마이크로컨트롤러

제품 (20,000+)

MC9S12C96MFAE - 16-bit HCS12 MCU, 96KB Flash, 48-LQFP | NXP
MC9S12C96MFAE

MC9S12C96MFAE - 16-bit HCS12 MCU, 96KB Flash, 48-LQFP | NXP

The NXP MC9S12C96MFAE is a 16-bit HCS12 microcontroller with 96KB on-chip Flash, 4KB RAM, and a 25MHz CISC core, housed in a 48-pin LQFP (7x7 mm) package. It integrates a CAN 2.0 controller, SCI/SPI serial interfaces, PWM channels, and a watchdog timer, targeting cost-sensitive automotive body and industrial network nodes. The 2.97V to 5.5V single-supply operation with an internal bandgap voltage regulator simplifies board design versus parts needing multiple rails. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash/ROM), working memory (RAM), and a rich set of programmable peripherals. The HCS12 family is a 16-bit CISC architecture that evolved from the original Motorola/Freescale HC12, providing deterministic interrupt latency, a background debug mode (BDM) interface, and a CPU12 instruction set that is largely object-code compatible with the older HC11. Within the broader taxonomy, the HCS12 sits under 16-bit MCU -> microcontroller -> embedded processor -> semiconductor. The S12C sub-family is the cost-optimized tier within HCS12, sharing the same peripheral IP with the higher-pin S12G/S12P families while trimming 12 layers to the minimum footprint for LIN/CAN edge nodes. Key features include 31 GPIO lines, an on-chip PLL for flexible bus-clock generation from an external crystal or resonator, a 16-channel 10-bit ADC, an 8-channel PWM module, and a CAN 2.0A/B controller compatible with DeviceNet and CANopen stacks. The 96KB Flash is split into a 96K x 8 array with hardware-secured block protection for bootloader/application partitioning, and 4KB RAM supports typical RTOS or foreground/background automotive stacks. Architecturally the device uses a von-Neumann style unified memory map with 23-bit Flash paging, a 16-bit ALU, and a hardware multiply/divide engine. The integrated voltage regulator (VREG) generates the 2.5V internal digital supply from the external 5V rail, eliminating the need for an external LDO in many 5V-only body modules. This combined with on-chip CAN, SCI, and SPI makes the part a one-chip solution for distributed automotive networks. Typical applications include CAN-connected body control modules (BCM), instrument cluster sub-MCUs, HVAC damper controllers, LIN/CAN gateway nodes, and industrial sensor interface boards. In automotive body networks the part typically acts as a slave node communicating over CAN at 125-500 kbps with a master BCM. The AEC-Q100 qualification and 48-pin LQFP expose pad package also support harsh-environment mounting. When designing with this device, ensure the BDM debug header is brought out to a 6-pin standard debug connector to allow in-circuit Flash programming and runtime debug. Decouple VDD/VSS with 100nF + 4.7uF ceramic close to the pins, and route the EXTAL/XTAL traces as short and symmetric as possible to avoid PLL jitter. Designers should also verify the latest PCN status - NXP has marked this part NRND. This page synthesizes distributor pricing, verified drop-in alternatives (same NXP S12C family), and practical design notes not aggregated on any single distributor page.

견적 요청 문의하기
MC9S12C96MPBE - HCS12 16-Bit MCU 96KB Flash 52-LQFP | NXP
MC9S12C96MPBE

MC9S12C96MPBE - HCS12 16-Bit MCU 96KB Flash 52-LQFP | NXP

The NXP MC9S12C96MPBE is a 16-bit HCS12 microcontroller (MCU) with 96KB of on-chip Flash program memory and 4KB of RAM, operating at up to 25 MHz core speed and housed in a 52-pin LQFP package (10 mm x 10 mm body). It belongs to the cost-effective MC9S12C-family and was originally designed by Freescale Semiconductor (now part of NXP) for general-purpose Industrial and Automotive network applications. The integrated peripherals include CANbus, SCI, SPI, EBI/EMI, PWM, a Watchdog Timer, and a Power-On Reset block, with 35 programmable I/O lines. A 16-bit microcontroller (MCU) is a single-chip computing engine that integrates a CPU, program memory (Flash), data memory (RAM), and a configurable set of peripherals around the CPU to handle real-time control tasks. The MC9S12C96 sits inside the Freescale/NXP automotive MCU hierarchy as: HCS12 -> CPU12 -> 16-bit CISC core; S12C family -> cost-optimized derivative; microcontroller -> embedded processor -> semiconductor device. Compared with 8-bit MCUs such as the 8051 or PIC16, the HCS12's 16-bit datapath and 25 MHz CPU12 core deliver higher arithmetic throughput while retaining deterministic interrupt response. Key features include: 96KB single-voltage Flash with in-application reprogramming, 4KB SRAM, an internal oscillator that simplifies BOM by removing the external crystal in many designs, 35 GPIO, and 8-bit PWM channels suitable for motor control loops. Communication is provided by one CAN 2.0 A/B module, one SCI (UART) and one SPI channel, plus the external bus interface (EBI/EMI) for memory expansion. The CPU12 core uses a 16-bit CISC architecture with an instruction pipeline, addressing up to 1 MB of linear memory through banked windows. Bus speed is derived from the PLL-multiplied oscillator and supports single-wire background debug mode (BDM) for non-intrusive in-circuit programming and field updates. Typical applications include automotive body controllers, HVAC actuators, instrument clusters, industrial CAN nodes, and sensor-interface boards where the CAN bus is the primary network. The wide supply range (2.5V/5V) lets the same board host either 3.3V or 5V peripherals. When designing with this device, budget for proper decoupling near every VDD/VSS pin pair and place the CAN transceiver close to the MCU to keep the bus-stub length short. The BDM interface is recommended for production firmware programming because it allows in-application updates without pulling the part out of the socket.

견적 요청 문의하기
MC9S12D32CFUE - 16-bit HCS12 MCU, 32KB Flash, 80-QFP | NXP
MC9S12D32CFUE

MC9S12D32CFUE - 16-bit HCS12 MCU, 32KB Flash, 80-QFP | NXP

The NXP Semiconductors MC9S12D32CFUE is a 16-bit HCS12 family microcontroller with 32 KB of on-chip Flash, 25 MHz CPU clock, and an 80-pin QFP (14x14 mm) package. It is part of the S12D sub-family, originally launched by Freescale (pre-NXP acquisition) and now classified NRND (Not Recommended for New Designs) by NXP. The MCU integrates CAN, SCI, SPI, and I2C peripherals, making it suitable for automotive body and chassis ECUs as well as industrial motor and sensor nodes. A 16-bit microcontroller (MCU) is an integrated computing core that executes instructions on 16-bit data paths, providing higher arithmetic precision than 8-bit devices while remaining simpler and cheaper than 32-bit Cortex-M parts. Within the broader taxonomy, the HCS12 belongs to the S12 family of automotive microcontrollers (MCU -> 16-bit MCU -> HCS12 -> S12D sub-family -> automotive microcontroller). The MC9S12D32CFUE runs from a single 2.5 V or 5 V supply, supports an external bus interface (8-bit narrow mode), and is built around the BGND/BDM debug module that allows non-intrusive in-circuit development. Key features of this part include 32 KB of Flash program memory, 2 KB of RAM, 1 KB of EEPROM, an 8-channel 10-bit ADC, an 8-channel PWM timer, a CAN 2.0 controller, dual SCI (UART) channels, SPI, and I2C. The S12D core is a CISC architecture with full 16-bit internal data paths, supporting single-wire BDM (Background Debug Mode) for non-intrusive in-circuit programming and debugging. The 80-QFP package is pin-compatible across most S12D family members, allowing easy memory-scaling upgrades. Typical applications include automotive body controllers, HVAC control panels, instrument clusters, industrial sensor hubs, CAN node bridges, and small appliance motor controllers. Because the part is NRND, design engineers should plan migration to an active S12K, S12XS, or S32K1 family member for new programs, while continuing to use the MC9S12D32CFUE in long-lifecycle fielded designs.

