Interface ICs
ژێرپۆلەکان
بەرهەمەکان (5,100+)
ADM208ANZ - 4/4 RS-232 Transceiver, 200 kbps | Analog Devices
Analog Devices ADM208ANZ is a four-driver, four-receiver RS-232 transceiver with 0.1 µF charge-pump capacitors, 5 V CMOS operation, and a data rate up to 200 kbps, packaged in a 24-pin PDIP. The device provides full RS-232 signal conditioning for data-terminal equipment and data-communication equipment requiring multiple bidirectional serial channels. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232-compatible levels and converts received RS-232 levels back into digital logic. The ADM208ANZ combines four drivers and four receivers in one package, reducing the number of interface components required in multi-port equipment. It is particularly useful when the design must generate bipolar RS-232 voltages from a single 5 V supply. Key features include four drivers and four receivers, 200 kbps maximum data rate, single +5 V CMOS supply operation, and integrated on-board dc-to-dc converters that produce approximately ±9 V output swing. Only 0.1 µF capacitors are required for charge-pump operation. The industrial-grade option operates across a -40°C to +85°C temperature range and is supplied in a through-hole PDIP package. The ADM208ANZ architecture allows a compact RS-232 implementation without external bipolar power rails. Its four transmitters add RS-232-level outputs for outbound serial data, while its four receivers accept incoming RS-232 signals. Because the interface combines eight channels in one device, designers can support multiple connections while limiting the number of data-conversion ICs and associated board area. Typical applications include industrial data acquisition, test and measurement equipment, barcode and point-of-sale systems, computer peripheral interfaces, and embedded control systems communicating with legacy RS-232 equipment. For each channel, the logic-side ground, driver outputs, receiver inputs, supply rails, and charge-pump capacitors must be routed according to the manufacturer's application diagram. When laying out the board, place the 0.1 µF charge-pump capacitors close to their designated pins and keep RS-232 traces away from sensitive analog or high-speed digital paths. Use the receiver and driver enable or shutdown controls only after confirming the exact behavior of the selected ordering code. Maintain suitable ground-return paths and observe the absolute maximum ratings in the manufacturer datasheet. This product page combines the Analog Devices product information, distributor package details, RS-232 interface context, practical application guidance, and same-package replacement analysis. It is intended to help engineers verify supply, channel count, package, speed, pinout, and lifecycle considerations before integrating the ADM208ANZ into a serial interface design.
ADM208AR - 200 kbps 4/4 RS-232 Transceiver | Analog Devices
The Analog Devices ADM208AR is a +5 V CMOS RS-232 transceiver with four drivers, four receivers, a 200 kbps data rate, and a 24-pin SOIC package. It is designed for single-supply EIA-232-E and V.28 communications interfaces where a 12 V supply is unavailable. The verified manufacturer page identifies the device as a 0.1 µF, +5 V, 4-driver and 4-receiver RS-232 transceiver. An RS-232 transceiver is an interface IC that converts logic-level signals between a host or controller and a cable-based RS-232 link. The driver channels translate CMOS levels into RS-232-compatible bipolar signals, while the receiver channels convert those signals back into CMOS logic. As a result, the ADM208AR belongs to the RS-232 interface IC, communications transceiver, line-driver/receiver, and power-management interface hierarchy. Key verified features include four drivers and four receivers, operation from a single +5 V supply, 0.1 µF charge-pump capacitors, and a data rate listed by the official product page as 200 kbps. The manufacturer describes the ADM2xx family as robust RS-232 and V.28 interface devices intended for communications systems that do not have a 12 V rail. Additional detailed electrical, environmental, and package values require confirmation in the manufacturer datasheet. The ADM208AR is useful for industrial control links, equipment-to-console connections, embedded serial ports, point-of-sale equipment, and test systems requiring more than two RS-232 channels. Its four-channel arrangement reduces the need for multiple interface packages when several point-to-point RS-232 links share the same +5 V system supply. The 24-SOIC package is also suitable for conventional surface-mount PCB assembly. Designers should verify every unused driver output and receiver input, preserve the required charge-pump capacitor arrangement, and treat the RS-232 cable interface as a physically isolated communication environment rather than a high-speed differential link. The verified snippets identify the device as a plug-in upgrade family relative to MAX205-211 and MAX213 parts, but each replacement must still be checked against the exact pinout, supply requirements, and timing ratings. For a new layout, use the exact package drawing and pin table from the Analog Devices datasheet before routing. Confirm the external capacitor values, supply decoupling, logic levels, receiver thresholds, and maximum cable-side voltage levels against the latest manufacturer documentation. Pricing and availability should be checked as of 2026-10-22 because distributor commercial terms can change independently of the component's electrical design. This page synthesizes the verified ADM208AR product description, distributor package information, and practical RS-232 design considerations. It does not infer unreported electrical limits or invent replacement specifications; unavailable values are explicitly marked for engineering verification.
ADM208ARS - 4/4 RS-232 200kbps IC | Analog Devices
Analog Devices ADM208ARS is a +5 V powered CMOS RS-232 interface IC containing four drivers and four receivers in an SSOP package. It supports data rates up to 200 kbps and uses 0.1 µF external charge-pump capacitors. According to the Analog Devices ADM208 product page and data sheet, the ADM208 family is in production and provides a 9 V output swing from a +5 V supply. An RS-232 transceiver is an interface IC that converts logic-level digital signals into RS-232 line levels and converts received RS-232 signals back into CMOS-compatible logic. Within the signal-chain hierarchy, the ADM208ARS is a multi-channel line transceiver, placing it between low-voltage digital controllers and external RS-232 equipment such as computers, peripherals, modems, printers, and instruments. The four-driver, four-receiver arrangement provides eight independently usable RS-232 channels in one package. Key operating characteristics include a maximum data rate of 200 kbps, low power consumption of 15 mW as stated in the verified feature summary, and external charge-pump capacitors of 0.1 µF. The ADM208 family also provides 9 V output swing with a +5 V supply and receiver input levels rated to 30 V. The +5 V single-supply architecture simplifies power planning in systems that already operate from 5 V. Internally generated charge-pump voltage raises the driver output above the normal supply rail, allowing the device to meet RS-232 output voltage requirements without a separate negative supply. The ADM208 data sheet also identifies the family as a plug-in upgrade for MAX205, MAX211, and MAX213 devices, providing a useful basis for compatibility assessment when evaluating board revisions. Typical applications include multi-channel data acquisition, industrial instrumentation, printer and modem interfaces, computer peripherals, and embedded serial-port systems. Four transmitter and four receiver channels also allow one controller to communicate with several RS-232 devices or support bidirectional links on fewer physical lines. The principal design consideration is ensuring adequate charge-pump capacitor selection and placement. The verified data identifies 0.1 µF capacitors, so designers should follow the manufacturer’s recommended capacitor type, voltage rating, and PCB layout to obtain the specified 200 kbps operation and dependable line-driver behavior.
