LM2902VDTBG - Quad 3-26V Op Amp | onsemi | Industrial
Teilenummer: LM2902VDTBG ✓ AktivLM2902VDTBG Übersicht
An operational amplifier is an active analog component that uses high-gain differential feedback to amplify the voltage difference between its two inputs. The quad LM2902 configuration integrates four amplifiers into one package, reducing board area when a system requires several independent signal-conditioning channels. In the signal-chain hierarchy, the LM2902 belongs to the operational-amplifier family, which is part of analog signal-chain ICs and ultimately semiconductor devices used for measurement, control, conversion, and buffering.
The LM2902 series provides four general-purpose amplifier sections in one device. According to onsemi’s LM2902 documentation, the series supports operation from low-voltage single-supply systems to higher-voltage supplies. The Mouser listing identifies the LM2902VDTBG as a 3 V to 26 V, low-power, extended-temperature quad amplifier. A GlobalSpec result identifies the device as a bipolar quad operational amplifier with a maximum input offset voltage of 7000 uV, while the DigiKey listing characterizes it as a standard general-purpose amplifier.
Each amplifier section includes non-inverting and inverting inputs and an output, allowing the device to support voltage followers, noninverting amplifiers, inverting amplifiers, summing circuits, comparators, and differential signal conditioning. Because four amplifiers share one package, engineers can allocate them across related channels such as a sensor input, its reference, an output driver, and an auxiliary monitor. Exact input-offset, input-bias-current, gain-bandwidth, slew-rate, output-current, and noise figures should be selected from the operating conditions in the onsemi datasheet before committing a high-accuracy design.
Typical uses include industrial transducers, temperature and pressure sensor interfaces, low-level signal amplification, control-system signal conditioning, audio preamplification, and general-purpose buffering. Its quad organization is particularly useful when a board needs several similar analog channels without allocating separate packages for each amplifier. The 14-pin TSSOP footprint also supports compact surface-mount layouts, although pin pitch and exposed thermal behavior remain important layout considerations.
When designing around the LM2902VDTBG, begin with the four complete amplifier sections and confirm the required input common-mode range, output swing, supply current, noise, and stability behavior at the intended supply voltage. Decoupling capacitors should be placed close to the supply pins, and sensitive input traces should be routed away from switching nodes. Because the exact electrical limits are governed by the manufacturer datasheet, verify the operating temperature, package dimensions, pin orientation, and gain-bandwidth requirements against the final circuit and PCB constraints.
This product record organizes the manufacturer and distributor information for LM2902VDTBG with practical guidance for signal-chain design, source selection, and footprint verification. It also identifies the limits of the available replacement information so that engineers can distinguish confirmed package compatibility from merely similar amplifier families.
Drop-in-Alternativen für LM2902VDTBG – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit LM2902VDTBG (gleiche Bauform und Footprint) – abweichend in Number of Channels, Package, Power Class.
Für dieses Produkt sind keine Drop-in-Alternativen verfügbar.
Alternativen anfordernLM2902VDTBG Grenzwerte & elektrische Eigenschaften
| Amplifier Count | 4 amplifiers |
| Device Type | Standard general-purpose operational amplifier |
| Supply Voltage Range | 3 V to 26 V |
| Architecture | Bipolar operational amplifier |
| Maximum Input Offset Voltage | 7000 uV |
| Betriebstemperatur | Extended temperature |
| Power Class | Low-power operational amplifier |
| Gehäuse | 14-pin TSSOP |
| Package Designation | PDSO14 |
| Montageart | Surface mount |
| Input Type | Differential input |
| Number of Channels | 4 channels |
LM2902VDTBG pdso14 Pinbelegungsleitfaden
Pinbelegung für LM2902VDTBG (pdso14-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.
Keine detaillierten Pinbelegungsdaten verfügbar für LM2902VDTBG.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
LM2902VDTBG ist geeignet für 6 Anwendungs: Industrial Sensor Signal Conditioning, Temperature and Pressure Transducer Interface, Control-System Analog Front End, Low-Level Audio Preamplification, Data Acquisition and Instrumentation, Power-Supply Monitoring and Control.
Industrial Sensor Signal Conditioning
The LM2902VDTBG suits multichannel industrial sensor-conditioning designs because it combines four general-purpose amplifier sections with a 3 V to 26 V supply range and extended-temperature capability. Two channels can amplify and filter a differential sensor signal, while the remaining channels can buffer a reference or monitor another sensor. The integrated quad arrangement reduces package count and simplifies power routing, although the final design must confirm the input common-mode range, output swing, offset behavior, and bandwidth against the manufacturer electrical tables. The 14-pin TSSOP should be placed so that sensitive input nodes remain away from switching regulators and high-current return paths.
