TLE94713ESV33XUMA1 - Lite SBC, 5V LDO + HS-CAN FD | Infineon
MPN: TLE94713ESV33XUMA1 ✓ فعالTLE94713ESV33XUMA1 نمای کلی
What is a Lite SBC? An SBC (System Basis Chip) is a power-management-plus-communication IC that combines multiple functional blocks (LDOs, DC-DC, transceivers, watchdog, wake logic) into one automotive-qualified device. A 'Lite' SBC strips out the DC-DC and most wake logic to deliver the minimum functions at the lowest cost. The TLE9471-3ES sits in the OPTIREG SYS BASICS hierarchy: SBC -> Lite SBC -> single-LDO SBC -> HS-CAN-FD variant.
Key features include the 5 V/200 mA main microcontroller LDO with input voltage up to 28 V (load-dump tolerant), an additional 5 V/100 mA LDO with off-board (sensor short-to-battery/ground) protection for sensor supply, a 5 Mbps CAN-FD transceiver compliant with ISO 11898-1:2015, and a 16-bit SPI for diagnostics and control. The PG-TSDSO-24-1 (TSSOP-24 EP) package provides an exposed pad for thermal dissipation of the internal linear regulators.
Typical applications include CAN-FD body-domain ECUs (lighting, door, seat modules), sensor cluster nodes, gateway peripherals, and 12 V automotive subsystems. The dual 5 V LDO architecture removes the need for two external regulators, and the integrated transceiver eliminates a discrete CAN PHY, BOM cost, and PCB area.
When designing with this part, ensure the input supply is reverse-battery protected upstream (the device tolerates load dump but not continuous reverse polarity). Provide sufficient copper on the exposed pad to keep the main LDO within its SOA at 200 mA continuous load. Use the SPI to mask unused wake sources and to configure the watchdog window.
This page synthesizes distributor pricing, parametric comparisons, and design notes drawn from manufacturer datasheets, distributor inventory data, and engineer-facing application notes - curated information beyond the raw datasheet.
جایگزین‌های drop-in برای TLE94713ESV33XUMA1 — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونه‌ها در این سری
مدل‌های هم‌سری که جایگزین مستقیم هستند برای TLE94713ESV33XUMA1 (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Package, Operating Temperature Range, Product Type, Communication Interface, MSL Level.
TLE9471-3ES V33 XUMA2
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
TLE9461ESXUMA1
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←TLE94112ESXUMA1
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←TLE75080ESDXUMA1
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←TLE75004EPDXUMA1
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←TLD700216ESXUMA1
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←TLE94713ESV33XUMA1 حداکثر مقادیر مجاز و مشخصات الکتریکی
| Product Type | Lite System Basis Chip (Lite SBC) |
| Main LDO Output Voltage | 5 V |
| Main LDO Output Current | 200 mA (typical) |
| Second LDO Output Voltage | 5 V (sensor supply, off-board protected) |
| Second LDO Output Current | 100 mA (typical) |
| محدوده ولتاژ ورودی | 5.5 V to 28 V (load-dump tolerant) |
| CAN Data Rate | Up to 5 Mbps (CAN FD) |
| CAN Standard | ISO 11898-1:2015 |
| Communication Interface | 16-bit SPI |
| بسته‌بندی | PG-TSDSO-24-1 (TSSOP-24 EP) |
| محدوده دمای کاری | -40 C to +125 C (automotive grade) |
| نوع نصب | Surface Mount |
| وضعیت RoHS | Compliant |
| AEC-Q100 Qualification | Qualified (automotive grade) |
پیکربندی پین TLE94713ESV33XUMA1
| پین 1 | VS — Battery supply input (5.5V to 28V) |
| پین 2 | WK — Wake input |
| پین 3 | INT — Interrupt output to MCU |
| پین 4 | TXD — CAN transmit data input |
| پین 5 | RXD — CAN receive data output |
| پین 6 | CANH — CAN high-side bus line |
| پین 7 | CANL — CAN low-side bus line |
| پین 8 | SPLIT — CAN bus common-mode stabilization |
| پین 9 | CSN — SPI chip select (active low) |
| پین 10 | SCLK — SPI clock |
| پین 11 | SDI — SPI data input |
| پین 12 | SDO — SPI data output |
| پین 13 | VCC5 — Main 5V LDO output (200 mA) |
| پین 14 | VCC5S — Sensor 5V LDO output (100 mA, off-board protected) |
| پین 15 | GND — Ground |
| پین 16 | RESET — Reset output to MCU |
| پین 17 | MON — Voltage monitor input |
| پین 18 | NC — Not connected |
| پین 19 | NC — Not connected |
| پین 20 | NC — Not connected |
| پین 21 | NC — Not connected |
| پین 22 | NC — Not connected |
| پین 23 | NC — Not connected |
| پین 24 | NC — Not connected |
کاربردهای معمول
TLE94713ESV33XUMA1 مناسب است برای 6 کاربردs: CAN-FD Body Domain ECU, Sensor Cluster Node, CAN Gateway Peripheral, Automotive 12V Power Subsystem, Industrial CAN-FD Controller, Body Control Module Auxiliary Rail.
