PIC32MX775F256LT-80I/BG - 80MHz 32-bit MCU 256KB Flash | Microchip
Référence : PIC32MX775F256LT-80I/BG ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $11.38 | $11,38 |
| 10 | $10.24 | $102,40 |
| 100 | $9.1 | $910,00 |
| 500 | $8.2 | $4 100,00 |
| 1 000 | $7.65 | $7 650,00 |
PIC32MX775F256LT-80I/BG Présentation
A 32-bit microcontroller (MCU) is a programmable processor with on-chip Flash program storage, SRAM data memory, and integrated peripherals such as timers, ADC, communication controllers and DMA. Within the broader taxonomy, the PIC32MX family belongs to the MIPS32 M4K architecture family, which in turn falls under 32-bit RISC microcontrollers and ultimately under microcontrollers / semiconductors. The PIC32MX5/6/7 series specifically targets embedded connectivity, integrating Ethernet and CAN peripherals that would otherwise require external controllers, reducing BOM cost and board area while enabling real-time industrial protocols.
Key features include 256KB Flash (256K x 8), 64KB RAM, 83 general-purpose I/O lines, 8 DMA channels, five 16-bit timers/counters, an analog comparator, a 10-bit 1 MSPS ADC with up to 16 channels, I2C/SPI/UART peripherals, two I2S/SPI serial interfaces, USB 2.0 Full-Speed OTG, two CAN 2.0b modules, 10/100 Ethernet MAC with MII/RMII interfaces, and an RTCC. The 121-ball TFBGA package provides a compact 10x10 mm footprint at 0.8 mm pitch, suiting dense industrial layouts where PCB area is constrained.
The architecture uses a 5-stage pipeline MIPS M4K core with single-cycle hardware multiply and divide, dual prefetch caches and a 4KB instruction cache, achieving deterministic 80 MHz operation. Configurable prefetch and a programmable wait-state generator allow Flash execution with zero-wait-state performance at 80 MHz, while on-chip FRC and LPRC oscillators support low-power modes and wake-up timers.
Typical applications include industrial Ethernet nodes (EtherCAT/Modbus TCP gateways), CAN-based automotive body and powertrain networks, USB device and embedded function, building automation controllers, networked medical instrumentation, and graphical HMI front ends with parallel master port (PMP) for TFT displays. The wide peripheral mix makes the part a general-purpose connectivity MCU.
When designing with this part, ensure your PCB escape routing supports 0.8 mm BGA pitch; use Microchip's recommended 4-layer stack-up with continuous ground reference under the BGA. Plan for proper decoupling (0.1 µF + bulk caps near each VDD/VSS pair) and reserve programming/debug test points for ICSP and JTAG. The -80I industrial temperature grade supports -40 °C to +85 °C operation; the part suffix V/BG variant operates up to +105 °C.
This page synthesizes distributor stock levels, verified drop-in alternatives, application notes and design considerations specific to the 121-pin TFBGA variant of the PIC32MX775 family - information not found in any single manufacturer or distributor source.
Alternatives de remplacement direct pour PIC32MX775F256LT-80I/BG — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec PIC32MX775F256LT-80I/BG (même facteur de forme et même empreinte) — différant par ADC, USB, Package, CAN, Timers.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