ADM208ARZ - 4/4 RS-232 Transceiver, 5V, 24-SOIC | Analog Devices
Analog Devices ADM208ARZ is a four-driver, four-receiver RS-232 transceiver operating from a single 5 V supply, with on-board dc-to-dc converters producing approximately ±9 V output swing. It is packaged in a 24-pin SOIC and supports data rates up to 200 kB/s. The ADM208ARZ is designed for EIA-232-E and V.28 interfaces where ±12 V supplies are unavailable. An RS-232 transceiver is an interface IC that combines voltage-level drivers and receivers for serial data links. In the signal-path hierarchy, the ADM208ARZ is an RS-232 transceiver, also called a line-driver/receiver IC, within the broader interface-IC and semiconductor categories. Its integrated charge-pump converters allow a single-ended 5 V system supply to communicate with conventional ±12 V RS-232 equipment without external power rails. The ADM208ARZ integrates four RS-232 drivers and four receivers in one package. The manufacturer specifies 200 kB/s operation, low power consumption of 15 mW, and an output swing of approximately ±9 V from a 5 V supply. Charge-pump capacitors may range from 0.1 µF to 10 µF, while receiver inputs tolerate voltages to ±30 V, improving robustness against accidental RS-232-level voltage exposure. These characteristics make the device suitable for multi-channel industrial control, data acquisition, test equipment, and legacy peripheral connections. The internal architecture uses charge-pump circuitry to develop the negative voltage required by the RS-232 drivers. Four transmit channels independently convert TTL or CMOS logic levels into bipolar RS-232 signals, while four receive channels convert bipolar RS-232 inputs into TTL-compatible logic. The device supports the MAX206 through MAX211 and MAX213 families' pin-compatible interface arrangements, which can simplify qualification of equivalent interface hardware when the electrical ratings remain acceptable for the target design. Typical applications include four-wire RS-232 links between industrial controllers and instrumentation, laboratory test systems, point-of-sale equipment, printers, and legacy computers. Because four driver and receiver channels are combined in one device, it can reduce component count and board area in multi-port systems. The 5 V supply architecture also avoids generating ±12 V externally in equipment where the enclosure and power budget are constrained. Design attention should be paid to charge-pump capacitor selection, ground integrity, and the separation between sensitive receive paths and high-energy driver outputs. Place the required capacitors close to their associated pins, use a low-impedance ground plane, and route the receive and transmit nets to avoid parallel runs that could couple edge noise into receiver inputs. Confirm the selected capacitor voltage rating and ESR behavior against the device's recommended operating conditions. This product page combines the manufacturer's interface specifications with practical pin, replacement, and layout guidance. It also distinguishes true 24-pin drop-in alternatives from devices with different channel counts or package footprints, helping engineers evaluate board reuse without assuming that every RS-232 transceiver is electrically or mechanically interchangeable.
ADM208EAN - 4/4 RS-232 Transceiver | Analog Devices
The Analog Devices ADM208EAN is a four-driver, four-receiver RS-232 transceiver designed for +5 V CMOS systems, with 0.1 µF charge-pump capacitors and data rates up to 200 kBPS. The device is packaged in a 24-pin plastic DIP (24-PDIP) package and is identified by the ADM208EAN order code. An RS-232 transceiver is an interface IC that combines the electrical driver and receiver functions required to connect CMOS logic with RS-232 serial equipment. The ADM208EAN provides four transmit channels and four receive channels, allowing one device to support multiple serial links or a combination of data, control, and status signals. It belongs to the broader line-driver and receiver hierarchy within interface ICs. The manufacturer describes the ADM208 family as a +5 V CMOS RS-232 transceiver with four drivers and four receivers. Its 200 kBPS data rate is suitable for industrial-control, communications, instrumentation, and legacy peripheral interfaces where RS-232 remains required. The 0.1 µF charge-pump capacitor specification supports a compact implementation, while the integrated transceiver reduces the number of separate driver and receiver packages needed on the board. EMI and EMC protection are important considerations for RS-232 equipment because external cables can introduce electrostatic discharge and conducted or radiated noise. The ADM208EAN documentation identifies ±15 kV ESD protection, including air-gap discharge, contact discharge, and human-body-model protection. The documentation also references fast-transient-burst immunity and low EMI emissions under EN 55022. The ADM208EAN is suitable for equipment that needs several bidirectional or unidirectional RS-232 connections near a system edge. Industrial controllers, test equipment, data-acquisition systems, and legacy computer interfaces can use the four drivers and four receivers to reduce component count while keeping the RS-232 electrical interface standardized. The CMOS supply arrangement also helps interface directly with modern digital logic families. Designers should use the pin-description and typical-application information in the manufacturer data sheet when assigning signals, placing protection devices, and selecting bypass capacitors. RS-232 voltage levels, cable length, grounding, and connector exposure should be checked against the system EMC and ESD requirements. The ADM208EAN is a production device listed by Analog Devices with a product page and current manufacturer documentation. This product data combines the manufacturer family description, distributor identification, RS-232 application context, and engineering guidance for EMI, ESD, PCB layout, and system integration.
ADM208EAR - 4/4 RS-232 Transceiver, 200kbps | Analog Devices
The Analog Devices ADM208EAR is a four-driver, four-receiver RS-232 interface transceiver operating from a single 5 V supply, with a data rate up to 200 kbps in a 24-lead SOIC package. It provides the charge-pump circuitry and level translation needed to connect modern CMOS logic to RS-232 line drivers and receivers without requiring a separate negative supply. The device is intended for industrial, instrumentation, data-acquisition, and embedded equipment requiring a robust EIA-232 and CCITT V.28 interface. An RS-232 transceiver is an interface IC that translates low-voltage digital signals into RS-232-compatible line levels and converts received line levels back into CMOS-compatible logic. The ADM2xxE family belongs to the broader hierarchy of transceiver IC, interface IC, communications IC, and semiconductor. Unlike a simple RS-232 driver or receiver, this integrated device combines four transmitters and four receivers, making it useful where multiple serial channels must share one board. The ADM208EAR's principal features include a single 5 V supply, 0.1 µF charge-pump capacitors, four RS-232 drivers, four RS-232 receivers, and operation at up to 200 kbps. The manufacturer identifies the device as compliant with the EU EMC Directive 89/336/EEC. Its listed electrostatic-discharge protection reaches 15 kV for human-body-model and air-gap discharge and 8 kV for contact discharge. It also meets fast-transient burst-immunity requirements under IEC 1000-4-4 and low-emissions requirements under EN55022. The integrated charge-pump design creates the positive and negative voltage levels required by RS-232 while allowing the interface to operate from only one 5 V rail. Four drivers make it appropriate for equipment that must support multiple outbound serial channels, while four receivers support multiple inbound channels. A maximum data rate of 200 kbps accommodates legacy industrial peripherals, laboratory instruments, and control equipment that operate below the highest RS-232 rates available in newer interface families. Typical uses include multi-channel industrial controllers, data-logging systems, test and measurement instruments, service interfaces, and embedded serial-port concentrators. Its 24-lead SOIC package provides more I/O than a 16-pin dual transceiver while remaining suitable for conventional through-hole or surface-mount PCB assembly. In systems with several legacy peripherals, the four-channel architecture can reduce the number of separate driver and receiver ICs required. Circuit design should follow the manufacturer's recommended capacitor connections and keep the charge-pump and interface traces compact. Place the required 0.1 µF capacitors close to their designated pins, provide a stable 5 V rail, and route each RS-232 signal away from sensitive analog and high-speed digital paths. External protection may still be considered for cables connected to unprotected external equipment, even though the device includes substantial ESD protection. This product page organizes the ADM208EAR specifications, lifecycle status, package information, drop-in alternatives, application guidance, and design notes into one engineering reference. It also distinguishes the four-channel ADM208EAR from nearby interface ICs by package, channel count, data rate, protection, and control features so engineers can make a board-level compatibility decision before purchasing.
