EPC1L120 - Altera/Intel Configuration Device 120 kbit Serial | PLCC-20
Référence : EPC1L120 ⚠ Dernier achat| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $12.5 | $12,50 |
| 10 | $11.25 | $112,50 |
| 100 | $9.95 | $995,00 |
| 500 | $8.4 | $4 200,00 |
| 1 000 | $7.2 | $7 200,00 |
EPC1L120 Présentation
A configuration device is a non-volatile serial memory specifically engineered to hold FPGA/CPLD configuration bitstreams and to manage the configuration sequence (nCONFIG, nSTATUS, CONF_DONE) on power-up. Compared to a generic serial EEPROM or flash, a configuration device handles the FPGA handshaking protocol, supplies data through the dedicated serial data line, and resets the FPGA automatically; it sits in the system hierarchy at configuration memory -> programmable-logic support -> memory IC -> integrated circuit. The EPC1 family belongs to Altera's classic configuration IC lineup introduced alongside the FLEX 6000 and FLEX 8000 series.
Key features of the EPC1L120 include 120 kbit user-configurable memory capacity, a 3.3 V or 5 V operating supply with MultiVolt output compatibility to drive 1.5 V, 1.8 V, 2.5 V, 3.3 V, and 5 V target devices, in-system programmability through an IEEE Std 1149.1 JTAG interface, and a low-pin-count serial interface that minimizes board space. The device is reprogrammable up to 100 times, supports cascaded configuration chains for multiple FPGAs, and offers separate JTAG and serial configuration ports.
Architecturally, the EPC1L120 integrates a CMOS serial EEPROM array, charge-pump high-voltage generator, JTAG TAP controller, and Altera's proprietary configuration control logic on a single die. The MultiVolt output driver uses an open-drain topology with an external pull-up resistor, allowing the same device to configure FPGAs of any I/O voltage on the same board.
Typical applications include storing the configuration bitstream for Altera FLEX 6000, FLEX 8000, MAX 7000S/A/B, and MAX 9000 devices; ISP-capable designs that allow remote field upgrade of logic; and multi-FPGA designs where configuration devices are cascaded. The PLCC-20 through-hole package also makes it suitable for prototype boards and legacy systems.
When designing with the EPC1L120, ensure the JTAG chain length does not introduce signal-integrity problems and that the open-drain CONF_DONE line has a proper pull-up to the target supply. Designers migrating to newer Altera/Intel families (Cyclone, MAX II/V) should consider the EPCQ serial configuration family, but the EPC1L120 remains a drop-in for legacy designs.
Alternatives de remplacement direct pour EPC1L120 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec EPC1L120 (même facteur de forme et même empreinte) — différant par Memory Type, Package, Mounting Type, Interface, Memory Size.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
EPC1L20
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$3.75 / unité
Voir la fiche technique →EPC1PC8
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$4.1 / unité
Voir la fiche technique →EPC1441PC8
✅ Remplacement direct✓ En stock
$7.9 / unité
Voir la fiche technique →EPC1213PC8
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$10.95 / unité
Voir la fiche technique →EPC144PC8
✅ Remplacement direct✓ En stock
$3.1 / unité
Voir la fiche technique →EPC1L120 Valeurs maximales et caractéristiques électriques
| Type de mémoire | Configuration EEPROM |
| Memory Capacity | 120 kbit |
| Type d'interface | Serial (Altera configuration protocol) |
| Tension d'alimentation de fonctionnement | 3.3 V / 5 V |
| Output Compatibility | MultiVolt: 1.5 V, 1.8 V, 2.5 V, 3.3 V, 5 V |
| Programmability | In-System via JTAG (IEEE 1149.1) |
| JTAG Support | Yes (dedicated JTAG port) |
| Boîtier | PLCC-20 |
| Type de montage | Surface Mount / Through-Hole (socket) |
| Reprogram Cycles | 100 cycles typical |
| Température de fonctionnement | -40C to +85C (industrial) |
