PIC32MX775F256LT-80I/BG - 80MHz 32-bit MCU 256KB Flash | Microchip
MPN: PIC32MX775F256LT-80I/BG ✓ פעילPIC32MX775F256LT-80I/BG סקירה
A 32-bit microcontroller (MCU) is a programmable processor with on-chip Flash program storage, SRAM data memory, and integrated peripherals such as timers, ADC, communication controllers and DMA. Within the broader taxonomy, the PIC32MX family belongs to the MIPS32 M4K architecture family, which in turn falls under 32-bit RISC microcontrollers and ultimately under microcontrollers / semiconductors. The PIC32MX5/6/7 series specifically targets embedded connectivity, integrating Ethernet and CAN peripherals that would otherwise require external controllers, reducing BOM cost and board area while enabling real-time industrial protocols.
Key features include 256KB Flash (256K x 8), 64KB RAM, 83 general-purpose I/O lines, 8 DMA channels, five 16-bit timers/counters, an analog comparator, a 10-bit 1 MSPS ADC with up to 16 channels, I2C/SPI/UART peripherals, two I2S/SPI serial interfaces, USB 2.0 Full-Speed OTG, two CAN 2.0b modules, 10/100 Ethernet MAC with MII/RMII interfaces, and an RTCC. The 121-ball TFBGA package provides a compact 10x10 mm footprint at 0.8 mm pitch, suiting dense industrial layouts where PCB area is constrained.
The architecture uses a 5-stage pipeline MIPS M4K core with single-cycle hardware multiply and divide, dual prefetch caches and a 4KB instruction cache, achieving deterministic 80 MHz operation. Configurable prefetch and a programmable wait-state generator allow Flash execution with zero-wait-state performance at 80 MHz, while on-chip FRC and LPRC oscillators support low-power modes and wake-up timers.
Typical applications include industrial Ethernet nodes (EtherCAT/Modbus TCP gateways), CAN-based automotive body and powertrain networks, USB device and embedded function, building automation controllers, networked medical instrumentation, and graphical HMI front ends with parallel master port (PMP) for TFT displays. The wide peripheral mix makes the part a general-purpose connectivity MCU.
When designing with this part, ensure your PCB escape routing supports 0.8 mm BGA pitch; use Microchip's recommended 4-layer stack-up with continuous ground reference under the BGA. Plan for proper decoupling (0.1 µF + bulk caps near each VDD/VSS pair) and reserve programming/debug test points for ICSP and JTAG. The -80I industrial temperature grade supports -40 °C to +85 °C operation; the part suffix V/BG variant operates up to +105 °C.
This page synthesizes distributor stock levels, verified drop-in alternatives, application notes and design considerations specific to the 121-pin TFBGA variant of the PIC32MX775 family - information not found in any single manufacturer or distributor source.
חלופות תחליף ישיר עבור PIC32MX775F256LT-80I/BG — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם PIC32MX775F256LT-80I/BG (אותו גורם צורה וטביעת רגל) — שונים ב ADC, USB, Package, CAN, Timers.
