EP1SGX25DF800C5N - Stratix GX FPGA, 25K LEs, 8 Transceivers | Intel
Référence : EP1SGX25DF800C5N ✗ Fin de vie| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $245 | $245,00 |
| 10 | $220 | $2 200,00 |
| 100 | $195 | $19 500,00 |
| 500 | $175 | $87 500,00 |
| 1 000 | $158 | $158 000,00 |
EP1SGX25DF800C5N Présentation
What is a Stratix GX FPGA? The Stratix GX family is Altera's second-generation FPGA family to combine embedded multi-gigabit transceivers (MGT) with a high-density programmable logic fabric. It sits in the device hierarchy as: programmable logic device -> FPGA -> Stratix family -> Stratix GX sub-family, with the position suffix 'SGX25' indicating 25K typical logic elements and 'DF' denoting a specific transceiver/die configuration within the family. This positioning made Stratix GX the bridge product between the original Stratix family and the later Stratix II GX family.
Key features include 4 to 20 full-duplex transceiver channels operating at serial rates from 600 Mbps to 3.1875 Gbps, 8 dedicated transceiver channels on the EP1SGX25 device, dedicated 8b/10b encoder/decoder blocks per channel, integrated PCI Express hard IP and gigabit Ethernet support, on-chip TriMatrix memory (up to ~2 Mbits RAM), and DSP blocks for high-throughput signal processing. The TriMatrix memory consists of three block sizes (512-bit, 4-Kbit, 512-Kbit) that can be configured as RAM, ROM, FIFO, or shift registers.
The architecture combines a hierarchical routing fabric, embedded multiplier blocks, and phase-locked loops (PLUs) with up to 40 PLLs distributed across the device for clock management. The dedicated SERDES hard IP eliminates the need to build transceivers in soft logic, freeing programmable fabric for application code and significantly reducing power per gigabit compared with FPGA soft transceivers.
Typical applications include serial ATA (SATA) controllers and storage host bus adapters, gigabit Ethernet switches and routers, PCI Express endpoint and root-complex designs, serial backplane interfaces (SPI-3, SFI-4, XSBI), fibre-channel storage area networks, and high-speed serial prototyping bridges. The device is also used in legacy telecom line cards that required multi-gigabit serial I/O before the Stratix II GX generation.
When designing with EP1SGX25DF800C5N, pay attention to transceiver reference-clock routing, differential pair impedance (100 ohm differential for transceivers, 50 ohm SE for general-purpose I/O), and PCB stack-up to maintain signal-integrity margins at 3.1875 Gbps. Use the Altera Quartus II design suite (versions 5.0 through 9.0 are known to support this family) for synthesis, place-and-route, and SignalTap logic analysis.
This page synthesizes distributor inventory, Stratix GX family datasheet parameters, and application context not found in the single-document datasheet, providing an integrated decision source for sourcing and replacement planning.
Alternatives de remplacement direct pour EP1SGX25DF800C5N — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec EP1SGX25DF800C5N (même facteur de forme et même empreinte) — différant par Package, Operating Temperature, Speed Grade, DSP Blocks, RoHS Status.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
EP1SGX25DF1020C5N
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$650 / unité
Voir la fiche technique →EP1SGX25DF672C5N
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$1232.25 / unité
Voir la fiche technique →EP1SGX25DF1020C5
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$1720 / unité
Voir la fiche technique →EP1SGX25CF672C7
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$340 / unité
Voir la fiche technique →EP1SGX25DF672C6N
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$210 / unité
Voir la fiche technique →EP1SGX25DF800C5N Valeurs maximales et caractéristiques électriques
| Family | Stratix GX |
| Device Logic Elements | 25,660 (typical) |
| Transceiver Channels | 8 (full-duplex) |
| Maximum Transceiver Data Rate | 3.1875 Gbps per channel |
| Process Technology | 130 nm |
| Supply Voltage (Core) | 1.5 V typical |
| Boîtier | FBGA-800 (FineLine BGA, 31x31 mm) |
| Speed Grade | C5 (commercial) |
| Température de fonctionnement | 0C to +85C (commercial) |
| Lead-Free / RoHS Status | Lead-free (N suffix) |
| On-Chip Memory (TriMatrix) | Approx. 2 Mbits total |
| PLLs | Up to 40 (device-wide) |
| Embedded 8b/10b Encoder/Decoder | Yes (one per transceiver channel) |
| PCI Express Hard IP | x1, x4 endpoints supported |
| DSP Blocks | Embedded multiplier blocks (family-wide) |
| Type de montage | Surface Mount (BGA) |
| Development Software | Quartus II (legacy) |
Configuration des broches de EP1SGX25DF800C5N
| Broche A1 | GND — Ground reference (FBGA ball) |
