STM32F407VET6 - 168MHz Cortex-M4 MCU 512KB Flash LQFP-100 | ST
MPN: STM32F407VET6 ✓ Aktif| Kwantitas | Harga Satuan | Lengkap |
|---|---|---|
| 1 | $6.1875 | $6,19 |
| 10 | $4.4688 | $44,69 |
| 100 | $3.9531 | $395,31 |
| 500 | $3.7813 | $1.890,65 |
| 1.000 | $3.6094 | $3.609,40 |
STM32F407VET6 Ringkasan
What is a microcontroller? A microcontroller (MCU) is a single-chip integrated circuit that combines a processor core, non-volatile program memory (Flash), volatile working memory (SRAM), and programmable peripherals to govern specific operations in embedded systems. The STM32F407VET6 belongs to the STM32F4 series built on the ARM Cortex-M4 core with FPU, positioned within the broader hierarchy of 32-bit MCUs - microcontroller in the embedded semiconductor taxonomy used in supply chains.
Key features include an on-chip 10/100 Ethernet MAC with IEEE 1588v2, USB 2.0 OTG Full-Speed and High-Speed with PHY, a digital camera interface (DCMI), three 12-bit ADCs with up to 24 channels and 2.4 MSPS, dual 12-bit DACs, an SDIO interface, FSMC for external memory, a crypto/hash peripheral, and a rich set of timers, USART, SPI, I2C, and CAN interfaces. The supply range is 1.8V to 3.6V with operation from -40C to +85C.
Technically, the STM32F407VET6 uses a Harvard bus architecture with separate instruction and data buses enabling simultaneous fetch and access, an ART Accelerator with 128-bit Flash prefetch eliminating wait states from Flash, a memory protection unit (MPU), and a nested vectored interrupt controller (NVIC) supporting deterministic real-time behavior. The single-precision FPU accelerates math-intensive firmware for control loops and DSP.
Typical applications include industrial motor control and PLCs, networked IoT gateways using the on-chip Ethernet MAC, USB device and host designs, and machine-vision or imaging systems using the DCMI camera interface.
Design tip: decouple every VDD pin with 100 nF ceramics plus bulk capacitance, route VDDA/VSSA on a clean analog plane to minimize ADC noise, and place the HSE crystal as close as possible with proper guard rings for stable clocking.
This page synthesizes distributor pricing, drop-in alternatives, and practical design considerations not found in the standalone manufacturer datasheet, including LQFP-100 same-footprint cross references and companion MPNs for reference designs.
Alternatif penggantian untuk STM32F407VET6 — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian STM32F407VET6 (sama faktor bentuk dan footprint) — berbeda di dalam Package, SRAM, ADC, Communication Interfaces, Mounting Type.
Alat Perbandingan Cepat — Pilih bagian alternatif untuk perbandingan paralel:
STM32F407VGT6
✗ Habis Stok
$7.55 / Satuan
Lihat Datasheet →STM32F405VGT6
Kontak untuk harga
Lihat Datasheet →STM32F427VIT6
✗ Habis Stok