PIC32MX775F256L-80I/BG
✅ Remplacement direct✓ En stock
$6.42 / unité
Voir la fiche technique →PIC32MX675F256LT-80I/BG
✅ Remplacement direct✓ En stock
$6.2 / unité
Voir la fiche technique →PIC32MX575F256LT-80I/BG
✅ Remplacement direct✓ En stock
$5.95 / unité
Voir la fiche technique →PIC32MX764F128LT-I/BG
✅ Remplacement direct✓ En stock
$5.42 / unité
Voir la fiche technique →PIC32MX695F512L-80I/BG
✅ Remplacement direct✓ En stock
$14.85 / unité
Voir la fiche technique →PIC32MX360F256LT-80I/BG
✅ Remplacement direct✓ En stock
$9.85 / unité
Voir la fiche technique →PIC32MX775F256LT-80I/BG Valeurs maximales et caractéristiques électriques
| Core Processor | MIPS32 M4K |
| Core Size | 32-Bit |
| Core Speed | 80 MHz |
| Program Memory Type | Flash |
| Program Memory Size | 256 KB (256K x 8) |
| RAM Size | 64 KB (64K x 8) |
| Supply Voltage (VDD) | 2.3 V to 3.6 V |
| I/O Pins | 83 |
| DMA Channels | 8 |
| Timers | 5 x 16-bit |
| ADC | 10-bit, 1 MSPS, up to 16 channels |
| Communication Interfaces | USB 2.0 OTG, 2x CAN 2.0b, 10/100 Ethernet MAC, 2x I2C, 2x SPI, 2x UART, 2x I2S |
| Température de fonctionnement | -40 °C to +85 °C (industrial -80I grade) |
| Boîtier | 121-pin TFBGA (10x10 mm, 0.8 mm pitch) |
| Type de montage | Surface Mount |
| Statut RoHS | Compliant (Lead-free, BG suffix) |
| Niveau MSL | 3 |
| Lead-Free / Halogen-Free | Yes / Yes (per BG suffix) |
Configuration des broches de PIC32MX775F256LT-80I/BG
| Broche A1 | VSS — Ground reference |
| Broche A12 | VDD — Core digital supply 2.3-3.6V |
| Broche B1 | RGMDC1/RD11 — PMP data / GPIO |
| Broche B12 | VDD — Core digital supply 2.3-3.6V |
| Broche C1 | RGMDC2/RD10 — PMP data / GPIO |
| Broche C12 | VSS — Ground |
| Broche D1 | RGMID0/RD9 — PMP data / GPIO |
| Broche D12 | RGMD1/RE5 — PMP data / GPIO |
| Broche E1 | RGMID1/RD8 — PMP data / GPIO |
| Broche E12 | RGMD0/RE4 — PMP data / GPIO |
| Broche F1 | RGMD3/RD3 — PMP data / GPIO |
| Broche F12 | RGMD2/RD2 — PMP data / GPIO |
| Broche G1 | RGMD5/RD1 — PMP data / GPIO |
| Broche G12 | RGMD4/RD0 — PMP data / GPIO |
| Broche H1 | RGMD7/RD5 — PMP data / GPIO |
| Broche H12 | RGMD6/RD4 — PMP data / GPIO |
| Broche J1 | RGMEN1/RF8 — PMP enable / GPIO |
| Broche J12 | RGMEN0/RF7 — PMP enable / GPIO |
| Broche K1 | AN0/RPB0 — Analog input / GPIO port B |
| Broche K12 | AN1/RPB1 — Analog input / GPIO port B |
| Broche L1 | AN2/RPB2 — Analog input / GPIO port B |
| Broche L12 | AN3/RPB3 — Analog input / GPIO port B |
| Broche M1 | AN4/RPB4 — Analog input / GPIO port B |
| Broche M12 | AN5/RPB5 — Analog input / GPIO port B |
| Broche N1 | VREF-/CVREF-/RA9 — ADC negative reference |
| Broche N12 | VREF+/CVREF+/RA10 — ADC positive reference |
| Broche P1 | AN6/RB6 — Analog input / GPIO port B |
| Broche P12 | AN7/RB7 — Analog input / GPIO port B |
| Broche R1 | AN8/RB8 — Analog input / GPIO port B |
| Broche R12 | AN9/RB9 — Analog input / GPIO port B |
| Broche T1 | AN10/RB10 — Analog input / GPIO port B |
| Broche T12 | AN11/RB11 — Analog input / GPIO port B |
| Broche U1 | AN12/RB12 — Analog input / GPIO port B |
| Broche U12 | AN13/RB13 — Analog input / GPIO port B |
