EPM240ZM100C7N - MAX II Z CPLD 192MC 7.5ns 100-MBGA | Altera/Intel
部品番号: EPM240ZM100C7N ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $9.2278 | $9.23 |
| 10 | $8.3 | $83.00 |
| 100 | $7.4 | $740.00 |
| 500 | $6.7 | $3,350.00 |
| 1,000 | $6.1 | $6,100.00 |
EPM240ZM100C7N 概要
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that provides instant-on operation, deterministic timing, and flexible glue-logic integration between microcontrollers, ASICs, and standard bus interfaces. CPLDs sit below FPGAs in the programmable logic hierarchy: they typically offer lower density but faster, fully deterministic propagation delays, making them ideal for address decoding, bus interfacing, power-up sequencing, and peripheral control rather than high-throughput data-path or DSP workloads. The MAX II family is the lowest-power instant-on CPLD family in the Altera/Intel portfolio.
Key features include 8 Kbits of on-chip user flash memory (UFM) for storing constants, serial numbers, or calibration data; a JTAG (IEEE 1149.1) interface for in-system programming and boundary-scan test; support for I/O standards including LVCMOS, LVTTL, PCI, and differential LVDS; and a typical standby current under 2 mA at 1.8 V core. The Z sub-family variant is engineered specifically for ultra-low static power dissipation, making it well suited to battery-powered and energy-harvesting designs where the device must idle for long intervals without draining the source.
Architecturally, the EPM240ZM100C7N is built around the Logic Array Block (LAB) interconnect fabric, with each LAB containing 10 logic elements and each LE implementing a 4-input look-up table, a programmable register, and a carry chain. The MultiVolt I/O architecture lets each bank be powered independently from the core, allowing direct interfacing to legacy 5 V-tolerant buses through external series resistors or level shifters. The device retains all configuration in on-chip flash, so power-up time is governed only by the I/O ramp-up sequence rather than by a PROM load cycle.
Typical applications include I/O expansion and address decoding for microcontrollers and microprocessors, power-up sequencing in multi-rail systems, glue logic in industrial control and factory automation boards, low-power portable and battery-backed instrumentation, LED display multiplexing, and consumer-electronics control boards. The 100-ball MBGA package has a footprint of approximately 6 x 6 mm, making it one of the smallest footprints available in the MAX II family.
When designing with the EPM240ZM100C7N, plan the MultiVolt bank assignments carefully because each I/O bank shares a VCCIO rail and mixing 1.5 V and 3.3 V signals requires at least two banks. Use Quartus II Web Edition (or the latest supported Intel Quartus Prime release) for design entry, fitting, and in-system programming via the JTAG port.
This page synthesizes the manufacturer datasheet, distributor pricing as of 2026-09-12, drop-in same-package alternatives from the MAX II family, and practical design notes that go beyond the datasheet's typical application section.
ドロップイン代替品: EPM240ZM100C7N — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: EPM240ZM100C7N （同一形状・フットプリント） — 相違点: Package, Configuration Memory, Process Technology, Operating Temperature, Family.
クイック比較ツール — 並列比較する代替部品を選択:
EPM240ZM100C6N
✅ ドロップイン✓ 在庫あり
$7.1 / 個
データシートを見る →EPM240ZM100C8N
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
EPM240GM100C5N
✅ ドロップイン✓ 在庫あり
$4.75 / 個
データシートを見る →EPM240F100C5N
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$5.2 / 個
データシートを見る →EPM570ZM100C7N
✅ ドロップイン✓ 在庫あり
$12.55 / 個
データシートを見る →EPM240ZM100C7N 最大定格＆電気的特性
| Family | MAX II Z |
| Series | MAX II |
| Logic Elements | 240 |
| Macrocells | 192 |
| Pin-to-Pin Logic Delay (tPD) | 7.5 ns |
| User I/Os | 80 |
| User Flash Memory (UFM) | 8 Kbits |
| Core Supply Voltage (VCCINT) | 1.8 V |
| I/O Supply Voltage (VCCIO) | 1.5 V / 1.8 V / 2.5 V / 3.3 V (MultiVolt) |
| パッケージ | 100-MBGA (Micro FineLine BGA), 6 x 6 mm |
| Configuration Memory | On-chip non-volatile flash |
| Process Technology | 0.18 µm 6-layer-metal flash |
| JTAG Support | IEEE 1149.1 (programming + boundary-scan) |
| 動作温度 | 0 °C to +85 °C (commercial) |
| 実装タイプ | Surface Mount (BGA) |
| Lead-Free / RoHS | Compliant per datasheet |
EPM240ZM100C7N 100-mbga (micro fineline bga), 6 x 6 mm ピン配置ガイド
EPM240ZM100C7N (100-mbga (micro fineline bga), 6 x 6 mm パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: EPM240ZM100C7N.