$10.5 / Satuan
Lihat Datasheet →STM32F417VIT6
📋 Alternatif referensi (tidak dalam katalog)
GD32F407VET6
📋 Alternatif referensi (tidak dalam katalog)
GD32F407VGT6
📋 Alternatif referensi (tidak dalam katalog)
STM32F407VET6 Rating Maksimal & Karakteristik Listrik
| Core Architecture | ARM Cortex-M4F (32-bit RISC with FPU) |
| Frekuensi Bawah Maximum | 168 MHz |
| Program Memory (Flash) | 512 KB |
| SRAM | 192 KB |
| Paket | LQFP-100 (14x14 mm) |
| Supply Voltage (VDD) | 1.8 V to 3.6 V |
| Suhu Kerja | -40C to +85C |
| Lebar Bus Data | 32 bit |
| ADC | 3 x 12-bit, up to 24 input channels |
| DAC | 2 x 12-bit |
| Communication Interfaces | USB OTG HS/FS, Ethernet MAC, 3x SPI, 3x I2C, 4x USART, 2x UART, 2x CAN, SDIO |
| Camera Interface | DCMI (Digital Camera Interface) |
| Tipe Mounting | Surface Mount (SMD/SMT) |
| Level MSL | 3 (168 hours) |
| Status RoHS | Compliant |
| External Memory Bus | FSMC (Flexible Static Memory Controller) |
Konfigurasi Pin STM32F407VET6
| Pin produk 1 | PE2 — GPIO PE2 / TRACECLK / FSMC_A23 |
| Pin produk 2 | PE3 — GPIO PE3 / TRACED0 / FSMC_A19 |
| Pin produk 3 | PE4 — GPIO PE4 / TRACED1 / FSMC_A20 |
| Pin produk 4 | PE5 — GPIO PE5 / TRACED2 / FSMC_A21 |
| Pin produk 5 | PE6 — GPIO PE6 / TRACED3 / FSMC_A22 |
| Pin produk 6 | VBAT — Battery backup supply for RTC and backup registers |
| Pin produk 7 | PC13 — GPIO PC13 / RTC_TAMP1 / RTC_OUT / RTC_TS |
| Pin produk 8 | PC14 — GPIO PC14 / OSC32_IN |
| Pin produk 9 | PC15 — GPIO PC15 / OSC32_OUT |
| Pin produk 10 | VSS — Digital ground |
| Pin produk 11 | VDD — Digital supply (1.8V-3.6V) |
| Pin produk 12 | OSC_IN — HSE oscillator input |
| Pin produk 13 | OSC_OUT — HSE oscillator output |
| Pin produk 14 | NRST — Reset input (active low) |
| Pin produk 15 | PC0 — GPIO PC0 / ADC10_IN10 |
| Pin produk 16 | PC1 — GPIO PC1 / ADC11_IN11 |
| Pin produk 17 | PC2 — GPIO PC2 / ADC12_IN12 |
| Pin produk 18 | PC3 — GPIO PC3 / ADC13_IN13 |
| Pin produk 19 | VSSA — Analog ground |
| Pin produk 20 | VDDA — Analog supply (1.8V-3.6V) |
| Pin produk 21 | PA0/WKUP — GPIO PA0 / WKUP / ADC0_IN0 / TIM2_CH1 |
| Pin produk 22 | PA1 — GPIO PA1 / ADC1_IN1 / TIM2_CH2 |
| Pin produk 23 | PA2 — GPIO PA2 / ADC2_IN2 / TIM2_CH3 / USART2_TX |
| Pin produk 24 | PA3 — GPIO PA3 / ADC3_IN3 / TIM2_CH4 / USART2_RX |
| Pin produk 25 | VSS — Digital ground |
| Pin produk 26 | VDD — Digital supply |
| Pin produk 27 | PA4 — GPIO PA4 / ADC4_IN4 / DAC_OUT1 / SPI1_NSS |
| Pin produk 28 | PA5 — GPIO PA5 / ADC5_IN5 / DAC_OUT2 / SPI1_SCK |
| Pin produk 29 | PA6 — GPIO PA6 / ADC6_IN6 / SPI1_MISO / TIM13_CH1 |
| Pin produk 30 | PA7 — GPIO PA7 / ADC7_IN7 / SPI1_MOSI / TIM14_CH1 |
| Pin produk 31 | PC4 — GPIO PC4 / ADC14_IN14 |
| Pin produk 32 | PC5 — GPIO PC5 / ADC15_IN15 |
| Pin produk 33 | PB0 — GPIO PB0 / ADC8_IN8 / TIM3_CH3 |
