ISL81485IU - 30Mbps RS-485/RS-422 Transceiver | Renesas
MPN: ISL81485IU ✗ Cuối đờiISL81485IU Tóm tắt
An RS-485/RS-422 transceiver is an interface IC that converts single-ended digital signals into balanced differential signals for transmission and converts received differential signals back into a logic-level output. RS-422 is commonly associated with point-to-point, balanced communication, while RS-485 supports multipoint bus networks and driver inhibit capability. The ISL81485IU belongs to the broader hierarchy of interface transceivers, serial communication ICs, and semiconductors used to connect digital equipment over copper cabling.
The principal features of the ISL81485IU are its 5 V operation, 30 Mbps maximum signaling rate, and support for both RS-485 and RS-422 communication standards. Its single-transceiver format allows a compact design to implement a bidirectional link by connecting the driver and receiver controls to the same digital interface. The manufacturer datasheet describes a larger output voltage and higher data rate as beneficial for high-speed applications, while its BiCMOS process supports the demanding output and receiver requirements of balanced differential links.
In an RS-485 network, the differential bus reduces sensitivity to common-mode noise and allows data to be transmitted over longer cable runs than a conventional single-ended interface. The 30 Mbps capability makes the device relevant to factory automation, industrial control, data acquisition, and embedded instrumentation systems that need a compact point-to-point or multidrop communications interface. When two transceivers are used on a shared bus, driver-enable and receiver-enable controls determine which node drives or listens at any given time.
The principal design tradeoff is that a high-speed differential transceiver requires careful attention to board layout, termination, decoupling, grounding, and protection. The 5 V supply should be filtered near the device, and routed differential traces should remain closely coupled. Cabling and connector geometry also influence signal integrity, particularly at the maximum 30 Mbps operating rate.
This page combines the manufacturer specifications, interface-function analysis, sourcing fields, and practical RS-485/RS-422 design guidance to support component selection and PCB implementation. It also distinguishes confirmed drop-in candidates from related devices that require additional pin, timing, and protocol verification before substitution.
Bộ thay thế dễ dàng lắp đặt cho ISL81485IU — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ISL81485IU (cùng hình factor và footprint) — khác nhau ở Maximum Data Rate, Package, Product Type.
ISL81486IU
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ISL81485IU Thông số kỹ thuật
| Product Type | Single RS-485/RS-422 line transceiver |
| Điện áp cung cấp | 5 V |
| Maximum Data Rate | 30 Mbps |
| Supported Standards | RS-485 and RS-422 |
| Process Technology | BiCMOS |
| Number of Transceivers | 1 |
| Hộp | 8-pin MSOP, 0.118 in (3.00 mm) width |
| Kiểu lắp đặt | Surface mount |
| Signal Interface | Balanced differential |
Hướng dẫn cấu hình chân ISL81485IU 8-pin msop, 0.118 in (3.00 mm) width
Cấu hình chân cho ISL81485IU (8-pin msop, 0.118 in (3.00 mm) width gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho ISL81485IU.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ISL81485IU phù hợp cho 3 Áp dụngs: Hệ thống tích hợp, Máy thiết bị IoT, Điều khiển công nghiệp.
Hệ thống tích hợp
Xử lý trung tâm trong các ứng dụng tích hợp sử dụng ISL81485IU.
Máy thiết bị IoT
Máy thiết bị kết nối thông minh được cung cấp bởi ISL81485IU.
Điều khiển công nghiệp
Hệ thống tự động hóa và điều khiển sử dụng ISL81485IU.
Dữ liệu tham khảo kỹ thuật cho ISL81485IU — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ISL81486IU |
|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics |
| Package | 8-MSOP | 8-MSOP |
| Maximum Data Rate | 30 Mbps | 30 Mbps |
| Lifecycle Status | Obsolete | Obsolete |
| Mounting Type | Surface mount | Surface mount |
Bảo phân biệt quan trọng
- High-speed balanced communications in a compact package (vsISL81486IU)
- One device supports two balanced bus standards (vsISL81486IU)
- Single-transceiver implementation reduces board area (vsISL81486IU)
Ghi chú thiết kế
Route the differential pair as a closely coupled pair with continuous reference-plane geometry and minimize stubs, vias, and branch points. At 30 Mbps, discontinuities and unbalanced loading can degrade the differential signal. Keep the transceiver close to the connector and place termination components near the bus interface so that reflections are controlled without creating long high-frequency current loops.
Decouple the 5 V transceiver supply close to the device and keep the return-current path continuous beneath the IC and connector. Use the manufacturer-recommended capacitance and voltage rating, and account for supply ripple when the bus reaches its maximum 30 Mbps data rate. Avoid sharing a narrow supply path with unrelated switching or motor-current loads.
Do not substitute the ISL81485IU-T as a different functional alternative; it represents a distinct ordering or packing suffix for the same ISL81485 device. Before fitting an alternative transceiver, compare pin names, enable polarity, receiver-enable behavior, propagation delay, bus impedance, common-mode range, and power-off state. A shared MSOP outline alone does not guarantee behavioral compatibility.
For RS-485 networks, use an appropriate topology and termination strategy rather than adding termination indiscriminately to every node. Stubs should be minimized, especially on high-speed networks. The differential interface can improve noise immunity, but common-mode transients still require appropriate protection and grounding, particularly where the transceiver is connected to long external cables.
Thông tin tuân thủ
No definitive RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified in the available records. The ISL81485IU and ISL81486IU are identified as obsolete.