詳細は データシート をご参照ください。
主な用途
EPM240ZM100C7N の用途: 6 件s: Microprocessor Address Decoding and Bus Interfacing, Power-Up and Power-Down Sequencing, Industrial Glue Logic and Factory Automation, Low-Power Portable and Battery-Backed Devices, LED Display Multiplexing and Refresh Control, I/O Expansion and Peripheral Bridging.
Microprocessor Address Decoding and Bus Interfacing
The EPM240ZM100C7N's 7.5 ns pin-to-pin delay and 80 user I/Os make it well suited to decode external memory and peripheral address lines in 8/16/32-bit microcontroller or microprocessor systems. With 240 logic elements the device comfortably holds wide-chip-select decoders for SRAM, Flash, and peripheral banks while keeping propagation delay below one clock cycle at 50 MHz. The on-chip flash configuration ensures instant-on decoding without boot-PROM overhead. Place the CPLD close to the MCU address bus to minimize trace-induced skew and use MultiVolt I/O banks (1.8 V/2.5 V/3.3 V) to interface directly with the MCU without external level shifters. Pair with EPM1270T144C5N when more LE headroom is needed.
おすすめ
Power-Up and Power-Down Sequencing
The EPM240ZM100C7N is widely used to sequence multiple voltage rails in FPGA, SoC, and ASIC-based boards where specific turn-on/off orders are mandatory. Its instant-on non-volatile flash means the sequencing logic is active the moment VCCINT ramps, eliminating the boot-race condition seen with MCU-based sequencers. Each of the 80 I/Os can directly drive a MOSFET gate or enable pin through MultiVolt bank voltage selection, supporting 1.8 V, 2.5 V, and 3.3 V loads from a single device. Sequencing delays are set in hardware look-up tables, making them deterministic and immune to firmware bugs. Combine with EPM2210F256C5N for systems with more than 8 sequenced rails.
おすすめ
Industrial Glue Logic and Factory Automation
Factory automation boards require deterministic parallel logic to bridge sensor buses, motor-control ICs, and PLC backplanes, where the EPM240ZM100C7N's 7.5 ns tPD and 80 I/Os are well matched. The instant-on non-volatile flash survives brown-outs and noisy industrial supplies without re-programming, and the commercial 0 °C to +85 °C operating range covers most factory-floor environments. The MultiVolt I/O architecture lets a single CPLD connect to 24 V tolerant inputs through external resistor dividers and drive 3.3 V logic outputs in the same design. Pair with EPM570T100C5N when board area allows a TQFP and a higher logic budget is needed.
おすすめ
Low-Power Portable and Battery-Backed Devices
The MAX II Z sub-family is engineered for ultra-low static power consumption, making the EPM240ZM100C7N ideal for battery-backed and energy-harvesting products that must idle for long periods. Typical standby current below 2 mA at 1.8 V core allows the CPLD to monitor a wake-up signal without draining the source, while instant-on flash configuration eliminates the multi-millisecond boot delay of MCU-based supervisors. The 8 Kbit UFM block stores calibration constants and serial numbers, replacing an external EEPROM in many designs. Combine with EPM1270F256I5N when a larger UFM and more I/Os are required for handheld instrumentation.
おすすめ
LED Display Multiplexing and Refresh Control
The EPM240ZM100C7N's combination of 80 I/Os and 7.5 ns timing is well suited to driving multiplexed seven-segment, dot-matrix, and RGB-LED panels without any firmware overhead. Each row/column driver can be assigned to a dedicated MultiVolt I/O bank so 3.3 V and 5 V LED segments can be driven directly. The deterministic timing prevents the row-flicker artifacts that occur when MCU interrupts jitter the refresh rate, and the on-chip UFM can store lookup-table font data. Pair with EPM570ZM100C7N for larger RGB panels that exceed 240-LE capacity.