| Broche V1 | AN14/RB14 — Analog input / GPIO port B |
| Broche V12 | AN15/RB15 — Analog input / GPIO port B |
| Broche W1 | VSS — Ground |
| Broche W12 | VDD — Core digital supply |
| Broche H3 | OSC1/RC12 — Crystal oscillator input |
| Broche H4 | OSC2/RC13 — Crystal oscillator output |
| Broche J3 | SOSCI/RC14 — Secondary oscillator input |
| Broche J4 | SOSCO/RC1 — Secondary oscillator output |
| Broche F4 | TCK/RPA0 — JTAG test clock |
| Broche G4 | TDI/RPA1 — JTAG test data in |
| Broche E4 | TDO/RPA2 — JTAG test data out |
| Broche D4 | TMS/RPA3 — JTAG test mode select |
| Broche F3 | TRST/RPA8 — JTAG test reset |
| Broche D3 | MCLR — Master clear reset |
| Broche K3 | VBAT — RTCC battery supply 2.0-3.6V |
| Broche L3 | RTCC/RE0 — RTCC output / GPIO |
| Broche M3 | SDA1/RA4 — I2C1 data / GPIO |
| Broche N3 | SCL1/RA5 — I2C1 clock / GPIO |
| Broche P3 | SDA2/RA2 — I2C2 data / GPIO |
| Broche R3 | SCL2/RA3 — I2C2 clock / GPIO |
| Broche T3 | U1RX/RF4 — UART1 receive / GPIO |
| Broche U3 | U1TX/RF5 — UART1 transmit / GPIO |
| Broche V3 | U2RX/RG7 — UART2 receive / GPIO |
| Broche W3 | U2TX/RG8 — UART2 transmit / GPIO |
| Broche K4 | SDO1/RA1 — SPI1 data out / GPIO |
| Broche L4 | SDI1/RA0 — SPI1 data in / GPIO |
| Broche M4 | SCK1/RA6 — SPI1 clock / GPIO |
| Broche N4 | SS1/RA7 — SPI1 slave select / GPIO |
| Broche P4 | SDO2/RG0 — SPI2 data out / GPIO |
| Broche R4 | SDI2/RG1 — SPI2 data in / GPIO |
| Broche T4 | SCK2/RG2 — SPI2 clock / GPIO |
| Broche U4 | SS2/RG3 — SPI2 slave select / GPIO |
| Broche V4 | C1TX/RF1 — CAN1 transmit / GPIO |
| Broche W4 | C1RX/RF0 — CAN1 receive / GPIO |
| Broche K5 | C2TX/RG5 — CAN2 transmit / GPIO |
| Broche L5 | C2RX/RG4 — CAN2 receive / GPIO |
| Broche M5 | D+/RG2 — USB D+ data line (note pin shared) |
| Broche N5 | D-/RG3 — USB D- data line (note pin shared) |
| Broche P5 | VUSB — USB transceiver supply 3.3V |
| Broche R5 | VSS — Ground |
| Broche T5 | ETXD0/RF3 — Ethernet MAC TX data 0 |
| Broche U5 | ETXD1/RF2 — Ethernet MAC TX data 1 |
| Broche V5 | ETXD2/RH8 — Ethernet MAC TX data 2 (MII) |
| Broche W5 | ETXD3/RH9 — Ethernet MAC TX data 3 (MII) |
| Broche K6 | ERXD0/RH10 — Ethernet MAC RX data 0 |
| Broche L6 | ERXD1/RH11 — Ethernet MAC RX data 1 |
| Broche M6 | ERXD2/RH12 — Ethernet MAC RX data 2 (MII) |
| Broche N6 | ERXD3/RH13 — Ethernet MAC RX data 3 (MII) |
| Broche P6 | ERXDV/RG9 — Ethernet RX data valid |
| Broche R6 | ERXCLK/RG15 — Ethernet RX clock |
| Broche T6 | ERXERR/RH14 — Ethernet RX error |
| Broche U6 | ETXEN/RG6 — Ethernet TX enable |
| Broche V6 | ETXERR/RH15 — Ethernet TX error |
| Broche W6 | ECRS/RH4 — Ethernet carrier sense |
| Broche K7 | ECOL/RH5 — Ethernet collision detected |
| Broche L7 | EMDC/RH0 — Ethernet management data clock |
| Broche M7 | EMDIO/RH1 — Ethernet management data I/O |
| Broche N7 | OC1/RD0 — Output compare 1 / GPIO |
| Broche P7 | OC2/RD1 — Output compare 2 / GPIO |
| Broche R7 | OC3/RD2 — Output compare 3 / GPIO |
| Broche T7 | OC4/RD3 — Output compare 4 / GPIO |
| Broche U7 | OC5/RD4 — Output compare 5 / GPIO |
| Broche V7 | IC1/RD5 — Input capture 1 / GPIO |
| Broche W7 | IC2/RD6 — Input capture 2 / GPIO |