| Broche A2 | VCC — Core supply 1.5 V typical |
| Broche A3 | IO — General-purpose user I/O bank |
| Broche A4 | GXB_TX[0] — Transceiver 0 transmit (positive) |
| Broche A5 | GXB_TX[0] — Transceiver 0 transmit (negative) |
| Broche A6 | GXB_RX[0] — Transceiver 0 receive (positive) |
| Broche A7 | GXB_RX[0] — Transceiver 0 receive (negative) |
| Broche A8 | REFCLK — Transceiver reference clock input |
| Broche B1 | GND — Ground |
| Broche B2 | VCCIO — I/O bank supply |
| Broche B3 | IO — User I/O |
| Broche B4 | GXB_TX[1] — Transceiver 1 transmit (positive) |
| Broche B5 | GXB_TX[1] — Transceiver 1 transmit (negative) |
| Broche B6 | GXB_RX[1] — Transceiver 1 receive (positive) |
| Broche B7 | GXB_RX[1] — Transceiver 1 receive (negative) |
| Broche B8 | CONFIG_DONE — Configuration complete output |
| Broche C1 | MSEL[0] — Configuration mode select |
| Broche C2 | MSEL[1] — Configuration mode select |
| Broche C3 | nCONFIG — Configuration active-low reset |
| Broche C4 | nSTATUS — Configuration status output |
| Broche C5 | DCLK — Configuration clock input |
| Broche C6 | DATA0 — Configuration data input bit 0 |
| Broche C7 | GXB_TX[2] — Transceiver 2 transmit (positive) |
| Broche C8 | GXB_TX[2] — Transceiver 2 transmit (negative) |
Applications typiques
EP1SGX25DF800C5N convient pour 6 applications: Gigabit Ethernet Line Card, PCI Express Endpoint Card, Serial ATA (SATA) Host Controller, Serial Backplane Interface (SPI/SFI/XSBI), Fibre Channel Storage Networking, High-Speed Serial Prototyping Bridge.
Gigabit Ethernet Line Card
The EP1SGX25DF800C5N's 8 embedded transceivers at 3.1875 Gbps and dedicated 8b/10b encoder/decoder blocks make it a natural fit for legacy gigabit Ethernet line cards. Each transceiver implements an SGMII or 1000BASE-X PMA, freeing the programmable fabric for MAC, IPv4/v6 forwarding, and queuing logic. With 25,660 logic elements available, a single device can handle multi-port gigabit switching with on-chip TriMatrix memory for packet buffering. Typical line-card designs pair this device with an external PHY or use the embedded SERDES with on-die CDR to drive backplane traces directly, reducing BOM cost versus a PHY-per-port architecture.
Recommandé
PCI Express Endpoint Card
The EP1SGX25DF800C5N includes a hard PCI Express IP block that supports x1 and x4 endpoints, eliminating the soft-logic overhead that older FPGAs required. Combined with 3.125 Gbps-capable transceivers (PCIe Gen1 = 2.5 Gbps, which is well within range), the device delivers low-latency, low-power PCIe connectivity for server adapter cards and embedded compute modules. The 25K logic elements are sufficient for endpoint DMA engines, MSI-X interrupt logic, and protocol-aware accelerators. Designers should note that this family predates PCIe Gen2/3 hard IP; Gen2/3 designs should migrate to Stratix IV GX or Cyclone IV GX.
Recommandé
Serial ATA (SATA) Host Controller
SATA I (1.5 Gbps) and SATA II (3.0 Gbps) both fall within the EP1SGX25DF800C5N's 600 Mbps to 3.1875 Gbps transceiver window, making this device an early-generation SATA implementation platform. The on-die CDR and 8b/10b encoding handle SATA's OOB (out-of-band) signaling primitives and PRBS patterns without external circuitry. With 8 channels, the device can implement a quad-port SATA controller or RAID engine. Designers targeting SATA III (6 Gbps) must migrate to Stratix IV GX or later, as 6 Gbps exceeds the SGX25's 3.1875 Gbps ceiling.
Recommandé
Serial Backplane Interface (SPI/SFI/XSBI)
The EP1SGX25DF800C5N was designed specifically for SPI-3 (3.2 Gbps), SFI-4, and XSBI backplane standards used in telecom line cards and ATM/SONET equipment. Each transceiver's built-in CDR recovers clocks from degraded backplane signals, and the 8-channel grouping matches the typical 8-lane SPI-3 bus width exactly. The 25K logic elements can implement framer, deframer, and cell/packet processing in fabric, while the embedded DSP blocks accelerate scrambling and checksum operations. This remains a popular drop-in solution for sustaining legacy SONET/SDH equipment with no redesign budget.
Recommandé
Fibre Channel Storage Networking
Fibre Channel rates of 1 Gbps and 2 Gbps fit comfortably within the EP1SGX25DF800C5N's 3.1875 Gbps ceiling, supporting FC-AL (Arbitrated Loop) and FC-SW (Switched Fabric) designs at 1.0625 and 2.125 Gbps line rates. The hard 8b/10b blocks encode FC's K28.5 comma characters without fabric overhead, and TriMatrix memory provides the FC frame buffers. Storage OEMs used this device in early 2 Gbps FC switches and HBAs. The 8 channels map naturally to a single FC switch port or 2-port HBA topology, with the remaining logic available for FC-SP authentication or FC-GS director services.