PIC32MX775F256L-80I/BG
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←PIC32MX675F256LT-80I/BG
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←PIC32MX575F256LT-80I/BG
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←PIC32MX764F128LT-I/BG
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←PIC32MX695F512L-80I/BG
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←PIC32MX360F256LT-80I/BG
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←PIC32MX775F256LT-80I/BG דירוגים מרביים ומאפיינים חשמליים
| Core Processor | MIPS32 M4K |
| Core Size | 32-Bit |
| Core Speed | 80 MHz |
| Program Memory Type | Flash |
| Program Memory Size | 256 KB (256K x 8) |
| RAM Size | 64 KB (64K x 8) |
| Supply Voltage (VDD) | 2.3 V to 3.6 V |
| I/O Pins | 83 |
| DMA Channels | 8 |
| Timers | 5 x 16-bit |
| ADC | 10-bit, 1 MSPS, up to 16 channels |
| Communication Interfaces | USB 2.0 OTG, 2x CAN 2.0b, 10/100 Ethernet MAC, 2x I2C, 2x SPI, 2x UART, 2x I2S |
| טמפרטורת פעולה | -40 °C to +85 °C (industrial -80I grade) |
| מארז | 121-pin TFBGA (10x10 mm, 0.8 mm pitch) |
| סוג הרכבה | Surface Mount |
| סטטוס RoHS | Compliant (Lead-free, BG suffix) |
| רמת MSL | 3 |
| Lead-Free / Halogen-Free | Yes / Yes (per BG suffix) |
תצורת פינים של PIC32MX775F256LT-80I/BG
| פין A1 | VSS — Ground reference |
| פין A12 | VDD — Core digital supply 2.3-3.6V |
| פין B1 | RGMDC1/RD11 — PMP data / GPIO |
| פין B12 | VDD — Core digital supply 2.3-3.6V |
| פין C1 | RGMDC2/RD10 — PMP data / GPIO |
| פין C12 | VSS — Ground |
| פין D1 | RGMID0/RD9 — PMP data / GPIO |
| פין D12 | RGMD1/RE5 — PMP data / GPIO |
| פין E1 | RGMID1/RD8 — PMP data / GPIO |
| פין E12 | RGMD0/RE4 — PMP data / GPIO |
| פין F1 | RGMD3/RD3 — PMP data / GPIO |
| פין F12 | RGMD2/RD2 — PMP data / GPIO |
| פין G1 | RGMD5/RD1 — PMP data / GPIO |
| פין G12 | RGMD4/RD0 — PMP data / GPIO |
| פין H1 | RGMD7/RD5 — PMP data / GPIO |
| פין H12 | RGMD6/RD4 — PMP data / GPIO |
| פין J1 | RGMEN1/RF8 — PMP enable / GPIO |
| פין J12 | RGMEN0/RF7 — PMP enable / GPIO |
| פין K1 | AN0/RPB0 — Analog input / GPIO port B |
| פין K12 | AN1/RPB1 — Analog input / GPIO port B |
| פין L1 | AN2/RPB2 — Analog input / GPIO port B |
| פין L12 | AN3/RPB3 — Analog input / GPIO port B |
| פין M1 | AN4/RPB4 — Analog input / GPIO port B |
| פין M12 | AN5/RPB5 — Analog input / GPIO port B |
| פין N1 | VREF-/CVREF-/RA9 — ADC negative reference |
| פין N12 | VREF+/CVREF+/RA10 — ADC positive reference |
| פין P1 | AN6/RB6 — Analog input / GPIO port B |
| פין P12 | AN7/RB7 — Analog input / GPIO port B |
| פין R1 | AN8/RB8 — Analog input / GPIO port B |
| פין R12 | AN9/RB9 — Analog input / GPIO port B |
| פין T1 | AN10/RB10 — Analog input / GPIO port B |
| פין T12 | AN11/RB11 — Analog input / GPIO port B |
| פין U1 | AN12/RB12 — Analog input / GPIO port B |
| פין U12 | AN13/RB13 — Analog input / GPIO port B |
| פין V1 | AN14/RB14 — Analog input / GPIO port B |
| פין V12 | AN15/RB15 — Analog input / GPIO port B |
| פין W1 | VSS — Ground |
| פין W12 | VDD — Core digital supply |
| פין H3 | OSC1/RC12 — Crystal oscillator input |
| פין H4 | OSC2/RC13 — Crystal oscillator output |
| פין J3 | SOSCI/RC14 — Secondary oscillator input |