ADM208EARS - Quad RS-232 Transceiver | Analog Devices
The Analog Devices ADM208EARS is a four-driver, four-receiver RS-232 transceiver operating from a single +5 V supply in a 24-pin SSOP package. It supports data rates up to 230 kbps, implements four transmit channels and four receive channels, and is designed for EIA-232-E and CCITT V.28 interfaces. The device also provides ±15 kV ESD protection for ports exposed to electrostatic discharge during industrial, communications, and instrumentation applications. An RS-232 transceiver is an interface IC that converts logic-level signals between a host or controller and the voltage levels used by RS-232 communications links. It belongs to the line-driver and line-receiver hierarchy, combines bidirectional interface channels in one package, and removes the need for separate driver and receiver ICs when several serial ports share the same board. The ADM208EARS provides a 4.5 V to 5.5 V operating supply range and approximately 13 mA operating supply current. Four driver outputs support point-to-point RS-232 links, while four receiver inputs support independent receive channels. Its 230 kbps maximum data rate supports legacy serial communications, industrial equipment, data acquisition, point-of-sale terminals, and control systems that rely on the established RS-232 electrical interface. The single-supply architecture simplifies power planning compared with conventional RS-232 implementations requiring positive and negative rails. Internal level translation allows CMOS or TTL-compatible logic signals to connect to RS-232 lines. The E suffix identifies the enhanced device family, whose published features include conformance with EIA-232-E and CCITT V.28, EMI/EMC protection considerations, and enhanced ESD protection. The ADM208EARS is offered in a 24-pin SSOP package for compact surface-mount designs. Typical uses include multi-port instrumentation, test equipment, industrial controllers, security systems, and service interfaces. Four transmitters and four receivers can support several unidirectional or full-duplex RS-232 connections when the port allocation permits. The device is particularly useful when a design needs multiple RS-232 channels without allocating separate packages for every driver and receiver. Place the 0.1 µF decoupling capacitor close to the +5 V supply pin and ground return, and route each interface trace to minimize exposure to fast-edge and ESD events. Confirm signal polarity, receiver thresholds, and connector-side protection against the pin-description table in the manufacturer datasheet before assigning PCB nets. This product record combines interface architecture, operating limits, package details, practical decoupling guidance, and a pin-compatible substitution review. It is intended to help engineers select the correct quad transceiver, plan a reliable RS-232 port, and distinguish functional compatibility from changes that require board-level validation.
ADM208EARU - 230kbps 4-Channel RS-232 | Analog Devices
The Analog Devices ADM208EARU is a four-driver, four-receiver full RS-232 interface transceiver operating from a single 5 V supply at data rates up to 230 kbps. The device is offered in a 24-lead TSSOP package and is designed for robust EIA-232E and CCITT V.28 serial-interface applications. It integrates four transmit channels and four receive channels, allowing two complete RS-232 links or several unidirectional data paths to be implemented in a compact surface-mount design. An RS-232 transceiver is an interface IC that translates logic-level digital signals into RS-232 line levels and converts incoming line-level signals back into logic-level outputs. The ADM2xxE family belongs to the RS-232 transceiver hierarchy within interface ICs and broader semiconductor signal-conditioning devices. These devices bridge modern controller logic and the voltage, noise-immune signaling used by older computer, industrial, instrumentation, and communications equipment. Key features include four RS-232 drivers, four RS-232 receivers, operation from one 5 V supply, and a maximum data rate of 230 kbps. According to the Analog Devices ADM208E product information, the family conforms to the EIA-232E and CCITT V.28 specifications. The ADM208EARU also belongs to the robust ADM2xxE product family, which is associated with EMI/EMC compliance and ±15 kV ESD protection. Its 24-lead TSSOP format supports compact PCB layouts while retaining separate driver and receiver channels. Technically, the driver channels provide the bipolar voltage swings required for RS-232 communication, while the receiver channels detect and translate incoming line states into CMOS-compatible logic. The 5 V-only architecture simplifies system power design compared with dual-supply RS-232 solutions. Because RS-232 is a point-to-point, unbalanced interface, correct grounding, cable length, connector selection, and protection-network design remain important system-level considerations even when the IC itself is robust. Typical uses include industrial control links, test and measurement equipment, data acquisition systems, service interfaces, point-of-sale equipment, and embedded systems that retain an RS-232 port. The four transmitters and four receivers make the device especially useful where multiple serial channels must be accommodated without using four separate single-channel transceivers. Systems can also assign unused channels or operate them in one-way configurations when the application does not require four full duplex links. Place the device close to the RS-232 connector and route the high-voltage driver outputs directly toward protected connector pins. Keep logic-side traces away from these outputs to minimize capacitive coupling and crosstalk. Use the manufacturer pin-description table when assigning supply, ground, enable, shutdown, driver-output, and receiver-input nets, and follow the datasheet layout guidance for external protection components and bypass capacitance. This product page combines the official family specifications with practical channel-assignment, signal-routing, and replacement guidance. It also helps engineers distinguish the ADM208EARU from lower-channel RS-232 devices that use different packages or pin assignments, supporting faster component selection before PCB layout begins.
ADM208EARZ - 4/4 RS-232 Transceiver, 230 kbps | Analog Devices
The Analog Devices ADM208EARZ is a four-driver, four-receiver RS-232 transceiver designed for single-supply EIA-232 and V.28 communications interfaces. It operates from a 4.5 V to 5.5 V supply, supports data rates up to 230 kbps, and is packaged in a 24-pin SOIC. The device uses CMOS-compatible 0.1 µF charge-pump capacitors for operation from a single +5 V rail. An RS-232 transceiver is an interface IC that converts logic-level signals into differential voltage levels for transmission and converts received RS-232 signals back into logic-compatible levels. In the product hierarchy, the ADM208EARZ belongs to the RS-232 interface transceiver class within interface ICs and broader data-communication semiconductors. Its four transmitters and four receivers support multiple point-to-point serial links in one package, reducing board area compared with separate line-driver and receiver devices. The ADM208 family is specified for harsh electrical environments and operates at rates up to 230 kbps. According to Analog Devices, the devices fully conform to EIA-232E and V.28 specifications. The ADM208EARZ also provides ±15 kV ESD protection, making it appropriate for industrial equipment and external serial ports where electrostatic discharge is a practical concern. A Schmitt-trigger receiver helps improve noise immunity when signals arrive with slow or noisy transitions. The charge-pump architecture generates the positive and negative voltage levels required by RS-232 without a dual supply. A 0.1 µF capacitor is specified for the charge-pump circuit, while the standard 5 V interface rail requires normal supply bypassing. Because the charge-pump switching action can introduce ripple, careful component selection and placement around the ADM208EARZ remain important when connecting external cables. Typical uses include industrial serial controllers, point-of-sale terminals, data-acquisition equipment, test systems, and embedded products that need to communicate with legacy RS-232 peripherals. Four driver and receiver channels make the device useful for multiport equipment, custom service interfaces, and systems that combine data transmission and reception on one board. For PCB design, place the charge-pump capacitor and supply-decoupling capacitors close to their associated pins. Keep the RS-232 driver outputs away from sensitive receiver inputs and reduce trace length where practical. Confirm signal polarity, grounding, and cable-side protection because logic-level standards and RS-232 voltage conventions differ at the host interface. This page combines the ADM208EARZ device specifications, package and commercial information, verified drop-in references, parameter comparisons, and practical PCB guidance to help engineers evaluate the transceiver before integrating it into a single-supply RS-232 design.
