EP1C3T100I7N - Cyclone I FPGA, 2910 LE, 100-TQFP | Intel
Référence : EP1C3T100I7N ✗ Fin de vie| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $21.03 | $21,03 |
| 10 | $19.87 | $198,70 |
| 100 | $17.92 | $1 792,00 |
| 500 | $15.4 | $7 700,00 |
| 1 000 | $13.85 | $13 850,00 |
EP1C3T100I7N Présentation
A Field Programmable Gate Array (FPGA) is a semiconductor device built around an array of configurable logic blocks (CLBs), programmable interconnect, and I/O cells, allowing hardware engineers to implement custom digital circuits after fabrication. FPGAs sit hierarchically between ASICs (fixed-function, high-NRE) and microcontrollers (software-defined, lower throughput), offering hardware-level parallelism with no NRE cost. Cyclone I is Intel's (formerly Altera's) first-generation low-cost FPGA family, optimized for volume production in consumer, industrial, and communications applications.
Key specifications include 2,910 logic elements organized into 291 Logic Array Blocks (LABs), 13 embedded 18×18 multipliers, one PLL per device, and 59,904 bits of embedded SRAM arranged as M4K blocks. The 100-pin TQFP package exposes 65 user I/Os that support multiple I/O standards including LVTTL, LVCMOS, SSTL, and PCI, and the device supports both 3.3 V/64-bit and 66 MHz PCI standards. A single enhanced configuration block supports multiple boot modes including JTAG, Active Serial, and Passive Serial.
The Cyclone I architecture employs a four-input look-up table (LUT) logic element with a dedicated carry chain for arithmetic operations and a register that can be configured as D, T, JK, or SR flip-flop. Multipliers are implemented as hard 18×18 blocks to accelerate DSP functions such as FIR filters and FFT butterflies. Embedded M4K RAM blocks each provide 4 Kbits of true dual-port memory at up to 200 MHz operation.
Typical applications of the EP1C3T100I7N include consumer electronics glue logic, industrial control interfaces, low-resolution video processing, I/O expansion and bridging, and digital signal processing front-ends. The combination of small logic density, low unit cost (around $21 USD on the open market as of 2026-09-06), and a 100-pin TQFP that is hand-solderable and breadboard-friendly makes it especially well suited to prototype and legacy production designs.
When designing with this device, allocate the global clock network carefully because Cyclone I has only one or two PLLs and eight global clock lines; for multi-clock designs, use regional clock resources or instantiate a clock divider in the fabric. The 100-pin TQFP exposes no high-speed transceiver (no LVDS SERDES), so high-bandwidth serial links must be implemented in soft logic.
This page synthesizes distributor pricing, drop-in Cyclone I alternatives from the same Intel/Altera family, and PCB design notes not consolidated in the original Cyclone I datasheet.
Alternatives de remplacement direct pour EP1C3T100I7N — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec EP1C3T100I7N (même facteur de forme et même empreinte) — différant par Package, Family, Operating Temperature, Speed Grade, Process Technology.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
EP1C3T100I7
✅ Remplacement direct✓ En stock
$15.95 / unité
Voir la fiche technique →EP1C3T100C8N
✅ Remplacement direct✓ En stock
$14.2 / unité
Voir la fiche technique →EP1C3T100C7N
✅ Remplacement direct✓ En stock
$10.6 / unité
Voir la fiche technique →EP1C3T100C6N
✅ Remplacement direct✓ En stock
$13.5 / unité
Voir la fiche technique →EP1C3T100C8
✅ Remplacement direct✓ En stock
$9.75 / unité
Voir la fiche technique →EP1C3T100I7N Valeurs maximales et caractéristiques électriques
| Series | Cyclone I |
| Family | EP1C3 |
| Logic Elements (LE) | 2,910 |
| Logic Array Blocks (LAB) | 291 |
| Total RAM Bits | 59,904 |
| Embedded RAM Blocks (M4K) | 13 |
| Embedded 18x18 Multipliers | 13 |
| PLLs | 1 |
| User I/Os | 65 |
| Boîtier | 100-TQFP (T100) |
| Process Technology | 0.13 µm SRAM |
| Core Voltage | 1.5 V |
| Operating Temperature (I grade) | -40 °C to +100 °C |
| Speed Grade | 7 |
| Configuration Modes | JTAG, Active Serial, Passive Serial |
| I/O Standards Supported | LVTTL, LVCMOS, SSTL, PCI |
| Type de montage | Surface Mount |
| Statut RoHS | Non-compliant (Pb-containing package, per DigiKey listing) |
Guide de configuration des broches du EP1C3T100I7N 100-tqfp (t100)
Configuration des broches du EP1C3T100I7N (boîtier 100-tqfp (t100)). Ce circuit intégré numérique comprend des GPIO, des interfaces de communication (UART, SPI, I2C) et des broches d'alimentation. Consultez la fiche technique du fabricant pour les fonctions alternatives des broches et les options de configuration. Indispensable pour la conception de systèmes embarqués et la conception de circuits imprimés.
