STM32F405RGT6 - 168MHz Cortex-M4F, 1MB Flash MCU | STMicroelectronics
MPN: STM32F405RGT6 ✓ AktifSTM32F405RGT6 Ringkasan
A microcontroller (MCU) is a compact integrated circuit that combines a processor core, volatile and non-volatile memory, and programmable peripherals on a single silicon die to govern specific operations in embedded systems. The STM32F405RGT6 belongs to the STM32F4 mainstream performance line, which sits within the broader STM32 family of 32-bit Flash microcontrollers. The category hierarchy is MCU -> 32-bit MCU -> ARM Cortex-M MCU -> Cortex-M4 MCU -> STM32F4 MCU. MCUs are the central control element in industrial, consumer, medical, and IoT electronics.
Key features include 3x 12-bit ADCs (2.4 MSPS), 2x 12-bit DACs, 12x 16-bit timers plus 2x 32-bit timers, 51 GPIOs, and rich connectivity: 3x I2C, 4x USART plus 2x UART, 3x SPI, 2x CAN, USB 2.0 OTG Full-Speed and High-Speed with on-chip PHY, 100Mbit Ethernet, SDIO, and a DCMI camera interface. The device operates from 1.8V to 3.6V and includes a true random-number generator, hardware CRC unit, and a 96-bit unique device ID.
Technically, the chip uses a 90 nm CMOS process with an ART Accelerator enabling zero-wait-state execution from Flash, maximizing effective Cortex-M4 throughput. A memory protection unit supports robust firmware isolation, while multiple low-power modes (Sleep, Stop, Standby with RTC) allow energy optimization for battery-powered designs. The integrated USB OTG HS PHY and Ethernet MAC eliminate external PHY BOM cost for many designs.
Typical applications include field-oriented-control motor drives (FOC servo drives leveraging the FPU and DSP instructions), digital power conversion and PFC stages, industrial PLC and automation controllers, USB peripherals and audio devices, and consumer/medical products requiring real-time signal processing. The open-source STM32CubeIDE and STM32CubeMX ecosystem with HAL/LL libraries significantly shortens development cycles.
Design consideration: provide adequate 100 nF decoupling on every VDD/VSS pin pair, route USB HS D+/D- as a 90-ohm differential pair, and keep SDIO traces length-matched. Also note that Flash wait states apply above 168 MHz if the ART accelerator configuration is altered.
This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet.
Alternatif penggantian untuk STM32F405RGT6 — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian STM32F405RGT6 (sama faktor bentuk dan footprint) — berbeda di dalam Core, Package, ADC, SRAM, Flash Memory.
STM32F415RGT6
Kontak untuk harga
Lihat Datasheet →STM32F405ZGT6
Kontak untuk harga
Lihat Datasheet →STM32F405VGT6
Kontak untuk harga
Lihat Datasheet →STM32F407VGT6
Kontak untuk harga
Lihat Datasheet →STM32F405RGT7
Kontak untuk harga
Lihat Datasheet →GD32F405RGT6
📋 Alternatif referensi (tidak dalam katalog)
STM32F405RGT6 Rating Maksimal & Karakteristik Listrik
| Core | ARM Cortex-M4F (with single-precision FPU and DSP) |
| Frekuensi Bawah Maximum | 168 MHz |
| Performance | 210 DMIPS (1.25 DMIPS/MHz) |
| Flash Memory | 1 MB (1M x 8) |
| SRAM | 192 KB (including 4 KB backup SRAM) |
| Operating Voltage | 1.8 V to 3.6 V |
| Paket | 64-LQFP (10x10 mm) |
| GPIO Count | 51 |
| ADC | 3x 12-bit, 2.4 MSPS, up to 24 channels |
| DAC | 2x 12-bit |
| Timers | 12x 16-bit + 2x 32-bit |
| Communication Interfaces | 3x I2C, 4x USART + 2x UART, 3x SPI, 2x CAN, USB OTG FS/HS, 100M Ethernet, SDIO, DCMI |
| Rentang Suhu Kerja | -40C to +85C |
| Tipe Mounting | Surface Mount |
| Status RoHS | Compliant |
| Lead-Free / Halogen-Free | Yes |
