MK10DN512ZAB10R - Kinetis K10 ARM Cortex-M4 MCU 512KB WLCSP | NXP
部品番号: MK10DN512ZAB10R ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $8.95 | $8.95 |
| 10 | $8.06 | $80.60 |
| 100 | $7.16 | $716.00 |
| 500 | $6.44 | $3,220.00 |
| 1,000 | $5.73 | $5,730.00 |
MK10DN512ZAB10R 概要
A microcontroller (MCU) is a single-chip computer containing a processor core, non-volatile program memory, volatile data memory, and a fixed set of peripherals. Within the embedded hierarchy, an MCU sits below a microprocessor (MPU) because it integrates memory and peripherals on-die. Kinetis K-series MCUs target mixed-signal industrial applications, distinct from K-series L (low-power) and M (motor-control) derivatives. NXP Kinetis K10 sits in the value-line mixed-signal MCU segment, balancing analog integration, CPU performance, and low-power modes for portable instrumentation, factory automation, and consumer devices.
Key features highlighted in the manufacturer datasheet include 512 KB flash, 128 KB SRAM, a 100 MHz Cortex-M4 core, integrated USB 2.0 full-speed OTG controller, multiple serial peripherals (UART, SPI, I2C), and a 12-channel DMA. The 16-bit ADC supports up to 16 single-ended inputs with hardware averaging, and the 12-bit DAC enables precise analog output for setpoint generation. The WLCSP package eliminates the lead-frame, reducing PCB area to roughly the silicon die size and offering excellent electrical performance at high frequencies. Low-power Run, Wait, Stop, and VLLS modes allow the device to draw microamps in deep sleep, suitable for battery-powered sensors.
Typical applications include industrial sensor transmitters, portable medical instrumentation, USB peripherals, motor control for small BLDC/PMSM stages, and low-power IoT edge nodes where the mixed-signal front-end removes the need for separate ADC/DAC ICs. Designers typically choose the MK10DN512ZAB10R when PCB area is critical and on-board analog conversion is required. When sourcing, note that the trailing 'R' suffix denotes Tape and Reel packaging, while the 'AB10' segment encodes the 100 MHz speed grade and WLCSP package option.
ドロップイン代替品: MK10DN512ZAB10R — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: MK10DN512ZAB10R （同一形状・フットプリント） — 相違点: Package, ADC, DAC, USB, Core Architecture.
クイック比較ツール — 並列比較する代替部品を選択:
MK10DN512ZVLQ10
✅ ドロップイン📋 参考代替品（カタログ未掲載）
MK10DN512ZVMC10R
✅ ドロップイン📋 参考代替品（カタログ未掲載）
MK22FN1M0AVLK12
✅ ドロップイン✓ 在庫あり
$7.95 / 個
データシートを見る →MK60DN512ZVLQ10
✅ ドロップイン✓ 在庫あり
$9.3 / 個
データシートを見る →MK24FN1M0VDC12
✅ ドロップイン✓ 在庫あり
$9.75 / 個
データシートを見る →MK10DN512ZAB10R 最大定格＆電気的特性
| Core Architecture | ARM Cortex-M4 |
| Core Bit Width | 32-bit |
| Maximum CPU Frequency | 100 MHz |
| Program Flash Memory | 512 KB (512K x 8) |
| パッケージ | WLCSP |
| ADC | 16-bit integrated |
| DAC | 12-bit integrated |
| USB | USB 2.0 Full-Speed OTG |
| DMA Channels | 12 |
| 実装タイプ | Surface Mount |
| RoHS ステータス | Compliant |
| Series | Kinetis K10 |
MK10DN512ZAB10R wlcsp ピン配置ガイド
MK10DN512ZAB10R (wlcsp パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: MK10DN512ZAB10R.
詳細は データシート をご参照ください。
主な用途
MK10DN512ZAB10R の用途: 6 件s: Industrial Sensor Transmitters, Portable Medical Instrumentation, USB Peripherals and HID Devices, Small Motor Control - BLDC / PMSM, Battery-Powered IoT Edge Nodes, Consumer HMI Touch Interfaces.
