LM3409HVMY/NOPB - 42V PFET Buck LED Controller, HVSSOP-10 | TI
部品番号: LM3409HVMY/NOPB ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $2.45 | $2.45 |
| 10 | $2.18 | $21.80 |
| 100 | $1.92 | $192.00 |
| 500 | $1.65 | $825.00 |
| 1,000 | $1.4 | $1,400.00 |
LM3409HVMY/NOPB 概要
An LED driver controller is a power management IC that regulates current through an LED string rather than voltage. Buck (step-down) controllers use an external switching MOSFET and inductor to deliver current at a lower average voltage than the input, achieving high efficiency (typically >90%) versus resistive or linear current limiters. Buck controllers sit hierarchically below constant-current drivers and above DC-DC switching regulators in the power management IC taxonomy.
Key features include wide VIN from 6V to 42V (HV suffix), high-side differential current sense with low adjustable threshold voltage that eliminates the need for a ground-side sense resistor, fast output enable/disable for PWM dimming, and thermally enhanced HVSSOP package. The controller supports analog dimming via the ADIM input and PWM dimming via the EN pin, with switching frequency adjustable up to 1 MHz using a single external resistor.
The architecture uses a peak-current-mode control loop that monitors voltage across a high-side sense resistor placed in series with the LED load. Because the current sense is high-side, ground-referenced LED strings and grounded heat sinks can be used without introducing ground-loop errors. The HVSSOP-10 package includes an exposed thermal pad (PowerPAD) for low thermal resistance and high power dissipation capability.
Typical applications span high-brightness LED drivers for signage and architectural lighting, MR-Stage flash, MR-16 bulbs, automotive LED headlights and DRLs, and constant-current sources for industrial illumination. Wide input range suits both 12V and 24V bus architectures plus battery-direct-supply 36V Li-ion stacks.
When designing with this device, pay close attention to inductor and sense-resistor selection: inductor value sets converter ripple current, while sense resistor value sets average LED current. Use the exposed pad for PCB thermal relief to handle continuous high-current operation.
ドロップイン代替品: LM3409HVMY/NOPB — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: LM3409HVMY/NOPB （同一形状・フットプリント） — 相違点: Package, Topology, Dimming Method, Operating Temperature.
クイック比較ツール — 並列比較する代替部品を選択:
LM3409HVMY/NOPB
✅ ドロップイン✓ 在庫あり
$1.4 / 個
データシートを見る →LM3409HV-Q1MY/NOPB
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
LM3409HVMYX/NOPB
✅ ドロップイン📋 参考代替品（カタログ未掲載）
LM3409HVMY/NOPB 最大定格＆電気的特性
| トポロジー | Step-Down (Buck) Controller |
| 入力電圧範囲 | 6 V to 42 V |
| 出力数 | 1 |
| Switch Element | P-channel MOSFET (external) |
| Current Sense Method | High-side differential, adjustable threshold |
| Dimming Control | Analog and PWM |
| Enable/Shutdown | Yes (EN pin, fast output enable/disable) |
| 動作温度 | -40 C to +125 C |
| パッケージ | 10-pin HVSSOP (PowerPAD) |
| 実装タイプ | Surface Mount |
| RoHS ステータス | Compliant |
| Lead Finish | Matte Tin (Pb-free) |
| AEC-Q100 Qualified | No (use LM3409HV-Q1 for automotive) |
LM3409HVMY/NOPB ピン構成
| ピン 1 | VIN — Input supply voltage (6V to 42V) |
| ピン 2 | EN — Enable / PWM dimming input (active-high) |
| ピン 3 | ADIM — Analog dimming input / current reference adjust |
| ピン 4 | RT — Timing resistor for switching frequency |
| ピン 5 | CCS — Compensation capacitor |
| ピン 6 | CS — Current sense comparator input (high-side) |
| ピン 7 | HO — High-side gate drive output (to external PFET) |
| ピン 8 | LO — Low-side gate drive output |
| ピン 9 | GND — Ground |
| ピン 10 | PAD — Exposed thermal pad (PowerPAD), solder to PCB ground plane |
主な用途
LM3409HVMY/NOPB の用途: 6 件s: High-Brightness LED Signage, Automotive LED Headlights and DRLs, Architectural and Stage Lighting, MR-Stage LED Bulb Retrofits, Industrial Constant-Current LED Drivers, Portable LED Flashlights and Worklights.
High-Brightness LED Signage
The LM3409HVMY/NOPB drives constant current through high-brightness LED strings in outdoor signage, channel letters, and architectural accent lighting. Its 6V to 42V input range accepts both 12V and 24V bus supplies plus battery-direct stacks, while the wide VIN tolerance handles load-dump and cold-crank transients common in mobile signage. High-side differential current sense with low adjustable threshold enables ground-referenced LED strings and grounded heat sinks, simplifying thermal design for high-power LED clusters. PWM dimming via the EN pin supports brightness modulation for nighttime dimming or dynamic signage effects, and the 10-pin HVSSOP PowerPAD provides the thermal headroom for continuous high-current operation typical of outdoor LED installations.
おすすめ
Automotive LED Headlights and DRLs
The LM3409HVMY/NOPB forms the constant-current core of automotive LED headlamp, DRL, and fog-light modules. Its HV-suffix 42V input rating tolerates load-dump transients on 12V automotive buses, and high-side current sensing allows the LED module heat sink to be chassis-grounded for improved thermal dissipation. Analog dimming on ADIM and fast PWM dimming on EN support adaptive headlight functions such as cornering lights and high-beam assist. For production automotive designs the AEC-Q100 -Q1 grade (LM3409HV-Q1) should be selected; the non-automotive LM3409HVMY/NOPB is appropriate for non-safety automotive interior and accent lighting where -Q1 is optional.