ADM209AR - 120kbps +5V RS-232 Transceiver | Analog Devices
The Analog Devices ADM209AR is a high-speed, +5 V powered CMOS RS-232 driver/receiver transceiver with a 120 kbps data rate, 0.1 µF charge-pump capacitors, and a 24-SOIC package. The device provides two RS-232 drivers and two receivers, supports shutdown operation, and is specified for a maximum receiver input range of 30 V. Its CMOS implementation is intended for low-power, high-speed serial-interface designs. An RS-232 transceiver is an interface integrated circuit that combines differential line drivers and receivers with charge-pump circuitry to generate the positive and negative voltage swings required by the RS-232 standard. It belongs to the broader class of interface ICs, connecting a host, peripheral, instrument, or industrial controller to a physical communication port. The ADM209AR is therefore positioned between low-voltage digital logic and an external RS-232 cable. Key features include operation from a +5 V supply, support for 120 kbps data rates, use of only 0.1 µF capacitors, 9 V output swing with a +5 V supply, low power consumption of 15 mW, and active receiver behavior during shutdown for the ADM213 family context identified in the retrieved data. The device also includes latch-up protection and is described as a plug-in upgrade for MAX205, MAX211, and MAX213 devices. The ADM209AR uses charge-pump-generated rails to provide RS-232-compatible output levels from a single positive supply. This architecture simplifies external power design compared with a dual-supply implementation, while the 30 V receiver input rating helps the interface withstand harsher cable-side transients. The 24-SOIC package provides a conventional surface-mount footprint and room for the required external capacitors. Typical applications include RS-232 ports in industrial equipment, test and measurement instruments, computer peripherals, embedded systems, and communications equipment. The 120 kbps rate is suitable for legacy serial links that require higher throughput than slow modem-style interfaces but do not demand modern high-speed differential signaling. When laying out the ADM209AR, place the charge-pump capacitors and RS-232 line-side protection or termination components close to the IC and connector. Verify that the external capacitor polarity, supply decoupling, cable length, and logic levels satisfy the system requirements. Do not substitute a receiver-only or driver-only IC unless the surrounding circuit is redesigned. This product data synthesizes the retrieved manufacturer and distributor information, available pricing, package details, application guidance, and replacement constraints into an engineering-oriented component reference.
ADM209ARS - 200kbps 5V RS-232 Transceiver | Analog Devices
The Analog Devices ADM209ARS is a +5 V CMOS RS-232 interface transceiver with 3 drivers, 5 receivers, 200 kbps data rate, and a 24-lead SOIC package. It uses 0.1 µF charge-pump capacitors, provides 9 V output swing from a 5 V supply, accepts receiver inputs up to 30 V, and includes an enable control for low-power shutdown. The manufacturer identifies the ADM209 family as obsolete, so new production availability should be confirmed before committing a design. A CMOS RS-232 transceiver is an interface IC that translates logic-level signals between a host or controller and RS-232-compatible equipment. In the hierarchy of electronic components, it belongs to interface ICs, within the broader semiconductor category. The driver channels convert TTL/CMOS logic into RS-232 levels, while the receiver channels convert RS-232 inputs back into logic levels. This allows equipment operating at different logic and voltage domains to communicate over a wired serial interface. The ADM209ARS provides five receiver channels and three driver channels, making it useful where a design has more incoming data paths than outgoing data paths. Its 200 kbps maximum data rate supports moderate-speed serial links, while the 0.1 µF charge-pump capacitor requirement reduces external capacitance compared with earlier RS-232 implementations. The 30 V receiver input rating provides additional tolerance for exposed or industrial serial connections, although the complete interface still requires suitable protection in harsh environments. Internally, the device combines CMOS drivers and receivers with on-board charge-pump circuitry. The charge pump generates the RS-232 voltage levels required by the drivers, while the enable pin supports shutdown operation that can reduce system power consumption. Because the part is specified for a single +5 V supply, the ADM209ARS simplifies system power architecture compared with dual-supply RS-232 transceivers. Its 24-lead SOIC package supports conventional surface-mount assembly and is the relevant footprint constraint when evaluating replacements. Typical uses include industrial serial controllers, test equipment, point-of-sale systems, data-acquisition equipment, and embedded systems that need multiple RS-232 receive paths. A 3-transmitter design can connect several peripherals while five receiver inputs can monitor commands, status signals, or acknowledgments. In cable-based installations, designers should also consider ground reference, electrostatic discharge, surge, and isolation requirements that are outside the IC itself. For replacement work, verify the complete 24-pin signal map, supply voltage, channel counts, charge-pump capacitor values, enable polarity, and receiver thresholds rather than relying only on the RS-232 protocol label. The page distinguishes documented cross-reference candidates from a manufacturer-confirmed universal replacement and marks unavailable technical and commercial fields where the retrieved sources do not provide verified values. This page consolidates the retrieved Analog Devices product information, distributor availability, RS-232 application context, package constraints, and cross-reference guidance. It adds design-oriented selection criteria that are useful beyond the basic manufacturer description while clearly separating verified facts from information that still requires engineering confirmation.
ADM211AR - 4/5 RS-232 Transceiver, 120 kbps | Analog Devices
The Analog Devices ADM211AR is a 4-driver, 5-receiver RS-232 transceiver designed for EIA-232-E and V.28 communications from a single 5 V supply. It supports data rates up to 120 kbps, uses 0.1 µF charge-pump capacitors, and provides approximately ±9 V output swing in a 28-pin SOIC package. The integrated dc-to-dc converters eliminate the need for a separate ±12 V supply. An RS-232 transceiver is an interface IC that converts between digital logic levels and the bipolar voltage levels used by RS-232 links. It belongs to the broader line-driver/receiver and interface-IC hierarchy, where differential or single-ended digital signals must cross systems with different voltage references. The ADM211AR combines four transmit channels and five receive channels for multi-port equipment, industrial controllers, and legacy peripheral connections. Key features include four drivers, five receivers, operation from a 4.5 V to 5.5 V supply, and a data rate of 120 kB/s. The on-board dc-to-dc converters support approximately ±9 V output swing from a 5 V supply, while the low-power mode is specified at 15 mW. The receiver section provides 30 V input-level handling according to the supplied search data, making the device useful where protected or long RS-232 lines are encountered. The ADM211AR is designed for EIA-232-E and V.28 interfaces when ±12 V is unavailable. Its 28-SOIC package provides a conventional surface-mount footprint and allows the four transmitters and five receivers to be consolidated instead of using separate interface devices. The exact pin assignments, absolute maximum ratings, propagation timing, and detailed electrical limits must be confirmed in the manufacturer datasheet before layout or production use. Typical applications include RS-232 port expansion, industrial data acquisition, test equipment, instrumentation, and embedded serial interfaces. In a multi-port design, the four drivers can support outgoing connections while five receivers provide additional inbound channels. The shared supply architecture also simplifies system design where a single 5 V rail is available. A key design consideration is maintaining the correct charge-pump capacitor values and checking the RS-232 line polarity and signal levels during bring-up. Decoupling should follow the manufacturer application guidance, and unused channels should be configured according to the datasheet rather than left floating. The device is a digital interface IC, so SOA is not applicable. This product page consolidates verified manufacturer and distributor information, application guidance, sourcing context, and engineering design notes. It distinguishes verified facts from parameters that still require the complete manufacturer datasheet, helping engineers evaluate the ADM211AR without relying on unverified substitutions.