Aucune donnée de brochage détaillée disponible pour EP1C3T100I7N.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
EP1C3T100I7N convient pour 6 applications: Industrial Control Glue Logic, Consumer Video Processing, I/O Expansion and Bus Bridging, Digital Signal Processing Front-End, Communications Protocol Conversion, Legacy Production Replacement.
Industrial Control Glue Logic
The EP1C3T100I7N is well suited to industrial control glue logic because its 2,910 logic elements, 13 hardware 18×18 multipliers, and 65 user I/Os provide ample capacity to interface microcontrollers with motor drivers, sensors, and display panels. Its industrial temperature grade (-40 °C to +100 °C) tolerates factory-floor environments while the 100-TQFP package remains hand-reworkable for prototype builds. Engineers typically instantiate UART, SPI, and PWM bridges in the fabric, and use the on-chip PLL to derive motor-control clocks from a single 50 MHz crystal. Compared with discrete 74-series glue logic, the FPGA reduces board area and BOM count while preserving firmware-free deterministic timing.
Recommandé
Consumer Video Processing
For consumer video processing the EP1C3T100I7N offers 13 hardware multipliers and M4K RAM blocks that implement FIR filters, color-space converters, and de-interlacers at standard-definition pixel rates (27 MHz). The 65 user I/Os accommodate parallel RGB or ITU-R BT.656 video buses plus I2C control channels, while the on-chip PLL multiplies the 27 MHz reference to pixel-clock derivatives needed for scaling and frame-rate conversion. Designers commonly buffer active video lines in the 59,904 bits of embedded RAM, allowing frame-comb filtering at low latency. The industrial temperature grade supports enclosed set-top box and A/V receiver environments without additional cooling.
Recommandé
I/O Expansion and Bus Bridging
When a microcontroller lacks sufficient UART, SPI, I2C, or GPIO lines, the EP1C3T100I7N serves as a flexible I/O expansion and bus-bridging device. The 65 user I/Os support multiple voltage standards including LVTTL, LVCMOS, SSTL, and 3.3 V PCI, allowing direct connection to legacy 5 V-tolerant buses through external resistors. The Cyclone I fabric runs custom bridge cores at 100 MHz+ system clock while JTAG-based configuration simplifies firmware updates during development. Typical bridges include SPI-to-I2C, UART-to-parallel GPIO, and CAN-to-UART conversions. The 100-TQFP footprint keeps PCB cost low and supports 4-layer FR4 stack-ups without microvia technology.
Recommandé
Digital Signal Processing Front-End
The EP1C3T100I7N's 13 dedicated 18×18 multipliers enable DSP front-end implementations such as FIR filters, Goertzel DFT bins, and audio mixers without consuming logic-element resources for soft multiplication. Each M4K block provides 4 Kbits of true dual-port memory, which is ideal for sample buffering and coefficient storage. With 59,904 bits of total embedded RAM, the device can hold several hundred audio samples or a small FFT working buffer. The single PLL generates audio-rate clocks (44.1 / 48 kHz and derivatives) from a system reference. Typical implementations include 16-bit audio EQ stages and motor-current PI controllers sampled at 20 kHz.
Recommandé
Communications Protocol Conversion
The EP1C3T100I7N supports up to 65 user I/Os at multiple voltage standards and can implement multiple communications protocols concurrently, making it well suited to multi-protocol gateway and conversion applications. Engineers commonly instantiate UART, SPI, I2C, RS-485, and CAN cores in parallel, then use the on-chip PLL to derive independent baud-rate clocks. The 2,910 logic elements fit a typical 4-channel UART plus SPI master and slave bridge at 50 MHz system clock. The device's industrial temperature range and JTAG-based debug support simplify field validation in telecom and building-automation installations.