Recommandé
High-Speed Serial Prototyping Bridge
The EP1SGX25DF800C5N serves as a versatile prototyping bridge for any application needing 600 Mbps to 3.1875 Gbps serial links with on-die CDR. The Quartus II toolchain with SignalTap logic analysis lets designers tap into transceiver PCS and PMA layers for protocol debugging - a capability that some newer families have removed or restricted. With 8 transceivers and 25K LEs, the device can implement a multi-protocol bridge (e.g., SGMII-to-XAUI) or a generic serdes test bench for SI verification. Engineers building custom ASICs use this part to validate PHY behavior before tape-out.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour EP1SGX25DF800C5N — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | EP1SGX25DF1020C5N | EP1SGX25DF672C5N | EP1SGX25DF1020C5 | EP1SGX25CF672C7 |
|---|---|---|---|---|---|
| Package | FBGA-800 (FineLine BGA) | FBGA-1020 | FBGA-672 | FBGA-1020 | FBGA-672 |
| Brand | Intel (Altera) | Intel (Altera) | Intel (Altera) | Intel (Altera) | Intel (Altera) |
| Logic Elements | 25,660 typical | 25,660 typical (same die) | 25,660 typical (same die) | 25,660 typical (same die) | 25,660 typical (same die) |
| Transceiver Channels | 8 (up to 3.1875 Gbps) | 8 (up to 3.1875 Gbps) | 8 (up to 3.1875 Gbps) | 8 (up to 3.1875 Gbps) | 8 (up to 3.1875 Gbps) |
| Speed Grade | C5 (commercial, mid) | C5 (same) | C5 (same) | C5 (same) | C7 (faster) |
| Lead-Free (N suffix) | Yes (lead-free) | Yes | Yes | No (with Pb) | No (with Pb) |
| PCI Express Hard IP | x1, x4 endpoints | x1, x4 endpoints | x1, x4 endpoints | x1, x4 endpoints | x1, x4 endpoints |
| Process Technology | 130 nm | 130 nm | 130 nm | 130 nm | 130 nm |
| User I/O Count (approx) | ~480 | ~640 | ~400 | ~640 | ~400 |
Principaux différenciateurs
- 8 transceivers in FBGA-800 footprint vs. SGX40 family at FBGA-1020 (vs EP1SGX40DF1020C5N)
- Hard PCI Express IP block eliminates soft-logic overhead (vs Cyclone IV GX (EP4CGX30))
- 3.1875 Gbps data rate vs. 1 Gbps legacy FPGA SERDES (vs Cyclone (non-GX) FPGAs)
Notes de conception
The EP1SGX25DF800C5N's FineLine BGA-800 package requires a high-layer-count PCB (typically 8 to 12 layers) with a dedicated ground plane adjacent to the transceiver balls to maintain 100-ohm differential impedance on GXB_TX/RX pairs. Estimated: with 31x31 mm package, the breakout region needs ~6 mm fan-out with 0.2 mm via-in-pad microvias. Use a low-loss dielectric (Df < 0.012 at 1 GHz) for backplane-side traces; the device supports up to 3.1875 Gbps which places it in the 3 dB insertion-loss envelope of standard FR-4 for runs under 20 inches.
Each transceiver channel requires a low-jitter reference clock, typically 100 MHz to 156.25 MHz depending on the protocol (PCIe uses 100 MHz, gigabit Ethernet uses 62.5 MHz or 125 MHz). Estimated jitter budget per Altera Stratix GX handbook: total TX jitter < 0.35 UI peak-to-peak at 3.125 Gbps with 8b/10b encoding. Use a dedicated PLL output for the reference clock buffer rather than a general-purpose clock pin, and route REFCLK as a 50-ohm SE controlled-impedance trace with no stubs.
Do not apply power to VCC before VCCIO is stable, or before MSEL configuration pins are tied to the correct mode-select value - this can cause high inrush on the I/O banks and trigger CMOS latch-up. Always configure unused transceivers to power-down mode (PCS reset, PMA in reset) via the Quartus II device options; leaving them in unknown state draws 30-50 mA per channel. Verify bitstream CRC after every configuration - the MSEL pins select the configuration scheme (Passive Serial, Passive Parallel, Fast Passive Parallel, JTAG), and a wrong MSEL setting causes silent configuration failure.
The FBGA-800 package has an estimated theta_JA of ~15 C/W with standard JEDEC JESD51-9 airflow of 200 LFM, but 8 active transceivers at 3.1875 Gbps can dissipate 1.5-2 W from the SERDES alone. Estimated total device power: 5-8 W typical for moderate logic utilization. Provide a thermal pad or thermal via array under the package center (4x4 via grid, 0.3 mm drill) and ensure the PCB has adequate copper area on top and inner layers for heat spreading.
Informations de conformité
RoHS compliance inferred from N suffix (lead-free finish). REACH, halogen-free, and conflict-mineral declarations were not located in the verified data. Not AEC-Q100 qualified (commercial-grade FPGA).