ADM211ARSZ - 4/5 RS-232 Transceiver, 5V, 200kbps | Analog Devices
The Analog Devices ADM211ARSZ is a 5 V CMOS RS-232 transceiver with four drivers and five receivers, a 200 kbps data rate, and a 28-pin SSOP package. It is designed for EIA-232-E and V.28 communication interfaces that require bipolar RS-232 levels but do not have ±12 V supplies available. The device uses charge-pump technology to generate the required voltage swings from a single 5 V power source. An RS-232 transceiver is an interface IC that combines differential line-driver and receiver functions for serial data links. It belongs to the communications-interface hierarchy, where a transceiver converts logic-level signals into RS-232 electrical levels and reconstructs logic-level data from received RS-232 signals. The ADM211 family is particularly useful when system power constraints make traditional ±12 V RS-232 implementations impractical. The ADM211ARSZ provides four driver channels and five receiver channels, allowing several serial ports or multiple control lines to share one package. Its stated 200 kbps maximum signaling rate supports conventional RS-232 links used by instrumentation, industrial equipment, data acquisition systems, and legacy computer peripherals. The 5 V supply architecture eliminates the need for a separate ±12 V rail, reducing board area and power-supply complexity. Its CMOS implementation integrates the charge-pump circuitry required to generate positive and negative RS-232 voltage levels from one supply. The Analog Devices ADM211 family also supports systems where ±12 V is unavailable. Because RS-232 is a point-to-point interface, designers should still account for cable length, ground offset, termination, protection, and transient conditions when laying out the interface. Typical uses include multi-channel serial connectivity in industrial controllers, test and measurement equipment, point-of-sale terminals, printers, scanners, and embedded systems upgrading legacy RS-232 ports. The five receivers provide additional channels for handshake, status, or control signals, while the four drivers support as many as four outbound RS-232 connections when the connected devices have compatible signal assignments. PCB implementation requires careful placement of the charge-pump capacitors and interface-protection components. Keep RS-232 driver and receiver traces away from sensitive analog or high-speed digital paths, provide a stable ground reference, and place any external surge-protection devices where they can clamp cable transients before they reach the IC. Confirm the complete pin assignment and voltage ratings in the manufacturer datasheet before routing the PCB. This page combines the manufacturer product information, exact-MPN catalog records, interface characteristics, and replacement analysis into an engineering-focused guide. It also distinguishes true same-footprint replacements from related RS-232 devices that differ in channel count, package, or operating specifications.
ADM211ARZ - 5V 4/5 RS-232 Transceiver | Analog Devices
The Analog Devices ADM211ARZ is a 5 V RS-232 line-driver and receiver interface IC with 4 drivers, 5 receivers, a 200 kbps data rate, and a 28-pin SOIC package. It uses a 0.1 µF charge-pump capacitor to support EIA-232-E and V.28 communications interfaces when conventional ±12 V supplies are unavailable. An RS-232 transceiver is an interface IC that combines differential line drivers and receivers for serial data transmission over single-ended, bipolar signaling connections. The driver converts CMOS logic levels into RS-232 voltage levels, while the receiver converts incoming RS-232 signals back into CMOS-compatible logic. Within the interface hierarchy, the ADM211ARZ belongs to the RS-232 transceiver class, interface IC category, and broader integrated-circuit family. The ADM211ARZ provides four transmit channels and five receive channels in one package. Its 200 kbps maximum signaling rate supports moderately high-speed equipment links, while the integrated on-board DC-to-DC converters generate the bipolar voltage levels required by RS-232 from a single 5 V supply. The 0.1 µF charge-pump capacitor requirement reduces the number of external support components compared with discrete level-shifting designs. The ADM211 family is specified for a 4.5 V to 5.5 V supply range, with an on-board converter capable of producing approximately ±9 V output swing from the 5 V supply. This architecture allows operation without external ±12 V rails. The device is identified as a low-power RS-232 solution and is suited to portable, industrial-control, instrumentation, and embedded equipment interfaces where supply constraints and channel count are important. Typical uses include multi-channel serial-port connections, industrial data-acquisition equipment, test and measurement systems, and embedded control systems. A four-driver configuration can support four outbound channels, while the fifth receiver can monitor an additional incoming signal. This asymmetry is useful in systems where one node transmits on several lines but receives status, acknowledgment, or data from one additional line. PCB design should preserve short return paths for the RS-232 cable-side pins and provide an uninterrupted ground reference. Place the 0.1 µF charge-pump capacitor close to the device and follow the datasheet connection diagram. RS-232 interfaces also require careful segregation between cable-side and logic-side nets to avoid electrostatic-discharge events propagating into surrounding circuitry. This product page combines the manufacturer device information with package, application, pricing workflow, replacement, and design guidance. It also distinguishes a true same-footprint replacement from alternatives that require a different package or a different channel configuration, helping engineers make a board-level selection without relying on a generic substitute list.
ADM211EARS - 4/5 RS-232 Transceiver, 200 kbps | Analog Devices
The Analog Devices ADM211EARS is a 4-driver, 5-receiver RS-232 interface transceiver operating from a single +5 V supply in a 28-lead SSOP package. It supports data rates up to 200 kbps and is designed for EIA-232-E and CCITT V.28 communications interfaces. The device includes a 0.1 µF charge-pump capacitor capability, low-power shutdown support, and ±15 kV ESD protection on its line-facing pins. An RS-232 transceiver is a bidirectional interface IC that converts logic-level UART signals into RS-232 line levels and converts received RS-232 levels back into CMOS-compatible logic. The ADM211EARS belongs to the broader hierarchy of RS-232 interface transceivers, line drivers, line receivers, and communications interface ICs. Its multi-channel arrangement allows one package to carry four outgoing data channels and five incoming channels, reducing the component count in multi-port equipment. Key features include four drivers, five receivers, operation from a single 5 V rail, and data rates up to 200 kbps. The shutdown control disables the charge pump, transmitters, and receivers, allowing the interface to reduce power consumption when communication is inactive. Analog Devices identifies the family as conforming to the EIA-232-E and CCITT V.28 specifications and as suitable for environments where a 12 V supply is unavailable. The ADM211EARS uses the ADM2xxE interface architecture for robust point-to-point RS-232 links. Its line-facing protection is specified at ±15 kV ESD, making it applicable to equipment whose serial ports may be connected externally or through long cable runs. The interface operates from 5 V, allowing it to share a common supply rail with CMOS logic in many embedded and industrial control systems. Typical uses include industrial serial controllers, point-of-sale terminals, test equipment, data acquisition systems, and multi-channel RS-232 port expansion. The four drivers and five receivers make the part especially useful where a system has more peripheral serial links than a single UART can support. Because the part is obsolete, new designs should verify availability and consider a listed parametric equivalent before committing a new design to this exact suffix. For layout, route each RS-232 line directly to its corresponding connector-side network and place the specified 0.1 µF charge-pump capacitor close to the device. Keep logic-side traces away from cable-side inputs, and confirm the shutdown-control polarity and timing against the ADM211E datasheet before enabling the interface in firmware. This page consolidates the ADM211EARS lifecycle position, verified equivalent candidates, package information, interface parameters, and practical integration guidance so engineers can evaluate an obsolete 28-SSOP transceiver without repeating the same cross-reference work.
