TPS82140SILR - 17V 2A Step-Down MicroSiP Module | Texas Instruments
Référence : TPS82140SILR ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $4.32 | $4,32 |
| 10 | $3.88 | $38,80 |
| 100 | $3.45 | $345,00 |
| 500 | $3.05 | $1 525,00 |
| 1 000 | $2.72 | $2 720,00 |
| 3 000 | $2.45 | $7 350,00 |
TPS82140SILR Présentation
A step-down (buck) converter is a switch-mode power supply topology that efficiently steps a higher DC input voltage down to a lower DC output voltage by rapidly switching an inductor and rectifying the stored energy. The TPS82140 integrates the synchronous power stage, the shielded inductor, and the compensation network into one MicroSiP package, eliminating external magnetics design and shrinking PCB area by roughly 60% compared to discrete buck implementations. As part of the broader power-management IC hierarchy, it sits between discrete switching regulators and fully discrete buck converters.
Key specifications include 2A continuous output current, 0.9V to 6V adjustable output voltage, 3V to 17V input voltage range, 17V maximum input, 2 MHz typical switching frequency, 20 uA quiescent current, and 1% feedback voltage accuracy. The TPS82140 operates from -40C to +125C junction temperature and includes internal soft-start, thermal shutdown, and a power-good indicator. The integrated inductor shields against radiated EMI and removes the need for a separate inductor selection.
Typical applications include industrial 12V and 24V bus point-of-load rails, portable and battery-powered equipment, communication infrastructure modules, factory automation nodes, and space-constrained consumer devices. The wide 17V input rating makes it especially suitable for industrial sensors and 12V supply rails.
When designing with this device, follow the manufacturer recommended input and output capacitor values and keep the input capacitor loop area minimal. The MicroSiP package dissipates heat primarily through the PCB copper pads; ensure adequate copper area on top and inner layers for thermal relief.
This page synthesizes distributor pricing, drop-in pin-compatible alternatives, design notes, and application guidance not found in the TI datasheet alone.
Alternatives de remplacement direct pour TPS82140SILR — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec TPS82140SILR (même facteur de forme et même empreinte) — différant par Output Voltage Range, Package, Input Voltage Range, Topology, Continuous Output Current.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
TPS82140SILT
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
TPS82130SILR
✅ Remplacement direct✓ En stock
$2.18 / unité
Voir la fiche technique →TPS82150SILR
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
TPS82130SILT
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
TPS82150SILT
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
TPS82140SILR Valeurs maximales et caractéristiques électriques
| Topologie | Synchronous Buck (Step-Down) |
| Plage de tension d'entrée | 3 V to 17 V |
| Plage de tension de sortie | 0.9 V to 6 V (adjustable) |
| Continuous Output Current | 2 A |
| Fréquence de commutation | 2 MHz (typical) |
| Courant de repos | 20 uA |
| Feedback Voltage Accuracy | 1% (typical) |
| Control Topology | DCS-Control |
| Light Load Behavior | Power Save Mode |
| Boîtier | MicroSiP uSIP-8 (SIL) 3.0 x 2.8 x 1.5 mm |
| Integrated Inductor | Yes (shielded) |
| Température de fonctionnement | -40 C to +125 C |
| Type de montage | Surface Mount |
| Niveau MSL | 2 |
| Statut RoHS | Compliant |
| Caractéristiques | Power Good, Soft Start, Thermal Shutdown |
Configuration des broches de TPS82140SILR
| Broche 1 | VIN — Input voltage supply (3V to 17V) |
| Broche 2 | GND — Power ground |
| Broche 3 | EN — Enable (active high) |
| Broche 4 | PG — Power Good output |
| Broche 5 | FB — Feedback (to VOUT resistor divider) |
| Broche 6 | VOS — Output voltage sense / bootstrap |
| Broche 7 | SW — Switch node (internal, integrated inductor) |
| Broche 8 | AGND — Analog ground |
Applications typiques
TPS82140SILR convient pour 6 applications: Industrial 12V/24V Point-of-Load Rails, Portable and Battery-Powered Equipment, Communication Infrastructure Modules, Factory Automation Nodes, Space-Constrained Consumer Electronics, Test and Measurement Instrumentation.
Industrial 12V/24V Point-of-Load Rails
The TPS82140SILR's 17V maximum input rating comfortably handles 12V industrial buses with margin for transients, while its integrated inductor shields against EMI in factory environments. The 2A continuous output and 0.9-6V adjustable range cover most logic rails (1.0V, 1.2V, 1.8V, 2.5V, 3.3V, 5V) found on industrial sensor boards, PLC I/O modules, and HMI controllers. DCS-Control topology ensures fast transient response when motors or solenoids cause sudden load steps on the 12V rail. The MicroSiP 3.0 x 2.8 mm footprint fits inside small sensor housings where a discrete buck would not. Power Save Mode lowers quiescent current to 20 uA, suitable for always-on industrial nodes.
Recommandé
Portable and Battery-Powered Equipment
The TPS82140SILR's 20 uA quiescent current and Power Save Mode extend battery life in handheld instruments, portable medical devices, and wireless sensor nodes. Its 3V minimum input supports direct connection to single-cell Li-ion batteries or 3.3V system rails. The 2 MHz switching frequency stays above the AM band, preventing interference with wireless radios. The MicroSiP package is only 1.5 mm tall, fitting inside slim handheld enclosures. With 2A output capability, the module can power a microcontroller, display, and wireless radio simultaneously without external magnetics design. The wide -40C to +125C operating range also supports outdoor field equipment.