| Pin produk 34 | PB1 — GPIO PB1 / ADC9_IN9 / TIM3_CH4 |
| Pin produk 35 | PB2 — GPIO PB2 / BOOT1 |
| Pin produk 36 | PE7 — GPIO PE7 / FSMC_D4 |
| Pin produk 37 | PE8 — GPIO PE8 / FSMC_D5 |
| Pin produk 38 | PE9 — GPIO PE9 / FSMC_D6 |
| Pin produk 39 | PE10 — GPIO PE10 / FSMC_D7 |
| Pin produk 40 | PE11 — GPIO PE11 / FSMC_D8 |
| Pin produk 41 | PE12 — GPIO PE12 / FSMC_D9 |
| Pin produk 42 | PE13 — GPIO PE13 / FSMC_D10 |
| Pin produk 43 | PE14 — GPIO PE14 / FSMC_D11 |
| Pin produk 44 | PE15 — GPIO PE15 / FSMC_D12 |
| Pin produk 45 | PB10 — GPIO PB10 / I2C2_SCL / USART3_TX |
| Pin produk 46 | PB11 — GPIO PB11 / I2C2_SDA / USART3_RX |
| Pin produk 47 | VSS — Digital ground |
| Pin produk 48 | VDD — Digital supply |
| Pin produk 49 | PB12 — GPIO PB12 / SPI2_NSS / I2C2_SMBA / USBOTGHS_ID |
| Pin produk 50 | PB13 — GPIO PB13 / SPI2_SCK / USBOTGHS_VBUS |
| Pin produk 51 | PB14 — GPIO PB14 / SPI2_MISO / USBOTGHS_DM |
| Pin produk 52 | PB15 — GPIO PB15 / SPI2_MOSI / USBOTGHS_DP |
| Pin produk 53 | PD8 — GPIO PD8 / FSMC_D13 / USART3_TX |
| Pin produk 54 | PD9 — GPIO PD9 / FSMC_D14 / USART3_RX |
| Pin produk 55 | PD10 — GPIO PD10 / FSMC_D15 |
| Pin produk 56 | PD11 — GPIO PD11 / FSMC_A16 |
| Pin produk 57 | PD12 — GPIO PD12 / FSMC_A17 |
| Pin produk 58 | PD13 — GPIO PD13 / FSMC_A18 |
| Pin produk 59 | PD14 — GPIO PD14 / FSMC_D0 |
| Pin produk 60 | PD15 — GPIO PD15 / FSMC_D1 |
| Pin produk 61 | PC6 — GPIO PC6 / I2S2_MCK / TIM8_CH1 / SDIO_D6 |
| Pin produk 62 | PC7 — GPIO PC7 / I2S3_MCK / TIM8_CH2 / SDIO_D7 |
| Pin produk 63 | PC8 — GPIO PC8 / TIM8_CH3 / SDIO_D0 |
| Pin produk 64 | PC9 — GPIO PC9 / I2C3_SDA / SDIO_D1 |
| Pin produk 65 | PA8 — GPIO PA8 / I2C3_SCL / USART1_CK / MCO1 |
| Pin produk 66 | PA9 — GPIO PA9 / USART1_TX / TIM1_CH2 / USBOTGFS_VBUS |
| Pin produk 67 | PA10 — GPIO PA10 / USART1_RX / TIM1_CH3 / USBOTGFS_ID |
| Pin produk 68 | PA11 — GPIO PA11 / USART1_CTS / USBOTGFS_DM |
| Pin produk 69 | PA12 — GPIO PA12 / USART1_RTS / USBOTGFS_DP |
| Pin produk 70 | PA13 — GPIO PA13 / JTMS-SWDIO |
| Pin produk 71 | VSS — Digital ground |
| Pin produk 72 | VDD — Digital supply |
| Pin produk 73 | PA14 — GPIO PA14 / JTCK-SWCLK |
| Pin produk 74 | PA15 — GPIO PA15 / JTDI / SPI3_NSS |
| Pin produk 75 | PC10 — GPIO PC10 / UART4_TX / SDIO_D2 |
| Pin produk 76 | PC11 — GPIO PC11 / UART4_RX / SDIO_D3 |
| Pin produk 77 | PC12 — GPIO PC12 / UART5_TX / SDIO_CK |
| Pin produk 78 | PD0 — GPIO PD0 / FSMC_D2 / CAN1_RX |
| Pin produk 79 | PD1 — GPIO PD1 / FSMC_D3 / CAN1_TX |
| Pin produk 80 | PD2 — GPIO PD2 / UART5_RX / SDIO_CMD |
| Pin produk 81 | PD3 — GPIO PD3 / FSMC_CLK |
| Pin produk 82 | PD4 — GPIO PD4 / FSMC_NOE |
| Pin produk 83 | PD5 — GPIO PD5 / FSMC_NWE |
| Pin produk 84 | PD6 — GPIO PD6 / FSMC_NWAIT |
| Pin produk 85 | PD7 — GPIO PD7 / FSMC_NCE2 / FSMC_NE1 |
| Pin produk 86 | PB3 — GPIO PB3 / JTDO / SPI3_SCK / I2S3_CK |
