ADS7817P - 12-Bit 200 kSPS Differential ADC | Texas Instruments
部品番号: ADS7817P ✓ 生産中ADS7817P 概要
An ADC is a data-acquisition and data-conversion IC that converts an analog voltage into a digital code for processing, measurement, storage, or transmission. Within the broader semiconductor hierarchy, the ADS7817P is a sampling ADC, then a data-converter IC, and ultimately an interface or data-acquisition IC. Its differential architecture is especially useful when the measured signal is centered around a common reference voltage or when rejecting common-mode noise is important.
The principal features of the ADS7817P include 12-bit resolution, a 200 kSPS conversion rate, and differential analog input. The flexible 100 mV to 2.5 V reference range allows the same converter to serve both small-signal sensor measurements and higher-range industrial instrumentation. Automatic power-down helps reduce energy consumption when the converter is not continuously sampling, which is valuable in portable acquisition systems where duty cycling is common.
Each conversion produces a 12-bit result. The usable code resolution depends on the selected reference voltage and the analog input range. At a 100 mV reference, the converter can provide an input-referred resolution of 49 µV; at a 2.5 V reference, the corresponding resolution is 1.22 mV. These values make reference selection a central system-design decision because increasing the reference range can improve resolution while requiring more analog headroom and careful frontend scaling.
Typical applications include direct transducer interfacing, battery-operated measurement instruments, remote data-acquisition nodes, and multichannel analog monitoring systems. In each case, the ADC can sample a differential sensor output and produce digital data for a microcontroller, embedded processor, or communications interface. Differential input also helps the design reject noise that is common to both signal wires when the external analog circuitry is arranged appropriately.
Layout should prioritize a short, symmetrical route between the input source, reference circuit, and converter pins. Decoupling capacitors should be placed close to their associated supply and reference pins, while analog and digital return currents should be managed to prevent converter activity from coupling into the input signal. The 8-pin mini-DIP package supports straightforward through-hole prototyping and replacement without requiring a fine-pitch surface-mount assembly.
This product page combines the manufacturer specifications with package information, application guidance, verified alternatives, and engineering-oriented design notes. It is intended to help engineers evaluate resolution, conversion speed, reference range, input architecture, and board-level implementation before integrating the ADS7817P into a data-acquisition design.
ドロップイン代替品: ADS7817P — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
ADS7817IP
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
AD7817AR
✅ ドロップイン📋 参考代替品(カタログ未掲載)
AD7817BR
✅ ドロップイン📋 参考代替品(カタログ未掲載)
ADS7817P 最大定格&電気的特性
| Converter Type | 12-bit sampling analog-to-digital converter |
| サンプリングレート | 200 kSPS |
| 分解能 | 12 bit |
| Analog Input Architecture | Fully differential |
| Input Impedance | High impedance |
| Reference Voltage Range | 100 mV to 2.5 V |
| Input-Referred Resolution at 100 mV Reference | 49 µV |
| Input-Referred Resolution at 2.5 V Reference | 1.22 mV |
| Power-Down Function | Automatic power-down |
| Power Consumption | Low power |
| パッケージ | 8-pin plastic mini-DIP |
| 実装タイプ | Through-hole |
ADS7817P 8-pin plastic mini-dip ピン配置ガイド
ADS7817P (8-pin plastic mini-dip パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: ADS7817P.
詳細は データシート をご参照ください。
主な用途
ADS7817P の用途: 6 件s: Battery-Powered Sensor Measurement, Remote Data Acquisition, Industrial Transducer Interface, Multichannel Analog Monitoring, Precision Analog Measurement, Laboratory and Portable Instrumentation.
Battery-Powered Sensor Measurement
The ADS7817P fits battery-powered sensor nodes because it combines low-power operation with automatic power-down and a high-impedance differential input. Its 12-bit resolution and 200 kSPS sampling rate support rapid acquisition from differential sensor outputs while the converter remains inactive during longer idle intervals. A 100 mV reference can provide 49 µV input-referred resolution for small sensor signals, although the reference and signal-conditioning circuitry must remain low-power to preserve battery life. In a complete instrument, the converter can digitize the sensor output before the data is stored or transmitted by an embedded controller.
おすすめ
Remote Data Acquisition
The ADS7817P is suitable for remote data-acquisition modules that must capture differential analog measurements close to the sensor and transmit digital results over a communications link. Its 200 kSPS conversion rate provides useful throughput for monitoring rapidly changing signals, while the 8-pin mini-DIP package keeps through-hole construction straightforward. The fully differential input helps reject common-mode noise when the sensor, amplifier, and converter share a suitable reference. Designers should provide local reference and bypass capacitors and isolate the analog input routing from digital interface activity to preserve measurement quality.