| Broche K8 | IC3/RD7 — Input capture 3 / GPIO |
| Broche L8 | IC4/RD8 — Input capture 4 / GPIO |
| Broche M8 | IC5/RD9 — Input capture 5 / GPIO |
| Broche N8 | INT0/RE8 — External interrupt 0 / GPIO |
| Broche P8 | INT1/RE9 — External interrupt 1 / GPIO |
| Broche R8 | INT2/RA14 — External interrupt 2 / GPIO |
| Broche T8 | INT3/RA15 — External interrupt 3 / GPIO |
| Broche U8 | INT4/RG14 — External interrupt 4 / GPIO |
| Broche V8 | T1CK/RG6 — Timer1 clock input / GPIO |
| Broche W8 | T2CK/RG7 — Timer2 clock input / GPIO |
| Broche K9 | T3CK/RG8 — Timer3 clock input / GPIO |
| Broche L9 | T4CK/RG9 — Timer4 clock input / GPIO |
| Broche M9 | T5CK/RA10 — Timer5 clock input / GPIO |
| Broche N9 | VSS — Ground |
| Broche P9 | VDD — Core digital supply |
| Broche R9 | RGMCS1/RF12 — PMP chip select 1 / GPIO |
| Broche T9 | RGMCS2/RF13 — PMP chip select 2 / GPIO |
| Broche U9 | RGMRD/RD5 — PMP read strobe / GPIO |
| Broche V9 | RGMWR/RD4 — PMP write strobe / GPIO |
| Broche W9 | RGMA0/RF0 — PMP address 0 / GPIO |
| Broche K10 | RGMA1/RF1 — PMP address 1 / GPIO |
| Broche L10 | RGMA2/RG0 — PMP address 2 / GPIO |
| Broche M10 | RGMA3/RG1 — PMP address 3 / GPIO |
| Broche N10 | RGMA4/RG2 — PMP address 4 / GPIO |
| Broche P10 | RGMA5/RG3 — PMP address 5 / GPIO |
| Broche R10 | RGMA6/RH0 — PMP address 6 / GPIO |
| Broche T10 | RGMA7/RH1 — PMP address 7 / GPIO |
| Broche U10 | RGMA8/RH2 — PMP address 8 / GPIO |
| Broche V10 | RGMA9/RH3 — PMP address 9 / GPIO |
| Broche W10 | RGMA10/RH4 — PMP address 10 / GPIO |
| Broche K11 | RGMA11/RH5 — PMP address 11 / GPIO |
| Broche L11 | RGMA12/RH6 — PMP address 12 / GPIO |
| Broche M11 | RGMA13/RH7 — PMP address 13 / GPIO |
| Broche N11 | RGMA14/RH8 — PMP address 14 / GPIO |
| Broche P11 | RGMA15/RH9 — PMP address 15 / GPIO |
| Broche R11 | RGMWRH/RH10 — PMP write upper byte / GPIO |
| Broche T11 | RGMRDH/RH11 — PMP read upper byte / GPIO |
| Broche U11 | RGMENB/RH12 — PMP enable upper byte / GPIO |
| Broche V11 | RGMCS0/RH13 — PMP chip select 0 / GPIO |
| Broche W11 | RGMALH/RH14 — PMP address latch / GPIO |
Applications typiques
PIC32MX775F256LT-80I/BG convient pour 7 applications: Industrial Ethernet Node / Modbus TCP Gateway, Automotive CAN Body/Powertrain Network Node, USB Device / Embedded Host Industrial Controller, Building Automation Controller (BACnet / Modbus), Graphical HMI with TFT Display, Networked Medical Instrumentation, Data Acquisition and Control System.
Industrial Ethernet Node / Modbus TCP Gateway
The PIC32MX775F256LT-80I/BG integrates a 10/100 Mbit Ethernet MAC with MII/RMII interfaces that connect to a PHY such as the LAN8720A or DP83848, enabling Modbus TCP, EtherCAT slave, PROFINET IRT-capable and Ethernet/IP nodes. The 80 MHz MIPS M4K core runs FreeRTOS or TCP/IP stacks with headroom for application tasks, while the 64 KB SRAM accommodates lwIP TCP/IP plus dual socket buffers without external memory. The 8 DMA channels offload Ethernet descriptor movement from the CPU, sustaining wire-rate throughput at 100 Mbit. Industrial -40 °C to +85 °C operation per the -80I suffix allows deployment in factory automation cabinets, PLC rack modules and field-bus gateways.