| Pin produk 87 | PB4 — GPIO PB4 / NJTRST / SPI3_MISO |
| Pin produk 88 | PB5 — GPIO PB5 / I2C1_SMBA / SPI3_MOSI / I2S3_SD |
| Pin produk 89 | PB6 — GPIO PB6 / I2C1_SCL / TIM4_CH1 / USART1_TX |
| Pin produk 90 | PB7 — GPIO PB7 / I2C1_SDA / TIM4_CH2 / USART1_RX |
| Pin produk 91 | BOOT0 — Boot mode selection (main Flash / system memory / SRAM) |
| Pin produk 92 | PB8 — GPIO PB8 / TIM4_CH3 / I2C1_SCL / CAN1_RX |
| Pin produk 93 | PB9 — GPIO PB9 / TIM4_CH4 / I2C1_SDA / CAN1_TX |
| Pin produk 94 | PE0 — GPIO PE0 / TIM4_ETR / FSMC_NBL0 |
| Pin produk 95 | PE1 — GPIO PE1 / FSMC_NBL1 |
| Pin produk 96 | VSS — Digital ground |
| Pin produk 97 | VSS — Digital ground |
| Pin produk 98 | VDD — Digital supply |
| Pin produk 99 | VDD — Digital supply |
| Pin produk 100 | VSS — Digital ground |
Aplikasi Umum
STM32F407VET6 cocok untuk 6 aplikasis: Industrial Motor Control and PLCs, Networked IoT Gateway with Ethernet, USB Device, Host and OTG Designs, Machine Vision and Imaging Systems, Audio Processing and DSP, Data Acquisition and Industrial Instrumentation.
Industrial Motor Control and PLCs
The STM32F407VET6 is well-suited for industrial motor control and PLC platforms where deterministic real-time performance is required. Its 168 MHz Cortex-M4F core with FPU and DSP extensions accelerates Park/Clarke transforms used in field-oriented control (FOC) for PMSM and ACIM motors. Three 12-bit ADCs at up to 2.4 MSPS enable simultaneous current and voltage sensing on all three motor phases for high-bandwidth torque control loops. Advanced timers with complementary PWM outputs and programmable dead-time insertion directly drive half-bridge power stages such as the STGIPN3H60 or gate drivers. Industrial operating temperature from -40C to +85C supports factory floor deployments, while CAN interfaces (2x) integrate with industrial fieldbus networks. Companion MPNs include STGIPN3H60 IGBT module, ACS712 current sensor, and isolated CAN transceiver.
Direkomendasikan
Networked IoT Gateway with Ethernet
The STM32F407VET6 integrates a 10/100 Ethernet MAC with IEEE 1588v2 hardware timestamping that, paired with an external LAN8720A or DP83848 PHY, brings up a full TCP/IP gateway without an external Ethernet controller. Its 168 MHz Cortex-M4F core runs lwIP or similar stacks while reserving CPU headroom for application logic and TLS encryption accelerated by the on-chip crypto/hash peripheral. The 192 KB SRAM comfortably fits MQTT, CoAP, and TLS session buffers for typical edge gateway workloads, and the 512 KB Flash holds bootloader, application, and OTA staging partitions. USB OTG FS enables local configuration via mass storage or CDC, while SDIO supports local data logging. Companion MPNs include LAN8720A PHY, W25Q128JVSIQ NOR Flash for OTA, and TPS62135RGTR for power regulation.
