ISL81485IU - 30Mbps RS-485/RS-422 Transceiver | Renesas
MPN: ISL81485IU ✗ پایان تولیدISL81485IU نمای کلی
An RS-485/RS-422 transceiver is an interface IC that converts single-ended digital signals into balanced differential signals for transmission and converts received differential signals back into a logic-level output. RS-422 is commonly associated with point-to-point, balanced communication, while RS-485 supports multipoint bus networks and driver inhibit capability. The ISL81485IU belongs to the broader hierarchy of interface transceivers, serial communication ICs, and semiconductors used to connect digital equipment over copper cabling.
The principal features of the ISL81485IU are its 5 V operation, 30 Mbps maximum signaling rate, and support for both RS-485 and RS-422 communication standards. Its single-transceiver format allows a compact design to implement a bidirectional link by connecting the driver and receiver controls to the same digital interface. The manufacturer datasheet describes a larger output voltage and higher data rate as beneficial for high-speed applications, while its BiCMOS process supports the demanding output and receiver requirements of balanced differential links.
In an RS-485 network, the differential bus reduces sensitivity to common-mode noise and allows data to be transmitted over longer cable runs than a conventional single-ended interface. The 30 Mbps capability makes the device relevant to factory automation, industrial control, data acquisition, and embedded instrumentation systems that need a compact point-to-point or multidrop communications interface. When two transceivers are used on a shared bus, driver-enable and receiver-enable controls determine which node drives or listens at any given time.
The principal design tradeoff is that a high-speed differential transceiver requires careful attention to board layout, termination, decoupling, grounding, and protection. The 5 V supply should be filtered near the device, and routed differential traces should remain closely coupled. Cabling and connector geometry also influence signal integrity, particularly at the maximum 30 Mbps operating rate.
This page combines the manufacturer specifications, interface-function analysis, sourcing fields, and practical RS-485/RS-422 design guidance to support component selection and PCB implementation. It also distinguishes confirmed drop-in candidates from related devices that require additional pin, timing, and protocol verification before substitution.
جایگزینهای drop-in برای ISL81485IU — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای ISL81485IU (همان فرمفاکتور و فوتپرینت) — متفاوت در Maximum Data Rate, Package, Product Type.
ISL81486IU
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←ISL81485IU مشخصات
| Product Type | Single RS-485/RS-422 line transceiver |
| ولتاژ تغذیه | 5 V |
| Maximum Data Rate | 30 Mbps |
| Supported Standards | RS-485 and RS-422 |
| Process Technology | BiCMOS |
| Number of Transceivers | 1 |
| بستهبندی | 8-pin MSOP, 0.118 in (3.00 mm) width |
| نوع نصب | Surface mount |
| Signal Interface | Balanced differential |
راهنمای پیکربندی پین ISL81485IU 8-pin msop, 0.118 in (3.00 mm) width
پیکربندی پین برای ISL81485IU (پکیج 8-pin msop, 0.118 in (3.00 mm) width). شمارهگذاری پایهها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعملهای لحیمکاری به آن مراجعه کنید.
داده پینآوت تفصیلی موجود نیست برای ISL81485IU.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
ISL81485IU مناسب است برای 3 کاربردs: سیستمهای نهفته, دستگاههای IoT, کنترل صنعتی.
سیستمهای نهفته
پردازش هسته در کاربردهای نهفته با استفاده از ISL81485IU.
دستگاههای IoT
دستگاههای هوشمند متصل با توان ISL81485IU.
کنترل صنعتی
سیستمهای اتوماسیون و کنترل با استفاده از ISL81485IU.
دادههای مرجع مهندسی برای ISL81485IU — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | ISL81486IU |
|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics |
| Package | 8-MSOP | 8-MSOP |
| Maximum Data Rate | 30 Mbps | 30 Mbps |
| Lifecycle Status | Obsolete | Obsolete |
| Mounting Type | Surface mount | Surface mount |
تفاوتهای کلیدی
- High-speed balanced communications in a compact package (در مقابلISL81486IU)
- One device supports two balanced bus standards (در مقابلISL81486IU)
- Single-transceiver implementation reduces board area (در مقابلISL81486IU)
یادداشتهای طراحی
Route the differential pair as a closely coupled pair with continuous reference-plane geometry and minimize stubs, vias, and branch points. At 30 Mbps, discontinuities and unbalanced loading can degrade the differential signal. Keep the transceiver close to the connector and place termination components near the bus interface so that reflections are controlled without creating long high-frequency current loops.
Decouple the 5 V transceiver supply close to the device and keep the return-current path continuous beneath the IC and connector. Use the manufacturer-recommended capacitance and voltage rating, and account for supply ripple when the bus reaches its maximum 30 Mbps data rate. Avoid sharing a narrow supply path with unrelated switching or motor-current loads.
Do not substitute the ISL81485IU-T as a different functional alternative; it represents a distinct ordering or packing suffix for the same ISL81485 device. Before fitting an alternative transceiver, compare pin names, enable polarity, receiver-enable behavior, propagation delay, bus impedance, common-mode range, and power-off state. A shared MSOP outline alone does not guarantee behavioral compatibility.
For RS-485 networks, use an appropriate topology and termination strategy rather than adding termination indiscriminately to every node. Stubs should be minimized, especially on high-speed networks. The differential interface can improve noise immunity, but common-mode transients still require appropriate protection and grounding, particularly where the transceiver is connected to long external cables.
اطلاعات انطباق
No definitive RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified in the available records. The ISL81485IU and ISL81486IU are identified as obsolete.