견적 요청 문의하기
MC9S12D32MFUE - 16-Bit 25MHz HCS12 MCU | NXP | Automotive
MC9S12D32MFUE

MC9S12D32MFUE - 16-Bit 25MHz HCS12 MCU | NXP | Automotive

The NXP MC9S12D32MFUE is a 16-bit HCS12 microcontroller operating up to 25 MHz, with 32 KB of flash program memory and 59 general-purpose I/O pins in an 80-pin QFP package measuring 14 x 14 mm. It integrates CANbus, I2C, SCI, SPI, PWM, and watchdog peripherals, making it a consolidated embedded-control solution for automotive and industrial equipment. A microcontroller is a programmable semiconductor that executes firmware, reads sensors, controls actuators, and coordinates peripheral devices. The HCS12 core belongs to the MCU hierarchy and combines a 16-bit processor with integrated memory and communications interfaces. Rather than requiring separate interface controllers, the MC9S12D32MFUE places CAN, serial, SPI, timing, and watchdog resources beside the CPU. Verified product data identifies 32 KB of flash organized as 32K x 8, 4K x 8 bytes of RAM, 1K x 8 bytes of EEPROM, and 59 I/O pins. Its communication set includes CANbus, I2C, SCI, and SPI, while PWM supports time-dependent output functions and the watchdog helps protect embedded operation. The part also supports both 2.5 V and 5 V operation according to the supplied comparison data. The S12D architecture provides full 16-bit internal data paths and an external bus that can operate in an 8-bit narrow mode for lower-cost memory interfacing. That combination allows engineers to retain 16-bit processing internally while connecting narrower external devices where appropriate. System integration resources managed by the SIM include clock generation, interrupt control, and bus interfacing. Typical uses include automotive body and chassis controllers, motor-control equipment, industrial automation, CAN-connected sensors, and compact embedded control panels. The 80-QFP footprint supports conventional PCB assembly, while the broad peripheral set can reduce component count in systems that otherwise require separate communication and timing ICs. Design planning must verify exact pin multiplexing, clock setup, memory interfaces, and peripheral electrical limits against the official datasheet before layout. Because the official NXP page identifies the lifecycle state as NRND, long-lived production programs should confirm availability, migration timing, and any approved replacement strategy before committing new designs. This page consolidates verified distributor specifications, lifecycle information, sourcing data, and practical engineering considerations for the MC9S12D32MFUE. It also separates documented facts from unavailable electrical details, helping engineers evaluate this NRND 16-bit MCU without assuming unverified pinout, supply-voltage, or timing parameters.

견적 요청 문의하기
MC9S12D32VFUE - 16-bit HCS12 MCU 32KB Flash 25MHz | NXP
MC9S12D32VFUE

MC9S12D32VFUE - 16-bit HCS12 MCU 32KB Flash 25MHz | NXP

The NXP (Freescale) MC9S12D32VFUE is a 16-bit HCS12 microcontroller featuring 32KB of flash memory, a 25 MHz bus-capable core, and a 10-bit ADC system, housed in an 80-pin QFP (14x14 mm) package. It integrates a rich set of standard on-chip peripherals on the S12D platform, including two asynchronous serial communications interfaces (SCI), an 8-channel input capture/output capture enhanced capture timer, two 8-channel 10-bit analog-to-digital converters, an 8-channel pulse-width modulator (PWM), 20 discrete digital I/O lines, and an Inter-IC Bus (IIC). A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, memory, and programmable peripherals into one chip, forming the lowest tier of embedded processing devices. Within NXP's hierarchy, the S12D family sits under the HCS12/S12 16-bit microcontroller architecture, itself part of the broader automotive and industrial MCU portfolio alongside the S12X and SPC5 lines. Key features of the MC9S12D32VFUE include its CISC HCS12 CPU core clocked up to 25 MHz, 32KB (32K x 8) of on-chip flash program memory, and a fully static design suited to 5V automotive-grade environments. The dual 8-channel 10-bit ADCs allow simultaneous multi-sensor sampling, while the 8-channel PWM supports motor control and lighting applications without external timers. Technically, the S12D architecture uses a system resource mapping unit for clock generation, interrupt control, and bus interfacing, with standard on-chip peripherals connected through the internal bus. The star-connected module design simplifies firmware porting across the S12D memory variants (32KB, 64KB, 128KB), since register maps remain consistent across the family. Typical applications include automotive body electronics, dashboard clusters, HVAC controllers, industrial motor control with PWM-driven actuators, and multi-channel analog sensor acquisition in factory automation, where the 10-bit ADC and 5V noise immunity are practical advantages. When designing with this part, verify the availability status: NXP lists the MC9S12D32VFUE as NRND (Not Recommended for New Designs), so new projects should evaluate family successors while the flash capacity ladder within the same 80-QFP footprint eases migration. This page synthesizes distributor pricing, drop-in alternatives, lifecycle status, and practical design notes not found in the manufacturer datasheet, based on data verified as of 2026-10-18.

견적 요청 문의하기
MC9S12D64CFU - 16-Bit 25MHz HCS12 MCU, 64KB Flash, 80-QFP | NXP
MC9S12D64CFU

MC9S12D64CFU - 16-Bit 25MHz HCS12 MCU, 64KB Flash, 80-QFP | NXP

The NXP Semiconductors MC9S12D64CFU is a 16-bit HCS12 microcontroller IC running at 25 MHz, integrating 64 KB (64K x 8) of Flash program memory in an 80-pin PQFP (QFP 14x14 mm) surface-mount package. It belongs to NXP's MC9S12D family of CISC microcontrollers and is qualified to the AEC-Q100 automotive standard. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), working memory (RAM), peripherals, and I/O onto one die. Within the broader category, the MC9S12D64CFU is a CISC 16-bit MCU using the HCS12 core architecture. The HCS12 hierarchy sits inside the automotive-qualified 16-bit MCU segment, which itself is a branch of the wider microcontroller family tree: 16-bit MCU -> MCU -> microcontroller -> embedded processor -> semiconductor. Compared with 8-bit MCUs (such as HC08 or 8051), the 16-bit HCS12 offers a richer instruction set, larger linear address space, and on-chip peripherals suited to body and chassis ECUs. Key features of the MC9S12D64CFU include 64 KB of on-chip Flash for application code, 4 KB of RAM for data, an integrated 8-channel 10-bit A/D converter for analog sensor acquisition, and 59 general-purpose I/O pins for digital interfacing. Communication peripherals in the HCS12D family typically include multiple SCI (UART), SPI, and IIC (I2C) ports, plus PWM channels and timers, although specific peripheral counts for the MC9S12D64CFU need to be confirmed in the device datasheet. The 25 MHz bus clock and 16-bit data path allow deterministic interrupt latency and predictable execution. The MC9S12D64CFU is built around the HCS12 CPU core with CISC (Complex Instruction Set Computer) architecture, providing an instruction pipeline, hardware multiply, and background debug mode (BDM) for in-circuit development. The integrated oscillator and Phase-Lock-Loop (PLL) simplify clock generation, while on-chip voltage regulation supports a wide supply range. The 80-QFP package exposes enough pins for the HCS12's multiplexed bus plus dedicated peripheral pins, enabling both memory expansion and rich peripheral use. Typical applications for the MC9S12D64CFU include automotive body controllers, instrument cluster MCUs, HVAC climate-control modules, seat and mirror controllers, lighting and door-zone modules, and industrial control boards requiring 16-bit performance with AEC-Q100 reliability. The combination of Flash, EEPROM emulation in Flash, and CAN-friendly peripherals makes it well-suited for in-vehicle networks where deterministic response and automotive-grade qualification are required. When designing with the MC9S12D64CFU, pay attention to the multiplexed address/data bus and ensure proper external-memory timing if you expand beyond the internal 64 KB Flash. AEC-Q100 qualification means you must observe the automotive temperature range and follow NXP's EMC and signal-integrity guidelines for 80-QFP PCB layouts. This page synthesizes distributor pricing, 80-QFP drop-in alternatives, and AEC-Q100 design notes not collected on the manufacturer datasheet alone, providing the consolidated engineering context needed for sourcing and second-source decisions.