Direkomendasikan
USB Device, Host and OTG Designs
The STM32F407VET6 includes both USB OTG Full-Speed (12 Mbps) and High-Speed (480 Mbps) controllers with on-chip PHYs, enabling USB device, host, and OTG roles without external components. HS USB with the integrated ULPI-less PHY supports high-throughput functions such as mass storage, CDC ACM, HID, and audio class devices at full USB 2.0 speeds for industrial peripherals and test instruments. The 168 MHz Cortex-M4F core handles USB stack processing, class drivers, and application code concurrently, while 192 KB SRAM buffers USB packets efficiently. VBUS sensing pins and integrated 5V-tolerance on D+/D- simplify USB-C connector interfaces when paired with FUSB302 chipset. Companion MPNs include FUSB302UCX USB-C controller, USBLC6-2SC6 ESD protection, and TPS73633DBVR LDO.
Direkomendasikan
Machine Vision and Imaging Systems
The STM32F407VET6 integrates a Digital Camera Interface (DCMI) that receives 8/10/12/14-bit parallel video streams from CMOS image sensors such as OV5640 or MT9V032, enabling cost-effective machine-vision and embedded imaging applications. The 168 MHz Cortex-M4F core runs JPEG/MJPEG compression, basic image processing, and feature extraction at video rates for applications like barcode scanning, optical inspection, and biometric capture. FSMC bus supports external SRAM or PSRAM buffering of full-resolution frames, while SDIO offloads captured images to SD cards at high speed. The camera interface synchronizes with on-chip timers for strobe/flash control. Companion MPNs include OV5640 image sensor, MT9V032 global shutter sensor, and IS42S16400F SDRAM for frame buffer.
Direkomendasikan
Audio Processing and DSP
The STM32F407VET6 is well-suited for audio DSP applications thanks to its single-precision FPU and DSP instruction extensions on the Cortex-M4F core. Audio CODECs such as SGTL5000, WM8994, or CS43L22 interface to the MCU via I2S, providing stereo line/microphone inputs, headphone output, and integrated PLLs for low-jitter clocking. The 168 MHz core runs sample rates up to 192 kHz with headroom for EQ, mixing, and effects processing in real time on multiple audio channels. Dual 12-bit DACs provide analog audio output for simpler designs, and the SDIO interface reads audio files from SD cards for stand-alone players. Companion MPNs include SGTL5000 audio codec, CS43L22 DAC, and TPA6130A2 headphone amplifier.
Direkomendasikan
Data Acquisition and Industrial Instrumentation
The STM32F407VET6 excels in multi-channel data acquisition systems where its three 12-bit ADCs (up to 24 channels, 2.4 MSPS total) capture analog signals simultaneously for power monitoring, condition monitoring, and instrumentation front-ends. The FPU and DSP extensions accelerate FFT-based frequency analysis for vibration, harmonic, and spectral measurements in industrial test equipment. FSMC interface supports external ADC converters (such as AD7606 16-bit) for higher resolution, while SDIO logs captured data to removable storage. The Ethernet MAC and USB OTG enable both bench-top SCPI-style instruments and networked remote data loggers. Industrial temperature rating of -40C to +85C supports factory floor installation. Companion MPNs include AD7606 16-bit ADC, AD620AN instrumentation amp, and TMP117 temperature sensor.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk STM32F407VET6 — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | STM32F407VGT6 | STM32F405VGT6 | STM32F417VIT6 | STM32F427VIT6 | GD32F407VET6 | GD32F407VGT6 |
|---|---|---|---|---|---|---|---|
| Package | LQFP-100 (14x14 mm) | LQFP-100 (14x14 mm) - same | LQFP-100 (14x14 mm) - same | LQFP-100 (14x14 mm) - same | LQFP-100 (14x14 mm) - same | LQFP-100 (14x14 mm) - same | LQFP-100 (14x14 mm) - same |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | GigaDevice | GigaDevice |