Industrial Sensor Transmitters
The MK10DN512ZAB10R's integrated 16-bit ADC, 12-bit DAC, and Cortex-M4 DSP extensions make it well-suited for industrial sensor transmitters. The MCU can digitize multi-channel analog sensor inputs with hardware averaging, apply digital filtering, then drive a 4-20 mA loop via the 12-bit DAC. The 100 MHz core sustains real-time linearization and RTD/cold-junction compensation without offloading to a separate DSP. Compared with a discrete ADC + 8-bit processor solution, the MK10DN512ZAB10W shrinks the BOM while keeping 512 KB flash for protocol stacks such as HART or IO-Link. The WLCSP footprint allows the entire transmitter to fit inside a standard DIN form-factor head, and low-power VLLS modes extend battery life in loop-powered 4-20 mA designs.
おすすめ
Portable Medical Instrumentation
Portable medical devices such as pulse oximeters, glucose meters, and handheld ECG monitors benefit from the MK10DN512ZAB10R's mixed-signal integration and tiny WLCSP footprint. The 16-bit ADC captures bio-potential or photodiode signals directly, while the Cortex-M4 DSP extensions run real-time DSP filters (e.g., moving average, FFT) without external accelerators. The 512 KB flash holds both the application and an IEC 62304-grade firmware, while 128 KB SRAM is adequate for waveform buffering. Low-power Run and VLLS modes reduce average current below 50 uA between samples, supporting coin-cell or Li-ion battery operation. The integrated USB 2.0 FS OTG enables direct charging and data upload without a separate interface IC, lowering BOM cost for high-volume medical disposables.
おすすめ
USB Peripherals and HID Devices
The MK10DN512ZAB10R's integrated USB 2.0 full-speed OTG controller with on-chip transceiver makes it ideal for USB peripherals such as HID controllers, data loggers, and diagnostic tools. The USB peripheral can be addressed without an external PHY, saving PCB area and BOM cost. The 512 KB flash accommodates the USB stack plus application code, while 128 KB SRAM supports USB endpoint buffering and protocol handling. The Cortex-M4 runs at 100 MHz, more than adequate for full-speed USB at 12 Mbps. The WLCSP package suits compact dongle designs, and low-power modes help meet USB suspend current requirements. Compared with using an external USB-serial bridge IC, the integrated USB reduces BOM by 1-2 USD per unit and simplifies FCC/CE compliance.
おすすめ
Small Motor Control - BLDC / PMSM
The MK10DN512ZAB10R's mixed-signal integration and Cortex-M4 DSP extensions make it a viable MCU for small brushless DC (BLDC) and permanent-magnet synchronous motor (PMSM) control stages such as fans, pumps, and small drones. The 16-bit ADC samples phase currents, while the on-chip eFlexPWM timer generates complementary PWM with dead-time insertion for the half-bridge gate drivers. The 100 MHz core executes FOC (field-oriented control) at rates up to 10 kHz with adequate headroom. The 12-bit DAC can drive an analog torque reference or signal a debug node. The 512 KB flash is sufficient to hold the FOC algorithm plus telemetry, while 128 KB SRAM handles Park/Clarke transform scratch buffers. For higher-current or higher-RPM motors, an external gate driver is required.
おすすめ
Battery-Powered IoT Edge Nodes
The MK10DN512ZAB10R's integrated peripherals and low-power modes make it a strong choice for battery-powered IoT edge nodes. The 16-bit ADC samples analog sensors, the DAC drives analog actuators, and the USB OTG provides direct Li-ion charging. The WLCSP package fits within 4x4 mm PCB area - ideal for coin-cell wearables. Low-power Run, Wait, Stop, and VLLS modes reduce quiescent current below 5 uA in deep sleep, extending battery life to 5+ years on a CR2032 for periodic sampling. The 512 KB flash accommodates application code, a secure bootloader, and an OTA update staging partition. Compared with a discrete analog-front-end + WiFi SoC, the MK10DN512ZAB10R eliminates one IC while keeping the BOM small and predictable.
