ISL81485IU - 30Mbps RS-485/RS-422 Transceiver | Renesas
部品番号: ISL81485IU ✗ 生産終了ISL81485IU 概要
An RS-485/RS-422 transceiver is an interface IC that converts single-ended digital signals into balanced differential signals for transmission and converts received differential signals back into a logic-level output. RS-422 is commonly associated with point-to-point, balanced communication, while RS-485 supports multipoint bus networks and driver inhibit capability. The ISL81485IU belongs to the broader hierarchy of interface transceivers, serial communication ICs, and semiconductors used to connect digital equipment over copper cabling.
The principal features of the ISL81485IU are its 5 V operation, 30 Mbps maximum signaling rate, and support for both RS-485 and RS-422 communication standards. Its single-transceiver format allows a compact design to implement a bidirectional link by connecting the driver and receiver controls to the same digital interface. The manufacturer datasheet describes a larger output voltage and higher data rate as beneficial for high-speed applications, while its BiCMOS process supports the demanding output and receiver requirements of balanced differential links.
In an RS-485 network, the differential bus reduces sensitivity to common-mode noise and allows data to be transmitted over longer cable runs than a conventional single-ended interface. The 30 Mbps capability makes the device relevant to factory automation, industrial control, data acquisition, and embedded instrumentation systems that need a compact point-to-point or multidrop communications interface. When two transceivers are used on a shared bus, driver-enable and receiver-enable controls determine which node drives or listens at any given time.
The principal design tradeoff is that a high-speed differential transceiver requires careful attention to board layout, termination, decoupling, grounding, and protection. The 5 V supply should be filtered near the device, and routed differential traces should remain closely coupled. Cabling and connector geometry also influence signal integrity, particularly at the maximum 30 Mbps operating rate.
This page combines the manufacturer specifications, interface-function analysis, sourcing fields, and practical RS-485/RS-422 design guidance to support component selection and PCB implementation. It also distinguishes confirmed drop-in candidates from related devices that require additional pin, timing, and protocol verification before substitution.
ドロップイン代替品: ISL81485IU — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: ISL81485IU (同一形状・フットプリント) — 相違点: Maximum Data Rate, Package, Product Type.
ISL81486IU
✅ ドロップイン価格はお問い合わせください
データシートを見る →ISL81485IU 仕様
| Product Type | Single RS-485/RS-422 line transceiver |
| 電源電圧 | 5 V |
| Maximum Data Rate | 30 Mbps |
| Supported Standards | RS-485 and RS-422 |
| Process Technology | BiCMOS |
| Number of Transceivers | 1 |
| パッケージ | 8-pin MSOP, 0.118 in (3.00 mm) width |
| 実装タイプ | Surface mount |
| Signal Interface | Balanced differential |
ISL81485IU 8-pin msop, 0.118 in (3.00 mm) width ピン配置ガイド
ISL81485IU (8-pin msop, 0.118 in (3.00 mm) width パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: ISL81485IU.
詳細は データシート をご参照ください。
主な用途
ISL81485IU の用途: 3 件s: 組込みシステム, IoTデバイス, 産業制御.
組込みシステム
ISL81485IUを使用した組込みアプリケーションのコア処理。
IoTデバイス
ISL81485IUを搭載したスマートコネクテッドデバイス。
産業制御
ISL81485IUを使用した自動化および制御システム。
エンジニアリング参考データ: ISL81485IU — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | ISL81486IU |
|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics |
| Package | 8-MSOP | 8-MSOP |
| Maximum Data Rate | 30 Mbps | 30 Mbps |
| Lifecycle Status | Obsolete | Obsolete |
| Mounting Type | Surface mount | Surface mount |
主な差別化要因
- High-speed balanced communications in a compact package (vs ISL81486IU)
- One device supports two balanced bus standards (vs ISL81486IU)
- Single-transceiver implementation reduces board area (vs ISL81486IU)
設計ノート
Route the differential pair as a closely coupled pair with continuous reference-plane geometry and minimize stubs, vias, and branch points. At 30 Mbps, discontinuities and unbalanced loading can degrade the differential signal. Keep the transceiver close to the connector and place termination components near the bus interface so that reflections are controlled without creating long high-frequency current loops.
Decouple the 5 V transceiver supply close to the device and keep the return-current path continuous beneath the IC and connector. Use the manufacturer-recommended capacitance and voltage rating, and account for supply ripple when the bus reaches its maximum 30 Mbps data rate. Avoid sharing a narrow supply path with unrelated switching or motor-current loads.
Do not substitute the ISL81485IU-T as a different functional alternative; it represents a distinct ordering or packing suffix for the same ISL81485 device. Before fitting an alternative transceiver, compare pin names, enable polarity, receiver-enable behavior, propagation delay, bus impedance, common-mode range, and power-off state. A shared MSOP outline alone does not guarantee behavioral compatibility.
For RS-485 networks, use an appropriate topology and termination strategy rather than adding termination indiscriminately to every node. Stubs should be minimized, especially on high-speed networks. The differential interface can improve noise immunity, but common-mode transients still require appropriate protection and grounding, particularly where the transceiver is connected to long external cables.
コンプライアンス情報
No definitive RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified in the available records. The ISL81485IU and ISL81486IU are identified as obsolete.