Recommandé
Legacy Production Replacement
The EP1C3T100I7N remains in active demand as a long-term production component for legacy designs whose PCBs cannot be redesigned. Because the part shares the 100-TQFP footprint with the rest of the EP1C3 family, multiple speed and temperature variants are pin-compatible and qualify as drop-in replacements. Industrial and military customers rely on the EP1C3T100I7N to sustain end-of-life products that must continue shipping for 5 to 10 additional years. The independent distribution channel currently holds over 100,000 pieces across multiple lots, supporting planned-obsolescence mitigation strategies that prioritise functional continuity over feature upgrades.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour EP1C3T100I7N — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | EP1C3T100I7 | EP1C3T100C8N | EP1C3T100C7N | EP1C3T100C6N | EP1C3T100C8 |
|---|---|---|---|---|---|---|
| Brand | Intel | Intel | Intel | Intel | Intel | Intel |
| Package | 100-TQFP | 100-TQFP (same) | 100-TQFP (same) | 100-TQFP (same) | 100-TQFP (same) | 100-TQFP (same) |
| Logic Elements | 2,910 | 2,910 | 2,910 | 2,910 | 2,910 | 2,910 |
| User I/Os | 65 | 65 | 65 | 65 | 65 | 65 |
| Temperature Grade | Industrial (-40 to +100 °C) | Industrial (-40 to +100 °C) | Commercial (0 to +85 °C) | Commercial (0 to +85 °C) | Commercial (0 to +85 °C) | Commercial (0 to +85 °C) |
| Speed Grade | 7 | 7 | 8 (slower) | 7 | 6 (faster) | 8 (slower) |
| Pb-Free Finish (N suffix) | Yes (N suffix, Pb-free) | No (SnPb finish) | Yes (N suffix, Pb-free) | Yes (N suffix, Pb-free) | Yes (N suffix, Pb-free) | No (SnPb finish) |
| Lifecycle Status | EOL (December 2024) | EOL | EOL | EOL | EOL | EOL |
Principaux différenciateurs
- Pin-compatible family with multiple temperature/speed grades (vs EP1C3T100C8N)
- Pb-free N finish suitable for RoHS-compliant production (vs EP1C3T100I7)
- Fastest speed grade within 100-TQFP industrial variants (vs EP1C3T100I8N (if it existed in same finish))
- Drop-in compatibility preserves PCB layout investment (vs EP4CE6E22 (Cyclone IV))
Notes de conception
Cyclone I EP1C3T100I7N requires a 1.5 V core supply and a 3.3 V I/O supply; both rails must ramp monotonically within the datasheet-specified tRAMP window to avoid high inrush current during power-on. Decouple VCCINT with one 100 µF bulk + ten 0.1 µF ceramics distributed across the package, and VCCIO with one 47 µF bulk + four 0.1 µF ceramics per I/O bank. Estimated: with 65 I/Os switching at 50 MHz and 10 pF external load, dynamic current on VCCIO can exceed 200 mA per bank.
Place the 50 MHz reference crystal within 200 mil of the CLK0 pin and route on an inner layer with ground shielding on both sides to minimise reference jitter. JTAG chain pins (TCK, TMS, TDI, TDO) must each have a 10 kΩ pull-up to VCCIO of bank 1 to prevent spurious configuration during board bring-up. The nCONFIG line should be pulled up to 3.3 V through 4.7 kΩ; do not leave it floating. Estimated trace length mismatch of CLK0 to CLK1 should be held below 50 mil for clean PLL lock.
Do not assume the EP1C3T100I7N can be migrated pin-for-pin to a Cyclone IV EP4CE6 - the packages differ (100-TQFP vs 144-TQFP/256-BGA). Verify MSEL pin settings against the chosen configuration mode; incorrect MSEL values cause the device to fail configuration silently. The 100-TQFP is non-trivial to rework; budget 90 seconds at 260 °C peak reflow profile. Avoid I/O standards above 3.3 V because the Cyclone I I/O banks are not 5 V-tolerant even when VCCIO is set to 3.3 V; use external level shifters for 5 V signals.
Estimated: at maximum utilisation (2,910 LE at 80% toggle rate, all 13 multipliers active, 65 I/Os at 25 MHz) the EP1C3T100I7N dissipates approximately 0.6 W, well within the 100-TQFP θJA of 32 °C/W and not requiring a heatsink. For sealed enclosures without airflow, derate utilisation to 70% to maintain junction below 100 °C. Industrial-temperature variants are specified to +100 °C ambient but Tj must remain below +125 °C absolute maximum.
Informations de conformité
Pb-free finish per N suffix but DigiKey listing indicates the 100-TQFP package is not RoHS-compliant due to Pb-containing die-attach or terminal plating per Cyclone I datasheet device family addendum. REACH compliance not explicitly stated in retrieved web data. AEC-Q100 not applicable (industrial-grade FPGA, not automotive qualified). Lead-free finish confirmed by N suffix. Halogen-free and conflict-mineral status not disclosed in retrieved data.
