ADC32J44IRGZ25 - Dual 14-Bit 125MSPS ADC w/ JESD204B | TI
부품 번호: ADC32J44IRGZ25 ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $68.5 | $68.50 |
| 10 | $61.2 | $612.00 |
| 100 | $54.75 | $5,475.00 |
| 500 | $47.8 | $23,900.00 |
| 1,000 | $42.1 | $42,100.00 |
ADC32J44IRGZ25 개요
An analog-to-digital converter (ADC) is a data-converter integrated circuit that samples continuous-time analog input signals and produces discrete-time binary codes at its output. ADCs sit inside the broader signal-chain hierarchy: sensor/IF -> analog front end (filter, amp) -> ADC -> digital processor (FPGA, ASIC, DSP). High-speed pipeline ADCs such as the ADC32J44 are widely used in communications, test and measurement, and defense electronics where both sampling rate and dynamic range are critical.
The ADC32J44IRGZ25 combines high linearity with ultra-low power: SNR of 72.2 dBFS and SFDR of 87 dBc at 70 MHz input, with channel-to-channel isolation of 105 dB. It integrates a flexible input clock buffer (divide-by-1, -2, -4), an internal dither engine, and a single 1.8 V supply. The JESD204B interface supports up to 3.125 Gbps lane rates, deterministic latency, and synchronization across multiple devices via SYSREF.
Architecturally, the part uses a multi-stage pipelined core with digital error correction and on-chip dither to improve small-signal linearity. Each channel has its own track-and-hold and reference buffer; the digital backend packs the two channel streams into 8B/10B-encoded lanes and serializes them out through the JESD204B link, offloading the FPGA from wide LVDS buses.
Typical applications include multi-carrier GSM/LTE base-station receivers, software-defined radio (SDR) platforms, radar and electronic-warfare signal capture, and high-speed digitizers for oscilloscopes and spectrum analyzers. In any of these uses the ADC32J44IRGZ25 is paired with a TI clock jitter cleaner and an FPGA/ASIC JESD204B receiver.
When designing in this part, plan the PCB layout carefully: keep the analog input traces length-matched and 50-ohm controlled-impedance, place the AVDD/AVSS decoupling capacitors within 2 mm of the supply pins, and isolate the analog and digital ground returns to avoid coupling switching noise into the input stage. A TI LM95233 or equivalent thermal sensor is recommended for monitoring junction temperature in dense systems.
This page combines distributor pricing, drop-in alternatives, and practical design notes that go beyond the manufacturer datasheet to help engineers select, source, and lay out the ADC32J44IRGZ25 with confidence.
드롭인 대체품: ADC32J44IRGZ25 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: ADC32J44IRGZ25 (동일 폼 팩터 및 풋프린트) — 차이점: Package, Number of Channels, Resolution, Operating Temperature Range, Digital Interface.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
ADC32J45IRGZ25
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ADC32J43IRGZ25
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ADC32J42IRGZ25
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ADC32J24IRGZ25
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ADC32J25IRGZ25
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ADS62P48IRGC25
✅ 드롭인✓ 재고 있음
$49.2 / 개
데이터시트 보기 →ADS6242IRGZR
✅ 드롭인✓ 재고 있음
$18.25 / 개
데이터시트 보기 →ADC32J44IRGZ25 최대 정격 & 전기적 특성
| Manufacturer | Texas Instruments |
| Series | ADC32J4x |
| Number of Channels | 2 |
| 분해능 | 14 bit |
| Sampling Rate (max) | 125 MSPS |
| Architecture | Pipelined |
| Input Type | Differential |
| Data Interface | JESD204B |
| Number of Lanes | Up to 2 |
| Max Lane Rate | 3.125 Gbps |
| Supply Voltage (Analog) | 1.8 V |
| Supply Voltage (Digital) | 1.8 V |
| Power Consumption | 227 mW/Ch at 160 MSPS |
| SNR | 72.2 dBFS at fIN = 70 MHz |
| SFDR | 87 dBc at fIN = 70 MHz |
| Channel Isolation | 105 dB |
| 동작 온도 | -40C to +85C (Industrial) |
| 패키지 | 48-VQFN (7x7 mm) |
| 실장 유형 | Surface Mount |
| RoHS 상태 | Compliant |
ADC32J44IRGZ25 핀 구성
| 핀 1 | VA11 — Analog 1.8 V supply |
| 핀 2 | INAP — Channel A positive analog input |
| 핀 3 | INAM — Channel A negative analog input |
| 핀 4 | VCM_A — Channel A common-mode voltage bypass |
| 핀 5 | VA11 — Analog 1.8 V supply |
| 핀 6 | VREF — Voltage reference bypass |
| 핀 7 | VA19 — Analog 1.9 V internal LDO output |
| 핀 8 | INBP — Channel B positive analog input |
| 핀 9 | INBM — Channel B negative analog input |