おすすめ
Industrial Transducer Interface
The ADS7817P can serve as the sampling element in an industrial transducer interface because its high-impedance differential input supports direct connection to suitable signal-conditioning circuits. The 12-bit converter operates at up to 200 kSPS, allowing it to capture process or physical measurements with better temporal resolution than a slow meter-class ADC. Selecting a reference between 100 mV and 2.5 V determines the input-referred resolution from 49 µV to 1.22 mV. For industrial use, the frontend should include appropriate input protection, filtering, and settling time for the selected sensor and multiplexer configuration.
おすすめ
Multichannel Analog Monitoring
The ADS7817P is appropriate for multichannel monitoring systems in which several analog inputs are scanned through a multiplexer and converted sequentially. A 200 kSPS conversion rate leaves time for input selection and source settling, provided the external network is designed around the converter's acquisition requirements. Differential channels improve common-mode rejection when paired sensor outputs are balanced around the same reference. Engineers should minimize switch resistance, allow adequate settling at the ADC input, and maintain separate analog and digital return paths so that multiplexing transients do not dominate the selected input-referred resolution.
おすすめ
Precision Analog Measurement
The ADS7817P supports precision analog measurement where 12-bit resolution is sufficient but higher sampling speed is needed. With a 100 mV reference, its input-referred resolution is 49 µV; with a 2.5 V reference, it is 1.22 mV. This flexibility allows the reference range to be matched to the signal rather than fixing one input scale. The differential architecture is beneficial for bridge, current, and voltage measurements centered around the reference voltage. Frontend amplifier gain, input resistance, filtering, and reference stability should be evaluated together because they directly affect whether the converter's nominal resolution is retained in the completed system.
おすすめ
Laboratory and Portable Instrumentation
The ADS7817P is well suited to compact laboratory and portable instruments that need a low-power, differential ADC in an easy-to-handle 8-pin package. Its 200 kSPS sampling rate supports waveform capture and rapid measurement updates, while automatic power-down can reduce consumption between operating cycles. A 100 mV reference offers finer input-referred resolution for low-level transducers, whereas a 2.5 V reference supports a wider measurement range. The board should place input-conditioning components near the converter, use compact stable references, and account for connector leakage when working with very high source impedances.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: ADS7817P — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | ADS7817IP | AD7817AR | AD7817BR |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Analog Devices | Analog Devices |
| Package | 8-pin plastic mini-DIP | 8-pin plastic mini-DIP | 8-pin plastic mini-DIP | 8-pin plastic mini-DIP |
| Converter Type | Sampling ADC | Sampling ADC | Sampling ADC | Sampling ADC |
| Resolution | 12 bit | 12 bit | 12 bit | 12 bit |
| Sampling Rate | 200 kSPS | 200 kSPS | 200 kSPS | 200 kSPS |
| Input Architecture | Fully differential | Differential | Differential | Differential |
主な差別化要因
- Flexible reference range supports both low-level and wider-range measurements (vs AD7817AR)
- Automatic power-down supports duty-cycled acquisition (vs AD7817AR)
- Through-hole 8-pin construction simplifies prototype assembly (vs ADS7817IP)
設計ノート
Route the differential input as a short, symmetrical pair and place input-series resistors or filtering components close to the converter when they are part of the signal-conditioning network. Keep the analog input nodes away from digital output and serial-interface traces. Differential routing helps preserve common-mode rejection, but it only works effectively when both channels have comparable impedance, the source is correctly referenced, and the common-mode voltage remains within the converter's permitted input range.
Place the reference bypass capacitor and supply-decoupling capacitor directly beside their associated pins, with short ground returns. The reference voltage may be selected from 100 mV to 2.5 V, so reference noise and source impedance can materially affect the 49 µV to 1.22 mV input-referred resolution. Use a low-noise reference source and avoid long parallel copper paths that can couple converter or digital switching activity into the reference node.
Do not assume that a 200 kSPS conversion rate is the usable multichannel throughput without accounting for multiplexer settling and acquisition time. The external driver must present a settled voltage at the converter input during the sampling interval. Similarly, automatic power-down should be coordinated with control logic and measurement timing so that the converter has sufficient startup and acquisition time before the next valid conversion is read.
Treat the analog input and reference as precision signal paths rather than general-purpose routing. Guard against leakage from contaminated PCBs, connector cleaning issues, and high-impedance sensor nodes when operating near the 100 mV reference range. If a low reference is selected, verify input bias current, switch leakage, and resistor tolerance because these effects can become significant relative to the 49 µV input-referred resolution.
コンプライアンス情報
The manufacturer product page and distributor excerpts do not state the requested compliance or material-status classifications. Use the current Texas Instruments product documentation and declarations for qualification and environmental compliance decisions.