SN65HVD53D vs SN65HVD51D तुलना
विस्तृत दोनों ओर की तुलना SN65HVD53D द्वारा Texas Instruments और SN65HVD51D द्वारा Texas Instruments. मुख्य विशेषताओं, इलेक्ट्रिकल पैरामीटर, पैकेजिंग, चक्र स्थिति, मूल्यांकन और उपलब्धता को तुलना करके अपनी डिजाइन की आवश्यकताओं के लिए सबसे अच्छा घटक निर्धारित करें。
Texas Instruments
SN65HVD53D - High-Output Full-Duplex RS-485 Transceiver | Texas Instruments
SN65HVD53D ✓ सक्रियTexas Instruments
SN65HVD51D - 5Mbps Full-Duplex RS-485 Transceiver | Texas Instruments
SN65HVD51D ✓ सक्रियविशेषता तुलना
| पैरामीटर | SN65HVD53D | SN65HVD51D |
|---|---|---|
| ब्रांड | Texas Instruments | Texas Instruments |
| श्रेणी | Interface ICs | Interface ICs |
| लाइफसाइकिल स्थिति | सक्रिय | सक्रिय |
| Device Type | Full-duplex RS-485 / RS-422 transceiver with enables | — |
| Number of Drivers / Receivers | 1 / 1 | — |
| Driver Enable Polarity | Active-high | — |
| Receiver Enable Polarity | Active-low | — |
| Unit Load Option | 1/8 unit-load option available (up to 256 nodes on the bus) | — |
| Maximum Nodes on Bus | 256 nodes | — |
| Bus Pin ESD Protection | Exceeds 15 kV HBM | — |
| Driver Output Transition Time Options | 1 Mbps, 5 Mbps and 25 Mbps signaling rates | — |
| Standby Current | 1 uA (both driver and receiver disabled) | Less than 1 µA |
| Receiver Output | Glitch-free | — |
| Standards Supported | RS-485, RS-422 | — |
| Supply Voltage Range | [DATA_NEEDED: supply voltage range] | 4.5 V to 5.5 V |
| Maximum Data Rate (this device) | [DATA_NEEDED: maximum data rate for SN65HVD53D] | — |
| Driver Output Current | [DATA_NEEDED: high-output driver current] | — |
| Receiver Sensitivity | [DATA_NEEDED: receiver input sensitivity] | — |
| ऑपरेटिंग तापमान रेंज | -40 C to +85 C | -40 °C to 85 °C |
| पैकेज | SOIC (D), 14 pins, 3.90 mm width, 0.154 inch pitch | 8-pin SOIC (D) |
| माउंटिंग प्रकार | Surface mount | Surface mount |
| RoHS स्थिति | [DATA_NEEDED: RoHS status] | [DATA_NEEDED: RoHS compliance status] |
| Product Type | — | RS-422/RS-485 full-duplex transceiver |
| Driver Count | — | 1 driver |
| Receiver Count | — | 1 receiver |
| Maximum Signaling Rate | — | 5 Mbps |
| Interface Standards | — | RS-422 and RS-485 |
| Duplex Mode | — | Full-duplex |
| Receiver Unit Load | — | 1/8 unit load |
| Maximum Bus Nodes | — | Up to 256 nodes |
| Bus-Pin ESD Protection | — | Exceeds 15 kV HBM |
| Available Driver Transition Rates | — | 1 Mbps, 5 Mbps, and 25 Mbps |
| Enable Architecture | — | Fully enabled; no external enable pins |
| REACH Status | — | [DATA_NEEDED: REACH compliance status] |