おすすめ
Architectural and Stage Lighting
Architectural lighting fixtures and stage spotlights benefit from the LM3409HVMY/NOPB wide input voltage range and high-side current sensing. The 6V to 42V input supports 24V professional lighting bus architectures, while high-side differential sense allows the fixture chassis to be grounded without ground-loop-induced LED current errors. PWM dimming on the EN pin delivers smooth, deep dimming down to a few percent without color shift, critical for theatrical and architectural dimming curves. The 10-pin HVSSOP PowerPAD package maintains low junction temperature even in enclosed fixtures with limited airflow, supporting continuous full-brightness operation typical of museum and gallery lighting.
おすすめ
MR-Stage LED Bulb Retrofits
MR-Stage LED retrofit bulbs replacing halogen MR-Stage fixtures need high-efficiency constant-current drivers in thermally constrained form factors. The LM3409HVMY/NOPB fits this role with its small 10-pin HVSSOP PowerPAD footprint, which combines low thermal resistance with the small PCB area required inside MR-Stage bulb housings. The wide 6V to 42V input supports both 12V AC-to-DC adapter supplies and 24V commercial LED bus rails, while analog and PWM dimming compatibility preserves the smooth dimming curves of MR-Stage dimmers. High-side current sense avoids ground loops that can introduce flicker in retrofit installations.
おすすめ
Industrial Constant-Current LED Drivers
Industrial machine-vision and inspection lighting require stable constant-current drivers that reject supply noise and deliver uniform LED brightness across long operating cycles. The LM3409HVMY/NOPB peak-current-mode control with high-side current sensing provides tight regulation of LED current regardless of supply variations on the 24V industrial bus. The 6V to 42V input range accepts direct connection to 24V industrial supplies with generous transient margin, while the HVSSOP PowerPAD package sustains continuous high-current operation in factory-floor fixtures. PWM dimming enables strobe synchronization with camera exposures for machine-vision inspection lines.
おすすめ
Portable LED Flashlights and Worklights
Portable Li-ion powered worklights using 1S to 3S Li-ion battery packs (nominally 3.7V to 11.1V, up to 12.6V fully charged) benefit from the LM3409HVMY/NOPB 6V to 42V input range when paired with a boost front-end. The high-side current sense allows the battery-pack negative terminal to be referenced to the chassis, simplifying mechanical design. PWM dimming via EN supports brightness modes (high, medium, low, strobe) common in worklight and flashlight designs, while the small HVSSOP footprint fits the tight PCBs of handheld products. The thermally enhanced PowerPAD enables continuous high-current output without external heatsinking.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: LM3409HVMY/NOPB — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | LM3409HVMY/NOPB | LM3409HV-Q1MY/NOPB | LM3409HVMYX/NOPB |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 10-pin HVSSOP (PowerPAD) | 10-pin HVSSOP (PowerPAD) - same | 10-pin HVSSOP (PowerPAD) - same | 10-pin HVSSOP (PowerPAD) - same |
| Input Voltage Range | 6V to 42V | 6V to 42V | 6V to 42V | 6V to 42V |
| AEC-Q100 Automotive Qualified | No | No | Yes | No |
| Topology | PFET Buck Controller | PFET Buck Controller | PFET Buck Controller | PFET Buck Controller |
| Current Sense | High-side differential, adjustable threshold | High-side differential | High-side differential | High-side differential |
| Dimming Control | Analog and PWM | Analog and PWM | Analog and PWM | Analog and PWM |
| Packaging Form | Cut Tape (smaller reel) | Cut Tape | Cut Tape / -Q1 suffix | Tape and Reel (larger reel) |
主な差別化要因
- High-side differential current sense eliminates ground-loop errors （vs Ground-side sense LED drivers)
- Wide 6V to 42V input voltage range (HV suffix) （vs LM3409 (non-HV) version)
- 10-pin HVSSOP PowerPAD with thermally enhanced exposed pad （vs Standard MSOP packages)
設計ノート
Estimated: At VIN=24V, VLED=12V, ILED=1A, the external PFET and diode dissipate approximately 12W. Size the external PFET for VDSS greater than the maximum VIN plus margin and RDSON low enough to keep conduction loss under 1W. The HVSSOP controller itself dissipates only gate-drive loss plus a few mA quiescent; verify junction temperature using the HVSSOP PowerPAD theta_JA from the datasheet.
The 10-pin HVSSOP package uses an exposed thermal pad (PowerPAD) that MUST be soldered to a PCB copper area for proper heat sinking. Allocate a thermal pad copper pour of at least 100 mm^2 on top and bottom layers stitched with thermal vias, per TI PowerPAD application notes. Without the exposed-pad solder connection, thermal resistance increases dramatically and the device can overheat at high duty cycles.
Place the high-side current-sense resistor RSNS as close as possible to the LED load return and route the CS pin traces as a true Kelvin connection to avoid switching noise corrupting the current measurement. Keep the switching node (PFET drain, inductor, diode) traces short and away from the CS and ADIM analog traces. Use a ground plane on the bottom layer to minimize EMI and provide thermal relief for the PowerPAD.
Do not omit the bootstrap capacitor on the HO pin if the topology requires it (refer to the datasheet application circuit). Select the RT resistor to set switching frequency - too low a frequency increases inductor ripple and acoustic noise; too high increases switching losses. Verify the chosen inductor saturation rating handles peak current (ILED plus half of ripple current) plus margin.
コンプライアンス情報
RoHS compliant per TI product page. Not AEC-Q100 qualified; use LM3409HV-Q1MY/NOPB for automotive.