| פין J4 | SOSCO/RC1 — Secondary oscillator output |
| פין F4 | TCK/RPA0 — JTAG test clock |
| פין G4 | TDI/RPA1 — JTAG test data in |
| פין E4 | TDO/RPA2 — JTAG test data out |
| פין D4 | TMS/RPA3 — JTAG test mode select |
| פין F3 | TRST/RPA8 — JTAG test reset |
| פין D3 | MCLR — Master clear reset |
| פין K3 | VBAT — RTCC battery supply 2.0-3.6V |
| פין L3 | RTCC/RE0 — RTCC output / GPIO |
| פין M3 | SDA1/RA4 — I2C1 data / GPIO |
| פין N3 | SCL1/RA5 — I2C1 clock / GPIO |
| פין P3 | SDA2/RA2 — I2C2 data / GPIO |
| פין R3 | SCL2/RA3 — I2C2 clock / GPIO |
| פין T3 | U1RX/RF4 — UART1 receive / GPIO |
| פין U3 | U1TX/RF5 — UART1 transmit / GPIO |
| פין V3 | U2RX/RG7 — UART2 receive / GPIO |
| פין W3 | U2TX/RG8 — UART2 transmit / GPIO |
| פין K4 | SDO1/RA1 — SPI1 data out / GPIO |
| פין L4 | SDI1/RA0 — SPI1 data in / GPIO |
| פין M4 | SCK1/RA6 — SPI1 clock / GPIO |
| פין N4 | SS1/RA7 — SPI1 slave select / GPIO |
| פין P4 | SDO2/RG0 — SPI2 data out / GPIO |
| פין R4 | SDI2/RG1 — SPI2 data in / GPIO |
| פין T4 | SCK2/RG2 — SPI2 clock / GPIO |
| פין U4 | SS2/RG3 — SPI2 slave select / GPIO |
| פין V4 | C1TX/RF1 — CAN1 transmit / GPIO |
| פין W4 | C1RX/RF0 — CAN1 receive / GPIO |
| פין K5 | C2TX/RG5 — CAN2 transmit / GPIO |
| פין L5 | C2RX/RG4 — CAN2 receive / GPIO |
| פין M5 | D+/RG2 — USB D+ data line (note pin shared) |
| פין N5 | D-/RG3 — USB D- data line (note pin shared) |
| פין P5 | VUSB — USB transceiver supply 3.3V |
| פין R5 | VSS — Ground |
| פין T5 | ETXD0/RF3 — Ethernet MAC TX data 0 |
| פין U5 | ETXD1/RF2 — Ethernet MAC TX data 1 |
| פין V5 | ETXD2/RH8 — Ethernet MAC TX data 2 (MII) |
| פין W5 | ETXD3/RH9 — Ethernet MAC TX data 3 (MII) |
| פין K6 | ERXD0/RH10 — Ethernet MAC RX data 0 |
| פין L6 | ERXD1/RH11 — Ethernet MAC RX data 1 |
| פין M6 | ERXD2/RH12 — Ethernet MAC RX data 2 (MII) |
| פין N6 | ERXD3/RH13 — Ethernet MAC RX data 3 (MII) |
| פין P6 | ERXDV/RG9 — Ethernet RX data valid |
| פין R6 | ERXCLK/RG15 — Ethernet RX clock |
| פין T6 | ERXERR/RH14 — Ethernet RX error |
| פין U6 | ETXEN/RG6 — Ethernet TX enable |
| פין V6 | ETXERR/RH15 — Ethernet TX error |
| פין W6 | ECRS/RH4 — Ethernet carrier sense |
| פין K7 | ECOL/RH5 — Ethernet collision detected |
| פין L7 | EMDC/RH0 — Ethernet management data clock |
| פין M7 | EMDIO/RH1 — Ethernet management data I/O |
| פין N7 | OC1/RD0 — Output compare 1 / GPIO |
| פין P7 | OC2/RD1 — Output compare 2 / GPIO |
| פין R7 | OC3/RD2 — Output compare 3 / GPIO |
| פין T7 | OC4/RD3 — Output compare 4 / GPIO |
| פין U7 | OC5/RD4 — Output compare 5 / GPIO |
| פין V7 | IC1/RD5 — Input capture 1 / GPIO |
| פין W7 | IC2/RD6 — Input capture 2 / GPIO |
| פין K8 | IC3/RD7 — Input capture 3 / GPIO |
| פין L8 | IC4/RD8 — Input capture 4 / GPIO |
| פין M8 | IC5/RD9 — Input capture 5 / GPIO |
| פין N8 | INT0/RE8 — External interrupt 0 / GPIO |
| פין P8 | INT1/RE9 — External interrupt 1 / GPIO |
| פין R8 | INT2/RA14 — External interrupt 2 / GPIO |
| פין T8 | INT3/RA15 — External interrupt 3 / GPIO |
| פין U8 | INT4/RG14 — External interrupt 4 / GPIO |
| פין V8 | T1CK/RG6 — Timer1 clock input / GPIO |
| פין W8 | T2CK/RG7 — Timer2 clock input / GPIO |
| פין K9 | T3CK/RG8 — Timer3 clock input / GPIO |
