IS61WV102416DBLL-10TLI - 16Mb Async SRAM 1Mx16 10ns | ISSI
Référence : IS61WV102416DBLL-10TLI ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $5.2 | $5,20 |
| 10 | $4.62 | $46,20 |
| 100 | $4.05 | $405,00 |
| 500 | $3.61 | $1 805,00 |
| 1 000 | $3.18 | $3 180,00 |
IS61WV102416DBLL-10TLI Présentation
Asynchronous static RAM (SRAM) is a volatile memory technology that retains data as long as power is applied, without the refresh cycles required by DRAM. Within the broader memory hierarchy, SRAM sits closest to the processor because of its sub-15 ns access times; it is used for cache, look-up tables, scratch-pad buffers, and FIFO storage in networking, industrial, and embedded systems. Compared with synchronous SRAM (such as QDR or DDR SRAM), asynchronous SRAM uses simple chip-enable, output-enable, and write-enable control signals and is ideal for glue-less processor bus interfaces.
The IS61WV102416DBLL-10TLI provides fully static operation (no clock required), TTL-compatible I/O levels, common data-in/data-out bus architecture, and an active-low output enable for bus sharing. Power consumption is minimized through a Chip Enable power-down mode, and the device supports industrial temperature range operation. The CMOS fabrication process delivers high noise immunity and low standby current, both of which are critical for battery-backed or energy-conscious designs.
Typical applications include industrial controllers, networking line cards, routers and switches requiring fast look-up tables, automotive telematics (non-safety-critical subsystems), medical instrumentation buffers, RAID controllers, and any embedded CPU/MCU design that needs a large, low-latency external data store beyond the on-chip SRAM budget. The wide word width (x16) is well matched to 16-bit and 32-bit microcontrollers and DSPs.
When designing with this device, keep in mind that asynchronous SRAM bandwidth is limited by the controller's ability to issue back-to-back read or write strobes, so the 10 ns access time implies roughly 100 MHz equivalent single-transfer throughput per cycle. Decoupling and signal routing must be handled carefully on long busloads to maximize margin.
This page synthesizes distributor pricing, drop-in alternative cross-references, and practical design notes that go beyond the manufacturer datasheet to help engineers evaluate and qualify the part quickly.
Alternatives de remplacement direct pour IS61WV102416DBLL-10TLI — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
IS61WV102416DBLL-10TLI-TR
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
IS61WV102416DALL-10TLI
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
IS61WV102416BLL-10TLI
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
AS7C31016B-10TIN
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
CY7C1061AV33-10ZXI
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
IS61WV102416DBLL-10TLI Valeurs maximales et caractéristiques électriques
| Type de mémoire | Asynchronous SRAM (Static RAM) |
| Memory Organization | 1M words x 16 bits |
| Memory Density | 16 Mbit (2 MB) |
| Supply Voltage (VCC) | 2.4 V to 3.6 V (3.3 V nominal) |
| Access Time | 10 ns |
| Type d'interface | Parallel, asynchronous |
| Bus Width | 16 bits |
| Température de fonctionnement | -40 C to +85 C (Industrial) |
| Boîtier | 48-pin TSOP-I |
| Type de montage | Surface Mount |
| I/O Levels | TTL-compatible |
| Output Enable | Yes, active-low (OE-bar) |
| Chip Enable | Yes, active-low (CE-bar / CE1, CE2) |
| Write Enable | Yes, active-low (WE-bar) |
| Operating Mode | Fully static, no clock required |
| Statut RoHS | Compliant |
| Niveau MSL | 3 (per JEDEC J-STD-020) |
Configuration des broches de IS61WV102416DBLL-10TLI
| Broche 1 | NC — Not connected (per datasheet) |
| Broche 2 | NC — Not connected (per datasheet) |
| Broche 3 | NC — Not connected (per datasheet) |
| Broche 4 | A19 — Address input 19 |
| Broche 5 | A18 — Address input 18 |
| Broche 6 | A17 — Address input 17 |
| Broche 7 | A16 — Address input 16 |
| Broche 8 | A15 — Address input 15 |
| Broche 9 | A14 — Address input 14 |
| Broche 10 | A13 — Address input 13 |