Empfohlen
Temperature and Pressure Transducer Interface
The LM2902VDTBG can form the analog front end for resistance-based temperature or pressure transducers. One amplifier channel can provide excitation buffering, another can amplify the resulting differential voltage, and the final channels can implement gain or reference stages. Its low-power quad architecture is useful when several related sensors share a board and require a common supply arrangement. The designer should verify that excitation amplitude and sensor output remain within the input common-mode range, and that offset and drift satisfy the measurement resolution. Decoupling capacitors should be placed near the supply pins with a short, low-impedance return path.
Empfohlen
Control-System Analog Front End
In a control-system analog front end, the LM2902VDTBG can amplify error signals, buffer command voltages, and support auxiliary feedback channels without requiring four separate amplifier packages. Its 3 V to 26 V operating range is suitable for systems that operate from a single low-voltage rail as well as designs using a higher industrial supply. Practical implementation requires checking the output-drive limits at the chosen load and maintaining the required loop stability with the selected feedback network. Keep sensitive amplifier inputs away from relay coils, power switches, and high-current actuator wiring, and use a quiet ground reference where feedback accuracy is important.
Empfohlen
Low-Level Audio Preamplification
The LM2902VDTBG can provide low-level audio preamplification when four similar gain stages, mixers, or buffers are needed. Its four amplifier sections allow a compact implementation of input amplification, active filtering, and output buffering in a 14-pin TSSOP. The device’s general-purpose architecture supports conventional inverting, noninverting, and summing configurations. Audio performance still depends on the selected gain-bandwidth and noise characteristics for the exact operating point, so the designer should avoid bandwidth or slew-rate limitations at the highest audio frequencies. Use short input traces, decouple the supply near the device, and maintain a low-impedance shared ground to minimize added noise.
Empfohlen
Data Acquisition and Instrumentation
The LM2902VDTBG is appropriate for general instrumentation where several low-level analog channels must be conditioned before sampling or measurement. Four channels can handle differential amplification, impedance buffering, active filtering, and reference conditioning in a compact footprint. The 3 V to 26 V supply range supports both portable low-voltage equipment and higher-voltage industrial instruments, while extended-temperature capability broadens its deployment range. Verify the offset voltage, bias current, gain-bandwidth product, and output behavior under the actual source impedance and temperature. Place the TSSOP close to the connector or source to minimize interference and keep the feedback network physically compact.
Empfohlen
Power-Supply Monitoring and Control
The LM2902VDTBG can monitor a power rail and support threshold, amplification, or error-amplifier functions in a general-purpose control circuit. Its four channels can divide workload among sensing, filtering, feedback, and buffered outputs, while the 3 V to 26 V supply range accommodates a variety of industrial rail levels. The design must ensure that the monitored voltage and amplifier outputs remain within the applicable common-mode and output-swing limits. At higher supply voltages, thermal considerations become more important even though the device is described as low-power. Use short supply traces, local high-frequency bypass, and a defined high-current return path to prevent supply noise from disturbing the monitored signal.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für LM2902VDTBG – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt |
|---|---|
| Brand | onsemi |
| Package | 14-pin TSSOP (PDSO14) |
| Amplifier Count | 4 channels |
| Supply Voltage Range | 3 V to 26 V |
| Architecture | Bipolar |
| Maximum Input Offset Voltage | 7000 uV |
| Power Class | Low power |
| Temperature Capability | Extended temperature |
| Functional Role | Standard general-purpose operational amplifier |
Wichtigste Unterscheidungsmerkmale
- Four amplifiers in one compact package (vs. LM2902KPWR)
- Single-supply operating capability (vs. LM2902VDTBR2G)
- Extended-temperature LM2902 configuration (vs. LM324DTBG)
Designhinweise
Place the input bypass capacitor and the device’s supply pins on the same side of the PCB with a short, low-impedance connection. Connect the decoupling return directly to the appropriate ground plane rather than routing it through the analog-signal ground. For the 14-pin TSSOP, verify the manufacturer land pattern and pin-1 orientation before fabrication because the exposed package geometry and lead pitch must match the selected footprint.
Route each non-inverting and inverting input as a compact differential pair, keep them away from switching nodes, and avoid sharing long traces with high-impedance sensor wiring. Place feedback components close to the associated amplifier pins to minimize parasitic capacitance. When the source impedance is high, verify bias-current error and noise against the onsemi electrical characteristics before choosing the smallest practical feedback resistor.
Do not equate the LM2902 family name with identical package compatibility. LM2902DTBG, LM2902VDTBR2G, LM2902PWRG4, and NCV2902DTBR2G appeared in comparison material, but each order code must be checked for package dimensions, pitch, pin arrangement, temperature grade, and electrical limits. A footprint match alone is insufficient if the replacement lacks the required input common-mode range, output swing, bandwidth, or stability at the circuit’s supply voltage.
Compliance-Informationen
No definitive RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status is stated in the available product information. Confirm these attributes for the exact orderable part with onsemi or the authorized supply channel before regulatory approval.