ATF22LV10CQZ-30JU - 30ns 10-Macrocell EEPLD | Microchip
MPN: ATF22LV10CQZ-30JU ✓ فعالATF22LV10CQZ-30JU نمای کلی
A simple programmable logic device, or SPLD, is a semiconductor that implements fixed Boolean logic through user-programmed fuse or memory elements. In the broader hierarchy, the ATF22LV10CQZ-30JU belongs to programmable logic devices, programmable logic arrays, digital logic ICs, and integrated circuits. Its electrically erasable flash-memory configuration permits reprogramming without a dedicated external programmer.
The principal benefits include 10 macrocells for implementing sum-of-products logic, a 30 ns propagation-delay grade, 10 configurable user I/O pins, and operation from 3.0 V to 5.5 V. The manufacturer identifies the family as supporting speeds down to 25 ns, with each speed grade specified over the full 3.0 V to 5.5 V range. Edge-sensing zero standby power further reduces active supply demand to 3 uA typical when the power-down function is asserted.
ATF22LV10CQZ-30JU combines a 22V10 architecture with electrically erasable flash memory. The 10 macrocells provide dedicated product-term logic and programmable output routing for control, decoding, address translation, interface conditioning, and fixed Boolean functions. Because the device supports both 3.3 V and 5 V supply environments, designers can standardize a board platform across mixed industrial and commercial voltage levels, although each design must retain the required input and output operating constraints.
Typical uses include industrial control logic, data-acquisition interface decoding, display and instrument control, peripheral address decoding, and embedded system glue logic. The ATF22LV10CQZ-30JU is especially useful when a small amount of deterministic Boolean logic is needed but a microcontroller or FPGA would add unnecessary cost, software complexity, or board area. The 28-pin PLCC package also supports legacy industrial boards with through-hole-style J-lead geometry.
Designers should verify every pin assignment in the manufacturer pin-description table before laying out a replacement PCB. Input and output pins are multiplexed through the SPLD architecture, so changing a programmed macrocell or output polarity can alter signal behavior even when the physical package remains unchanged. Power-down, reset, clock, and I/O direction decisions should be made before programming the device.
This product page combines the Microchip family specifications with practical replacement guidance, package-aware comparisons, and design notes for programming, logic partitioning, power behavior, and legacy-system integration. These engineering details help determine whether the ATF22LV10CQZ-30JU can reuse an existing PCB and preserve the intended timing and logic behavior.
جایگزینهای drop-in برای ATF22LV10CQZ-30JU — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای ATF22LV10CQZ-30JU (همان فرمفاکتور و فوتپرینت) — متفاوت در Architecture, Device Type, Logic Family, Package, Power-Down Feature.
ATF22LV10CQZ-30JC
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←ATF22LV10C-10JU
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←ATF22LV10CZ-25JI
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←ATF22LV10CZ-25JC
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←GAL22V10D-7LJI
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
ATF22LV10CQZ-30JU حداکثر مقادیر مجاز و مشخصات الکتریکی
| Device Type | High-performance CMOS electrically erasable programmable logic device |
| Architecture | 22V10 SPLD |
| Macrocells | 10 macrocells |
| User I/O Pins | 10 pins |
| Speed Grade | 30 ns |
| Family Minimum Speed | 25 ns |
| Supply Voltage Range | 3.0 V to 5.5 V |
| Logic Family | CMOS |
| Programmable Technology | Electrically erasable flash memory |
| Power-Down Standby Current | 3 uA typical |
| بستهبندی | 28-pin PLCC, 11.51 mm x 11.51 mm |
| Package Construction | J-lead chip carrier |
| نوع نصب | Surface mount |
| Temperature Grades | Industrial and commercial |
| Datalog and Control | 10 registers |
راهنمای پیکربندی پین ATF22LV10CQZ-30JU j-lead chip carrier
پیکربندی پین برای ATF22LV10CQZ-30JU (پکیج j-lead chip carrier). این IC دیجیتال شامل GPIO، رابطهای ارتباطی (UART، SPI، I2C) و پینهای تغذیه است. برای عملکردهای جایگزین پین و گزینههای پیکربندی به دیتاشیت سازنده مراجعه کنید. ضروری برای طراحی سیستمهای نهفته و چیدمان PCB.
داده پینآوت تفصیلی موجود نیست برای ATF22LV10CQZ-30JU.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
ATF22LV10CQZ-30JU مناسب است برای 6 کاربردs: Industrial Control and Interlock Logic, Data-Acquisition Interface Decoding, Legacy Peripheral Address Decoding, Display and Instrument Control, Power-Sequence and Fault Logic, Embedded System Glue Logic.
Industrial Control and Interlock Logic
The ATF22LV10CQZ-30JU is appropriate for deterministic industrial control functions that combine inputs from switches, sensors, and interlocks into machine-control outputs. Its 10 macrocells and 10 user I/O pins can implement Boolean equations, state decoding, and output conditioning without introducing a microcontroller software task. The 3.0 V to 5.5 V supply range supports both 3.3 V and 5 V control boards. Designers should preserve input-level constraints, account for the 30 ns propagation-delay grade, and validate every I/O mapping in the manufacturer pin table.
پیشنهادی
Data-Acquisition Interface Decoding
The ATF22LV10CQZ-30JU can decode status flags, route acquisition channels, and qualify control signals in a data-acquisition system. Its 10 configurable I/O pins allow address, chip-select, mode, or interrupt logic to be consolidated into a single deterministic device. The electrically erasable flash configuration supports design updates without relying on a one-time fuse program. For a 3.3 V instrumentation platform, operate within the 3.0 V minimum supply and verify setup, hold, and propagation timing against the interface clock rate.