おすすめ
Consumer HMI Touch Interfaces
The MK10DN512ZAB10R's integrated peripherals support consumer HMI touch interfaces such as appliance control panels and small industrial HMIs. The 16-bit ADC reads resistive touch overlays, the 12-bit DAC drives an LED backlight brightness control, and the Cortex-M4 DSP runs the touch-sensing algorithm in real time. The 512 KB flash accommodates an LVGL-style graphics library and a USB stack for firmware updates. The WLCSP package fits inside a slim bezel, and the 100 MHz core renders simple graphics at 30+ fps. Low-power Wait mode lets the panel enter a screen-off state without losing touch wakeup capability. Compared with a separate touch controller IC, the integrated ADC reduces BOM while keeping latency low for finger-tracking gestures.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MK10DN512ZAB10R — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MK10DN512ZVLQ10 | MK10DN512ZVMC10R | MK22FN1M0AVLK12 | MK60DN512ZVLQ10 | MK24FN1M0VDC12 |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | WLCSP | LQFP-144 - different footprint | MAPBGA-144 - different footprint | LQFP-80 - different footprint | LQFP-144 - different footprint | MAPBGA-144 - different footprint |
| Core | ARM Cortex-M4 | ARM Cortex-M4 | ARM Cortex-M4 | ARM Cortex-M4 | ARM Cortex-M4 | ARM Cortex-M4 |
| Max CPU Frequency | 100 MHz | 100 MHz | 100 MHz | 120 MHz | 100 MHz | 120 MHz |
| Flash Memory | 512 KB | 512 KB | 512 KB | 1 MB | 512 KB | 1 MB |
| USB | USB 2.0 Full-Speed OTG | USB 2.0 Full-Speed OTG | USB 2.0 Full-Speed OTG | USB 2.0 High-Speed OTG | USB 2.0 High-Speed OTG + Ethernet | USB 2.0 Full-Speed OTG |
| Integrated ADC | 16-bit | 16-bit | 16-bit | 16-bit | 16-bit | 16-bit |
| Family | Kinetis K10 | Kinetis K10 | Kinetis K10 | Kinetis K22 | Kinetis K60 | Kinetis K24 |
主な差別化要因
- Smallest-footprint K10 variant - WLCSP （vs MK10DN512ZVLQ10)
- Integrated mixed-signal front-end （vs MK22FN1M0AVLK12)
- Lower-power variant within Kinetis K-series （vs MK60DN512ZVLQ10)
設計ノート
The MK10DN512ZAB10R WLCSP package has limited thermal mass compared to LQFP equivalents; in continuous high-CPU-load use cases the junction temperature can rise significantly. For applications with sustained 100 MHz operation, ensure the PCB has a small copper pour beneath the WLCSP thermal balls to dissipate heat. The K10P100M100SF2 datasheet specifies thermal characteristics in the WLCSP variant - consult the package thermal model before sealing the MCU inside an enclosed sensor head.
Place the 16 MHz external crystal within 5 mm of the XTAL pins, with a ground guard ring to reduce EMI. Decouple VDD/VSS pairs with a 100 nF X7R 0402 ceramic capacitor per supply pin, plus a bulk 4.7 uF tantalum or ceramic on the regulator rail. For WLCSP variants, place 0.1 uF decoupling directly under each supply ball on the opposite PCB side to minimize loop inductance. NXP application note AN4830 provides Kinetis hardware design guidance.
Do not confuse the K10 (mixed-signal), K20 (connectivity), K60 (Ethernet+HS USB), and K70 (LCD) families - they share the same ARM Cortex-M4 core but pinouts and peripherals differ. The 'AB10' suffix in MK10DN512ZAB10R encodes the 100 MHz speed grade and WLCSP package option; sourcing the wrong speed variant will fail timing-closure checks. Always verify the exact MPN against the NXP product selector before placing volume POs.
Use a low-dropout regulator with at least 100 mA headroom for the MK10DN512ZAB10R's peak current draw during ADC sampling and flash writes. The internal voltage regulator requires a 4.7 uF bulk capacitor on the internal regulator output pin. Enable the on-chip voltage regulator monitor in software to detect brown-out conditions during flash programming; this prevents partial writes that can brick the part in the field.
コンプライアンス情報
RoHS compliance confirmed via Mouser product listing. Not AEC-Q100 qualified - the MK10DN512ZAB10R targets industrial/consumer; for automotive, evaluate the K10x AEC-Q100 variants. Halogen-free status not explicitly listed in verified data.