| Core / Clock | Cortex-M4F / 168 MHz | Cortex-M4F / 168 MHz | Cortex-M4F / 168 MHz | Cortex-M4F / 168 MHz | Cortex-M4F / 180 MHz | Cortex-M4F / 168 MHz | Cortex-M4F / 168 MHz |
| Flash | 512 KB | 1 MB | 1 MB | 1 MB | 2 MB | 512 KB | 1 MB |
| SRAM | 192 KB | 192 KB | 192 KB | 192 KB | 256 KB | 192 KB | 192 KB |
| Ethernet MAC | Yes | Yes | No | Yes | Yes | Yes | Yes |
| USB OTG HS | Yes | Yes | Yes (no PHY) | Yes (with crypto) | Yes | Yes | Yes |
| Crypto / Hash | No | No | No | Yes (AES, Hash, RNG) | Yes | No | No |
| SDRAM Interface | No (FSMC only) | No (FSMC only) | No (FSMC only) | No (FSMC only) | Yes (SDRAM) | No (FSMC only) | No (FSMC only) |
| DCMI Camera IF | Yes | Yes | No | Yes | Yes | Yes | Yes |
| Approx. Unit Price | $5.95 (qty 1000) | $7.50 (qty 1000) | $6.20 (qty 1000) | $8.90 (qty 1000) | $9.40 (qty 1000) | $3.50 (qty 1000) | $4.30 (qty 1000) |
Diferensiator Kunci
- Pin-compatible upgrade path with more Flash (vsSTM32F407VGT6)
- More memory than STM32F407VET6 in same LQFP-100 (vsSTM32F427VIT6)
- Cryptographic acceleration absent on STM32F407VET6 (vsSTM32F417VIT6)
- Cost-effective cross-brand second source (vsGD32F407VET6)
Catatan Desain
Decouple every VDD pin with a 100 nF X7R ceramic placed within 2 mm of the pin, plus a shared 4.7 uF bulk capacitor on each supply rail. The VDDA analog supply should be filtered with a ferrite bead from VDD and bypassed with 10 nF + 1 uF ceramics to minimize ADC noise. If VREF+ is used, drive it from a low-noise reference source; otherwise tie it to VDDA and accept the reduced ADC linearity. Refer to ST application note AN5031 for STM32F4 power-supply hardware design guidelines.
Place the 8 MHz HSE crystal within 5 mm of OSC_IN/OSC_OUT with symmetric traces and a ground guard ring. Route the 32.768 kHz LSE crystal traces short and away from switching nodes, with the load capacitors placed adjacent. Use a 4-layer PCB with continuous ground plane beneath the MCU; for LQFP-100, fan out signals on inner layers to maintain a low-impedance ground return path under the package. ESD protection (TVS arrays) should be placed near any external connector pins.
The STM32F407VET6 in LQFP-100 has a typical junction-to-ambient thermal resistance (theta_JA) of approximately 50 C/W depending on PCB copper area. For applications where the MCU runs near full 168 MHz with all peripherals active, design the ground copper pour under the package to at least 1 square inch to keep junction temperature below 100 C. The internal temperature sensor can be read by application firmware for thermal monitoring and dynamic clock throttling. Refer to ST datasheet DM00037051 for thermal characteristics.
Avoid leaving unused GPIO pins in floating input state; configure them as analog inputs to minimize current leakage. The BOOT0 pin must be held low for normal Flash boot; if left floating, the bootloader may enter system memory and stall. When using the integrated Ethernet MAC, ensure the external PHY is brought up before RMII/MII clock is enabled, or the MCU may hang during PHY initialization. Verify HSE crystal load capacitance matches the crystal specification - typical 8 MHz crystals need 10-20 pF load.
The high-speed USB OTG HS DP/DM traces must be 90 ohm differential impedance matched, length-matched within 150 mil, and routed over a continuous ground plane with no splits. For Ethernet RMII traces between MCU and external PHY, length-match the clock and data lines and keep traces under 50 mm. SDIO and FSMC bus signals should be length-matched within 1 inch when running at the maximum clock rate; place series damping resistors near the driver to control ringing.
Informasi Konformitas
RoHS and REACH compliant per STMicroelectronics product page DM00037051. Not AEC-Q100 qualified; for automotive grade, consider STM32F407VET7 or STM32F407VET6 automotive screening options. Lead-free and halogen-free per ST product certification.
