be handled in one package. Typical uses include routing sensor outputs into an analog-to-digital converter, selecting external test stimuli for automated test equipment, connecting instrumentation channels, and implementing communication-signal path selection. The DG409CY+T is especially appropriate where a compact 16-pin surface-mount package, bidirectional conduction, and controlled channel matching are desired. The industrial-temperature ordering information should be checked against the exact suffix and datasheet ordering table. PCB design requires care because analog switches inject charge when changing state and can couple transient disturbance into high-impedance nodes. Place the device close to the source and destination signals, keep sensitive traces away from select-line transitions, and provide a quiet ground reference. The SOIC footprint simplifies mixed-signal assembly, but the exposed pad is not applicable to this 16-pin package. This page combines the manufacturer product information, distributor records, package details, documented switch characteristics, comparison data, and practical PCB guidance. It also distinguishes the tape-and-reel DG409CY+T ordering code from related DG409 variants and identifies which replacement candidates are supported by the available cross-reference records.
DG409DJ+ - Dual 4-Channel CMOS Multiplexer | Analog Devices
The Analog Devices DG409DJ+ is an improved dual 4-channel CMOS analog multiplexer with 100 ohm on-resistance, 15 pC maximum charge injection, and operation from 5 V to 30 V in a 16-pin PDIP package. It supports bidirectional signal conduction and can also operate as a demultiplexer, making it suitable for analog routing, data acquisition, test equipment, communication systems, audio-signal routing, and sample-and-hold circuits. An analog multiplexer is an interface-switching IC that selects one of several analog terminals and connects it to a common output. The DG409 belongs to the CMOS analog multiplexer hierarchy, alongside demultiplexers and analog switches. Its digital address and control inputs determine the selected channel, while the internal CMOS switch array routes the selected analog signal in either direction. Key features include two independent 4-channel sections, low on-resistance, low charge injection, low off leakage, and guaranteed channel matching and flatness over the specified signal range. The verified product information identifies the device as an improved replacement-compatible mux family and lists 4:1 operation, 100 ohm on-resistance, a 16-pin PDIP package, and a 5 V to 30 V supply range. The device uses TTL/CMOS-compatible decoding logic, allowing it to be controlled by common digital interface voltages. Its multiplexed architecture reduces the number of external signal lines needed when several analog sources must be routed to one processing channel. Because the switch conducts equally well in both directions, the same device can support routing and demultiplexing arrangements when system timing and signal polarity are suitable. Typical applications include audio-signal routing, communication systems, data-acquisition systems, guidance and control systems, sample-and-hold circuits, and test equipment. In these systems, the DG409DJ+ can select among multiple sensors, instrument channels, or signal sources before conversion, amplification, measurement, or further processing. For PCB design, preserve the PDIP pin mapping and route analog traces away from high-current switching nodes. Confirm supply voltage, logic levels, signal amplitude, channel timing, leakage, and off-state behavior against the manufacturer datasheet. The verified data does not provide complete pricing, electrical limits, or a full pin list, so those values must be confirmed before release to production.
DG409DVZ - 4:1 CMOS Analog Multiplexer | Renesas
The Renesas Electronics DG409DVZ is a 2-circuit, 4:1 CMOS analog multiplexer with a 100 ohm on-resistance, bidirectional analog channels, and a 16-pin TSSOP package. It operates across a -40°C to +85°C temperature range and supports single-ended 8-channel or differential 4-channel routing through an array of eight analog switches. An analog multiplexer is an interface IC that connects multiple signal sources to a shared amplifier, converter, or measurement channel. The DG409 belongs to the broader CMOS analog switch and multiplexer hierarchy, where digital address inputs select an analog path while an enable input determines whether that path is connected. Bidirectional channels permit signal flow in either direction, which makes the device useful for routing, sharing, and test systems. Key features include a 4:1 selection ratio, two operating circuits, 100 ohm on-resistance, bidirectional channels, and TTL/CMOS-compatible decoding. The digital control interface uses three select inputs to address the active channel and one enable input for device gating. An internal voltage reference provides stable logic thresholds, allowing the address and enable signals to operate reliably with both TTL and CMOS logic families. The monolithic CMOS implementation places eight switches, address decoding, threshold reference, and enable control into one integrated circuit. This arrangement reduces the number of external routing components while preserving a compact 16-TSSOP surface-mount footprint. Differential operation supports balanced signal pairs, while the same device architecture can implement single-ended multiplexing when the appropriate channels are wired for that function. Typical uses include data acquisition systems, instrument signal routing, automated test equipment, industrial control interfaces, communication-channel selection, and precision measurement front ends. Differential routing is particularly useful when the selected pair carries a balanced sensor, amplifier, or converter channel that would benefit from matched signal paths. Designers should verify the supply range, absolute maximum ratings, logic levels, channel configuration, and switching timing in the manufacturer datasheet before finalizing the PCB. Input and output signals must remain within the specified analog range, and the enable state should be controlled during power-up to prevent unwanted paths from being connected.