ADS8383IPFBTG4 - 18-Bit 500kHz SAR ADC, 48-TQFP | Texas Instruments
部品番号: ADS8383IPFBTG4 ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $18.75 | $18.75 |
| 10 | $16.92 | $169.20 |
| 100 | $14.1 | $1,410.00 |
| 250 | $12.65 | $3,162.50 |
| 500 | $11.4 | $5,700.00 |
ADS8383IPFBTG4 概要
A SAR ADC is a precision data converter architecture that uses a binary-search algorithm across an internal capacitor DAC to resolve each conversion in a fixed number of clock cycles. Compared with delta-sigma and pipeline ADCs, SAR converters offer deterministic latency and excellent linearity at moderate sample rates, making them the preferred choice for multiplexed data-acquisition systems, industrial process control, and instrumentation front-ends where repeatable per-sample timing matters more than the highest possible throughput.
Key specifications include 18-bit no-missing-codes resolution, 500 kSPS maximum throughput, an 18-/16-/8-bit selectable parallel interface, and a true bipolar-capable pseudo-bipolar input stage when driven with a VREF-centered input. The device features a high-impedance CMOS input structure with 4.5 ns aperture delay and excellent common-mode rejection, allowing direct connection to high-impedance sensors and instrumentation amplifiers. The internal sample-and-hold accepts fast-slewing transients, simplifying front-end design.
Typical applications include precision industrial process control, medical instrumentation, optical network power monitoring, vibration analysis, and high-accuracy multi-channel data-acquisition systems. The wide input range and parallel interface are well suited to FPGAs and DSPs in motor control and power-quality monitoring.
When designing with this part, place a low-ESR 1 uF ceramic bypass capacitor directly on the +VA and +VBD pins, plus a 10 uF bulk capacitor, to suppress supply-induced conversion noise. Use a low-impedance ground plane and keep analog and digital return currents separated to within 1 inch of the device.
This page synthesizes distributor pricing, drop-in alternatives, application notes, and PCB design guidance not found in a single source on DigiKey, Mouser, or the TI product folder.
ドロップイン代替品: ADS8383IPFBTG4 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: ADS8383IPFBTG4 （同一形状・フットプリント） — 相違点: Package, Input Type, Resolution, Architecture, Sample Rate.
クイック比較ツール — 並列比較する代替部品を選択:
ADS8383IPFBRG4
✅ ドロップイン✓ 在庫あり
$11.95 / 個
データシートを見る →ADS8383IPFBT
✅ ドロップイン📋 参考代替品（カタログ未掲載）
ADS8381IBPFBR
✅ ドロップイン✓ 在庫あり
$9.85 / 個
データシートを見る →ADS8382IRHPR
✅ ドロップイン✓ 在庫あり
$9.65 / 個
データシートを見る →ADS8342IBPFBR
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$9.45 / 個
データシートを見る →ADS8343EB/2K5G4
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$7.4 / 個
データシートを見る →ADS8383IPFBTG4 最大定格＆電気的特性
| 分解能 | 18 bits |
| Sample Rate | 500 kSPS |
| Architecture | SAR (Successive Approximation) |
| Input Channels | 1 (single-ended, unipolar) |
| Analog Supply Voltage (+VA) | 5 V |
| Digital Supply Voltage (+VBD) | 5 V (3.3 V logic compatible) |
| Analog Input Range | 0 V to +VREF (default); 0 V to 2 x VREF with PGA gain = 2 |
| Reference Voltage (VREF) | 4.0 V typ, 4.5 V max |
| Conversion Time | 1.52 us typ |
| インターフェース | Parallel, 18-/16-/8-bit selectable |
| INL (max) | 2.5 LSB |
| DNL (max) | 1.5 LSB (-0.99 to +2.5 LSB) |
| SNR | 84 dB typ at 100 kHz input |
| Power Dissipation (500 kSPS) | 110 mW typ |
| Power Dissipation (10 kSPS) | 8 mW typ |
| Aperture Delay | 4.5 ns |
| 動作温度 | -40C to +85C (Industrial) |
| パッケージ | 48-pin TQFP (PFB), 7 mm x 7 mm |
| RoHS ステータス | Compliant |
| Lead-Free | Yes |
ADS8383IPFBTG4 ピン構成
| ピン 1 | DVDD — Digital supply (3.3V or 5V) |
| ピン 2 | DGND — Digital ground |
| ピン 3 | DB0 — Data bit 0 (LSB) |
| ピン 4 | DB1 — Data bit 1 |
| ピン 5 | DB2 — Data bit 2 |
| ピン 6 | DB3 — Data bit 3 |
| ピン 7 | DB4 — Data bit 4 |
| ピン 8 | DB5 — Data bit 5 |
| ピン 9 | DB6 — Data bit 6 |
| ピン 10 | DB7 — Data bit 7 |
| ピン 11 | DB8 — Data bit 8 |
| ピン 12 | DB9 — Data bit 9 |
| ピン 13 | DB10 — Data bit 10 |
| ピン 14 | DB11 — Data bit 11 |
| ピン 15 | DB12 — Data bit 12 |
| ピン 16 | DB13 — Data bit 13 |
| ピン 17 | DB14 — Data bit 14 |
| ピン 18 | DB15 — Data bit 15 |
| ピン 19 | DB16 — Data bit 16 |
| ピン 20 | DB17 — Data bit 17 (MSB) |
| ピン 21 | BYTE — 8/16/18-bit mode select |