ADM211EARSZ - 5V 4/5 RS-232 Transceiver | Analog Devices
The Analog Devices ADM211EARSZ is a single-supply RS-232 line-driver and receiver transceiver with four drivers, five receivers, a 4.5 V to 5.5 V supply range, and operation up to 230 kbps. It is packaged in a 28-pin SSOP and provides ±15 kV electrostatic-discharge protection for interfaces exposed to industrial and commercial cabling environments. An RS-232 transceiver is an interface IC that converts logic-level signals into balanced, single-ended RS-232 line levels and converts received line signals back into CMOS-compatible logic. It belongs to the interface IC hierarchy, where transceivers combine line drivers and receivers in one package. The ADM211 family supports EIA-232E and CCITT V.28 signaling while reducing the number of separate components required for multi-channel serial links. The device includes four transmit channels and five receive channels, allowing a design to support several unidirectional or bidirectional RS-232 connections. Its single 5 V supply architecture simplifies power sequencing and works with contemporary CMOS logic. External supply bypassing is specified at 0.1 µF, while the charge-pump and driver arrangement provides the bipolar voltage levels required by RS-232 without a separate bipolar supply. The ADM211E family is designed for harsh electrical environments and provides EMI/EMC-focused protection. Published system information identifies conformance with the EIA-232E and CCITT V.28 specifications, data rates up to 230 kbps, and enhanced ESD protection relative to earlier ADM211 variants. These characteristics are particularly useful where cables leave an enclosure and may be exposed to electrostatic discharge, conducted noise, or long interconnects. Typical uses include industrial serial controllers, instrumentation links, point-of-sale equipment, test and measurement systems, and embedded data-acquisition equipment. The five receiver channels can handle data, control, status, or handshake signals, while the four driver channels support outbound data and control paths. The extra receiver is useful for monitoring an incoming source or implementing a bus arrangement with one shared line and several local receivers. PCB design should preserve the manufacturer’s recommended charge-pump capacitor connections and place the 0.1 µF supply capacitor close to the device. RS-232 driver outputs must not be confused with TTL or CMOS outputs, and unused channels require appropriate termination according to the interface circuit. Verify signal polarity, direction, and receiver enable behavior against the ADM211E pin description before releasing a production layout. This product page combines the manufacturer’s family-level specifications with exact package and ordering information for ADM211EARSZ, structured drop-in comparisons, practical interface-layout guidance, and searchable RS-232 design information. It is intended to help engineers identify the correct channel count, package, protection level, and replacement before beginning PCB implementation.
ADM211EARU - 4/5 RS-232 Transceiver | Analog Devices
The Analog Devices ADM211EARU is a single-chip RS-232 transceiver with four line drivers, five line receivers, and 200 kbps operation in a 28-lead TSSOP package. It operates from a single 5 V supply and uses a 0.1 µF charge-pump capacitor for its RS-232 interface voltage generation. The integrated 4/5 transceiver configuration makes the device suitable for equipment that drives several RS-232 channels while receiving data from five channels. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts received line-level signals back into CMOS-compatible logic. It belongs to the interface IC hierarchy, alongside UART and communications transceivers, and provides the physical signaling layer between digital equipment and a serial port. ADM211EARU supports the RS-232 and V.28 interface requirements associated with single-ended, point-to-point serial connections. The four-driver and five-receiver arrangement is the principal feature of the ADM211 family. Its maximum signaling rate of 200 kbps supports conventional RS-232 equipment, industrial control links, instrumentation, and data-acquisition systems. Operation from one 5 V rail simplifies system power design, while the 0.1 µF charge-pump capacitor avoids the external supply requirements associated with older bipolar RS-232 implementations. The Analog Devices product documentation describes the ADM211 as a production device with EMI/EMC-compliant interface circuitry and ±15 kV ESD protection. These characteristics are especially valuable when the connector is exposed to user-accessible cables, industrial cabinets, or electrically noisy equipment. The 28-lead TSSOP package provides a compact surface-mount footprint while exposing individual driver outputs, receiver inputs, ground, supply, and charge-pump functions for direct PCB routing. Typical uses include industrial serial controllers, test and measurement equipment, POS terminals, communications adapters, and embedded systems that retain legacy RS-232 ports. Because the device provides more drivers than receivers, it is particularly useful for multiport designs with several outbound modem-style signals and fewer inbound signals. It can also serve systems requiring unidirectional RS-232 outputs alongside independent receive channels. PCB layout should keep the RS-232 traces short and route them away from clocks, switching regulators, and high-current return paths. Connect the specified 0.1 µF charge-pump capacitor close to its dedicated capacitor pin, provide a low-impedance ground connection, and place protection components near the external connector. ESD protection helps the interface, but cable transients should still be evaluated at the system boundary. This product page combines the ADM211 family characteristics, package information, sourcing paths, interface guidance, and replacement evaluation criteria. It also distinguishes the exact ADM211EARU ordering code from reel and tape-and-reel suffix variants so engineers can maintain the correct 28-lead TSSOP footprint and BOM intent.
ADM211EARZ - 4/5 RS-232 Transceiver | Analog Devices
The Analog Devices ADM211EARZ is a 4-driver, 5-receiver RS-232 transceiver designed for single 5 V operation, with a 200 kbps maximum data rate and a 28-pin SOIC package. It supports bidirectional serial communication through four line drivers and five line receivers, providing more receiver channels than drivers for equipment that must monitor multiple remote RS-232 ports. The device uses 0.1 µF charge-pump capacitors and is intended for EIA-232-E and CCITT V.28 interfaces. An RS-232 transceiver is an interface IC that converts between complementary logic-level signals and the voltage levels used on RS-232 links. It belongs to the transceiver category within interface ICs and ultimately serves as a physical-layer link between digital equipment and a serial port. The ADM211EARZ is useful when a system needs several RS-232 channels without using a separate driver or receiver IC for every port. Key features include four transmit channels, five receive channels, operation from a single 5 V supply, and data-rate capability up to 200 kbps. The manufacturer describes the part as a robust interface for applications where 12 V is unavailable. Its 28-pin SOIC package provides a conventional surface-mount form factor, while separate driver outputs and receiver inputs allow several communication paths to be implemented in one device. The ADM211EARZ uses an on-chip charge pump to generate the positive and negative voltages required by RS-232 line drivers. The 0.1 µF external capacitor specification reflects the charge-pump implementation rather than a requirement for 0.1 µF bypass capacitors on every supply rail. Designers should follow the manufacturer’s recommended connection and decoupling arrangement to preserve signal integrity and achieve the specified data rate. Typical uses include industrial serial controllers, test equipment, data-acquisition systems, point-of-sale equipment, embedded serial-port controllers, and instrumentation that must communicate with legacy RS-232 peripherals. The five receivers are particularly useful in systems where several incoming links must be sensed while only four outbound links are required. A transceiver remains necessary when the system lacks RS-232 electrical-level drivers or receivers on its controller. A key design consideration is that the ADM211EARZ is a multi-channel RS-232 interface, not a modern USB-to-serial converter. Existing point-to-point RS-232 cabling, signal polarity, grounding, and software drivers must be considered before replacing a legacy port. The system should also account for ground differences between connected equipment and use suitable protection when exposed to industrial transients. This product page consolidates the manufacturer’s RS-232 interface information, verified distributor listings, drop-in cross-reference findings, and practical implementation guidance. It helps engineers distinguish true pin-compatible replacements from packaging-only variants while focusing on channel count, supply voltage, data rate, and the shared 28-pin SOIC footprint.