| Broche 11 | A12 — Address input 12 |
| Broche 12 | OE-bar — Output Enable (active low) |
| Broche 13 | UB-bar — Upper Byte Enable (active low) |
| Broche 14 | LB-bar — Lower Byte Enable (active low) |
| Broche 15 | I/O15 — Data I/O 15 |
| Broche 16 | I/O14 — Data I/O 14 |
| Broche 17 | I/O13 — Data I/O 13 |
| Broche 18 | I/O12 — Data I/O 12 |
| Broche 19 | I/O11 — Data I/O 11 |
| Broche 20 | I/O10 — Data I/O 10 |
| Broche 21 | I/O9 — Data I/O 9 |
| Broche 22 | I/O8 — Data I/O 8 |
| Broche 23 | VCC — Power supply (2.4 V to 3.6 V) |
| Broche 24 | VSS — Ground |
| Broche 25 | I/O7 — Data I/O 7 |
| Broche 26 | I/O6 — Data I/O 6 |
| Broche 27 | I/O5 — Data I/O 5 |
| Broche 28 | I/O4 — Data I/O 4 |
| Broche 29 | I/O3 — Data I/O 3 |
| Broche 30 | I/O2 — Data I/O 2 |
| Broche 31 | I/O1 — Data I/O 1 |
| Broche 32 | I/O0 — Data I/O 0 |
| Broche 33 | CE1-bar — Chip Enable 1 (active low) |
| Broche 34 | CE2 — Chip Enable 2 (active high) |
| Broche 35 | A0 — Address input 0 |
| Broche 36 | A1 — Address input 1 |
| Broche 37 | A2 — Address input 2 |
| Broche 38 | A3 — Address input 3 |
| Broche 39 | A4 — Address input 4 |
| Broche 40 | A5 — Address input 5 |
| Broche 41 | A6 — Address input 6 |
| Broche 42 | A7 — Address input 7 |
| Broche 43 | A8 — Address input 8 |
| Broche 44 | A9 — Address input 9 |
| Broche 45 | A10 — Address input 10 |
| Broche 46 | A11 — Address input 11 |
| Broche 47 | WE-bar — Write Enable (active low) |
| Broche 48 | VSS — Ground |
Applications typiques
IS61WV102416DBLL-10TLI convient pour 6 applications: Industrial Controller Scratch-Pad Memory, Networking Router / Switch Look-Up Table, Automotive Infotainment / Telematics Buffer, Medical Instrumentation Data Buffer, RAID Controller Cache Memory, Embedded CPU/MCU External Data Store.
Industrial Controller Scratch-Pad Memory
The IS61WV102416DBLL-10TLI provides a 2 MB asynchronous SRAM scratch pad for industrial PLCs, HMI panels, and motion controllers. The 10 ns access time and 1M x 16 organization give 16-bit MCUs and DSPs a deterministic, glue-less external memory that needs no controller overhead. Operating from 2.4-3.6 V it tolerates loosely regulated 24 V->3.3 V rails common in industrial racks, and the industrial -40C to +85C temperature range ensures reliable operation on factory floors.
Recommandé
Networking Router / Switch Look-Up Table
In routers, switches, and firewalls the IS61WV102416DBLL-10TLI is used as a fast parallel look-up table for routing entries, ACL tables, and packet buffers. The 10 ns access time supports line-rate look-ups at typical 100 MHz forwarding clock, and the 16-bit bus aligns with standard network processor datapaths. The wide 2.4-3.6 V supply range simplifies power tree design across router line cards.
Recommandé
Automotive Infotainment / Telematics Buffer
The IS61WV102416DBLL-10TLI serves as a fast external buffer for automotive infotainment head units and telematics control units (non-safety-critical subsystems). The 1M x 16 organization provides ample scratch space for navigation maps, audio DSP delay lines, and CAN/LIN gateway buffers. The wide operating voltage eases integration into 12 V automotive battery rails with linear regulation, and the industrial temperature range covers in-cabin environments.
Recommandé
Medical Instrumentation Data Buffer
In ultrasound carts, patient monitoring stations, and portable diagnostic devices, the IS61WV102416DBLL-10TLI acts as a high-speed FIFO between the analog front end and the host DSP. The 10 ns access time keeps up with high-sample-rate ADCs, while the 16-bit bus matches typical medical imaging pipelines. Low standby current and TTL-compatible I/O simplify battery-powered handheld instrument designs.
Recommandé
RAID Controller Cache Memory
RAID controllers use asynchronous SRAM as a write-back cache to absorb burst writes from the host before draining to disk. The IS61WV102416DBLL-10TLI's 10 ns access time and 1M x 16 organization give 2 MB of low-latency cache that fits typical small-RAID or SSD controller architectures. The 48-pin TSOP-I footprint simplifies board layout next to SATA/SAS controller ASICs.
