SN74HC245N - 8-Bit 3-State Bus Transceiver | Texas Instruments
MPN: SN74HC245N ✓ פעילSN74HC245N סקירה
A bus transceiver is a digital logic device that connects two buses while controlling signal direction and output impedance. The SN74HC245 belongs to the 74HC high-speed CMOS logic family, which operates at voltages compatible with both CMOS and low-power Schottky TTL systems. Its non-inverting data paths preserve logic polarity, while the three-state outputs can be disabled to create high-impedance bus segments for shared-bus applications.
Key features include eight independently controlled data channels, one common direction-control input, and one common output-enable input. The direction input determines whether data travels from the A bus to the B bus or in the reverse direction. When the output-enable input is active, all eight outputs are disabled simultaneously, allowing several transceivers to share a bus without contention. The high-current output stage can drive 15 LSTTL loads directly.
The SN74HC245N uses CMOS-compatible inputs and three-state outputs to support bus interface designs in industrial control, instrumentation, computer peripherals, and embedded systems. Its control-function implementation reduces external timing requirements during asynchronous communication. Because all eight channels share direction and enable control, the device is especially useful where an entire byte must change direction or be removed from a multidrop bus as a group.
Typical applications include isolating processor and peripheral buses, buffering data between circuit modules, implementing bidirectional parallel interfaces, and adding controlled impedance to shared backplanes. The same transceiver concept is also used in bus repeaters, test equipment, data acquisition systems, and legacy parallel-port interfaces. The 20-pin PDIP package supports through-hole assembly and easy prototyping.
When laying out a circuit, keep the direction and output-enable traces away from high-current or switching-node paths, and treat all unused inputs as required to be driven to a valid logic level. Decoupling should follow the manufacturer datasheet recommendations, with the supply capacitor placed close to the IC. Validate bus contention, signal timing, and level compatibility before substituting a device from another HC family.
This page combines the manufacturer device description, package details, operating characteristics, practical bus-interface guidance, and verified cross-reference information to support design selection. The alternatives and comparison sections focus on pin-compatible devices rather than functionally similar components that would require PCB changes.
חלופות תחליף ישיר עבור SN74HC245N — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם SN74HC245N (אותו גורם צורה וטביעת רגל) — שונים ב Data Direction, Direction Control, Output Enable, Output State, Product Type.
74HC245N
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
SN74HC245N דירוגים מרביים ומאפיינים חשמליים
| Product Type | 8-bit non-inverting bus transceiver |
| Number of Data Channels | 8 channels |
| Data Direction | Bidirectional |
| Output State | 3-state |
| Supply Voltage Range | 2 V to 6 V |
| Maximum Supply Voltage | 6 V |
| Maximum Quiescent Supply Current | 80 µA |
| Output Drive Capability | 15 LSTTL loads |
| Logic Family | 74HC high-speed CMOS |
| Input Compatibility | CMOS and LSTTL compatible |
| Direction Control | 1 common DIR input |
| Output Enable | 1 common OE input |
| Package Type | 20-pin PDIP |
| סגנון הרכבה | Through-hole |
תצורת פינים של SN74HC245N
| פין 1 | DIR — Direction-control input |
| פין 2 | 1B — B-side data input or output for channel 1 |
| פין 3 | 2B — B-side data input or output for channel 2 |
| פין 4 | 3B — B-side data input or output for channel 3 |
| פין 5 | 4B — B-side data input or output for channel 4 |
| פין 6 | 5B — B-side data input or output for channel 5 |
| פין 7 | 6B — B-side data input or output for channel 6 |
| פין 8 | 7B — B-side data input or output for channel 7 |
| פין 9 | GND — Ground reference |
| פין 10 | OE — Active-low output-enable input |
| פין 11 | 1A — A-side data input or output for channel 1 |
| פין 12 | 2A — A-side data input or output for channel 2 |
| פין 13 | 3A — A-side data input or output for channel 3 |
| פין 14 | 4A — A-side data input or output for channel 4 |
| פין 15 | 5A — A-side data input or output for channel 5 |
| פין 16 | 6A — A-side data input or output for channel 6 |
| פין 17 | 7A — A-side data input or output for channel 7 |
| פין 18 | 8B — B-side data input or output for channel 8 |
| פין 19 | VCC — Positive supply voltage |
| פין 20 | 8A — A-side data input or output for channel 8 |
יישומים טיפוסיים
SN74HC245N מתאים עבור 6 יישוםs: Bidirectional Instrument Bus, Embedded Processor Bus Isolation, Data Acquisition Backplane, Computer Peripheral Interface, Industrial Control Module, Test and Measurement Interface.
Bidirectional Instrument Bus
The SN74HC245N fits legacy laboratory and industrial instrument buses where a controller must exchange eight parallel data bits with a peripheral while avoiding driver contention. Its 2 V to 6 V operating range supports the 74HC logic environment, and its three-state outputs can disconnect all eight paths from a shared bus. According to the Texas Instruments manufacturer datasheet, the high-current output stage can drive 15 LSTTL loads directly. Place the transceiver close to the bus connector or logic device, route the DIR and output-enable signals as short controlled traces, and verify setup, hold, and propagation-delay margins at the slowest supported system clock. The main tradeoff is that this is a parallel, single-voltage transceiver rather than a modern differential or level-shifting interface.