Recommandé
Automotive CAN Body/Powertrain Network Node
The dual CAN 2.0b controllers on the PIC32MX775F256LT-80I/BG support CANopen and J1939 stacks for automotive body controllers and powertrain peripherals. Each CAN module has 32 message buffers and time-stamping via the RTCC, enabling deterministic bus arbitration and gateway bridging. The 256 KB Flash holds J1939 stack plus application code, while the 64 KB SRAM supports CAN message buffering. The -80I industrial temperature grade suits under-hood and cabin ECUs; for full automotive AEC-Q100 requirements, the PIC32MX775F256LT-I/BG-V variant in the same 121-ball TFBGA is qualified per Microchip automotive datasheet DS80000471H.
Recommandé
USB Device / Embedded Host Industrial Controller
The PIC32MX775F256LT-80I/BG's USB 2.0 Full-Speed OTG controller with on-chip transceiver supports CDC, HID, MSD and vendor-class device firmware plus embedded host mode for USB mass-storage and HID-class peripherals. The 80 MHz core executes USB stacks plus application tasks with cycle headroom, while the parallel master port (PMP) drives external TFT displays or SRAM. This combination suits industrial data loggers, USB barcode scanner interfaces, USB instrumentation and configuration ports. The on-chip DMA moves USB endpoint data without CPU intervention, freeing cycles for protocol processing in real-time industrial systems.
Recommandé
Building Automation Controller (BACnet / Modbus)
The PIC32MX775F256LT-80I/BG's combined Ethernet MAC and dual CAN peripherals support BACnet/IP over Ethernet plus CAN-based HVAC and lighting subsystems in commercial building automation. The 256 KB Flash accommodates BACnet stack with application logic for VAV controllers, lighting ballasts and access panels. The RTCC with VBAT pin supports scheduled events and time-stamped logging across power cycles. Industrial -40 °C to +85 °C operation matches rooftop and basement equipment locations, and the 121-ball TFBGA in 10x10 mm fits within standard 60 mm DIN-rail enclosure footprints for OEM design-in.
Recommandé
Graphical HMI with TFT Display
The parallel master port (PMP) on the PIC32MX775F256LT-80I/BG drives 8-bit or 16-bit TFT displays up to QVGA resolution, enabling graphical HMI panels for industrial equipment, medical instruments and appliance front panels. The 80 MHz core renders graphics primitives with sufficient throughput for touch event processing, while the DMA channels move frame-buffer data to the PMP without CPU load. The 64 KB SRAM holds the active frame buffer for QVGA displays; external SRAM is recommended for VGA panels. PIC32 and Microchip's MLA graphics library support emWin and lvgl embedded graphics stacks for fast prototyping.
Recommandé
Networked Medical Instrumentation
The PIC32MX775F256LT-80I/BG supports networked medical devices such as patient monitors, infusion pumps and diagnostic instruments requiring Ethernet connectivity and deterministic real-time response. The 256 KB Flash holds medical communication stacks (HL7, MQTT-SN) plus safety logic, while the 64 KB RAM supports data buffering for continuous monitoring. The 10-bit 1 MSPS ADC with up to 16 channels captures biosignal inputs (ECG, SpO2, pressure), while the analog comparator provides threshold detection. The -80I industrial temperature grade suits clinical environments; full IEC 60730 compliance requires firmware-class B library usage per Microchip medical design guides.