Recommandé
Embedded CPU/MCU External Data Store
Many 16-bit and 32-bit MCUs ship with only a few hundred KB of internal RAM, insufficient for buffering sensor streams or graphics frame data. The IS61WV102416DBLL-10TLI provides 2 MB of external storage with a simple asynchronous bus interface - no SDRAM controller, no refresh cycles. It pairs directly with the external memory bus of most Cortex-M, RX, and dsPIC devices, freeing the internal SRAM for deterministic real-time tasks.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour IS61WV102416DBLL-10TLI — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | IS61WV102416DBLL-10TLI-TR | IS61WV102416DALL-10TLI | IS61WV102416BLL-10TLI | AS7C31016B-10TIN | CY7C1061AV33-10ZXI |
|---|---|---|---|---|---|---|
| Package | 48-pin TSOP-I | 48-pin TSOP-I | 48-pin TSOP-I | 48-pin TSOP-I | 48-pin TSOP-I | 54-pin TSOP-II |
| Brand | ISSI | ISSI | ISSI | ISSI | Alliance Memory | Infineon (formerly Cypress) |
| Memory Density | 16 Mbit (2 MB) | 16 Mbit | 16 Mbit | 16 Mbit | 16 Mbit | 16 Mbit |
| Organization | 1M x 16 | 1M x 16 | 1M x 16 | 1M x 16 | 1M x 16 | 1M x 16 |
| Access Time | 10 ns | 10 ns | 10 ns | 10 ns | 10 ns | 10 ns |
| Supply Voltage | 2.4 V to 3.6 V (D variant) | 2.4 V to 3.6 V | 2.4 V to 3.6 V | 3.3 V +/- 0.3 V | 3.3 V +/- 0.3 V | 3.3 V +/- 0.3 V |
| Interface | Asynchronous Parallel | Asynchronous Parallel | Asynchronous Parallel | Asynchronous Parallel | Asynchronous Parallel | Asynchronous Parallel |
| Operating Temperature | -40 C to +85 C (Industrial) | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
Principaux différenciateurs
- Wide 2.4 V to 3.6 V supply supports loosely regulated rails (vs IS61WV102416BLL-10TLI (3.3 V +/- 0.3 V))
- Same 48-pin TSOP-I pinout across ISSI family for PCB reuse (vs CY7C1061AV33-10ZXI (54-pin TSOP-II))
- Industrial -40C to +85C temperature range standard (vs Consumer-grade 0C to +70C SRAM)
Notes de conception
Route address and data buses with matched trace lengths and 50 ohm controlled impedance on the 48-pin TSOP-I footprint. Place at least one 0.1 uF ceramic decoupling capacitor close to each VCC pin (pin 23) and a bulk 10 uF tantalum or ceramic capacitor near the package. The wide 16-bit bus is sensitive to skew; avoid running address lines parallel to noisy clock or switching-power traces for more than 25 mm.
Do not leave Chip Enable (CE1-bar) floating. CE1-bar must be driven low during the access cycle; a floating CE can cause the device to enter an undefined state and draw elevated supply current. Similarly, UB-bar and LB-bar must be tied to GND when byte-write control is not used, otherwise I/O bus contention can occur. According to the ISSI datasheet, OE-bar should never be asserted before CE1-bar goes active.
Active supply current scales with read/write frequency. Estimated: at 10 ns cycle (100 MHz equivalent) the IS61WV102416DBLL-10TLI typically draws 90-110 mA active, but in standby (CE1-bar high) it drops below 5 mA. Use chip-enable power-down aggressively in battery-backed designs: gate CE1-bar with the host MCU's chip-select to achieve >90% current reduction during idle periods.
Because asynchronous SRAM relies on address-to-data timing rather than a clock, hold and setup margins must be validated across voltage and temperature. According to the ISSI datasheet, output hold time after OE-bar rising edge is at least 2 ns; designers should sample data on the rising edge of OE-bar (or equivalent strobe) and add 1-2 ns of margin in production test to absorb process variation at the temperature corners.
Informations de conformité
RoHS compliant per ISSI product page. MSL Level 3 per JEDEC J-STD-020. Not AEC-Q100 qualified; not recommended for automotive safety-critical applications.