| ピン 22 | SEQ — Sequential mode select |
| ピン 23 | /BUSY — Conversion-in-progress (active low) |
| ピン 24 | /CS — Chip select (active low) |
| ピン 25 | /RD — Read strobe (active low) |
| ピン 26 | /CONVST — Conversion start (active low) |
| ピン 27 | RESET — Reset input |
| ピン 28 | TAG — Tag input for data tagging |
| ピン 29 | DGND — Digital ground |
| ピン 30 | DVDD — Digital supply |
| ピン 31 | NC — Not connected |
| ピン 32 | NC — Not connected |
| ピン 33 | VREF — Reference voltage input |
| ピン 34 | REFGND — Reference ground |
| ピン 35 | REFM — Reference minus / REFGND |
| ピン 36 | AGND — Analog ground |
| ピン 37 | AVDD — Analog supply (+5V) |
| ピン 38 | AINP — Analog input positive |
| ピン 39 | AINM — Analog input negative / AGND |
| ピン 40 | AGND — Analog ground |
| ピン 41 | AVDD — Analog supply (+5V) |
| ピン 42 | NC — Not connected |
| ピン 43 | NC — Not connected |
| ピン 44 | AGND — Analog ground |
| ピン 45 | AVDD — Analog supply (+5V) |
| ピン 46 | NC — Not connected |
| ピン 47 | NC — Not connected |
| ピン 48 | AVDD — Analog supply (+5V) |
主な用途
ADS8383IPFBTG4 の用途: 6 件s: Industrial Process Control / PLC, Medical Instrumentation & Patient Monitoring, Optical Network Power Monitoring, Vibration Analysis & Condition Monitoring, Power Quality & Energy Metering, Precision Data-Acquisition Systems (DAQ).
Industrial Process Control / PLC
The ADS8383IPFBTG4's 18-bit no-missing-codes resolution, -40C to +85C industrial temperature range, and 500 kSPS throughput make it a strong fit for PLC analog input modules in industrial process control. Its 0 V to +VREF unipolar input accepts 4-20 mA loop outputs via a 250 ohm current-sense resistor, while 84 dB SNR at 100 kHz input supports high-accuracy measurement of pressure, temperature, and flow transducers. The 48-TQFP package reflow-mounts reliably on standard FR-4, and the parallel interface connects directly to industrial FPGAs in PLC backplanes.
おすすめ
Medical Instrumentation & Patient Monitoring
In medical instrumentation such as infusion pumps, blood analyzers, and patient monitors, the ADS8383IPFBTG4 delivers 18-bit resolution at 500 kSPS to digitize low-frequency biosignals with high dynamic range. The integrated sample-and-hold and 4.5 ns aperture delay preserve phase accuracy on ECG and EEG front-ends, while the parallel interface streams data to a DSP for real-time DSP filtering. Its 110 mW power dissipation at full throughput is acceptable for line-powered equipment, and the industrial temperature range supports continuous operation in clinical environments.
おすすめ
Optical Network Power Monitoring
Optical line cards and transponder modules use the ADS8383IPFBTG4 to digitize the output of photodiode transimpedance amplifiers monitoring transmit laser power. The 500 kSPS sample rate and 18-bit resolution enable tight closed-loop control of laser bias and modulation currents, stabilizing optical output power across temperature. The device's 84 dB SNR rejects ambient optical noise, and the parallel interface feeds FPGA-based control loops that adjust laser driver DACs in microseconds. Industrial temperature range suits outdoor OLT chassis.
おすすめ
Vibration Analysis & Condition Monitoring
Predictive maintenance systems in motors, pumps, and rotating machinery use the ADS8383IPFBTG4 to digitize accelerometer signals for FFT-based vibration analysis. The 500 kSPS sample rate captures vibration harmonics up to 200 kHz (Nyquist), while 18-bit resolution distinguishes early-stage bearing faults by 0.001 g spectral peaks. The deterministic 1.52 us SAR latency simplifies phase-coherent analysis across multiple channels when combined with the ADS8382IRHPR for 4-axis simultaneous sampling on the same PCB footprint.
おすすめ
Power Quality & Energy Metering
Three-phase power-quality analyzers and revenue-grade energy meters use the ADS8383IPFBTG4 to digitize voltage and current waveforms with 18-bit accuracy at 500 kSPS. The high dynamic range supports harmonic analysis to the 50th harmonic at 50/60 Hz mains frequency, and the wide input range accommodates current-transformer (CT) and voltage-divider (VT) front-ends. Industrial temperature rating and SAR determinism make it a reliable core for IEC 62053-22 class 0.2S meters deployed in substations and industrial switchgear.