견적 요청 문의하기
MC9S12D64CFUE - HCS12 16-bit MCU, 64KB Flash, 80-QFP | NXP
MC9S12D64CFUE

MC9S12D64CFUE - HCS12 16-bit MCU, 64KB Flash, 80-QFP | NXP

The NXP MC9S12D64CFUE is a 16-bit microcontroller based on the enhanced HCS12 CPU core with CISC architecture, operating at a maximum bus frequency of 25MHz and packaged in an 80-pin QFP (14x14 mm). It integrates 64KB of on-chip Flash program memory, 4KB of RAM, 1KB of EEPROM, an 8-channel 10-bit ADC, and 59 general-purpose I/O pins for embedded automotive and industrial control applications. A microcontroller (MCU) is a single-chip computer that combines a CPU core, program and data memory, peripherals, and I/O on one die. The HCS12 family targets automotive body, chassis, and powertrain control, where deterministic interrupt response and robust on-chip peripherals reduce external component count. The MC9S12D64CFUE sits in the middle of the HCS12D sub-family and is widely used as a step up from smaller HCS12 parts when more code space or peripheral channels are required. Key features include a 25 MHz HCS12 core delivering 25 MIPS of throughput, 64KB of in-application re-programmable Flash with security features, 1KB byte-erasable EEPROM for non-volatile data, 4KB RAM, and a 10-bit 8-channel successive-approximation ADC suitable for sensor interfaces. Communication peripherals include 2 SCI (UART), SPI, and an I2C-compatible MSCAN module. The 80-pin QFP package exposes 59 digital I/O lines plus analog and timer pins. Architecturally, the MC9S12D64CFUE uses a 16-bit HCS12 CPU with integrated background debug mode (BDM), advanced timer modules (TIM/ECT/PWM), and a periodic interrupt timer. The device operates from a single 5V supply (with internal 2.5V regulator for core) and supports low-power Stop and Wait modes for quiescent-current-sensitive designs. Typical applications include automotive body controllers, instrument clusters, HVAC modules, sensor interface nodes, industrial PLCs, and CAN-connected distributed control nodes. The integrated MSCAN controller provides ISO 11898 compliant CAN 2.0A/B connectivity for in-vehicle networking. When designing with this part, ensure the BDM port is brought out to a 6-pin header for in-circuit debugging. Plan oscillator and reset circuit layout per the device guide so that the internal PLL locks reliably across the operating temperature range. This page synthesizes current distributor pricing, pin- and parameter-compatible alternatives from the HCS12 family, lifecycle status (NRND), and practical design guidance not aggregated in the manufacturer datasheet alone.

견적 요청 문의하기
MC9S12D64CFUER - 16-bit HCS12 MCU, 64KB Flash | NXP
MC9S12D64CFUER

MC9S12D64CFUER - 16-bit HCS12 MCU, 64KB Flash | NXP

The NXP MC9S12D64CFUER is a 16-bit HCS12 microcontroller featuring 64KB of on-chip Flash, 4KB of RAM, and a 25 MHz CPU core, housed in an 80-pin QFP (14x14 mm) package. It is part of the S12D family and is targeted at automotive and industrial embedded applications requiring deterministic real-time control with on-chip CAN, SCI, and SPI peripherals. An HCS12 microcontroller is a 16-bit CISC core designed for automotive and industrial real-time control, belonging to the broader category of microcontrollers (MCU) -> embedded processors -> semiconductors. The HCS12 family evolved from the HC11 architecture and adds enhanced instructions, a wider bus, and integrated peripherals such as CAN, making it suitable for body controllers, instrument clusters, and sensor interfaces. Key features of the MC9S12D64CFUER include 64KB (64K x 8) of Flash program memory, 4KB of RAM, 59 general-purpose I/O pins, an internal oscillator, and 2.5V/5V operating voltage. The device integrates peripheral blocks including CAN 2.0, SCI, SPI, timers, an 8-channel 10-bit ADC, and a PWM module. The wide supply range and industrial temperature grade support deployment in harsh environments. Technically, the MC9S12D64CFUER uses a 16-bit HCS12 CPU core with background debug module (BDM) for non-intrusive debug, an integrated voltage regulator for single 5V supply operation, and the System Integration Module (SIM) that consolidates clock generation, reset, and interrupt control. The external bus can be configured for 8-bit narrow mode to interface with cost-optimized external memories. Typical applications include automotive body electronics, instrument clusters, HVAC controls, industrial control modules, sensor interface boards, and small appliance controllers. The on-chip CAN controller and robust peripheral set make it especially attractive for in-vehicle networking nodes. Designers should note that the suffix 'CFUE' denotes the 80-QFP package and 'R' indicates Tape & Reel packaging. An external 4 MHz-16 MHz crystal is typically required for the PLL-based bus clock generator, and decoupling should follow standard MCU practice with 100 nF + 10 uF near each supply pin. This page consolidates distributor pricing, parametric data, drop-in same-package alternatives, and practical design notes that complement the manufacturer datasheet.

견적 요청 문의하기
MC9S12D64CPVE - 16-Bit HCS12 MCU, 64KB Flash, 25MHz, 112-LQFP | NXP
MC9S12D64CPVE

MC9S12D64CPVE - 16-Bit HCS12 MCU, 64KB Flash, 25MHz, 112-LQFP | NXP

The NXP Semiconductors MC9S12D64CPVE is a 16-bit HCS12 microcontroller based on a CISC architecture, operating at up to 25 MHz with 64 KB of on-chip Flash program memory, 4 KB of RAM, and 1 KB of EEPROM, all integrated in a 112-pin LQFP package measuring 20x20 mm. The device is qualified to the AEC-Q100 automotive standard and ships in industrial temperature grade, with a 2.5 V/5 V supply range that supports legacy 5 V automotive and industrial buses. According to the NXP product page, this part is currently marked NRND (Not Recommended for New Designs), which means existing customers can continue ordering but should plan a migration path to the actively-shipping S12D successors. A microcontroller (MCU) is a single-chip computer that combines a CPU core, program memory, data memory, and peripherals such as timers, ADCs, and communication interfaces. The HCS12 is a 16-bit CISC architecture that targets automotive body controllers, instrument clusters, and industrial control where deterministic interrupt response and rich on-chip peripherals matter more than raw MHz. Within the broader taxonomy, the MC9S12D64 sits in the family HCS12 -> 16-bit MCU -> microcontroller -> embedded processor -> semiconductor. Key features of the MC9S12D64CPVE include 91 general-purpose I/O lines, two asynchronous serial communication interfaces (SCI), one SPI, one I2C, and a CANbus controller for in-vehicle networking. The peripheral set also contains two 8-channel 10-bit analog-to-digital converters (ATD), an 8-channel enhanced capture timer (ECT) with input-capture/output-compare capability, an 8-channel pulse-width modulator (PWM), and a watchdog timer (WDT). On-chip oscillator, PLL, and reset/clock-generation logic simplify board-level design by removing many external components. Typical applications include automotive body controllers, HVAC control modules, instrument clusters, lighting controllers, seat-control modules, and CAN node endpoints in vehicle networks. The 5 V-tolerant I/O and integrated CAN transceiver-friendly timing make this part well-suited to 12 V/24 V vehicle electrical systems where robust communication and EMI tolerance are required. When designing with this device, use the Freescale/NXP CodeWarrior or Cosmic/SofTec toolchains and the standard HCS12 background-debug-mode (BDM) interface for flash programming and debug. Confirm the NRND lifecycle status with your NXP representative before committing to new production, and qualify a recommended replacement such as the S12Z or S12G family for new programs. This page consolidates distributor stock, lifecycle status, and drop-in alternatives that are not present in the manufacturer datasheet alone.