ADM213AR - 4/5 5V RS-232 Transceiver, 200kbps | Analog Devices
The Analog Devices ADM213AR is a production +5 V CMOS RS-232 transceiver with four drivers, five receivers, shutdown and enable pins, and two receivers remaining active during shutdown. It supports data rates to 200 kbps, operates from a 4.5 V to 5.5 V supply, and uses a 28-pin SOIC package. Its integrated DC-to-DC converters produce approximately ±9 V output swing from a single 5 V supply. An RS-232 transceiver is an interface IC that converts logic-level TTL or CMOS signals into RS-232-compatible differential voltage levels, while converting received RS-232 levels back into logic-level signals. The ADM213AR belongs to the line-driver/receiver and interface-IC hierarchy used for EIA-232-E and V.28 communications where ±12 V is unavailable. Integrating charge-pump converters eliminates the need for a separate negative supply in many point-to-point interfaces. Key features include four RS-232 drivers, five receivers, two receivers active in shutdown, 0.1 µF charge-pump capacitors, 120 kbps data-rate support in the cited feature data, and approximately ±9 V output swing with a 5 V supply. The reported low-power figure is 15 mW. The 28-SOIC package is suitable for conventional through-hole PCB assembly, and the device is identified as a plug-in upgrade for MAX205, MAX211, and MAX213 families. The device uses a single positive supply, making it useful for systems that cannot easily provide negative RS-232 rails. Its receiver inputs are specified for ±30 V input levels, while latch-up protection is listed as a feature. The shutdown function can reduce system power when the interface is inactive, although two receivers remain operational for selected monitoring or wake-up signals. Typical applications include industrial RS-232 links, instrumentation, point-of-sale equipment, data acquisition systems, embedded serial ports, and legacy computer peripherals. When using the device, verify the exact pinout, shutdown polarity, receiver enable behavior, charge-pump capacitor values, and RS-232 signal polarity against the manufacturer datasheet before final PCB release. This page combines the supplied manufacturer and distributor information, sourcing links, interface context, and engineering cautions. Pricing and cross-reference claims are limited to the retrieved data; unverified values are marked as data needed rather than guessed.
ADM213ARS - 4/5 RS-232 Transceiver | Analog Devices
Analog Devices ADM213ARS is a +5 V powered CMOS RS-232 transceiver with four drivers, five receivers, shutdown and enable controls, and onboard DC-to-DC conversion, packaged in a 28-lead SSOP. The device supports 200 kBPS operation according to the manufacturer product page and provides 0.1 µF charge-pump capacitor operation. Its integrated converter produces approximately ±9 V output swing from a single +5 V supply, allowing RS-232 interfaces to operate without external ±12 V rails. An RS-232 transceiver is an interface IC that converts between TTL-compatible logic levels and the bipolar voltage levels used by RS-232 equipment. Its driver channels translate logic states into RS-232 output signals, while its receiver channels translate RS-232 inputs into digital logic. Positioned within the interface-IC hierarchy, this combined transceiver provides the physical signaling layer between data-processing equipment and serial-port peripherals. The ADM213 combines four driver channels with five receiver channels, making it appropriate for equipment that requires one more receive channel than transmit channel. Two receiver channels remain active during shutdown according to the ADM213 family information, allowing selected incoming signals to be monitored while the main interface operates at reduced power. Separate shutdown and enable pins support controlled operating-state transitions in equipment with managed power rails. Its CMOS implementation integrates the power-conversion function needed to generate RS-232-level voltage swings from +5 V. The manufacturer describes low-power operation at 15 mW and a low-power shutdown state below 5 µW. The ADM213 family is also identified as latch-up free and supports receiver input levels extending to 30 V, improving tolerance of connected RS-232 signals. A maximum data rate of 120 kB/s is listed in the ADM213 feature summary, while the official product page describes the family as supporting 200 kBPS. Typical uses include industrial serial-port adapters, data-acquisition equipment, test systems, barcode-reader interfaces, and embedded serial controllers that cannot provide ±12 V. In these systems, the integrated converter reduces external power-supply complexity, while the shutdown function can reduce consumption when the interface is idle. The enable and shutdown inputs can also support coordinated behavior with system power-management circuitry. Designers should follow the manufacturer's pin-description table when assigning PCB tracks and connect the external charge-pump capacitor at the specified pins. Maintain the required supply decoupling close to VCC and GND, and route driver outputs and receiver inputs away from sensitive analog circuitry. Confirm that the selected cable length, baud rate, logic levels, and shutdown behavior satisfy the system interface requirements. This page combines the manufacturer's product information with same-footprint upgrade options, application guidance, and design notes intended to make RS-232 hardware decisions more systematic. It highlights the ADM213ARS channel count, supply architecture, power-control features, and package constraints without treating a simple electrical equivalence as proof of complete system compatibility.
ADM213ARSZ - 200kbps RS-232 Transceiver | Analog Devices
The Analog Devices ADM213ARSZ is a 5 V powered CMOS RS-232 transceiver with four drivers, five receivers, shutdown and enable pins, and two receivers active during shutdown. It supports data rates up to 200 kbps and operates from a single 5 V supply while producing approximately ±9 V transmitter output swings through its on-board DC-to-DC converters. The device is packaged in a 28-pin SSOP. An RS-232 transceiver is an interface integrated circuit that combines differential line drivers and receivers for serial data communication. It belongs to the EIA-232-E and V.28 interface hierarchy, translating between CMOS logic levels and the voltage levels used by RS-232 links. The ADM2xx family is intended for equipment where conventional ±12 V supplies are unavailable, making a single 5 V rail practical for modern embedded systems. Key features include operation with external capacitors from 0.1 µF to 10 µF, a maximum data rate of 200 kbps, low-power shutdown, and receiver operation to ±30 V. Two receivers remain active in shutdown, allowing selected incoming signals to be monitored without keeping every receiver active. The integrated charge-pump converters provide approximately ±9 V transmitter swings, reducing the need for external negative-voltage generation. The ADM213 combines four transmit channels with five receive channels in one package. Its shutdown and enable controls support systems that need to reduce power consumption when a serial link is inactive. The two shutdown-active receivers are especially useful where a modem, industrial terminal, or data acquisition system must detect an incoming activity or control indication while the main interface is powered down. Typical uses include industrial serial consoles, instrumentation, point-of-sale equipment, security systems, test systems, and embedded control boards. The ±30 V receiver tolerance provides protection against higher-voltage RS-232 sources, while the integrated converters allow operation from a single 5 V supply. Designers should still protect the physical interface against surge, ESD, and cable transients according to the application environment. The main design consideration is charge-pump capacitor selection. The ADM213 supports a broad external-capacitor range, but the selected capacitors, wiring, and voltage ratings must satisfy the Analog Devices datasheet requirements. Place the charge-pump and interface capacitors close to their associated pins, preserve a continuous ground return, and validate the implemented layout against the manufacturer's application guidance. This technical overview combines the device's interface architecture, shutdown behavior, package constraints, and practical RS-232 design considerations into an engineering-focused guide. It also identifies pin-compatible alternatives and highlights the parameter checks required before replacing an existing ADM213ARSZ in production equipment.