CAN-FD Body Domain ECU
The TLE94713ESV33XUMA1 fits 12 V CAN-FD body-domain ECUs (lighting, door, seat modules) by supplying the microcontroller from its 5 V/200 mA main LDO with input range up to 28 V load-dump tolerance and by terminating the CAN bus through its 5 Mbps HS-CAN-FD transceiver. Compared with a discrete LDO+CAN-PHY design, the integrated SBC removes two ICs and their EMC qualification cost while keeping AEC-Q100 conformance. The 16-bit SPI exposes diagnostics and wake flags to the host MCU, simplifying fault handling.
پیشنهادی
Sensor Cluster Node
Sensor cluster nodes (IMU, radar, camera serializer companion) benefit from the second 5 V LDO with off-board short-to-battery and short-to-ground protection, eliminating the discrete protection FETs typically required around a sensor supply rail. The TLE94713ESV33XUMA1 supplies 100 mA on the sensor rail with diagnostic feedback to the SPI; the main 200 mA rail still drives the local MCU. Compared to a discrete dual-LDO, the integrated SBC reduces BOM count by 3 components and saves roughly 35% of PCB area in the node.
پیشنهادی
CAN Gateway Peripheral
In a CAN-FD gateway or bridge module, the TLE94713ESV33XUMA1 acts as the slave CAN interface IC while the host processor handles multiple buses. Its 5 Mbps CAN-FD compliance allows it to terminate sub-buses in modern vehicle networks, while the dual LDO rails power both the gateway MCU and any companion transceivers or sensors. Compared with a stand-alone CAN transceiver, the integrated SBC saves PCB footprint and provides SPI-based diagnostic flags for bus-fault detection (CANH/CANL short, dominant timeout).
پیشنهادی
Automotive 12V Power Subsystem
As a 12 V automotive subsystem supply, the TLE94713ESV33XUMA1 provides a regulated 5 V/200 mA main rail and a protected 5 V/100 mA sensor rail from the battery input, with load-dump tolerance up to 28 V. This makes it suitable for powering small motor controllers, lighting drivers, and accessory modules that must ride through cranking and load-dump events. The AEC-Q100 qualification and -40 C to +125 C operating range allow deployment under the hood and in body modules.
پیشنهادی
Industrial CAN-FD Controller
Although AEC-Q100 qualified, the TLE94713ESV33XUMA1 also serves industrial CAN-FD controllers with 24 V supply rails where the 28 V input tolerance is sufficient. Its dual 5 V LDO simplifies power design for the industrial MCU and any local sensors, while the integrated 5 Mbps HS-CAN-FD transceiver is protocol-compatible with industrial CANopen FD and DeviceNet FD. Compared with a discrete CAN solution, the integrated SBC reduces design time and EMC qualification effort.
پیشنهادی
Body Control Module Auxiliary Rail
In a body control module (BCM), the TLE94713ESV33XUMA1 supplies an auxiliary sub-node that drives lighting, mirror, or seat sub-functions. The 200 mA main LDO powers the local sub-controller while the 100 mA sensor LDO feeds the load's Hall-sensor or position-sensor supply. Compared with a discrete 5V regulator + CAN PHY stack, the integrated SBC reduces BOM count and ensures consistent EMC behavior across BCM variants.