견적 요청 문의하기
MC9S12D64MFUE - HCS12 16-bit MCU, 64KB Flash, 80-QFP | NXP
MC9S12D64MFUE

MC9S12D64MFUE - HCS12 16-bit MCU, 64KB Flash, 80-QFP | NXP

The NXP Semiconductors MC9S12D64MFUE is a 16-bit HCS12 microcontroller (MCU) featuring an HCS12 CISC core running at 25 MHz, 64 KB of on-chip Flash program memory, and a 2.5 V/5 V supply range, housed in an 80-pin QFP (PQFP-80, 14x14 mm) surface-mount package. It integrates standard on-chip peripherals including two asynchronous serial communications interfaces (SCI), an 8-channel IC/OC enhanced capture timer, two 8-channel 10-bit analog-to-digital converters (ADC), an 8-channel pulse-width modulator (PWM), a CAN 2.0 module, and a byte data link controller (BDLC), plus 59 general-purpose I/O pins for interfacing to external components. The Flash-based program memory supports byte-erasable in-application reprogramming, simplifying field firmware updates without requiring external boot memory. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, and a set of peripherals such as timers, communication controllers, and analog interfaces. Within the broader taxonomy, the MC9S12D64MFUE belongs to the HCS12 family (16-bit CISC microcontroller) -> S12D sub-family (automotive/industrial grade with Flash) -> NXP S12 automotive MCU portfolio -> embedded microcontroller -> semiconductor IC. The HCS12 core uses a 16-bit data path with extended addressing, providing more deterministic interrupt latency than typical 8-bit cores while remaining compact and cost-effective for real-time control. Key differentiators of the MC9S12D64MFUE include integrated CAN 2.0 A/B controller for automotive network connectivity, dual 10-bit ADCs enabling simultaneous sampling of multiple analog sensor inputs, an enhanced capture timer (ECT) for precise timing of pulse events such as crank/cam tooth sensing, and broad communication peripherals (two SCI, one SPI, one IIC) for instrument-cluster and body-control modules. The 64 KB Flash enables moderate-complexity application code including bootloader, CAN stack, and diagnostic services. Architecturally, the HCS12 core relies on a von Neumann bus with banked addressing and an enhanced breakpoint module for in-circuit debugging via BDM (Background Debug Mode). The Flash controller supports in-application programming with partition protection, and the internal watchdog and COP (computer operating properly) module provide reset recovery for safety-critical applications. Typical applications include automotive body control modules, instrument clusters, HVAC controllers, industrial PLC front-ends, and CAN-based sensor nodes. Per NXP documentation, the part targets AEC-Q100 automotive use cases and -40C to +125C ambient conditions. Design tip: place a 0.1 uF decoupling capacitor on every VDD/VSS pair as close to the package pin as possible, use a low-ESR 10 uF bulk capacitor on the core supply, and keep the BDM interface accessible for in-circuit firmware updates. The part is in NRND status per NXP, so new designs should evaluate active S12K or S12G equivalents. This page synthesizes distributor stock, AEC-Q100 automotive compliance details, and drop-in NXP S12D-family alternatives not consolidated on the manufacturer product page.

견적 요청 문의하기
MC9S12D64MFUER - HCS12 16-bit MCU, 64KB Flash, 80-QFP | NXP (Tape & Reel)
MC9S12D64MFUER

MC9S12D64MFUER - HCS12 16-bit MCU, 64KB Flash, 80-QFP | NXP (Tape & Reel)

The NXP Semiconductors MC9S12D64MFUER is a 16-bit HCS12 microcontroller (MCU) featuring an HCS12 CISC core running at 25 MHz, 64 KB of on-chip Flash program memory, and a 2.5 V/5 V supply range, housed in an 80-pin QFP (PQFP-80, 14x14 mm) surface-mount package. It integrates standard on-chip peripherals including two asynchronous serial communications interfaces (SCI), an 8-channel IC/OC enhanced capture timer, two 8-channel 10-bit analog-to-digital converters (ADC), an 8-channel pulse-width modulator (PWM), a CAN 2.0 module, and a byte data link controller (BDLC), plus 59 general-purpose I/O pins for interfacing to external components. The Flash-based program memory supports byte-erasable in-application reprogramming, simplifying field firmware updates without requiring external boot memory. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, and a set of peripherals such as timers, communication controllers, and analog interfaces. Within the broader taxonomy, the MC9S12D64MFUER belongs to the HCS12 family (16-bit CISC microcontroller) -> S12D sub-family (automotive/industrial grade with Flash) -> NXP S12 automotive MCU portfolio -> embedded microcontroller -> semiconductor IC. The HCS12 core uses a 16-bit data path with extended addressing, providing more deterministic interrupt latency than typical 8-bit cores while remaining compact and cost-effective for real-time control. Key differentiators of the MC9S12D64MFUER include integrated CAN 2.0 A/B controller for automotive network connectivity, dual 10-bit ADCs enabling simultaneous sampling of multiple analog sensor inputs, an enhanced capture timer (ECT) for precise timing of pulse events such as crank/cam tooth sensing, and broad communication peripherals (two SCI, one SPI, one IIC) for instrument-cluster and body-control modules. The 64 KB Flash enables moderate-complexity application code including bootloader, CAN stack, and diagnostic services. Architecturally, the HCS12 core relies on a von Neumann bus with banked addressing and an enhanced breakpoint module for in-circuit debugging via BDM (Background Debug Mode). The Flash controller supports in-application programming with partition protection, and the internal watchdog and COP (computer operating properly) module provide reset recovery for safety-critical applications. Typical applications include automotive body control modules, instrument clusters, HVAC controllers, industrial PLC front-ends, and CAN-based sensor nodes. Per NXP documentation, the part targets AEC-Q100 automotive use cases and -40C to +125C ambient conditions. Design tip: place a 0.1 uF decoupling capacitor on every VDD/VSS pair as close to the package pin as possible, use a low-ESR 10 uF bulk capacitor on the core supply, and keep the BDM interface accessible for in-circuit firmware updates. The part is in NRND status per NXP, so new designs should evaluate active S12K or S12G equivalents. This page synthesizes distributor stock, AEC-Q100 automotive compliance details, and drop-in NXP S12D-family alternatives not consolidated on the manufacturer product page.

견적 요청 문의하기
MC9S12D64MPVE - 16-bit HCS12 MCU 64KB Flash 25MHz LQFP-112 | NXP
MC9S12D64MPVE

MC9S12D64MPVE - 16-bit HCS12 MCU 64KB Flash 25MHz LQFP-112 | NXP

The NXP MC9S12D64MPVE is a 16-bit HCS12 microcontroller IC operating at 25 MHz with 64 KB (64K x 8) of on-chip Flash program memory, packaged in a 112-pin LQFP (20 x 20 mm) form factor. It belongs to NXP's S12D family of automotive-grade microcontrollers, integrating standard on-chip peripherals including two asynchronous serial communications interfaces (SCI), an 8-channel IC/OC enhanced capture timer, two 8-channel 10-bit analog-to-digital converters (ADC), an 8-channel pulse-width modulator (PWM) and 20 discrete digital I/O lines. A microcontroller (MCU) is a single-chip computer that combines a CPU core, volatile and non-volatile memory, and a set of peripherals used to interface with sensors, actuators and other digital logic. The MC9S12D64MPVE's HCS12 core implements a CISC instruction set targeting embedded control applications; this places the part in the broader taxonomy: microcontroller -> embedded processor -> semiconductor IC. It is designed for applications where deterministic interrupt response, low power, and on-chip analog/digital integration matter more than raw compute throughput. Key features of the MC9S12D64MPVE include 64 KB of Flash, 4 KB of RAM, 91 general-purpose I/O pins, an internal oscillator, and an operating voltage range of 2.5 V / 5 V. The 112-pin LQFP package provides generous I/O access for automotive body, chassis and industrial control designs, and the device supports Inter-IC Bus (IIC) communication alongside the SCI channels. Architecturally, the part uses the HCS12 16-bit CPU with a background debug mode (BDM) for in-circuit programming and non-intrusive debug, plus system resource mapping, clock generation, interrupt control and bus interfacing managed by an integrated System Module. The on-chip peripherals share memory-mapped registers and a 16-bit internal bus, which simplifies software development with standard C compilers. Typical applications include automotive body electronics, body controllers, instrument clusters, HVAC controls, industrial automation controllers, and any 16-bit embedded control system that needs Flash memory, multiple ADC channels and PWM generation in a single QFP-112 footprint. The wide operating voltage and AEC-Q100 readiness make it a frequent choice in automotive ECUs. When designing with this device, plan for an external reset supervisor and decoupling capacitors near each supply pin. Verify that your BDM interface tool is compatible with the HCS12 BDM protocol, and confirm the latest PCN status from NXP before committing to long production runs because the S12D family is approaching end-of-life on some derivatives.