Konfigurasi Pin STM32F405RGT6
| Pin produk 1 | VBAT — Battery domain supply for RTC and backup SRAM |
| Pin produk 2 | PC13 — GPIO/Tamper-RTC (standard I/O with interrupt) |
| Pin produk 3 | PC14 — GPIO/OSC32_IN (32.768 kHz crystal) |
| Pin produk 4 | PC15 — GPIO/OSC32_OUT (32.768 kHz crystal) |
| Pin produk 5 | OSC_IN — HSE crystal/clock input |
| Pin produk 6 | OSC_OUT — HSE crystal output |
| Pin produk 7 | NRST — Reset input (active low) |
| Pin produk 8 | VSSA — Analog ground |
| Pin produk 9 | VDDA — Analog supply (1.8-3.6V) |
| Pin produk 10 | PA0-WKUP — GPIO/ADC0_IN0/Wakeup |
| Pin produk 11 | PA1 — GPIO/ADC0_IN1 |
| Pin produk 12 | PA2 — GPIO/USART2_TX/ADC0_IN2 |
| Pin produk 13 | PA3 — GPIO/USART2_RX/ADC0_IN3 |
| Pin produk 14 | PA4 — GPIO/SPI1_NSS/DAC_OUT1 |
| Pin produk 15 | PA5 — GPIO/SPI1_SCK/DAC_OUT2 |
| Pin produk 16 | PA6 — GPIO/SPI1_MISO/ADC1_IN2 |
| Pin produk 17 | PA7 — GPIO/SPI1_MOSI/ADC1_IN3 |
| Pin produk 18 | PB0 — GPIO/ADC2_IN8/TIM3_CH3 |
| Pin produk 19 | PB1 — GPIO/ADC2_IN9/TIM3_CH4 |
| Pin produk 20 | VSS_1 — Digital ground |
| Pin produk 21 | VDD_1 — Digital supply (1.8-3.6V) |
| Pin produk 22 | PB2/BOOT1 — GPIO/BOOT1 input |
| Pin produk 23 | PB10 — GPIO/I2C2_SCL/USART3_TX |
| Pin produk 24 | PB11 — GPIO/I2C2_SDA/USART3_RX |
| Pin produk 25 | VSS_2 — Digital ground |
| Pin produk 26 | VDD_2 — Digital supply (1.8-3.6V) |
| Pin produk 27 | PB12 — GPIO/SPI2_NSS/CAN2_RX |
| Pin produk 28 | PB13 — GPIO/SPI2_SCK/CAN2_TX |
| Pin produk 29 | PB14 — GPIO/SPI2_MISO/TIM12_CH1 |
| Pin produk 30 | PB15 — GPIO/SPI2_MOSI/TIM12_CH2 |
| Pin produk 31 | PA8 — GPIO/TIM1_CH1/USART1_CK/MCO |
| Pin produk 32 | PA9 — GPIO/USART1_TX/TIM1_CH2 |
| Pin produk 33 | PA10 — GPIO/USART1_RX/TIM1_CH3 |
| Pin produk 34 | PA11 — GPIO/USB_DM/CAN1_RX/TIM1_CH4 |
| Pin produk 35 | PA12 — GPIO/USB_DP/CAN1_TX/TIM1_ETR |
| Pin produk 36 | PA13 — GPIO/SWDIO |
| Pin produk 37 | VSS_3 — Digital ground |
| Pin produk 38 | VDD_3 — Digital supply (1.8-3.6V) |
| Pin produk 39 | PA14 — GPIO/SWCLK |
| Pin produk 40 | PA15 — GPIO/SPI3_NSS/TIM2_CH1 |
| Pin produk 41 | PC6 — GPIO/USART6_TX/TIM3_CH1 |
| Pin produk 42 | PC7 — GPIO/USART6_RX/TIM3_CH2 |
| Pin produk 43 | PC8 — GPIO/SDIO_D0/TIM3_CH3 |
| Pin produk 44 | PC9 — GPIO/SDIO_D1/TIM3_CH4 |
| Pin produk 45 | PA0 — GPIO/WKUP/USART2_CTS |
| Pin produk 46 | VDD_4 — Digital supply (1.8-3.6V) |
| Pin produk 47 | VSS_4 — Digital ground |
| Pin produk 48 | PB3 — GPIO/SPI3_SCK/TIM2_CH2 |
| Pin produk 49 | PB4 — GPIO/SPI3_MISO/TIM3_CH1 |
| Pin produk 50 | PB5 — GPIO/SPI3_MOSI/I2C1_SMBA |
| Pin produk 51 | PB6 — GPIO/I2C1_SCL/TIM4_CH1/USART1_TX |
| Pin produk 52 | PB7 — GPIO/I2C1_SDA/TIM4_CH2/USART1_RX |
| Pin produk 53 | BOOT0 — Boot mode select |
| Pin produk 54 | PB8 — GPIO/I2C1_SCL/CAN1_RX/TIM4_CH3 |
| Pin produk 55 | PB9 — GPIO/I2C1_SDA/CAN1_TX/TIM4_CH4 |
| Pin produk 56 | VSS_5 — Digital ground |
| Pin produk 57 | VDD_5 — Digital supply (1.8-3.6V) |
| Pin produk 58 | PD0 — GPIO/FSMC_D2/CAN1_RX |
| Pin produk 59 | PD1 — GPIO/FSMC_D3/CAN1_TX |
| Pin produk 60 | VREF+ — ADC positive reference |
| Pin produk 61 | VSSA — Analog ground |
| Pin produk 62 | VDDA — Analog supply |
| Pin produk 63 | PA13 — GPIO (secondary) |
| Pin produk 64 | VSS — Ground (additional) |
Aplikasi Umum
STM32F405RGT6 cocok untuk 7 aplikasis: Field-Oriented-Control Motor Drives, Industrial USB Host Peripherals, Digital Power Conversion and PFC, Audio Processing and DAC/ADC Interfaces, Industrial Ethernet Gateways, Consumer Medical Devices, Drones and Robotics Controllers.