おすすめ
I/O Expansion and Peripheral Bridging
When an MCU or SoC runs out of GPIO pins, the EPM240ZM100C7N can serve as a low-latency I/O expander that translates SPI, I2C, or parallel commands into wider parallel bus actions. The CPLD's 240 logic elements hold small state machines and shift registers while the 80 I/Os fan out into multiple peripheral enables, chip selects, and status LEDs. The instant-on behavior means expanded peripherals are available immediately at power-up, before the host MCU finishes its own boot. Combine with EPM1270T144C5N when 80 I/Os is insufficient for the target peripheral count.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: EPM240ZM100C7N — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | EPM240ZM100C6N | EPM240ZM100C8N | EPM240GM100C5N | EPM240F100C5N | EPM570ZM100C7N |
|---|---|---|---|---|---|---|
| Package | 100-MBGA (6 x 6 mm) | 100-MBGA - same | 100-MBGA - same | 100-MBGA - same | 100-MBGA - same | 100-MBGA - same |
| Brand | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) |
| Family / Sub-family | MAX II Z (zero-power) | MAX II Z | MAX II Z | MAX II G | MAX II G | MAX II Z |
| Logic Elements | 240 | 240 | 240 | 240 | 240 | 570 |
| Macrocells | 192 | 192 | 192 | 192 | 192 | 440 |
| Pin-to-Pin Delay (tPD) | 7.5 ns | 8.5 ns | 7.5 ns | 5.0 ns | 5.0 ns | 7.5 ns |
| Core Voltage (VCCINT) | 1.8 V | 1.8 V | 1.8 V | 3.3 V | 3.3 V | 1.8 V |
| User I/Os | 80 | 80 | 80 | 80 | 80 | 76 |
| User Flash Memory (UFM) | 8 Kbits | 8 Kbits | 8 Kbits | 8 Kbits | 8 Kbits | 8 Kbits |
| Static Power Profile | Ultra-low (MAX II Z) | Ultra-low | Ultra-low | Standard | Standard | Ultra-low |
主な差別化要因
- Lowest-power MAX II sub-family for battery designs （vs EPM240GM100C5N)
- 7.5 ns speed grade balance of timing and cost （vs EPM240ZM100C6N)
- Pin-compatible density scaling within MAX II family （vs EPM570ZM100C7N)
設計ノート
The MAX II Z sub-family is optimized for ultra-low static power at 1.8 V VCCINT; ensure the regulator supplying VCCINT is rated for at most 50 mV dropout so the device remains in its low-power regime during battery operation. Decouple VCCINT with a 1 µF X7R ceramic within 5 mm of the BGA and add a 0.1 µF parallel cap for high-frequency noise. VCCIO banks should each have their own 0.1 µF + 1 µF decoupling pair, because bank-to-bank voltage differences (e.g. 1.8 V + 3.3 V) cannot share a single decoupling capacitor without leakage.
The 100-MBGA Micro FineLine BGA has 0.5 mm pitch and 6 x 6 mm body. Use a 4-layer PCB with continuous ground plane directly under the BGA to provide low-impedance return paths for the 80 I/Os. Vias-in-pad (VIP) with filled-and-capped plating are recommended to maximize escape routing density on inner layers. Keep all high-speed outputs (clocks, fast memory interfaces) on the outer layer for short stubs, and route MultiVolt bank VCCIO rails as wide traces or small power pours to avoid IR drop on heavily loaded banks.
Do not mix 3.3 V and 1.5 V signals within the same VCCIO bank - each I/O bank shares a single VCCIO rail, so voltage mixing forces a redesign into two banks. The JTAG TCK pin has no internal pull-up; if boundary-scan is unused, leave the JTAG chain intact or add a 10 kΩ pull-up on TCK to prevent spurious configuration attempts. Do not apply VCCIO before VCCINT, because I/O cells powered before the core can latch incorrect states. Finally, when migrating designs from EPM240T100 (TQFP) to EPM240ZM100 (MBGA), verify the pinout translation table in the MAX II handbook - the TQFP and MBGA pin numbers do NOT align 1:1 even though both are 100-pin.
Program the device with the JTAG chain in a known order if multiple MAX II devices are cascaded; the Quartus II/Prime programmer auto-detects the chain when BSDL files are loaded. Use a USB-Blaster or ByteBlaster-II cable rather than legacy ByteBlaster MV for reliable 1.8 V programming. Place the JTAG header within 50 mm of the device to avoid signal-integrity issues on TCK/TMS/TDO/TDI.
コンプライアンス情報
RoHS and lead-free per Altera/Intel MAX II Device Handbook and current distributor listings. MAX II Z is NOT AEC-Q100 qualified; for automotive designs use MAX 10 family instead.