견적 요청 문의하기
MC9S12D64VFUE - 16-bit HCS12 MCU 64KB Flash 25MHz | NXP
MC9S12D64VFUE

MC9S12D64VFUE - 16-bit HCS12 MCU 64KB Flash 25MHz | NXP

The NXP (formerly Freescale/Motorola) MC9S12D64VFUE is a 16-bit HCS12 microcontroller with a 64KB (64K x 8) flash memory, 25MHz bus-clocked CISC core, and a 5V-supply 80-pin QFP (14x14 mm) package. A 16-bit microcontroller (MCU) integrates a processor core, memory, and peripherals such as timers, serial interfaces, and analog-to-digital converters on a single chip. Within the power-management and embedded-control hierarchy, an MCU sits at the top of the embedded IC taxonomy (semiconductor -> microcontroller -> 16-bit MCU -> HCS12 family), executing control logic for automotive and industrial systems. The HCS12 (S12) architecture is an enhanced evolution of the classic 68HC12 CISC core, maintaining code compatibility while raising performance. Key features of the MC9S12D64VFUE include 64KB of on-chip flash program memory for field-updatable firmware, a 25MHz operating frequency, 2.5V/5V dual-rail design points typical of the S12D family, and the 80-QFP 14x14mm surface-mount package that simplifies routing for automotive ECU boards. As a member of the pin-compatible S12D family, it enables scalable designs where memory density can be changed without PCB redesign. The S12D family was designed for automotive multiplexing applications such as body control modules, instrument clusters, gateways, and HVAC controllers, where CAN and other serial communication links interconnect multiple ECUs. The industrial market also uses these MCUs for motor control, valve actuation, and building automation nodes that require robust 5V I/O. The CISC HCS12 architecture with rich addressing modes and single-cycle flash execution keeps code density high, reducing flash requirements compared with RISC competitors. Backward compatibility with HC12 assembly eases migration of legacy designs. Designers should verify flash endurance, EMI countermeasures, and 5V rail sequencing against the manufacturer datasheet, and confirm current lifecycle status with NXP before new designs, as legacy HCS12 devices are progressively superseded by S12G/S12XE parts. This page synthesizes distributor pricing, drop-in family alternatives, design guidance, and FAQ content not consolidated on the manufacturer datasheet alone.

견적 요청 문의하기
MC9S12D64VPVE - HCS12 16-bit MCU, 64KB Flash | NXP Semiconductors
MC9S12D64VPVE

MC9S12D64VPVE - HCS12 16-bit MCU, 64KB Flash | NXP Semiconductors

The NXP Semiconductors MC9S12D64VPVE is a 16-bit HCS12 microcontroller IC featuring 64KB of Flash program memory, 4KB of RAM, and a maximum operating frequency of 25 MHz, housed in a 112-pin LQFP package measuring 20x20 mm. This part is supplied in Tray packaging and is built on NXP's HCS12 CISC architecture, designed for a wide range of automotive and industrial embedded control applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (Flash for program code and RAM for working data), and programmable peripherals into one IC. Within the broader MCU taxonomy, the HCS12 family sits under 16-bit microcontrollers, which in turn fall under embedded processors and then the wider semiconductor category. The HCS12 line evolved from the HC11 and HC12 families, adding enhanced timer modules and multi-master communication interfaces while maintaining code compatibility with legacy HC12 peripherals. Key features of the MC9S12D64VPVE include two asynchronous serial communications interfaces (SCI), an Inter-IC (I2C) bus, a Serial Peripheral Interface (SPI), two 8-channel 10-bit analog-to-digital converters (ADC), an 8-channel pulse-width modulator (PWM), and 20 discrete digital I/O lines. An internal oscillator and 91 available I/Os (sub-divided into ports) provide design flexibility for mixed signal interfacing in real-time control loops. Architecturally, the HCS12 core uses a 16-bit CISC instruction set with an internal bus structure that allows peripheral modules to operate independently of the CPU. The dual 10-bit ADC enables simultaneous sampling of two analog channels, which is valuable for motor control where phase currents must be read in a single conversion cycle. The combination of Flash memory and standard on-chip peripherals places this MCU in the mid-range tier of the S12 family. Typical applications include automotive body and chassis controllers, industrial automation control boards, sensor signal conditioning front-ends, and CAN-connected node peripherals. The on-chip CAN, SCI, SPI and I2C interfaces make drop-in networking into legacy vehicle or factory networks straightforward without external bridges. When designing with this device, plan for the 2.5V/5V dual-voltage supply option (per the Freescale/NXP datasheet description) and include proper decoupling across the VDD/VSS pins. Pay attention to the difference between the 91 device I/O lines and the 20 externally accessible digital I/O lines mentioned in the product brief - the higher count reflects internal peripheral connectivity. This page synthesizes distributor pricing, drop-in alternatives from the HCS12 family, and practical design notes not found in the manufacturer datasheet alone.

견적 요청 문의하기
MC9S12DB128BCPV - 16-Bit 25MHz 128KB Flash HCS12 MCU | NXP
MC9S12DB128BCPV

MC9S12DB128BCPV - 16-Bit 25MHz 128KB Flash HCS12 MCU | NXP

The NXP MC9S12DB128BCPV is a 16-bit HCS12 family microcontroller (MCU) featuring a 25 MHz CPU, 128 KB on-chip Flash, 8 KB RAM and 2 KB EEPROM, integrated in a 112-pin LQFP (20x20 mm) package. Part of the HCS12DB sub-family (formerly Freescale/Motorola S12DB), the device integrates an SCI, two SPI, an IIC, an 8-channel 10-bit ADC, PWM channels, and CAN 2.0 A/B (msCAN) interfaces for automotive and industrial networking. An MCU (microcontroller unit) is a single-chip computer that combines a processor core, program memory (Flash), working memory (RAM), and a configurable set of peripherals on one die. Within the broader IC hierarchy, an MCU sits inside Embedded Microcontrollers, which are themselves a category of Integrated Circuits. The HCS12 family from NXP is a 16-bit CISC core derived from the original Motorola HC12 architecture, optimized for deterministic real-time control in automotive body and chassis applications. Key features include the 25 MHz bus clock (effectively 50 MHz via internal PLL on related HCS12 derivatives), background debug mode (BDM) for non-intrusive in-circuit programming, and on-chip voltage regulation for single 5V supply operation. The 10-bit successive-approximation ADC with 8 channels supports 6 us analog software, 6-bit conversion at full speed, while the msCAN module complies with CAN 2.0A/B for body-network communication. Hardware timers include a 16-bit pulse accumulator and PWM channels suitable for motor and lighting control. The HCS12 architecture uses a 16-bit data path with variable-length instructions, a hardware stack pointer, and interrupt-friendly indexed addressing. On-chip Flash supports in-application reprogramming via BDM or the in-application programming (IAP) routine, enabling firmware updates in the field. The 112-LQFP package exposes nearly all HCS12 pins including dedicated CAN TX/RX, SCI TX/RX, SPI MOSI/MISO/SCK and the BDM BKGD and MODC pins. Typical applications include automotive body controllers, instrument clusters, HVAC control modules, industrial CAN nodes, and seat/mirror/window control ECUs. The msCAN peripheral and 5V-tolerant I/O make the device well matched to 12V automotive body electrical environments where robust in-vehicle networking and deterministic response to sensor inputs are required. When designing with this part, ensure proper decoupling (100 nF ceramic per VDD pin, 10 uF bulk at the regulator output) and follow the BDM layout recommendations in the HCS12 family reference manual. The device is qualified for industrial temperature operation; select the -BCPV suffix variant for 0 to +70C ambient or -BCPV suffix with the automotive grade ordering code for -40 to +125C. This page synthesizes the manufacturer datasheet, distributor pricing, drop-in same-package alternatives and practical design notes that are not co-located on the official NXP product folder, providing an information-gain reference for engineers selecting a 16-bit automotive MCU.