おすすめ
Precision Data-Acquisition Systems (DAQ)
Multi-channel DAQ boards for test and measurement applications use the ADS8383IPFBTG4 for the highest-resolution single-channel inputs alongside the ADS8382IRHPR for multiplexed channels. The 18-bit/500 kSPS performance and 48-TQFP package allow up to 8 channels per 4-layer PCB while maintaining 84 dB SNR, supporting LXI-class modular instruments. The parallel interface streams samples directly into FPGA acquisition buffers, enabling sustained 500 kSPS per channel with deterministic timing for waveform capture and protocol analysis.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: ADS8383IPFBTG4 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | ADS8383IPFBRG4 | ADS8383IPFBT | ADS8381IBPFBR | ADS8382IRHPR | ADS8342IBPFBR | ADS8343EB/2K5G4 |
|---|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 48-TQFP (PFB) 7x7 mm | 48-TQFP (PFB) 7x7 mm | 48-TQFP (PFB) 7x7 mm | 48-TQFP (PFB) 7x7 mm | 48-QFN (RHP) | 48-TQFP (PFB) 7x7 mm | 48-TQFP (PFB) 7x7 mm |
| Resolution | 18 bits | 18 bits | 18 bits | 18 bits | 16 bits | 16 bits | 12 bits |
| Sample Rate | 500 kSPS | 500 kSPS | 500 kSPS | 500 kSPS | 500 kSPS | 250 kSPS | 100 kSPS |
| Input Channels | 1 (single-ended) | 1 (single-ended) | 1 (single-ended) | 1 (single-ended) | 4 (single-ended) | 4 (single-ended) | 4 (single-ended) |
| Architecture | SAR | SAR | SAR | SAR | SAR | SAR | SAR |
| Interface | Parallel (18/16/8-bit) | Parallel (18/16/8-bit) | Parallel (18/16/8-bit) | Parallel (18/16/8-bit) | Serial | Serial | Serial |
| Analog Supply | 5V | 5V | 5V | 5V | 5V | 5V | 2.7V |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
| 1-piece Price (USD, approx) | 18.75 | 18.75 | 18.75 | 16.50 | 14.20 | 9.85 | 5.40 |
主な差別化要因
- Industry-leading 18-bit single-channel resolution at 500 kSPS （vs ADS8382IRHPR)
- Parallel interface eliminates SPI bit-banging overhead （vs ADS8342IBPFBR / ADS8343EB/2K5G4)
- Genuine industrial temperature grade with single 5V supply （vs ADS8343EB/2K5G4)
設計ノート
Place a 0.1 uF X7R ceramic decoupling capacitor within 2 mm of each AVDD pin (37, 41, 45, 48) and each DVDD pin (1, 30) to suppress high-frequency noise during conversion. Add a 10 uF tantalum or ceramic bulk capacitor on the analog supply rail near the device. The +VA and +VBD supplies should be powered from a low-noise LDO (e.g., TPS7A4701) and decoupled separately; tying AVDD to a noisy 5V switching node will inject 1-2 LSB of conversion noise. Reference: TI ADS8383 datasheet, Section 'Power Supply'.
Use a continuous ground plane under the device and partition it into separate analog (AGND/REFGND) and digital (DGND) islands connected at a single point directly under the device. Route analog input traces (AINP/AINM) as a differential pair to a nearby op-amp (e.g., OPA2277) buffer, and route data bus traces DB0-DB17 matched-length to avoid skew on the 18-bit parallel output. Keep noisy digital lines (RD, CS, CONVST) at least 5 mm away from the analog input and VREF pins.
Drive the AINP input through a low-impedance op-amp buffer (e.g., OPA2277 or AD8628) to prevent source-impedance-induced INL degradation; the ADS8383 samples the input on the falling edge of CONVST, so the buffer must settle to within 0.5 LSB (10 uV at 5V VREF) before acquisition ends. For VREF, use a 4.5V low-noise reference such as REF5045 with a 0.1 uF and 10 uF bypass network; noise on VREF directly couples into SNR and linearity.
Do not leave unused data bus pins (DB16/DB17 for 16-bit mode) floating - tie them to DGND through 10 kohm resistors to avoid CMOS input oscillation. Do not apply a negative voltage to AINP when AGND is at 0V - the input protection diodes will forward-bias and degrade linearity. The /CONVST pin should be a clean falling edge; mechanical switch bounce or slow edges will cause aperture jitter exceeding the 50 ps spec. Always issue a hardware RESET after power-up before the first conversion.
コンプライアンス情報
RoHS compliant per TI product page. Industrial -40C to +85C temperature grade (I-suffix). Not AEC-Q100 qualified; for automotive, consider the ADS8383-Q1 variant if available in portfolio. Lead-free reflow-compatible 48-TQFP package.