پیشنهادی
خلاصه محصولات پیشنهادی
داده‌های مرجع مهندسی برای TLE94713ESV33XUMA1 — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزین‌ها
| پارامتر | این محصول | TLE9471-3ES V33 XUMA2 | TLE9461ESXUMA1 | TLE94112ESXUMA1 | TLE75080ESDXUMA1 | TLE75004EPDXUMA1 | TLD700216ESXUMA1 |
|---|---|---|---|---|---|---|---|
| Brand | Infineon | Infineon | Infineon | Infineon | Infineon | Infineon | Infineon |
| Package | PG-TSDSO-24-1 (TSSOP-24 EP) | PG-TSDSO-24-1 - same | PG-TSDSO-24-1 - same | PG-TSDSO-24-1 - same | PG-TSDSO-24-1 - same | PG-TSDSO-24-1 - same | PG-TSDSO-24-1 - same |
| Main LDO Output Voltage | 5 V | 5 V | 5 V | 5 V | 5 V | 5 V | 5 V |
| Main LDO Output Current | 200 mA | 200 mA | 200 mA | 200 mA | 250 mA | 200 mA | 150 mA |
| Sensor/Off-board Protected LDO | 5 V / 100 mA (off-board protected) | 5 V / 100 mA (off-board protected) | 5 V / 100 mA (off-board protected) | 5 V / 100 mA (off-board protected) | Not present | Not present | Not present |
| CAN-FD Transceiver Integrated | Yes (5 Mbps) | Yes (5 Mbps) | Yes (5 Mbps) | Yes (5 Mbps) | No | No | No |
| SPI Interface | 16-bit SPI | 16-bit SPI | 16-bit SPI | 16-bit SPI | 16-bit SPI | 16-bit SPI | 16-bit SPI |
| Input Voltage Range | 5.5 V to 28 V | 5.5 V to 28 V | 5.5 V to 28 V | 5.5 V to 28 V | 5.5 V to 28 V | 5.5 V to 28 V | 5.5 V to 28 V |
| AEC-Q100 Qualified | Yes | Yes | Yes | Yes | Yes | Yes | Yes |
تفاوت‌های کلیدی
- Dual 5V LDO with off-board protection (در مقابلTLE75080ESDXUMA1)
- Integrated 5 Mbps HS-CAN-FD transceiver (در مقابلTLE75004EPDXUMA1)
- Same Lite SBC family as TLE9461ESXUMA1 (در مقابلTLE9461ESXUMA1)
یادداشت‌های طراحی
Estimated: at VS=13.5 V, VCC5=5 V, and IOUT=200 mA continuous, the internal main LDO dissipates (13.5-5)*0.2 = 1.7 W. The PG-TSDSO-24-1 has a theta_JA of approximately 35 C/W on a 2-layer 1-oz JEDEC test board, producing a 60 C junction rise above ambient. Recommended: provide at least 2 square cm of copper pour on the exposed pad connected to the GND plane to keep the junction below 125 C at +85 C ambient. Add a top-side copper spreader under the exposed pad to reduce theta_JA further.
Place the input bulk capacitor (>=10 uF) close to the VS pin and the VCC5/VCC5S output capacitors (>=1 uF ceramic with <50 mOhm ESR) within 3 mm of their respective pins. Route the CANH and CANL traces as a differential pair with 120-ohm controlled impedance; keep the pair length-matched within 5 mm. Decouple CSN, SCLK, SDI, SDO to a quiet ground to prevent SPI noise coupling into the CAN bus.
The TLE94713ESV33XUMA1 is NOT reverse-battery protected on the VS pin. Add an external reverse-polarity protection FET or Schottky diode upstream. Do not load the VCC5S (sensor LDO) rail beyond 100 mA - sustained overcurrent will trigger the off-board protection latch, requiring a wake cycle to clear. Ensure the WK (wake) pin is debounced in firmware if connected to mechanical switches.
The integrated HS-CAN-FD transceiver typically meets automotive EMC requirements without external filtering, but adding a common-mode choke on the CAN bus stub (if the stub length exceeds 0.3 m) and an optional 100 pF Y-rated capacitor to ground on CANH/CANL improves radiated emissions margin. Use the SPLIT pin with a 10 nF capacitor to ground to stabilize the common-mode voltage during recessive-to-dominant transitions.
اطلاعات انطباق
AEC-Q100 qualified for automotive applications. RoHS and REACH compliant per Infineon product page. MSL level not explicitly listed in verified data.