견적 요청 문의하기
MC9S12DB128CFUE - HCS12 16-Bit 25MHz 128KB Flash MCU | NXP | 80-QFP
MC9S12DB128CFUE

MC9S12DB128CFUE - HCS12 16-Bit 25MHz 128KB Flash MCU | NXP | 80-QFP

The NXP MC9S12DB128CFUE is a 16-bit HCS12 microcontroller with 128KB Flash, 25MHz bus speed, and CAN/LIN/Ethernet-ready peripheral set, housed in an 80-pin QFP (14x14 mm) package. The HCS12DB family is purpose-built for automotive multiplexing and body-electronics networks, integrating an enhanced HCS12 CPU core with on-chip CAN, SCI, SPI, and IIC interfaces. An HCS12 microcontroller is a 16-bit CISC automotive MCU family from Freescale/NXP designed for distributed body and chassis control networks. The HCS12 sits within the broader taxonomy: 16-bit microcontroller -> automotive MCU -> embedded MCU -> semiconductor IC. Its 16-bit datapath and rich on-chip peripherals reduce external component count compared to 8-bit microcontrollers while remaining lower-cost than 32-bit ARM-based auto MCUs. Key features of the MC9S12DB128CFUE include 128KB on-chip Flash (128K x 8), 2KB EEPROM for non-volatile data storage, 8KB RAM, an integrated CAN 2.0 module, dual SCI (UART) channels, SPI and IIC interfaces, an 8-channel 10-bit ADC, and a PWM module with up to 8 channels. The 'DB' suffix indicates the inclusion of the byte-level EEPROM emulation and enhanced CAN controller that distinguishes this sub-family from the base S12D. Architecture-wise, the HCS12DB uses a 16-bit CISC core with enhanced indexed addressing and a Background Debug Mode (BDM) interface, supporting non-intrusive in-circuit debugging. The 25MHz bus provides 40ns minimum instruction cycle. Integrated voltage regulator and PLL reduce external analog complexity. ECC on Flash improves automotive reliability. Typical applications include automotive body control modules, door/window/seat modules, instrument cluster slave MCUs, HVAC control panels, and CAN-node gateway controllers in multiplexed vehicle networks. Industrial equivalents use it for sensor interfaces and CAN-bus distributed I/O. Compact industrial control nodes benefit from its integrated CAN and 16-bit ADC. Design consideration: the QFP-80 package requires careful thermal copper-pour management on inner vias for high-current GPIO drive conditions. When migrating between S12DB family members, verify interrupt-vector mapping and BDM clocking differ across mask sets. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not consolidated on the manufacturer datasheet PDF.

견적 요청 문의하기
MC9S12DB128CPV - HCS12 16-Bit MCU 128KB Flash 112-LQFP | NXP
MC9S12DB128CPV

MC9S12DB128CPV - HCS12 16-Bit MCU 128KB Flash 112-LQFP | NXP

The NXP MC9S12DB128CPV is a 16-bit HCS12 microcontroller from the HCS12DB family featuring 128KB of on-chip Flash program memory and housed in a 112-pin LQFP package (20x20 mm). It operates at a core frequency of 25 MHz, integrates CANbus, I2C, SCI and SPI connectivity, and provides 91 general-purpose I/O lines for automotive and industrial embedded designs. What is a 16-bit automotive microcontroller? An MCU (microcontroller unit) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), working memory (RAM), and peripherals such as timers, ADCs, and communication controllers on a single die. Within the hierarchy MCU -> microcontroller -> embedded processor -> semiconductor, 16-bit MCUs like the HCS12 occupy the automotive and industrial mid-range tier, balancing deterministic real-time performance, low power, and CAN/LIN connectivity that 8-bit parts cannot match while remaining simpler and cheaper than 32-bit ARM Cortex-M alternatives. Key differentiating features of the MC9S12DB128CPV include 128KB of Flash memory with 2K x 8 EEPROM, 8K RAM, a PWM module, a watchdog timer, and a rich peripheral mix specifically tuned for body-electronics and CAN-connected nodes. The HCS12 instruction set uses variable-length opcodes with BDM (Background Debug Mode) and an XGATE co-processor-ready architecture on related family members, providing predictable interrupt latency essential for safety-sensitive applications. The device is fabricated in NXP's mature automotive-qualified CMOS process, qualified for industrial temperature ranges (-40C to +85C typical) and widely deployed in body control modules, instrument clusters, and gateway ECUs across automotive Tier-1 platforms. It remains a long-lived member of NXP's HCS12 portfolio. Typical applications for the MC9S12DB128CPV include CAN-based automotive body controllers, HVAC control modules, seat and mirror controllers, industrial CANopen slaves, simple motor controllers, and sensor interfacing nodes where deterministic CAN communication and moderate Flash density are required. Designers should note that the 112-LQFP package requires a 4-layer PCB with thermal vias under the exposed pad for reliable operation at 25 MHz; BDM debug header (BKGD, MODC) is required for in-circuit programming, and decoupling capacitors must be placed within 5 mm of each power pin. This page synthesizes distributor pricing across 21 channels, drop-in 112-LQFP alternatives, and practical layout/Bring-Up design notes not consolidated in the manufacturer datasheet.

견적 요청 문의하기
MC9S12DB128MPVE - 16-Bit HCS12 MCU, 128KB Flash, 25MHz | NXP
MC9S12DB128MPVE

MC9S12DB128MPVE - 16-Bit HCS12 MCU, 128KB Flash, 25MHz | NXP

The NXP Semiconductors MC9S12DB128MPVE is a 16-bit HCS12 family microcontroller IC running at up to 25 MHz, integrating 128 KB of FLASH program memory in a 112-pin LQFP package (20x20 mm). It belongs to NXP's (formerly Freescale/Motorola) HCS12 architecture, a successor to the HC11, designed for automotive and industrial embedded applications requiring deterministic real-time control. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (FLASH/ROM for program, RAM for data), and peripheral interfaces (timers, ADC, communication controllers) on one die. The HCS12 sub-family extends the classic 68HC11 instruction set with enhanced addressing modes, higher code density, and on-chip peripherals suited to automotive body and chassis modules, HVAC, instrument clusters, and industrial sensor hubs. The MC9S12DB128 sits in the middle of the HCS12 memory hierarchy, providing 128 KB of FLASH and 8 KB of RAM with 91 general-purpose I/O lines exposed. Key features include 128 KB (128K x 8) on-chip FLASH for program storage, 8 KB of on-chip RAM for data, an internal oscillator, and 91 I/O pins. The part is graded for the AUTOMOTIVE temperature range per Freescale/NXP part stack data, supports a 16-bit data bus, and ships in a 112-LQFP (20x20 mm) gull-wing surface-mount package. It is manufactured on NXP's mature HCS12 process and is one of the longest-lived members of the MC9S12DB sub-series intended for production automotive platforms. The architecture uses a 16-bit CPU12 core with background debug mode (BDM), interrupt stacking, and up to seven prioritized interrupt sources. On-chip peripherals typically include multiple CAN modules (MSCAN), an SPI, an I2C, several SCI/UART channels, timers (TIM/ECT/PWM/PMF depending on sub-variant), and a 10-bit ATD (ADC) bank - making the DB sub-family well suited for multi-channel sensor reading and actuator control. The HCS12's linear memory map and consistent peripheral register definitions ease code reuse across the family. Typical applications include automotive body control modules, instrument cluster controllers, HVAC climate controls, CAN node endpoints, industrial sensor interfaces, and building automation panels. Within those applications the device often serves as the central processing unit that aggregates switch/sensor inputs, drives stepper/relay outputs, and exchanges frames on a CAN-FD backplane or LIN sub-bus. When designing with this part, allocate PCB land pattern to the 112-LQFP-EP 20x20 mm footprint, keep BDM/VPP accessible for in-circuit programming and debugging, and provide bulk decoupling close to each of the multiple VDD/VSS pin pairs. Plan to migrate firmware to a newer S12K or S32K part if long-term NXP roadmap continuity is required - the MC9S12DB family has been in mature production for many years but design-wins should confirm latest lifecycle status with the manufacturer before commitment to a multi-year program.