Field-Oriented-Control Motor Drives
The STM32F405RGT6 fits FOC motor drives because the Cortex-M4F FPU and DSP instructions accelerate Park/Clarke transforms and PID loops by roughly 2-3x versus a Cortex-M3. The 168 MHz clock headroom leaves 30-40 percent CPU margin for encoder decoding and current-loop control. The 3x 12-bit ADCs sample phase currents at 2.4 MSPS, while the 12 timers provide complementary PWM with hardware dead-time insertion. Place a 100 nF decoupling cap on every VDD pin and route ADC inputs away from PWM switching nodes to preserve SNR.
Direkomendasikan
Industrial USB Host Peripherals
The STM32F405RGT6 is widely used in industrial USB host peripherals because the integrated USB OTG Full-Speed and High-Speed PHY eliminates an external ULPI chip, reducing BOM by approximately USD 1-2. The Cortex-M4F core handles USB stack processing and application logic simultaneously. The SDIO controller and FSMC bus (on the F407 family variant) support external data buffering for printers, scanners, and data loggers. Designers should route the 90-ohm USB differential pair with length matching within 150 mil and add ESD protection diodes.
Direkomendasikan
Digital Power Conversion and PFC
The STM32F405RGT6 is well-suited to digital power conversion and PFC stages because the Cortex-M4F single-precision FPU accelerates multiply-accumulate loops used in PID, state-space, and predictive control algorithms. The 12-bit ADCs sampled at 2.4 MSPS capture current and voltage waveforms with adequate bandwidth for PFC at 50-100 kHz switching. The high-resolution timer (217 ps) generates phase-shifted PWM for bridgeless PFC topologies. Plan 4-layer PCB layout to keep switching noise away from analog signal paths.
Direkomendasikan
Audio Processing and DAC/ADC Interfaces
The STM32F405RGT6 serves audio processing applications because the Cortex-M4F SIMD instructions accelerate FFT, biquad, and dynamics processing at 48 kHz sample rates. The 2x 12-bit DACs and 3x 12-bit ADCs integrate codec functionality for budget audio products. The I2S-capable SPI port supports external 24-bit codecs. The 192 KB SRAM buffers multiple audio frames without external memory. Use DMA for both I2S RX and TX to keep the core free for DSP processing.
Direkomendasikan
Industrial Ethernet Gateways
The STM32F405RGT6 fits industrial Ethernet gateways because the integrated 100 Mbit/s MAC and RMII interface connect to any standard Ethernet PHY for Modbus TCP, EtherNet/IP, or PROFINET. The Cortex-M4F core runs TCP/IP stacks plus application logic without external memory. The CAN 2.0B peripherals bridge fieldbus to enterprise networks. Pair with a wide-input DC-DC and provide 2 kV galvanic isolation on the Ethernet magnetics for industrial EMC compliance.
Direkomendasikan
Consumer Medical Devices
The STM32F405RGT6 powers consumer medical devices like blood-pressure monitors, pulse oximeters, and spirometers because the Cortex-M4F core runs sensor-fusion DSP while the 12-bit ADC captures analog biosignals with 2.4 MSPS. The 1 MB Flash accommodates FDA-21CFR-Part-11 firmware with bootloader and OTA update. The USB OTG port provides powered device charging and data sync. Use the RTC with battery domain to maintain accurate timestamps across power cycles.
