SN74HC244N - 8-Channel 3-State Buffer | Texas Instruments
MPN: SN74HC244N ✓ פעילSN74HC244N סקירה
A logic buffer is a digital semiconductor that strengthens or isolates signals traveling between circuit sections. A three-state buffer can present a logic 0, a logic 1, or a high-impedance output. This output-state control makes the SN74HC244N useful for shared buses because multiple drivers can share conductors when their output-enable signals are mutually exclusive. Within the broader hierarchy, it is a CMOS logic IC, a bus-interface buffer, a line driver, and a member of the 74HC family.
The SN74HC244N provides eight non-inverting channels, two independently controlled four-output groups, and operation from 2 V to 6 V. Its three-state outputs support bus-oriented receivers and transmitters, memory-address drivers, and clock drivers. Because the outputs can be disconnected electrically, the device helps prevent one driver from fighting another when several devices share a bus. The two-section organization also allows a designer to enable a four-bit group while holding the other group at high impedance.
The device uses positive-edge-triggered-style control conventions only in the sense that its output-enable inputs are level-sensitive; the enable state, rather than a data transition, determines whether outputs are active. The manufacturer describes the SNx4HC244 family as optimized for the performance and density of three-state memory-address drivers, clock drivers, and bus-oriented receivers and transmitters. The non-inverting architecture avoids changing the logical polarity of data passing through the device.
Typical applications include bidirectional-bus isolation, memory and peripheral address buffering, clock distribution, instrumentation interfaces, and control systems where several devices may connect to a shared conductor. The SN74HC244N is particularly useful when two four-bit output groups need independent enable control. Designers should still verify timing, output-drive capability, and system-specific fanout against the manufacturer datasheet for the operating condition being implemented.
A key design consideration is output-enable management. Only one driver should actively drive a shared net at a time; disabled outputs must remain at high impedance. Place the device close to the driven bus when trace length or propagation delay matters, and use a continuous ground plane with short supply connections. The 20-pin PDIP package also requires adequate through-hole spacing and assembly clearance from adjacent components.
This product page consolidates the manufacturer function description, package identification, technical specifications, drop-in alternatives, comparison points, and practical interface-design guidance into one engineering reference for evaluating the SN74HC244N in modern and legacy CMOS logic systems.
חלופות תחליף ישיר עבור SN74HC244N — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
74HC244N
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
MC74HC244N
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
CD74HC244N
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
74HC244N
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
TC74HC244N
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
SN74HC244N דירוגים מרביים ומאפיינים חשמליים
| Logic Type | Octal buffer and line driver |
| Number of Channels | 8 channels |
| Number of Elements | 2 elements |
| Bits per Element | 4 bits per element |
| סוג פלט | 3-state output |
| Signal Polarity | Non-inverting |
| Output-enable Control | 2 independent 4-output groups |
| Supply Voltage Range | 2 V to 6 V |
| Logic Family | 74HC CMOS |
| Package Type | 20-pin PDIP |
| Total Pin Count | 20 pins |
| סוג הרכבה | Through-hole |
מדריך תצורת פינים של SN74HC244N 20-pin pdip
תצורת פינים עבור SN74HC244N (מארזת 20-pin pdip). מעגל משולב דיגיטלי זה כולל GPIO, ממשקי תקשורת (UART, SPI, I2C) ופיני מתח. יש לעיין בגיליון הנתונים של היצרן לפונקציות פינים חלופיות ולאפשרויות תצורה. חיוני לתכנון מערכות משובצות ולפריסת PCB.
אין נתוני פריסת פינים מפורטים עבור SN74HC244N.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
SN74HC244N מתאים עבור 6 יישוםs: Shared-Bus Signal Isolation, Memory Address Buffering, Clock Signal Distribution, Instrumentation Interface, Industrial Control Backplane, Legacy Peripheral Bus Isolation.
Shared-Bus Signal Isolation
The SN74HC244N fits shared-bus isolation because its eight non-inverting channels can drive four conductors per section and enter a high-impedance state when the associated output-enable input is high. This allows multiple buffer devices to share address or control lines without two active drivers continuously fighting each other. Texas Instruments identifies three-state memory-address and bus-oriented drivers as core applications. The 2 V to 6 V operating range supports both lower-voltage CMOS systems and conventional 5 V logic. The key design requirement is correct enable sequencing: only one driver should actively drive a given net at a time. Pull resistors may be added where the system requires a defined state during reset or when every driver is disabled.
מומלץ
Memory Address Buffering
The SN74HC244N is appropriate for memory-address buffering because it provides eight non-inverting buffers with three-state outputs and two independently enabled four-bit groups. The two sections can connect address lines to different devices, buses, or operating regions while allowing unused outputs to remain disconnected. Its use of non-inverting paths preserves the logical address presented by the controlling circuit. For a design operating from 2 V to 6 V, timing must be checked against the actual supply voltage and load because propagation delay changes with operating conditions. Engineers should also compare the target memory's enable timing with the buffer's output-enable delay to prevent address overlap during transitions.