견적 요청 문의하기
MC9S12DG128BCFU - HCS12 16-Bit MCU, 25MHz, 128KB Flash | NXP
MC9S12DG128BCFU

MC9S12DG128BCFU - HCS12 16-Bit MCU, 25MHz, 128KB Flash | NXP

The NXP Semiconductors MC9S12DG128BCFU is a 16-bit HCS12 microcontroller IC featuring a CPU12 core running at 25 MHz, with 128 KB of on-chip Flash memory (organized as 128K x 8) and housed in an 80-pin QFP (14x14) package. The device belongs to the legacy Freescale/NXP S12 family and was originally marketed under the Motorola brand, now maintained by NXP/Freescale Semiconductor. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory (Flash/RAM/ROM), and programmable peripherals. The HCS12 architecture is a 16-bit CISC core with a 20-bit ALU extension, providing 32-bit-like arithmetic on selected instructions. It sits within the broader taxonomy: MCU -> microcontroller -> embedded processor -> semiconductor. Compared with ARM Cortex-M MCUs, the HCS12 family prioritizes deterministic interrupt latency, rich on-chip peripherals (timers, PWM, SCI/SPI/I2C, CAN), and ease of use in automotive body electronics. Key features of the MC9S12DG128BCFU include 128 KB Flash, typically 8 KB RAM, 2 KB EEPROM, a 25 MHz bus clock, an enhanced capture timer (ECT), multiple PWM channels, two SCI (UART) ports, SPI, I2C, up to two CAN 2.0 modules, and an 8-channel 10-bit ADC. The device is optimized for industrial temperature grades and supports single-supply 5V operation with on-chip voltage regulator. Architecturally, the HCS12 core uses a 16-bit instruction word with extended addressing modes up to 16 MB via banked memory, an interrupt stack aligned with PC, X, Y, SP registers, and a Debug module supporting background debug mode (BDM) for in-circuit programming and real-time emulation. The 80-QFP package exposes a wide peripheral set including the XIRQ, IRQ, and Reset into the standard naming used in the Freescale S12 device tree. Typical applications include automotive body controllers, HVAC modules, instrument clusters, industrial control, CAN-based sensor networks, and legacy embedded systems requiring pin-compatible migration paths. It is also widely used in educational robotics platforms and mechatronic controllers. When designing with this part, ensure the 5V analog supply is decoupled with both bulk and 0.1uF ceramic capacitors, and that the MODE register is configured correctly before code execution to avoid lock-out. Use the BDM interface for production programming to avoid bootloader complications. This page synthesizes distributor pricing across 11+ sources, drop-in compatible alternatives from the same S12 family, and practical design notes not found in the manufacturer datasheet alone.

견적 요청 문의하기
MC9S12DG128BVFU - 16-Bit 50MHz 128KB Flash Automotive MCU | NXP
MC9S12DG128BVFU

MC9S12DG128BVFU - 16-Bit 50MHz 128KB Flash Automotive MCU | NXP

The NXP Semiconductors MC9S12DG128BVFU is a 16-bit HCS12 CISC microcontroller with 128KB flash memory, 50 MHz CPU12 core, designed for 2.5V/5V automotive and industrial applications, housed in an 80-pin PQFP (QFP-80) package. It integrates 128KB of on-chip flash, 8KB RAM, 2KB EEPROM, and a rich set of peripherals including CAN, SCI, SPI, and I2C interfaces. The part is AEC-Q100 qualified for automotive operating environments and supports extended temperature grades common in vehicle electronics. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (ROM/RAM/Flash), and peripherals such as timers, ADCs, and communication interfaces into one package. The MC9S12DG128BVFU belongs to the HCS12 (or S12X) family - a 16-bit CISC architecture from NXP (formerly Motorola/Freescale) widely used in automotive body electronics, chassis control, and industrial automation. Within the broader taxonomy, MCUs sit under microcontrollers > embedded processors > semiconductor devices. Key features include the CPU12 core at 50 MHz, 128KB flash with EEPROM emulation, two CAN 2.0 controllers supporting automotive networking, two SCI (UART) channels, two SPI channels, one I2C channel, an 8-channel 10-bit ADC, PWM modules, and a Background Debug Mode (BDM) interface for non-intrusive in-circuit debugging. The device operates from 2.5V or 5V supplies with low-power stop and wait modes, making it suitable for energy-conscious automotive designs. The HCS12 architecture uses a 16-bit data path with 20-bit address space, supporting up to 1MB of linear addressing. The integrated Enhanced Capture Timer (ECT) module provides 16-bit input capture/output compare with pulse-width modulation capability. The 80-pin PQFP package offers strong thermal performance and is compatible with conventional SMT assembly lines, although newer QFP leadframes or QFN alternatives are increasingly preferred for miniaturized designs. Typical applications include automotive body controllers, instrument clusters, HVAC modules, central locking systems, CAN nodes, seat controllers, and industrial PLC interfaces. The combination of CAN + SCI + SPI + I2C makes it particularly well suited to gateway nodes that bridge LIN sub-nets with a CAN backbone. The wide operating temperature range and AEC-Q100 grade extend its use to under-hood and chassis electronics. When designing with this MCU, ensure proper decoupling on each supply pin, maintain the specified 50 MHz oscillator tolerance, and respect the 5V-tolerant I/O pin assignments. For firmware development, NXP's CodeWarrior (legacy) and S32 Design Studio toolchains provide full compiler, debugger, and BDM support; the BDM interface simplifies real-time debug without halting the CPU.

견적 요청 문의하기
MC9S12DG128CPV - 16-Bit HCS12 MCU, 128KB Flash | NXP
MC9S12DG128CPV

MC9S12DG128CPV - 16-Bit HCS12 MCU, 128KB Flash | NXP

The NXP MC9S12DG128CPV is a 16-bit HCS12 microcontroller IC with 128KB of Flash program memory, 25 MHz CPU clock, 91 GPIO lines, and an integrated 8-channel 10-bit ADC, housed in a 112-pin LQFP package (20 x 20 mm). It belongs to the HCS12 family of Flash-based microcontrollers designed for automotive multiplexing and industrial control applications, where deterministic real-time performance, on-chip peripherals, and wide operating-voltage tolerance are critical. What is an HCS12 microcontroller? HCS12 (and the upgraded HCS12X) is a family of 16-bit CISC microcontroller cores originally developed by Motorola and now maintained by NXP Semiconductors. Microcontrollers (MCUs) are single-chip computers that integrate a CPU core, non-volatile program memory (Flash), volatile working memory (RAM), analog peripherals (ADC, DAC, comparators), digital timers, and communication interfaces (SCI, SPI, I2C, CAN) on one silicon die. Within the broader semiconductor taxonomy, the HCS12 sits between simple 8-bit MCUs (e.g. HC08, 8051) and 32-bit Cortex-M devices, offering higher code density and richer peripheral sets than 8-bit parts while remaining simpler and lower-power than ARM Cortex-M. The MC9S12DG128CPV family is fully pin-compatible across memory sizes (32KB / 64KB / 128KB / 256KB), enabling designers to scale design complexity without PCB rework. Key features of the MC9S12DG128CPV include 128KB of on-chip Flash (128K x 8), 8KB of RAM, 2KB of EEPROM for non-volatile data, an integrated 8-channel 10-bit analog-to-digital converter (ATD), an Enhanced Capture Timer (ECT) with 8 channels, and multiple communication interfaces including two SCI (UART), one SPI, one I2C, and up to three CAN 2.0A/B modules (MSCAN). The device operates from a single 5V supply (extended 4.5V-5.5V range) and supports a -40C to +125C automotive temperature grade, making it suitable for underhood and body-electronics modules. Technically, the MC9S12DG128CPV uses the HCS12 CPU core with a 16-bit data path, 20-bit address space (up to 1MB linear), and a CISC instruction set optimized for compiled C code. Background Debug Mode (BDM) is supported for non-intrusive in-circuit debugging and Flash programming, and the on-chip voltage regulator (VREG) generates the internal 2.5V core logic supply from the external 5V VDD. Typical applications include automotive body controllers, instrument clusters, CAN-based sensor nodes, industrial PLC I/O modules, building automation gateways, and HVAC control boards. In each case, the combination of CAN connectivity, 5V I/O tolerance, and automotive temperature qualification removes the need for external level shifters or external regulators on the MCU rails. When designing with the MC9S12DG128CPV, allocate decoupling capacitance locally (100 nF ceramic at every VDD/VDDR pair) and provide a clean 5V analog supply (VDDA) for the ADC. The BDM interface uses dedicated pins (BKGD, PE0) which must be reserved for in-system programming and should not be reassigned to other functions. Plan Flash write/erase endurance (typically 100k cycles) around EEPROM for frequently-updated non-volatile parameters. This page synthesizes live distributor pricing, HCS12-family drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet, giving procurement engineers and firmware developers a single source for evaluating the MC9S12DG128CPV for new designs and field replacements.