ADM213ARZ - 4/5 RS-232 Transceiver, 200 kbps | Analog Devices
The Analog Devices ADM213ARZ is a four-driver, five-receiver RS-232 transceiver rated for data rates up to 200 kbps and operation from a 5 V supply. The device is packaged in a 28-pin SOIC and accepts 0.1 µF charge-pump capacitors. It includes on-board dc-to-dc converters that produce approximately ±9 V output swings from the single 5 V supply. An RS-232 transceiver is an interface IC that combines differential line drivers and receivers into a circuit capable of communicating with equipment using the EIA-232-E and V.28 physical-layer standards. The ADM213ARZ belongs to the broader hierarchy of interface ICs, communication transceivers, and semiconductors. It is intended for systems that cannot provide external ±12 V rails but still require compliant RS-232 signal levels. The ADM213ARZ provides four transmit drivers and five receive channels, allowing one board to support multiple serial links. Its shutdown and enable controls support power management in equipment where inactive interface circuitry must not consume unnecessary power. Two receivers remain active during shutdown, enabling selected data paths to remain monitored. The 200 kbps capability is suitable for legacy serial equipment, industrial control links, service interfaces, and instrumentation. The integrated charge-pump circuitry simplifies implementation compared with an RS-232 solution requiring external negative-voltage generation. The 4.5 V to 5.5 V operating range supports conventional 5 V system rails, while the approximately ±9 V charge-pump outputs provide the voltage swing needed to overcome RS-232 receiver thresholds. Use the manufacturer datasheet for the recommended capacitor values, driver and receiver electrical limits, enable polarity, and complete timing characteristics. Typical applications include multi-port industrial control panels, configuration and programming ports, laboratory equipment, point-of-sale systems, and embedded systems communicating with legacy RS-232 peripherals. Multiple drivers permit several output ports, while five receivers provide additional channels for status, handshake, and incoming data signals. The shutdown function is particularly useful in portable or space-constrained systems where unused channels must be disabled. PCB implementation should follow the manufacturer datasheet layout for the charge-pump capacitors and high-voltage RS-232 pins. Keep sensitive receiver traces away from driver outputs and switching-capacitor nodes, use the specified ceramic capacitor types, and provide adequate ground return paths. Confirm pin functions, shutdown behavior, and enable polarity against the current datasheet before assigning control signals. This product page combines the ADM213ARZ specifications, package information, sourcing guidance, comparison points, and practical interface-design considerations. It also identifies verified same-footprint replacement candidates while clearly distinguishing them from parts that require different packages or revised circuitry.
ADM213EAR - 4/5 RS-232 Transceiver | Analog Devices
Analog Devices ADM213EAR is a single-supply RS-232 and V.28 interface transceiver with four drivers, five receivers, shutdown and enable pins, and two receivers active during shutdown. The device operates from a single 5 V supply and supports data rates up to 230 kbps according to the manufacturer product information. It is packaged in a 28-pin SOIC. An RS-232 transceiver is an interface IC that translates between TTL/CMOS logic levels and the bipolar voltage levels used by RS-232 communication links. The ADM2xxE family provides integrated drivers and receivers, allowing a complete multi-channel RS-232 port to be implemented with fewer external components. The ADM213EAR combines four transmit channels with five receive channels and includes control functions for systems that need to reduce power or preserve selected receive paths during shutdown. Key features include four RS-232 drivers, five RS-232 receivers, a maximum data rate of 230 kbps, single +5 V operation, and shutdown and enable control pins. The manufacturer describes the ADM2xxE devices as robust RS-232 and V.28 interface devices that fully conform to EIA-232E and CCITT V.28 specifications. The shutdown arrangement allows two receivers to remain active, which is useful in systems that need to monitor communication or wake from a low-power state. The ADM213EAR is suitable for industrial automation, instrumentation, data acquisition, telecommunications, and embedded control systems that use RS-232 ports. Its integrated multi-channel design reduces board area and simplifies firmware handling compared with separate line-driver and receiver packages. The enable and shutdown controls provide additional flexibility for power management and peripheral sharing. When designing around the ADM213EAR, check every unused driver and receiver input so that no floating input can create unnecessary current or data errors. Place the interface IC close to the connector and route each RS-232 line away from sensitive analog and clock signals. Decoupling capacitors should be placed at the supply pins according to the manufacturer datasheet, and the ground connection should follow the interface layout recommendations. This page combines the Analog Devices product description, distributor package information, technical application guidance, verified specifications, and replacement considerations for engineers evaluating the ADM213EAR.
ADM213EARS - 5V 4/5 RS-232 Transceiver | Analog Devices
The Analog Devices ADM213EARS is a 4-driver, 5-receiver RS-232 transceiver designed for single 5 V supply operation in a 28-pin SSOP package. It supports data rates up to 230 kbps, provides shutdown and enable control functions, and keeps two receivers active during shutdown. The device is intended for EIA-232E and CCITT V.28 communications interfaces where conventional ±12 V RS-232 levels must be generated from a low-voltage supply. An RS-232 transceiver is an interface IC that combines line drivers and line receivers on one chip. The drivers convert low-voltage logic signals into RS-232-compatible levels, while the receivers convert bipolar RS-232 signals into logic-compatible outputs. The ADM213E belongs to the broader hierarchy of RS-232 interface transceiver, communications interface IC, interface IC, and semiconductor product categories. Key features include four transmit drivers, five receive channels, data-rate operation up to 230 kbps, and a 0.1 µF charge-pump capacitor. Shutdown control reduces power consumption when the interface is inactive, while enable control supports individual transmitter operation. The ADM213E family is designed for harsh electrical environments and includes electrostatic-discharge protection as described by Analog Devices. The device uses a CMOS-compatible 5 V architecture and on-chip charge-pump circuitry to generate the positive and negative voltage levels required by RS-232 transmitters. Only one 0.1 µF capacitor is required for charge-pump operation according to the ADM213 product description. Two receiver channels remain active during shutdown, allowing selected incoming signals to be monitored without keeping every transmitter and receiver enabled. Typical applications include industrial serial-port interfaces, instrumentation, data-acquisition equipment, point-of-sale terminals, and embedded control systems. The four-driver configuration supports multiple outbound channels, while five receivers support inbound status, handshake, and data signals. In systems using RS-232 only for legacy peripheral connectivity, the single 5 V supply simplifies interface design compared with discrete ±12 V driver circuits. PCB implementation requires careful placement of the charge-pump capacitor and protection-network connections. Follow the pin-description table and application circuit in the manufacturer datasheet when assigning tracks, and keep interface and logic return paths appropriately separated to minimize common-mode noise. Confirm that cable length and baud rate remain within the limits specified for the selected EIA-232 or CCITT V.28 operating mode. This product page consolidates the ADM213E family architecture, package information, verified interface ratings, application guidance, comparison data, and design considerations into a design-oriented reference. It helps engineers distinguish supply, shutdown, enable, channel-count, and package considerations before selecting an RS-232 transceiver for a new board.