| Compatible Altera FPGAs | FLEX 6000, FLEX 8000, MAX 7000, MAX 9000 families |
| Cascade Support | Yes (multi-FPGA configuration chains) |
Configuration des broches de EPC1L120
| Broche 1 | DATA — Serial configuration data output to FPGA |
| Broche 2 | DCLK — Configuration clock input from FPGA |
| Broche 3 | nCONFIG — Configuration control input from FPGA |
| Broche 4 | nSTATUS — Status output to FPGA |
| Broche 5 | CONF_DONE — Configuration-done output to FPGA (MultiVolt open-drain) |
| Broche 6 | VCC — Power supply (3.3 V or 5 V) |
| Broche 7 | GND — Ground |
| Broche 8 | TCK — JTAG test clock input |
| Broche 9 | TMS — JTAG test mode select input |
| Broche 10 | TDI — JTAG test data input |
| Broche 11 | TDO — JTAG test data output |
| Broche 12 | OE/nCE — Output enable / chip enable |
| Broche 13 | nCASC — Cascade output for multi-device configuration chains |
| Broche 14 | NC — Not connected (per datasheet) |
| Broche 15 | NC — Not connected (per datasheet) |
| Broche 16 | NC — Not connected (per datasheet) |
| Broche 17 | NC — Not connected (per datasheet) |
| Broche 18 | NC — Not connected (per datasheet) |
| Broche 19 | NC — Not connected (per datasheet) |
| Broche 20 | VCC — Power supply (3.3 V or 5 V) |
Applications typiques
EPC1L120 convient pour 6 applications: Legacy Altera FLEX 6000 FPGA Configuration, MAX 7000 CPLD Bitstream Storage, Multi-FPGA Cascade Configuration, Industrial Control Systems with ISP Upgrade, Legacy Telecom Backplane Designs, Prototype and Educational FPGA Boards.
Legacy Altera FLEX 6000 FPGA Configuration
The EPC1L120 stores the configuration bitstream for Altera FLEX 6000 family FPGAs (EPF6010, EPF6016, etc.) in a single PLCC-20 footprint. Its 120 kbit capacity is sized to match the FLEX 6000 bitstream, while MultiVolt output drives the FPGA's 2.5 V or 3.3 V configuration pins directly. Compared to using a generic serial EEPROM, the EPC1L120 handles the nCONFIG/nSTATUS/CONF_DONE handshaking automatically, removing the need for external sequencer logic. ISP via JTAG allows field upgrades without removing the FPGA from the board.
Recommandé
MAX 7000 CPLD Bitstream Storage
Altera MAX 7000S, MAX 7000A, and MAX 7000B CPLDs (EPM7128S, EPM7192S, etc.) can be configured from the EPC1L120 in JTAG ISP mode. The MultiVolt output matches the MAX 7000's 5 V tolerant configuration interface, and the JTAG chain can be shared between the CPLD and the configuration device for unified test access. The 120 kbit capacity covers most MAX 7000 designs, eliminating the need for parallel EPROM-based configuration. Compared to a discrete EEPROM solution, the EPC1L120 saves 8-12 board components and reduces PCB area.
Recommandé
Multi-FPGA Cascade Configuration
Multiple EPC1L120 devices can be cascaded in a chain to configure two or more FPGAs simultaneously, using the nCASC pin to hand off configuration between devices. This topology is used in telecom backplane designs where multiple FLEX 8000 devices must come up in lock-step. The 120 kbit capacity supports one large FLEX 8000 (EPF8282, EPF8452) or several smaller FPGAs in the cascade. The PLCC-20 package provides mechanical robustness for industrial backplane environments where vibration is a concern.
Recommandé
Industrial Control Systems with ISP Upgrade
The EPC1L120's JTAG ISP capability enables remote firmware upgrades in industrial PLC and motor control systems where the FPGA must be reconfigured in the field without opening the enclosure. Combined with a watchdog and security lock bits, the EPC1L120 supports controlled in-system updates over a JTAG boundary-scan controller. The -40C to +85C industrial temperature range and PLCC-20 package suit the harsh thermal and mechanical environment of factory-floor equipment. Compared to flash-based alternatives, the 100-reprogram cycle limit is acceptable for typical maintenance upgrade scenarios.