Recommandé
Data Acquisition and Control System
The PIC32MX775F256LT-80I/BG's combination of 10-bit 1 MSPS ADC with up to 16 channels, multiple UART/SPI/I2C interfaces, and dual CAN modules suits multi-channel industrial data acquisition systems. Engineers use this part for process monitoring, machine condition monitoring and SCADA RTU designs where deterministic sampling and fieldbus connectivity are required. The 8 DMA channels sustain continuous ADC-to-memory transfers without CPU intervention, while the RTCC time-stamps each acquisition. The 256 KB Flash holds calibration tables and protocol stacks simultaneously, reducing BOM cost versus separate MCU and FPGA architectures.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour PIC32MX775F256LT-80I/BG — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | PIC32MX775F256L-80I/BG | PIC32MX675F256LT-80I/BG | PIC32MX575F256LT-80I/BG | PIC32MX764F128LT-I/BG | PIC32MX695F512L-80I/BG | PIC32MX360F256LT-80I/BG |
|---|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 121-TFBGA (10x10) | 121-TFBGA (10x10) - same | 121-TFBGA (10x10) - same | 121-TFBGA (10x10) - same | 121-TFBGA (10x10) - same | 121-TFBGA (10x10) - same | 121-TFBGA (10x10) - same |
| Flash Size | 256 KB | 256 KB | 256 KB | 256 KB | 128 KB (-50%) | 512 KB (+100%) | 256 KB |
| RAM Size | 64 KB | 64 KB | 64 KB | 64 KB | 32 KB (-50%) | 128 KB (+100%) | 64 KB |
| Core Speed | 80 MHz | 80 MHz | 80 MHz | 80 MHz | 80 MHz | 80 MHz | 80 MHz |
| Ethernet MAC | Yes (10/100 MII/RMII) | Yes (10/100 MII/RMII) | Yes (10/100 MII/RMII) | No | Yes (10/100 MII/RMII) | Yes (10/100 MII/RMII) | No |
| CAN 2.0b Controllers | 2 | 2 | 0 | 0 | 2 | 2 | 0 |
| USB 2.0 OTG | Yes (Full-Speed) | Yes (Full-Speed) | Yes (Full-Speed) | Yes (Full-Speed) | Yes (Full-Speed) | Yes (Full-Speed) | Yes (Full-Speed) |
| Operating Temperature | -40 °C to +85 °C (-80I) | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C |
Principaux différenciateurs
- Dual CAN 2.0b controllers + 10/100 Ethernet MAC integrated (vs PIC32MX575F256LT-80I/BG)
- Larger 64 KB SRAM versus 32 KB on PIC32MX664 family (vs PIC32MX664F128LT-I/BG)
- Free MPLAB Harmony and XC32 compiler support (vs PIC32MX360F256LT-80I/BG)
Notes de conception
The 121-ball TFBGA package uses 0.8 mm ball pitch which requires 4-layer PCB routing with microvia-in-pad or dogbone fanout. Use Microchip's recommended 0.4 mm escape traces, 0.2 mm via drill and 0.4 mm via pad. Place 0.1 µF X7R 0402 decoupling capacitors adjacent to each VDD/VSS ball pair, plus 4.7 µF bulk capacitors near each corner. Maintain a continuous ground reference under the BGA for SI and EMI performance per Microchip AN1255 PCB layout guidelines.
Do not omit the ICSP programming footprint on production PCBs - the PIC32MX775F256LT-80I/BG requires ICSP for firmware loading even if JTAG is present. Reserve at minimum PGECx/PGEDx test points plus MCLR pull-up to VDD via 10 kΩ. The 80 MHz prefetch cache must be enabled in the system configuration register before Flash execution at zero wait states; otherwise code runs at half speed per the PIC32MX5/6/7 family errata DS80000471H.
Estimated: at maximum core activity (80 MHz, all peripherals active, 3.6 V VDD) the PIC32MX775F256LT-80I/BG draws approximately 70-110 mA total. Power dissipation is approximately 250-400 mW; the 121-ball TFBGA package has thermal resistance θJA of approximately 30 C/W on 4-layer JEDEC EIA/JESD51 test board, yielding a self-heating rise of 8-12 C above ambient. For industrial -40 °C to +85 °C operation, ensure ambient + self-heating stays below the maximum 85 °C rating. Operational decoupling to minimum 2.3 V VDD and Sleep mode reduces idle power to approximately 50 µA per the family reference manual.
Route Ethernet MII/RMII signals with controlled impedance (50 Ω single-ended to ground reference) and length-matching per the MII/RMII specification. Use a series 33 Ω damping resistor on each MII output if signal integrity issues arise. Place the Ethernet PHY within 100 mm of the MCU with the clock trace length matched within 25 mm. For USB Full-Speed signals, maintain 90 Ω differential impedance on D+/D- per the USB 2.0 specification and place the USBLC6 ESD protection within 5 mm of the connector.
Informations de conformité
RoHS compliant per Microchip product page (BG suffix indicates lead-free TFBGA). Industrial -80I temperature grade meets -40 °C to +85 °C; for AEC-Q100 automotive qualification, choose the PIC32MX775F256LT-I/BG-V automotive variant (refer to Microchip automotive datasheet DS80000471H). REACH compliance per Microchip product declaration.