מומלץ
Clock Signal Distribution
The SN74HC244N can distribute a clock to multiple destinations because each of its eight non-inverting channels provides a dedicated buffered output, while two output-enable groups can be controlled independently. The buffered paths reduce loading on the original clock source when the destination count and edge-rate requirements are suitable. Texas Instruments explicitly lists clock drivers among the intended uses of the SNx4HC244 family. Because the device includes three-state outputs, the clock can also be disconnected from selected destinations when bus contention or test modes require it. Validate propagation delay, output rise and fall time, and capacitive loading at the intended VCC before treating the buffer as transparent to every clock edge.
מומלץ
Instrumentation Interface
The SN74HC244N is useful in instrumentation and control interfaces where multiple digital lines must reach a connector, isolated circuit section, or acquisition module without excessive source loading. Eight non-inverting channels provide a convenient one-to-one signal path, and the two four-bit output-enable groups allow a diagnostic or maintenance bus segment to be disconnected under software control. Operation across 2 V to 6 V supports integration with both legacy 5 V logic and modern low-voltage CMOS interface rails. For sensitive measurement equipment, confirm noise, timing, and leakage characteristics in the manufacturer datasheet at the selected supply voltage, and use controlled grounding to prevent output switching from disturbing nearby analog circuitry.
מומלץ
Industrial Control Backplane
The SN74HC244N can support industrial control backplanes that distribute command, address, or interlock signals among several circuit cards. Its three-state outputs allow a card or bus segment to be electrically detached, while separate four-output enable groups simplify partial bus isolation. The non-inverting behavior avoids adding logic inversion to the system architecture, and the 20-pin PDIP package is suitable for through-hole industrial assemblies where manual maintenance and socketed prototyping remain common. In a deployed system, choose pull-up or pull-down values for disabled outputs, maintain a continuous ground plane, and verify timing at the highest voltage and temperature planned for the equipment.
מומלץ
Legacy Peripheral Bus Isolation
The SN74HC244N is well suited to isolating a legacy peripheral bus from a newer controller while preserving standard CMOS logic polarity. Eight channels can buffer read, write, address, or control signals, and each four-channel section can be disabled without removing all peripheral connections. This capability supports board redesigns, test fixtures, and systems that combine older peripheral ICs with newer control electronics. The designer must ensure that disabled outputs do not introduce a contention path, that every receiver interprets the high-impedance interval correctly, and that propagation delay does not violate setup and hold requirements. For a direct cross-manufacturer replacement, verify the package, pinout, supply range, timing, and output-drive capability rather than relying on the 74HC244 function name alone.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור SN74HC244N — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | 74HC244N | MC74HC244N | CD74HC244N | 74HC244N | TC74HC244N |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | NXP | onsemi | Renesas Electronics | Nexperia | Toshiba |
| Package | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP |
| Function | Octal non-inverting buffer and line driver | Octal non-inverting buffer and line driver | Octal non-inverting buffer and line driver | Octal non-inverting buffer and line driver | Octal non-inverting buffer and line driver | Octal non-inverting buffer and line driver |
| Number of Channels | 8 channels | 8 channels | 8 channels | 8 channels | 8 channels | 8 channels |
| Output Type | 3-state output | 3-state output | 3-state output | 3-state output | 3-state output | 3-state output |
| Signal Polarity | Non-inverting | Non-inverting | Non-inverting | Non-inverting | Non-inverting | Non-inverting |
| Supply Voltage Range | 2 V to 6 V | 2 V to 6 V | 2 V to 6 V | 2 V to 6 V | 2 V to 6 V | 2 V to 6 V |
| Output-enable Organization | Two independent 4-output groups | Two independent 4-output groups | Two independent 4-output groups | Two independent 4-output groups | Two independent 4-output groups | Two independent 4-output groups |
מבדילים עיקריים
- Two independently controllable four-output groups (לעומתNXP 74HC244N)
- Exact 20-pin PDIP orderable configuration (לעומתonsemi MC74HC244N)
- Broad 2 V to 6 V CMOS operating range (לעומתRenesas Electronics CD74HC244N)
הערות תכנון
Do not permit two active drivers to control the same bus conductor simultaneously. The SN74HC244N has two output-enable groups, each covering four outputs, so derive each enable from the same arbitration logic that grants bus ownership. Include defined pull-up or pull-down states where receivers must not see a floating input while all buffers are disabled. Review the complete enable and data sequence for overlap at power-up, reset, and mode changes.
Check propagation delay, output transition time, and capacitive-load limits at the actual supply voltage rather than relying on a single headline value. The 2 V to 6 V range allows operation across multiple CMOS voltage domains, but timing changes with VCC. For longer traces or fast clock distribution, place the buffer close to the source or receiver, minimize stub lengths, and maintain a continuous return path to reduce ringing and crosstalk.
Route supply and ground connections directly to the IC with short, low-impedance traces. Because the SN74HC244N is a 20-pin PDIP, preserve adequate through-hole spacing for connector leads, wave-solder fixtures, and rework tools. Place any bus pull resistors close to the receivers so that disabled outputs and unconnected lines settle quickly. Keep unrelated switching nodes away from clock and address outputs to avoid coupling into the buffered signals.
מידע על תאימות
No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was included in the manufacturer product-page result. Automotive qualification is not applicable to the standard SN74HC244N orderable MPN.