ISL81485IU - 30Mbps RS-485/RS-422 Transceiver | Renesas
Артикул: ISL81485IU ✗ Снят с производстваISL81485IU Обзор
An RS-485/RS-422 transceiver is an interface IC that converts single-ended digital signals into balanced differential signals for transmission and converts received differential signals back into a logic-level output. RS-422 is commonly associated with point-to-point, balanced communication, while RS-485 supports multipoint bus networks and driver inhibit capability. The ISL81485IU belongs to the broader hierarchy of interface transceivers, serial communication ICs, and semiconductors used to connect digital equipment over copper cabling.
The principal features of the ISL81485IU are its 5 V operation, 30 Mbps maximum signaling rate, and support for both RS-485 and RS-422 communication standards. Its single-transceiver format allows a compact design to implement a bidirectional link by connecting the driver and receiver controls to the same digital interface. The manufacturer datasheet describes a larger output voltage and higher data rate as beneficial for high-speed applications, while its BiCMOS process supports the demanding output and receiver requirements of balanced differential links.
In an RS-485 network, the differential bus reduces sensitivity to common-mode noise and allows data to be transmitted over longer cable runs than a conventional single-ended interface. The 30 Mbps capability makes the device relevant to factory automation, industrial control, data acquisition, and embedded instrumentation systems that need a compact point-to-point or multidrop communications interface. When two transceivers are used on a shared bus, driver-enable and receiver-enable controls determine which node drives or listens at any given time.
The principal design tradeoff is that a high-speed differential transceiver requires careful attention to board layout, termination, decoupling, grounding, and protection. The 5 V supply should be filtered near the device, and routed differential traces should remain closely coupled. Cabling and connector geometry also influence signal integrity, particularly at the maximum 30 Mbps operating rate.
This page combines the manufacturer specifications, interface-function analysis, sourcing fields, and practical RS-485/RS-422 design guidance to support component selection and PCB implementation. It also distinguishes confirmed drop-in candidates from related devices that require additional pin, timing, and protocol verification before substitution.
Аналоги без доработки для ISL81485IU — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с ISL81485IU (тот же форм-фактор и посадочное место) — отличается по Maximum Data Rate, Package, Product Type.
ISL81486IU
✅ Прямая заменаУточнить цену
Открыть даташит →ISL81485IU Характеристики
| Product Type | Single RS-485/RS-422 line transceiver |
| Напряжение питания | 5 V |
| Maximum Data Rate | 30 Mbps |
| Supported Standards | RS-485 and RS-422 |
| Process Technology | BiCMOS |
| Number of Transceivers | 1 |
| Корпус | 8-pin MSOP, 0.118 in (3.00 mm) width |
| Тип монтажа | Surface mount |
| Signal Interface | Balanced differential |
Руководство по цоколевке ISL81485IU в корпусе 8-pin msop, 0.118 in (3.00 mm) width
Цоколевка для ISL81485IU (корпус 8-pin msop, 0.118 in (3.00 mm) width). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для ISL81485IU.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
ISL81485IU подходит для 3 применениеs: Встраиваемые системы, Устройства IoT, Промышленная автоматизация.
Встраиваемые системы
Основная обработка во встраиваемых приложениях с использованием ISL81485IU.
Устройства IoT
Умные подключённые устройства на базе ISL81485IU.
Промышленная автоматизация
Системы автоматизации и управления с использованием ISL81485IU.
Справочные инженерные данные для ISL81485IU — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | ISL81486IU |
|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics |
| Package | 8-MSOP | 8-MSOP |
| Maximum Data Rate | 30 Mbps | 30 Mbps |
| Lifecycle Status | Obsolete | Obsolete |
| Mounting Type | Surface mount | Surface mount |
Ключевые отличия
- High-speed balanced communications in a compact package (против ISL81486IU)
- One device supports two balanced bus standards (против ISL81486IU)
- Single-transceiver implementation reduces board area (против ISL81486IU)
Заметки по проектированию
Route the differential pair as a closely coupled pair with continuous reference-plane geometry and minimize stubs, vias, and branch points. At 30 Mbps, discontinuities and unbalanced loading can degrade the differential signal. Keep the transceiver close to the connector and place termination components near the bus interface so that reflections are controlled without creating long high-frequency current loops.
Decouple the 5 V transceiver supply close to the device and keep the return-current path continuous beneath the IC and connector. Use the manufacturer-recommended capacitance and voltage rating, and account for supply ripple when the bus reaches its maximum 30 Mbps data rate. Avoid sharing a narrow supply path with unrelated switching or motor-current loads.
Do not substitute the ISL81485IU-T as a different functional alternative; it represents a distinct ordering or packing suffix for the same ISL81485 device. Before fitting an alternative transceiver, compare pin names, enable polarity, receiver-enable behavior, propagation delay, bus impedance, common-mode range, and power-off state. A shared MSOP outline alone does not guarantee behavioral compatibility.
For RS-485 networks, use an appropriate topology and termination strategy rather than adding termination indiscriminately to every node. Stubs should be minimized, especially on high-speed networks. The differential interface can improve noise immunity, but common-mode transients still require appropriate protection and grounding, particularly where the transceiver is connected to long external cables.
Информация о соответствии
No definitive RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified in the available records. The ISL81485IU and ISL81486IU are identified as obsolete.