מומלץ
Embedded Processor Bus Isolation
The SN74HC245N can place an 8-bit processor or peripheral bus behind a controlled three-state buffer, reducing contention between multiple bus masters. The DIR input selects the communication direction, while the common output-enable input can isolate the device when another controller owns the bus. Its non-inverting logic preserves data polarity, and the 20-pin PDIP package supports through-hole prototyping. According to the Texas Instruments manufacturer datasheet, the output stage can drive 15 LSTTL loads. In a multi-master design, ensure that only one transceiver asserts its outputs at a time and that enable timing accounts for the device’s propagation delay. For long, high-speed buses, add controlled impedance or a dedicated transceiver rather than relying only on the logic output.
מומלץ
Data Acquisition Backplane
The SN74HC245N is useful on parallel data-acquisition backplanes that require a short bidirectional link between measurement logic and a controller. The common direction and output-enable controls simplify management of a shared eight-bit data bus, while the three-state outputs allow the node to become electrically inactive during another module’s transmission. According to the Texas Instruments manufacturer datasheet, the device supports operation from 2 V to 6 V and can drive 15 LSTTL loads. Keep the transceiver’s supply return close to the logic ground and minimize the distance between its pins and the protected backplane connector. Engineers should verify input thresholds, output drive, timing, and fanout against the acquisition system’s actual load, especially when cable capacitance raises edge-rate requirements.
מומלץ
Computer Peripheral Interface
The SN74HC245N supports legacy parallel computer peripherals that exchange an entire byte over shared wires and require a way to relinquish the bus. A DIR-controlled eight-bit path can connect a host adapter to a printer, storage controller, or external test module, while the output-enable input provides a controlled high-impedance state during turnaround. According to the Texas Instruments manufacturer datasheet, the transceiver is designed for asynchronous two-way communication and minimizes external timing requirements. The logic family’s CMOS-compatible supply range also supports integration with 74HC controllers. Care is needed at connectors and cable transitions because the SN74HC245N is intended for logic-level bus loading, not long-distance differential communication; add series damping or a physical-layer transceiver when cable length or ground offsets become significant.
מומלץ
Industrial Control Module
The SN74HC245N can bridge a PLC or embedded controller to a parallel I/O module in an industrial system while allowing the bus to be disabled during maintenance or controller handoff. Its 8-bit bidirectional architecture and common control signals simplify board-level bus partitioning, while the 6 V maximum supply and LSTTL drive capability support conventional industrial logic levels. According to the Texas Instruments manufacturer datasheet, the transceiver can operate across the 74HC supply range and drive 15 LSTTL loads. Use its three-state behavior only after confirming that all connected nodes use compatible voltage thresholds. Protect external connectors as appropriate for the installation environment, and validate timing over the full operating-temperature range because propagation delay and output characteristics can vary with supply voltage and temperature.
מומלץ
Test and Measurement Interface
The SN74HC245N can connect test logic to a bench instrument or fixture through an eight-bit parallel command and response bus. The common direction control makes command/response turnaround straightforward, and the three-state outputs let the fixture release the bus when a different tester or external fixture is connected. According to the Texas Instruments manufacturer datasheet, the device is designed for asynchronous two-way communication and its output stage can drive 15 LSTTL loads. Keep the transceiver close to the logic connector, provide a low-impedance supply return, and avoid routing the bus beside switching converters or high-current relays. For high-speed automated test systems, account for propagation delay and bus-turnaround time rather than assuming the direction change is instantaneous.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור SN74HC245N — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | 74HC245N |
|---|---|---|
| Brand | Texas Instruments | Nexperia |
| Package | 20-pin PDIP | 20-pin PDIP |
| Function | Octal non-inverting bus transceiver | Octal non-inverting bus transceiver |
| Number of Channels | 8 channels | 8 channels |
| Output State | 3-state | 3-state |
| Direction Control | Common DIR input | Common DIR input |
| Output Enable | Common active-low OE input | Common output-enable input |
מבדילים עיקריים
- Manufacturer-specific Texas Instruments implementation (לעומת74HC245N)
- Complete byte-level direction control (לעומת74HC245N)
- Common three-state bus release (לעומת74HC245N)
הערות תכנון
Never allow two bus nodes to drive the same line simultaneously. Assert the SN74HC245N output-enable input only after every conflicting transceiver has entered its high-impedance state, and include bus-turnaround time in the control timing. The DIR and OE signals must not be allowed to float because unpredictable control states can produce contention or unintended data transfer.
Place the decoupling capacitor close to the VCC and GND pins and provide a low-impedance ground return. Keep the DIR and OE traces short and route them away from switching nodes, relay coils, and high-current outputs. For exposed connectors or long bus branches, use controlled rise times and termination appropriate to the board topology rather than adding large capacitive loads directly to every channel.
Validate propagation delay, setup and hold timing, output drive, and input thresholds at the actual supply voltage. The 6 V maximum operating voltage does not imply that 6 V logic thresholds apply equally at every lower supply. Also confirm the load count and bus capacitance because the 15 LSTTL-load capability describes drive strength, not unlimited cable length or guaranteed timing margin at every frequency.
Use only the supply range and decoupling arrangement specified by the Texas Instruments manufacturer datasheet. Although the maximum quiescent supply current is 80 µA, installed-system consumption can increase substantially when the outputs switch or drive external loads. Evaluate the complete circuit’s supply budget and ensure the regulator can support the dynamic current associated with eight simultaneously changing bus lines.
מידע על תאימות
The device is a general-purpose commercial logic IC, not an automotive-qualified part. Compliance declarations were not identified in the available manufacturer-page excerpts and must be confirmed from the current Texas Instruments product page or applicable material-declaration documents.