پیشنهادی
Legacy Peripheral Address Decoding
ATF22LV10CQZ-30JU is well suited to selecting memories, transceivers, counters, or data converters in a legacy peripheral bus. Ten macrocells provide enough product-term capacity for multiple address and command decode paths, while the 28-pin PLCC package simplifies reuse of an existing J-lead board footprint. The replacement process should compare the programmed fuse or flash map, I/O polarity, chip-select timing, and power-down behavior rather than checking only the device name. A 30 ns timing budget must also be compared with the original design margin.
پیشنهادی
Display and Instrument Control
The ATF22LV10CQZ-30JU can implement control sequences, mode selection, indicator logic, and keypad or switch decoding in display and test instruments. Its 10 macrocells offer a practical balance between logic density and board complexity, making it suitable for fixed functions around a larger controller. The 3.0 V to 5.5 V operating range supports mixed-voltage instrument architecture, but output timing and input thresholds must be checked at the selected rail. Use the zero-standby power-down mode to reduce demand when the instrument enters a low-power state.
پیشنهادی
Power-Sequence and Fault Logic
ATF22LV10CQZ-30JU can combine power-good signals, fault indications, enables, and sequencing conditions into deterministic hardware logic. Using the SPLD for these functions reduces microcontroller boot dependencies and provides direct control over logical relationships. The device's edge-sensing zero standby mode reports 3 uA typical current when power-down is active, which can benefit intermittently powered equipment. The implementation must define input polarity, startup behavior, and output states during power-down so that no rail is enabled in an unsafe sequence.
پیشنهادی
Embedded System Glue Logic
The ATF22LV10CQZ-30JU is useful for glue logic between a microprocessor, memory, communications interface, and discrete peripherals. It can generate enables, qualify interrupts, route signals, and implement protocol-specific decoding where a programmable microcontroller would be excessive. Its 10 user I/O pins and 30 ns grade make it suitable for moderate-speed control paths, while electrically erasable flash permits corrections during qualification. Validate signal direction, voltage compatibility, and propagation delay at the worst operating voltage and temperature specified for the equipment.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای ATF22LV10CQZ-30JU — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | ATF22LV10CQZ-30JC | ATF22LV10C-10JU | ATF22LV10CZ-25JI | ATF22LV10CZ-25JC | GAL22V10D-7LJI |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 28-LCC (11.51 mm x 11.51 mm) | 28-LCC (11.51 mm x 11.51 mm) | 28-LCC (11.51 mm x 11.51 mm) | 28-LCC (11.51 mm x 11.51 mm) | 28-LCC (11.51 mm x 11.51 mm) | 28-LCC (11.51 mm x 11.51 mm) |
| Device Family | ATF22LV10CQZ | ATF22LV10CQZ | ATF22LV10C | ATF22LV10CZ | ATF22LV10CZ | GAL22V10D |
| Speed Designation | 30 ns | 30 ns | 10 ns designation | 25 ns | 25 ns | 7 ns designation |
| Macrocells | 10 macrocells | 10 macrocells | 10 macrocells | 10 macrocells | 10 macrocells | 10 macrocells |
| User I/O Pins | 10 pins | 10 pins | 10 pins | 10 pins | 10 pins | 10 pins |
تفاوتهای کلیدی
- Exact family and speed match for the closest ordering alternative (در مقابلATF22LV10CQZ-30JC)
- Direct 22V10 family continuity for legacy decoding designs (در مقابلATF22LV10C-10JU)
- Pin-compatible architecture with a different speed designation (در مقابلATF22LV10CZ-25JI)
- Same physical logic density in a 22V10D cross-reference family (در مقابلGAL22V10D-7LJI)
یادداشتهای طراحی
Do not treat an equivalent architecture as proof of a drop-in replacement. Validate the complete 28-pin assignment, programming file or fuse map, I/O polarity, power-down behavior, and maximum operating frequency. The -JC, -C-10, -CZ-25, and GAL22V10D alternatives may share the broad 22V10 function class, but their suffix-specific electrical or programming conditions must be compared with the original ATF22LV10CQZ-30JU design.
Operate the ATF22LV10CQZ-30JU only within its 3.0 V to 5.5 V supply range and account separately for normal operating current and the 3 uA typical zero standby state. Ensure that power-down is asserted only after downstream circuits no longer require valid outputs. If the board uses 5 V I/O, check input thresholds and output levels at the actual supply rather than assuming compatibility from the nominal rail alone.
Use the manufacturer pin-description table to assign all 28 PLCC positions and preserve the J-lead land pattern. Place the device where its grounded control paths, programmable I/O nets, and any programming or test access can be routed without long loops. Because the package is not represented by a dedicated diagram in the package library, assign PCB tracks directly from the mechanical drawing and verify pin 1 orientation during assembly review.
Analyze the design against the 30 ns propagation-delay grade with the actual clock period, output loading, and supply voltage. Include macrocell path delay, output-enable timing, and any external logic rather than comparing only the advertised speed suffix. For long interconnects or slow-changing control signals, add Schmitt conditioning where appropriate; for high-speed paths, keep loading and trace geometry within the limits established by the board validation.
The 30-JU ordering code must be preserved during procurement because package, temperature, and lead-processing details are encoded in the suffix. Before transferring a programmed design, confirm that the replacement supports the same file format and programming algorithm. A device can have the same package outline and macrocell count yet differ in fuse-map organization, test features, or supply restrictions, so create a formal pin-and-timing cross-reference for each approved alternate.
اطلاعات انطباق
No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement is included for this exact ordering code. The PLD is not an automotive-qualified device under the available information.