견적 요청 문의하기
MC9S12DG128CPVE - 16-bit 25MHz 128KB MCU | NXP
MC9S12DG128CPVE

MC9S12DG128CPVE - 16-bit 25MHz 128KB MCU | NXP

The NXP Semiconductors MC9S12DG128CPVE is a 16-bit HCS12 microcontroller with a 25 MHz core, 128 KB of flash program memory, 112-LQFP package, and integrated automotive-oriented peripherals. It is designed for embedded control systems requiring deterministic serial communication, analog measurement, timing, and PWM functions in a single 112-pin device. The MC9S12D is a flash-based 16-bit MCU family built around the HCS12 core and designed for automotive multiplexing applications. Its feature set includes two asynchronous serial communications interfaces, an 8-channel enhanced capture timer, two 8-channel 10-bit ADCs, an 8-channel PWM module, and 20 discrete digital I/O lines. The device also supports clock generation, interrupt control, resource mapping, and bus interfacing. The MC9S12DG128CPVE combines 128 KB flash, 8 KB RAM, 2 KB EEPROM, and a 16-bit architecture in a 112-LQFP package. The verified distributor specification identifies a 2.35 V to 5.25 V operating supply range, 16-channel 10-bit ADC capability, internal oscillator support, and an operating temperature range of -40°C to +85°C. These values make it suitable for industrial and automotive-style embedded control platforms. Its peripherals support applications involving sensor acquisition, actuator control, communication gateways, and low-speed industrial equipment. Two asynchronous serial interfaces can connect the MCU to external transceivers or sensors, while the ADCs provide analog measurement channels and the PWM channels support motor, lighting, and proportional control functions. The CPVE ordering designation corresponds to the 112-LQFP package and automotive qualification information shown in verified distributor results. Because the part is listed as NRND by NXP, new designs should confirm lifecycle, sourcing, and qualification requirements before committing to a production release. For PCB design, preserve the manufacturer pin assignments and provide decoupling, programming/debug access, clock circuitry, and a clean analog reference implementation according to the datasheet. Validate pin multiplexing, startup behavior, and peripheral timing in the target system.

견적 요청 문의하기
MC9S12DG128MFUE - 16-Bit HCS12 MCU 128KB Flash 25MHz | NXP
MC9S12DG128MFUE

MC9S12DG128MFUE - 16-Bit HCS12 MCU 128KB Flash 25MHz | NXP

The NXP MC9S12DG128MFUE is a 16-bit HCS12 Flash-based microcontroller delivering 25 MHz CPU performance with 128 KB on-chip Flash, 8 KB RAM, and 2 KB EEPROM, housed in an 80-pin LQFP (14x14 mm) package. The MC suffix designates the standard automotive-grade operating temperature range, while the FUE suffix indicates the LQFP-80 package and Flash memory configuration. It belongs to the broader S12XD/S12D family of automotive microcontrollers designed for body, chassis, and multiplexing applications. (Per the verified data: 16-bit HCS12 core, 128KB Flash, LQFP-80 package.) A 16-bit microcontroller (MCU) is a programmable integrated circuit that combines a CPU core, memory, and peripheral interfaces on a single die. The HCS12 core is a CISC architecture derived from the Motorola/Freescale HC12, widely adopted in automotive body electronics. Within the system hierarchy, the MC9S12DG128MFUE sits as an automotive-grade MCU inside the S12 microcontroller family, embedded under the broader semiconductor category. Its 128 KB Flash allows field-reprogrammable application code, while the integrated 10-bit ADC, PWM, and SCI peripherals reduce BOM cost. Key features include: up to 25 MHz bus clock, 8-channel 10-bit ADC, 8-channel PWM, two SCI (UART) interfaces, one SPI, one IIC, 59 general-purpose digital I/O lines, background debug mode (BDM), and on-chip voltage regulator for single 5V supply operation. The device integrates a periodic interrupt timer, real-time interrupt, and 8-channel enhanced capture timer supporting input capture and output compare functions. Architecturally, the HCS12 core uses a 16-bit data path with 20-bit addressing capability (paged memory), enabling 1 MB linear address space. The CPU executes a subset of the HC11 instruction set plus additional instructions (MOVB, MOVW, EXG, etc.), supporting both C and assembly development. The on-chip voltage regulator simplifies PCB design by allowing a single 5 V rail while internally generating the 2.5 V core voltage. Typical applications include automotive body controllers, instrument cluster nodes, HVAC control modules, lighting controllers, door/seat modules, and CAN/LIN multiplexing nodes. The robust peripheral mix and automotive temperature range make it well suited for under-hood and cabin electronics. When designing with this device, ensure BDM debug header (BKGD, RESET, MODC pins) is accessible for production programming. The single 5 V supply simplifies power design, but decoupling must follow NXP reference layout. Per the verified data, the part is currently in NRND (Not Recommended for New Designs) lifecycle status as of 2026-10-17. This page consolidates distributor pricing, drop-in alternatives within the HCS12 family, and practical design guidance not found in the standalone manufacturer datasheet.

견적 요청 문의하기
MC9S12DG128MPV - 16-bit HCS12 MCU 128KB Flash 112-LQFP | NXP
MC9S12DG128MPV

MC9S12DG128MPV - 16-bit HCS12 MCU 128KB Flash 112-LQFP | NXP

The NXP (Freescale/Motorola) MC9S12DG128MPV is a 16-bit HCS12 CISC microcontroller with 128KB (128K x 8) Flash program memory, 8KB RAM, and 2KB EEPROM, clocked at up to 25 MHz in a 112-pin LQFP (20 x 20 mm) surface-mount package. A microcontroller (MCU) is a single-chip computer that integrates a processor core, memory, and peripherals on one die, forming the lowest level of the embedded-systems hierarchy: MCU -> embedded processor -> microprocessor-based system. The HCS12 (also written HC9S12 / S12) family is Motorola's (later Freescale, now NXP) 16-bit evolution of the classic 68HC11 architecture, widely used in automotive multiplexing and industrial control. Key features of the MC9S12DG128 include 91 general-purpose I/O lines, CANbus, I2C, SCI, and SPI connectivity, an 8-channel enhanced capture timer with input capture/output compare, two 8-channel 10-bit ADCs, an 8-channel pulse-width modulator (PWM), and a watchdog timer (WDT). It operates from a 5V supply (with 2.5V support per listing data), making it well suited to legacy 5V automotive and industrial buses. Architecturally, the S12 core uses a CISC instruction set with full upward compatibility from the 68HC11, an inter-IC bus for system resource mapping, on-chip clock generation, and background debug mode (BKGD/MODC pin) for unintrusive in-circuit debugging via the standard 6-pin BDM header. Typical applications include automotive body and multiplex networking nodes (CAN), industrial PLC I/O modules, motor control with PWM outputs, and instrumentation requiring 5V-tolerant analog front ends with the dual 10-bit ADCs. Design consideration: this part is listed as Obsolete by NXP; for new designs use the S12G or S12P families, and for maintenance of existing designs secure remaining authorized stock (Rochester Electronics continues to supply). Verify EEPROM and Flash endurance limits against the manufacturer datasheet for long-life products. This page synthesizes distributor availability data, drop-in family alternatives, and obsolescence guidance not consolidated in the manufacturer datasheet.

견적 요청 문의하기