| פין L9 | T4CK/RG9 — Timer4 clock input / GPIO |
| פין M9 | T5CK/RA10 — Timer5 clock input / GPIO |
| פין N9 | VSS — Ground |
| פין P9 | VDD — Core digital supply |
| פין R9 | RGMCS1/RF12 — PMP chip select 1 / GPIO |
| פין T9 | RGMCS2/RF13 — PMP chip select 2 / GPIO |
| פין U9 | RGMRD/RD5 — PMP read strobe / GPIO |
| פין V9 | RGMWR/RD4 — PMP write strobe / GPIO |
| פין W9 | RGMA0/RF0 — PMP address 0 / GPIO |
| פין K10 | RGMA1/RF1 — PMP address 1 / GPIO |
| פין L10 | RGMA2/RG0 — PMP address 2 / GPIO |
| פין M10 | RGMA3/RG1 — PMP address 3 / GPIO |
| פין N10 | RGMA4/RG2 — PMP address 4 / GPIO |
| פין P10 | RGMA5/RG3 — PMP address 5 / GPIO |
| פין R10 | RGMA6/RH0 — PMP address 6 / GPIO |
| פין T10 | RGMA7/RH1 — PMP address 7 / GPIO |
| פין U10 | RGMA8/RH2 — PMP address 8 / GPIO |
| פין V10 | RGMA9/RH3 — PMP address 9 / GPIO |
| פין W10 | RGMA10/RH4 — PMP address 10 / GPIO |
| פין K11 | RGMA11/RH5 — PMP address 11 / GPIO |
| פין L11 | RGMA12/RH6 — PMP address 12 / GPIO |
| פין M11 | RGMA13/RH7 — PMP address 13 / GPIO |
| פין N11 | RGMA14/RH8 — PMP address 14 / GPIO |
| פין P11 | RGMA15/RH9 — PMP address 15 / GPIO |
| פין R11 | RGMWRH/RH10 — PMP write upper byte / GPIO |
| פין T11 | RGMRDH/RH11 — PMP read upper byte / GPIO |
| פין U11 | RGMENB/RH12 — PMP enable upper byte / GPIO |
| פין V11 | RGMCS0/RH13 — PMP chip select 0 / GPIO |
| פין W11 | RGMALH/RH14 — PMP address latch / GPIO |
יישומים טיפוסיים
PIC32MX775F256LT-80I/BG מתאים עבור 7 יישוםs: Industrial Ethernet Node / Modbus TCP Gateway, Automotive CAN Body/Powertrain Network Node, USB Device / Embedded Host Industrial Controller, Building Automation Controller (BACnet / Modbus), Graphical HMI with TFT Display, Networked Medical Instrumentation, Data Acquisition and Control System.
Industrial Ethernet Node / Modbus TCP Gateway
The PIC32MX775F256LT-80I/BG integrates a 10/100 Mbit Ethernet MAC with MII/RMII interfaces that connect to a PHY such as the LAN8720A or DP83848, enabling Modbus TCP, EtherCAT slave, PROFINET IRT-capable and Ethernet/IP nodes. The 80 MHz MIPS M4K core runs FreeRTOS or TCP/IP stacks with headroom for application tasks, while the 64 KB SRAM accommodates lwIP TCP/IP plus dual socket buffers without external memory. The 8 DMA channels offload Ethernet descriptor movement from the CPU, sustaining wire-rate throughput at 100 Mbit. Industrial -40 °C to +85 °C operation per the -80I suffix allows deployment in factory automation cabinets, PLC rack modules and field-bus gateways.
מומלץ
Automotive CAN Body/Powertrain Network Node
The dual CAN 2.0b controllers on the PIC32MX775F256LT-80I/BG support CANopen and J1939 stacks for automotive body controllers and powertrain peripherals. Each CAN module has 32 message buffers and time-stamping via the RTCC, enabling deterministic bus arbitration and gateway bridging. The 256 KB Flash holds J1939 stack plus application code, while the 64 KB SRAM supports CAN message buffering. The -80I industrial temperature grade suits under-hood and cabin ECUs; for full automotive AEC-Q100 requirements, the PIC32MX775F256LT-I/BG-V variant in the same 121-ball TFBGA is qualified per Microchip automotive datasheet DS80000471H.
