SN65HVD52D vs SN65HVD37D Comparaison
Comparaison détaillée côte à côte de SN65HVD52D par Texas Instruments et SN65HVD37D par Texas Instruments. Comparez les spécifications clés, les paramètres électriques, le conditionnement, le statut de cycle de vie, les prix et la disponibilité pour déterminer le meilleur composant pour vos exigences de conception.
Texas Instruments
SN65HVD52D - 1 Mbps Full-Duplex RS-485 Transceiver | Texas Instruments
SN65HVD52D ✓ ActifTexas Instruments
SN65HVD37D - 3.3V Full-Duplex RS-485 Transceiver | TI (Tape & Reel)
SN65HVD37D ✓ ActifComparaison des spécifications
| Paramètre | SN65HVD52D | SN65HVD37D |
|---|---|---|
| Marque | Texas Instruments | Texas Instruments |
| Catégorie | Interface ICs | Interface ICs |
| Statut du cycle de vie | Actif | Actif |
| Product Type | RS-485 / RS-422 full-duplex transceiver | — |
| Driver / Receiver Count | 1 driver and 1 receiver | — |
| Débit de données | 1 Mbps | — |
| Tension d'alimentation | 5 V | — |
| Maximum Supply Voltage | 5.5 V | — |
| Température de fonctionnement | -40 C to +85 C | -40 C to +85 C |
| Boîtier | 8-pin SOIC (D) | 14-SOIC (D), 0.154" / 3.90 mm width |
| Type de montage | Surface mount | Surface Mount |
| Driver Configuration | Full-duplex | — |
| Bus Standard | RS-485 and RS-422 | — |
| Unit Load | 1/8 unit-load option | — |
| Maximum Bus Nodes | Up to 256 nodes | — |
| Bus-Pin ESD Protection | Exceeds 15 kV HBM | — |
| Standby Current | 1 uA | — |
| Maximum Transmit Delay | 230 ns | — |
| Maximum Supply Current | 8 mA | — |
| Interface Standard | EIA-485-A | — |
| Statut RoHS | [DATA_NEEDED: RoHS compliance status] | — |
| REACH Status | [DATA_NEEDED: REACH compliance status] | — |
| AEC-Q100 Qualification | [DATA_NEEDED: AEC-Q100 qualification status] | — |
| Device Type | — | Transceiver (1 driver / 1 receiver) |
| Protocol | — | RS-422, RS-485 |
| Number of Drivers/Receivers | — | 1 / 1 |
| Duplex | — | Full |
| Supply Voltage (VCC) | — | 3 V to 3.6 V (nominal 3.3 V) |
| Signaling Rate | — | Up to 25 Mbps |
| Receiver Unit Load | — | 1/8 unit load (up to 256 nodes) |
| Bus-Pin ESD Protection (HBM) | — | >15 kV HBM |
| Receiver Hysteresis | — | 60 mV (typical) |
| Quiescent Current (active) | — | 1 mA (typical) |
| Standby / Shutdown Current | — | <1 uA (typical) |
| RoHS / Lead-Free | — | RoHS compliant, lead-free (per TI product page) |
| Fail-Safe Receiver | — | Yes (idle/open/short safe) |
| Driver / Receiver Enable | — | Independent DE and RE pins |