Direkomendasikan
Drones and Robotics Controllers
The STM32F405RGT6 is a popular flight-controller MCU in hobbyist and commercial drones because the Cortex-M4F core runs Betaflight/Cleanflight/INAV firmware with full PID loops at 8 kHz update rates. The 168 MHz clock plus FPU computes quaternion math at rates that 72 MHz Cortex-M3 parts struggle to maintain. The 3x SPI ports connect to gyros, barometers, and radio receivers simultaneously. Mount the LQFP-64 with thermal vias to a copper pour for thermal relief at 50-60 mA active current.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk STM32F405RGT6 — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | STM32F415RGT6 | STM32F405RGT7 | STM32F405ZGT6 | GD32F405RGT6 |
|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | GigaDevice |
| Package | 64-LQFP (10x10 mm) | 64-LQFP (10x10 mm) - same | 64-LQFP (10x10 mm) - same | 144-LQFP (20x20 mm) | 64-LQFP (10x10 mm) - same |
| Core | Cortex-M4F @ 168 MHz | Cortex-M4F @ 168 MHz | Cortex-M4F @ 168 MHz | Cortex-M4F @ 168 MHz | Cortex-M4F @ 168 MHz |
| Flash | 1 MB | 1 MB | 1 MB | 1 MB | 1 MB |
| SRAM | 192 KB | 192 KB | 192 KB | 192 KB | 192 KB |
| Crypto/Hash Engine | No | Yes (AES, SHA) | No | No | No |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +105C | -40C to +85C | -40C to +85C |
| GPIO Count | 51 | 51 | 51 | 114 | 51 |
| Approx. Unit Price (1k qty) | USD 6.75 | USD 7.40 | USD 6.95 | USD 9.10 | USD 3.20 (GigaDevice, LCSC) |
Diferensiator Kunci
- Integrated USB OTG High-Speed PHY (vsSTM32F103RCT6 (Cortex-M3))
- Single-precision FPU with DSP instructions (vsSTM32F103C8T6 (Cortex-M3))
- 1 MB Flash versus typical 256-512 KB Cortex-M3 baseline (vsGD32F103RCT6)
Catatan Desain
Provide a 100 nF decoupling capacitor on every VDD/VSS pin pair, placed within 2 mm of the pin. Add a bulk 4.7 uF ceramic near the VDD-1/VSS-1 cluster and a 10 uF tantalum or ceramic at the regulator output. For USB OTG HS operation, the internal PHY requires VDD-USB supply stable within 90 percent of nominal before the PLL is enabled, otherwise enumeration will fail. Estimated: assuming 100 mA active current at 3.3V, total power is 330 mW - the LQFP-64 theta_JA of approximately 50 C/W yields a 16C rise above ambient, well within safe limits.
Route the USB OTG HS D+/D- pair as a 90-ohm differential pair with length matching within 150 mil and no stubs. Keep the crystal traces short (under 5 mm) and guard them with a ground pour. The Ethernet RMII signals should be length-matched within 50 mil to the external PHY. SDIO traces must be length-matched within 100 mil and routed on the inner layer with an uninterrupted reference plane. Use 4-layer stackup with continuous GND plane beneath the MCU for return-path integrity.
Do not enable the PLL above 168 MHz without confirming the Flash wait-state configuration - zero wait states is only valid up to 168 MHz. BOOT0 must be pulled low for normal Flash boot or floating if unused; leaving it high drops the MCU into System Memory bootloader. For ADC accuracy, ensure VDDA is decoupled with a 100 nF + 1 uF combination and that VREF+ is bypassed with a 100 nF cap to VSSA. The LQFP-64's central exposed pad (if present) must be soldered to a ground pad for thermal relief.
Place the HSE crystal within 5 mm of the OSC_IN/OSC_OUT pins with short, symmetrical traces. Route the SWD/SWCLK debug signals away from high-current switching nodes. Place boot-mode and reset pull-ups adjacent to the MCU. Provide a TEST pad on PA13/PA14 for factory programming. The NRST line needs a 100 nF cap plus 10 kohm pull-up to VDD and should be exposed on a header for in-system reset capability.
Informasi Konformitas
RoHS compliant per ST product page. Not AEC-Q100 qualified; for automotive designs use the STM32F405RGT6-V variant or a different family member.