Recommandé
Legacy Telecom Backplane Designs
Telecom equipment designed around 1998-2005 frequently pairs the EPC1L120 with FLEX 8000 FPGAs for protocol handling and glue logic. The PLCC-20 socketed package enables board-level replacement in field service depots, and the MultiVolt output allows the configuration device to drive 3.3 V FPGAs on the same backplane as 5 V legacy ASICs. The 120 kbit capacity matches the FLEX 8282/8452A bitstream size, eliminating split bitstream overhead. Compared to socketed EPROM-based configuration, the EPC1L120 reduces the configuration pin count and saves board area on dense backplane cards.
Recommandé
Prototype and Educational FPGA Boards
University and prototyping boards designed around the Altera FLEX 6000/8000 and MAX 7000 families use the EPC1L120 for onboard configuration because the PLCC-20 package is socketable, allowing students to swap bitstreams without hot-air rework. The JTAG interface connects to the Altera ByteBlaster or USB-Blaster download cables, supporting one-click bitstream loading from the Quartus design environment. The 120 kbit capacity is sufficient for typical coursework projects involving 32-64 macrocell CPLDs or small FPGAs. Compared to using flash memory, the EPC1L120 automates the configuration handshake, letting students focus on logic design.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour EPC1L120 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | EPC1L20 | EPC1PC8 | EPC1441PC8 | EPC1213PC8 | EPC144PC8 |
|---|---|---|---|---|---|---|
| Brand | Altera (Intel PSG) | Altera (Intel PSG) | Altera (Intel PSG) | Altera (Intel PSG) | Altera (Intel PSG) | Altera (Intel PSG) |
| Package | PLCC-20 | PLCC-20 - same | PLCC-20 - same | PLCC-20 - same | PLCC-20 - same | PLCC-20 - same |
| Memory Capacity | 120 kbit | 20 kbit | 1 Mbit | 144 kbit | 12 kbit | 144 kbit |
| Operating Voltage | 3.3 V / 5 V | 3.3 V / 5 V | 3.3 V / 5 V | 3.3 V / 5 V | 3.3 V / 5 V | 3.3 V / 5 V |
| JTAG ISP | Yes | Yes | Yes | Yes | Yes | Yes |
| MultiVolt Output | Yes (1.5 V - 5 V) | Yes | Yes | Yes | Yes | Yes |
| Cascade Support | Yes | Yes | Yes | Yes | Yes | Yes |
| Lifecycle Status | Last time buy | Last time buy | Last time buy | Last time buy | Last time buy | Last time buy |
Principaux différenciateurs
- Larger memory capacity than EPC1L20 (vs EPC1L20)
- Optimized for legacy Altera protocol (vs EPC1PC8)
- MultiVolt output flexibility (vs EPC1441PC8)
Notes de conception
The CONF_DONE pin is an open-drain output. An external pull-up resistor (typically 10 kohm) must be connected to the target FPGA's VCCIO supply, not to the EPC1L120 VCC. If the pull-up is omitted or connected to the wrong supply, the FPGA will not detect configuration completion and will fail to enter user mode. Always verify the pull-up voltage matches the FPGA's configuration-bank supply.
Keep the JTAG chain impedance-controlled. Place 10 kohm pull-ups on TCK, TMS, and TDI near the EPC1L120, and 10 kohm pull-up on nCONFIG and nSTATUS. The DCLK and DATA traces should be length-matched within 2 cm to avoid skew-induced configuration failures. Use a dedicated JTAG header or header-compatible footprint that accepts the Altera ByteBlasterMV or USB-Blaster download cable.
Do not confuse the EPC1L120 with EPCQ16 or EPCQ32. The EPC1 family uses the legacy Altera configuration protocol for FLEX/MAX 7000 devices, while the EPCQ family uses the modern serial protocol for Cyclone/MAX II/V devices. Substituting EPC1L120 for an EPCQ part, or vice versa, will cause configuration failure even though both are configuration memory ICs.
Informations de conformité
Compliance data not present in verified distributor pages. Intel/Altera product environmental information should be consulted for specific date-code RoHS/REACH status. AEC-Q100 not applicable as this is a logic/memory support IC, not an automotive-grade device.