מומלץ
USB Device / Embedded Host Industrial Controller
The PIC32MX775F256LT-80I/BG's USB 2.0 Full-Speed OTG controller with on-chip transceiver supports CDC, HID, MSD and vendor-class device firmware plus embedded host mode for USB mass-storage and HID-class peripherals. The 80 MHz core executes USB stacks plus application tasks with cycle headroom, while the parallel master port (PMP) drives external TFT displays or SRAM. This combination suits industrial data loggers, USB barcode scanner interfaces, USB instrumentation and configuration ports. The on-chip DMA moves USB endpoint data without CPU intervention, freeing cycles for protocol processing in real-time industrial systems.
מומלץ
Building Automation Controller (BACnet / Modbus)
The PIC32MX775F256LT-80I/BG's combined Ethernet MAC and dual CAN peripherals support BACnet/IP over Ethernet plus CAN-based HVAC and lighting subsystems in commercial building automation. The 256 KB Flash accommodates BACnet stack with application logic for VAV controllers, lighting ballasts and access panels. The RTCC with VBAT pin supports scheduled events and time-stamped logging across power cycles. Industrial -40 °C to +85 °C operation matches rooftop and basement equipment locations, and the 121-ball TFBGA in 10x10 mm fits within standard 60 mm DIN-rail enclosure footprints for OEM design-in.
מומלץ
Graphical HMI with TFT Display
The parallel master port (PMP) on the PIC32MX775F256LT-80I/BG drives 8-bit or 16-bit TFT displays up to QVGA resolution, enabling graphical HMI panels for industrial equipment, medical instruments and appliance front panels. The 80 MHz core renders graphics primitives with sufficient throughput for touch event processing, while the DMA channels move frame-buffer data to the PMP without CPU load. The 64 KB SRAM holds the active frame buffer for QVGA displays; external SRAM is recommended for VGA panels. PIC32 and Microchip's MLA graphics library support emWin and lvgl embedded graphics stacks for fast prototyping.
מומלץ
Networked Medical Instrumentation
The PIC32MX775F256LT-80I/BG supports networked medical devices such as patient monitors, infusion pumps and diagnostic instruments requiring Ethernet connectivity and deterministic real-time response. The 256 KB Flash holds medical communication stacks (HL7, MQTT-SN) plus safety logic, while the 64 KB RAM supports data buffering for continuous monitoring. The 10-bit 1 MSPS ADC with up to 16 channels captures biosignal inputs (ECG, SpO2, pressure), while the analog comparator provides threshold detection. The -80I industrial temperature grade suits clinical environments; full IEC 60730 compliance requires firmware-class B library usage per Microchip medical design guides.