Recommandé
Communication Infrastructure Modules
The TPS82140SILR delivers clean 1.8V or 3.3V rails for FPGAs, ASICs, and SerDes devices in small-form-factor communication modules such as SFP, PoE, and industrial Ethernet cards. The integrated inductor shields against radiated EMI, which is critical in dense PCB layouts where a discrete buck's magnetic field could couple into adjacent traces. The 2A output current is sufficient for powering transceiver rails in 1G/2.5G Ethernet PHYs. Power Good output enables sequencing with downstream regulators. The compact MicroSiP footprint frees board area for magnetics and connectors in compact modules.
Recommandé
Factory Automation Nodes
The TPS82140SILR's wide 3V to 17V input allows direct operation from 24V industrial backplanes while still producing 5V or 3.3V logic rails for sensor nodes, IO-Link masters, and fieldbus interfaces. DCS-Control topology handles load transients caused by relay coils and motor starters on the same 24V bus. The integrated MicroSiP inductor reduces BOM count by approximately 8 components versus a discrete buck, lowering assembly cost for high-volume automation hardware. The -40C to +125C junction rating covers harsh factory environments with elevated ambient temperatures.
Recommandé
Space-Constrained Consumer Electronics
The TPS82140SILR's MicroSiP package is only 3.0 mm x 2.8 mm x 1.5 mm tall, enabling compact step-down conversion in smart-home hubs, wearables, audio accessories, and IoT gateways. The integrated inductor eliminates the need for a separate inductor component, freeing roughly 20-30 mm^2 of board area. The 2A output current handles MCU + wireless + audio loads, while Power Save Mode keeps standby current low for always-connected devices. The 17V input also supports USB-PD or 12V adapter inputs in compact consumer enclosures.
Recommandé
Test and Measurement Instrumentation
The TPS82140SILR produces low-ripple, low-noise rails for precision analog front-ends, ADC references, and signal conditioning circuits in bench-top instruments. While a switching regulator adds some ripple compared to an LDO, the 2 MHz switching frequency and DCS-Control keep output ripple below 1% in most conditions. The 2A output supports combined analog + digital loads on a single board. Power Good output enables synchronised startup with sensitive analog blocks. The MicroSiP package suits the dense mixed-signal layouts typical of oscilloscope and DMM front-end boards.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour TPS82140SILR — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | TPS82140SILT | TPS82130SILR | TPS82150SILR | TPS82130SILT | TPS82150SILT |
|---|---|---|---|---|---|---|
| Package | uSIP-8 (SIL) MicroSiP 3.0x2.8x1.5 mm | uSIP-8 (SIL) MicroSiP - same | uSIP-8 (SIL) MicroSiP - same | uSIP-8 (SIL) MicroSiP - same | uSIP-8 (SIL) MicroSiP - same | uSIP-8 (SIL) MicroSiP - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Output Current | 2 A | 2 A | 1 A | 3 A | 1 A | 3 A |
| Input Voltage Range | 3 V to 17 V | 3 V to 17 V | 3 V to 17 V | 3 V to 17 V | 3 V to 17 V | 3 V to 17 V |
| Output Voltage Range | 0.9 V to 6 V | 0.9 V to 6 V | 0.9 V to 6 V | 0.9 V to 6 V | 0.9 V to 6 V | 0.9 V to 6 V |
| Switching Frequency | 2 MHz | 2 MHz | 2 MHz | 2 MHz | 2 MHz | 2 MHz |
| Quiescent Current | 20 uA | 20 uA | 20 uA | 20 uA | 20 uA | 20 uA |
| Topology | DCS-Control, synchronous buck | DCS-Control, synchronous buck | DCS-Control, synchronous buck | DCS-Control, synchronous buck | DCS-Control, synchronous buck | DCS-Control, synchronous buck |
| Integrated Inductor | Yes (shielded) | Yes (shielded) | Yes (shielded) | Yes (shielded) | Yes (shielded) | Yes (shielded) |
Principaux différenciateurs
- 2A output in 1.5 mm tall MicroSiP with integrated shielded inductor (vs TPS82130SILR)
- Lower output current with same BOM simplicity vs TPS82150 (vs TPS82150SILR)
- Wide 17V input handles industrial 24V bus transients after protection (vs TPS82130SILR / TPS82150SILR)
Notes de conception
The TPS82140 MicroSiP package dissipates heat primarily through the PCB copper pads beneath and around the module. Provide at least 25 mm^2 of copper pour on the top layer connected to the VIN, GND, and SW pads, plus thermal vias to inner ground planes. Without adequate copper area, full 2A operation may require derating in high-ambient-temperature environments above 85C. The input capacitor loop area should be minimized by placing the input bypass capacitor as close to the VIN and GND pads as possible to reduce switching noise injection back into the input rail.
Do not exceed 17V on the VIN pin even transiently, as the device has no internal over-voltage protection. Ensure the upstream supply's transient response stays below 17V under all load-dump conditions. Also, do not leave the FB pin floating; the converter requires a feedback resistor divider tied to VOUT for proper regulation. The EN pin should be tied to VIN (through a resistor) for always-on operation, or driven by a logic signal for sequenced power-up.
Keep the feedback trace short and away from the SW node and the integrated inductor to avoid noise coupling. Place the feedback resistor divider close to the FB pin. Route the VOS sense trace directly to the output capacitor to minimize output voltage offset. The PG pin can be left floating if power-good monitoring is not required. For EMI-sensitive designs, add a small ferrite bead on the input if conducted emissions must meet strict CISPR standards.
Informations de conformité
RoHS compliant per TI product page. Industrial-grade (not AEC-Q100 qualified); -40C to +125C operating junction range.