מומלץ
Data Acquisition and Control System
The PIC32MX775F256LT-80I/BG's combination of 10-bit 1 MSPS ADC with up to 16 channels, multiple UART/SPI/I2C interfaces, and dual CAN modules suits multi-channel industrial data acquisition systems. Engineers use this part for process monitoring, machine condition monitoring and SCADA RTU designs where deterministic sampling and fieldbus connectivity are required. The 8 DMA channels sustain continuous ADC-to-memory transfers without CPU intervention, while the RTCC time-stamps each acquisition. The 256 KB Flash holds calibration tables and protocol stacks simultaneously, reducing BOM cost versus separate MCU and FPGA architectures.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור PIC32MX775F256LT-80I/BG — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | PIC32MX775F256L-80I/BG | PIC32MX675F256LT-80I/BG | PIC32MX575F256LT-80I/BG | PIC32MX764F128LT-I/BG | PIC32MX695F512L-80I/BG | PIC32MX360F256LT-80I/BG |
|---|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 121-TFBGA (10x10) | 121-TFBGA (10x10) - same | 121-TFBGA (10x10) - same | 121-TFBGA (10x10) - same | 121-TFBGA (10x10) - same | 121-TFBGA (10x10) - same | 121-TFBGA (10x10) - same |
| Flash Size | 256 KB | 256 KB | 256 KB | 256 KB | 128 KB (-50%) | 512 KB (+100%) | 256 KB |
| RAM Size | 64 KB | 64 KB | 64 KB | 64 KB | 32 KB (-50%) | 128 KB (+100%) | 64 KB |
| Core Speed | 80 MHz | 80 MHz | 80 MHz | 80 MHz | 80 MHz | 80 MHz | 80 MHz |
| Ethernet MAC | Yes (10/100 MII/RMII) | Yes (10/100 MII/RMII) | Yes (10/100 MII/RMII) | No | Yes (10/100 MII/RMII) | Yes (10/100 MII/RMII) | No |
| CAN 2.0b Controllers | 2 | 2 | 0 | 0 | 2 | 2 | 0 |
| USB 2.0 OTG | Yes (Full-Speed) | Yes (Full-Speed) | Yes (Full-Speed) | Yes (Full-Speed) | Yes (Full-Speed) | Yes (Full-Speed) | Yes (Full-Speed) |
| Operating Temperature | -40 °C to +85 °C (-80I) | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C |
מבדילים עיקריים
- Dual CAN 2.0b controllers + 10/100 Ethernet MAC integrated (לעומתPIC32MX575F256LT-80I/BG)
- Larger 64 KB SRAM versus 32 KB on PIC32MX664 family (לעומתPIC32MX664F128LT-I/BG)
- Free MPLAB Harmony and XC32 compiler support (לעומתPIC32MX360F256LT-80I/BG)
הערות תכנון
The 121-ball TFBGA package uses 0.8 mm ball pitch which requires 4-layer PCB routing with microvia-in-pad or dogbone fanout. Use Microchip's recommended 0.4 mm escape traces, 0.2 mm via drill and 0.4 mm via pad. Place 0.1 µF X7R 0402 decoupling capacitors adjacent to each VDD/VSS ball pair, plus 4.7 µF bulk capacitors near each corner. Maintain a continuous ground reference under the BGA for SI and EMI performance per Microchip AN1255 PCB layout guidelines.
Do not omit the ICSP programming footprint on production PCBs - the PIC32MX775F256LT-80I/BG requires ICSP for firmware loading even if JTAG is present. Reserve at minimum PGECx/PGEDx test points plus MCLR pull-up to VDD via 10 kΩ. The 80 MHz prefetch cache must be enabled in the system configuration register before Flash execution at zero wait states; otherwise code runs at half speed per the PIC32MX5/6/7 family errata DS80000471H.
Estimated: at maximum core activity (80 MHz, all peripherals active, 3.6 V VDD) the PIC32MX775F256LT-80I/BG draws approximately 70-110 mA total. Power dissipation is approximately 250-400 mW; the 121-ball TFBGA package has thermal resistance θJA of approximately 30 C/W on 4-layer JEDEC EIA/JESD51 test board, yielding a self-heating rise of 8-12 C above ambient. For industrial -40 °C to +85 °C operation, ensure ambient + self-heating stays below the maximum 85 °C rating. Operational decoupling to minimum 2.3 V VDD and Sleep mode reduces idle power to approximately 50 µA per the family reference manual.
Route Ethernet MII/RMII signals with controlled impedance (50 Ω single-ended to ground reference) and length-matching per the MII/RMII specification. Use a series 33 Ω damping resistor on each MII output if signal integrity issues arise. Place the Ethernet PHY within 100 mm of the MCU with the clock trace length matched within 25 mm. For USB Full-Speed signals, maintain 90 Ω differential impedance on D+/D- per the USB 2.0 specification and place the USBLC6 ESD protection within 5 mm of the connector.
מידע על תאימות
RoHS compliant per Microchip product page (BG suffix indicates lead-free TFBGA). Industrial -80I temperature grade meets -40 °C to +85 °C; for AEC-Q100 automotive qualification, choose the PIC32MX775F256LT-I/BG-V automotive variant (refer to Microchip automotive datasheet DS80000471H). REACH compliance per Microchip product declaration.