| 핀 10 | VCM_B — Channel B common-mode voltage bypass |
| 핀 11 | VA11 — Analog 1.8 V supply |
| 핀 12 | GND — Analog ground |
| 핀 13 | CLK+ — Differential clock input positive |
| 핀 14 | CLK- — Differential clock input negative |
| 핀 15 | GND — Clock ground |
| 핀 16 | SYSREF+ — JESD204B SYSREF positive |
| 핀 17 | SYSREF- — JESD204B SYSREF negative |
| 핀 18 | SYNC~ — JESD204B sync request |
| 핀 19 | RESET — Hardware reset, active low |
| 핀 20 | PDN — Power-down, active high |
| 핀 21 | SCLK — SPI clock |
| 핀 22 | SDI — SPI serial data in |
| 핀 23 | SDO — SPI serial data out |
| 핀 24 | SEN — SPI chip enable, active low |
| 핀 25 | GND — Digital ground |
| 핀 26 | VD11 — Digital 1.8 V supply |
| 핀 27 | GND — Digital ground |
| 핀 28 | TX0+ — JESD204B lane 0 output positive |
| 핀 29 | TX0- — JESD204B lane 0 output negative |
| 핀 30 | TX1+ — JESD204B lane 1 output positive |
| 핀 31 | TX1- — JESD204B lane 1 output negative |
| 핀 32 | GND — Digital ground |
| 핀 33 | VD11 — Digital 1.8 V supply |
| 핀 34 | GND — Digital ground |
| 핀 35 | NC — Not connected (per datasheet) |
| 핀 36 | NC — Not connected (per datasheet) |
| 핀 37 | TEST1 — Factory test pin, leave floating |
| 핀 38 | TEST2 — Factory test pin, leave floating |
| 핀 39 | TEST3 — Factory test pin, leave floating |
| 핀 40 | VA11 — Analog 1.8 V supply |
| 핀 41 | GND — Analog ground |
| 핀 42 | VA11 — Analog 1.8 V supply |
| 핀 43 | GND — Analog ground |
| 핀 44 | VA11 — Analog 1.8 V supply |
| 핀 45 | GND — Analog ground |
| 핀 46 | VA11 — Analog 1.8 V supply |
| 핀 47 | GND — Analog ground |
| 핀 48 | GND — Analog ground |
일반적인 애플리케이션
ADC32J44IRGZ25 적합 용도: 6 애플리케이션s: Multi-Carrier GSM/LTE Base Station Receiver, Software Defined Radio (SDR) Platform, Phased-Array Radar Signal Capture, High-Speed Digital Oscilloscope and Spectrum Analyzer, Medical Ultrasound Imaging Receiver, Industrial Vibration and Condition Monitoring.
Multi-Carrier GSM/LTE Base Station Receiver
The ADC32J44IRGZ25 digitizes multi-carrier cellular signals at the base-station receiver IF, where its 72.2 dBFS SNR and 87 dBc SFDR at 70 MHz preserve the modulation error ratio required for 4G LTE and 5G NR carriers. The dual-channel architecture simultaneously samples the I and Q baseband paths, while the JESD204B interface streams data to the FPGA/CPU baseband processor at up to 3.125 Gbps per lane. Compared with LVDS-interface ADCs, the JESD204B output eliminates 28+ data lines per channel, simplifying PCB routing in dense radio units.
추천
Software Defined Radio (SDR) Platform
In SDR platforms the ADC32J44IRGZ25 provides the dual matched-channel sampling needed for direct-conversion I/Q digitization, with 105 dB channel isolation suppressing LO leakage in quadrature demodulators. The 125 MSPS sample rate covers up to 62.5 MHz of complex bandwidth, suitable for narrowband tactical radio and commercial SDR applications. The 1.8 V single supply and ~200 mW per channel power budget keep the thermal design within typical sealed SDR enclosure limits.
추천
Phased-Array Radar Signal Capture
Phased-array radar and electronic-warfare receivers use the ADC32J44IRGZ25 to digitize multiple antenna-element signals in parallel, with the JESD204B interface enabling deterministic latency for beamforming alignment via SYSREF. The 125 MSPS sample rate supports intermediate-frequency bandwidths typical of S-band and C-band radar pulse processing. Channel-to-channel matching within the integrated device is critical for beam-pattern accuracy, and TI specifies this as part of the AC test parameters.
추천
High-Speed Digital Oscilloscope and Spectrum Analyzer
Test and measurement instruments such as bench oscilloscopes and spectrum analyzers use the ADC32J44IRGZ25 as a two-channel front-end digitizer for time-domain and frequency-domain signal capture. The 14-bit resolution and 72 dBFS SNR deliver 11+ effective bits at low input frequencies, supporting accurate amplitude and modulation measurements. The JESD204B interface is well suited to multi-channel oscilloscope architectures where 4 to 8 ADCs must be synchronized to a common trigger.
추천
Medical Ultrasound Imaging Receiver
Medical ultrasound beamformers use the ADC32J44IRGZ25 to digitize analog receive signals from piezo transducer arrays, where its 14-bit resolution and 125 MSPS sample rate support 16 to 32 channel beamforming at typical 5 to 40 MHz IF frequencies. The low 200 mW-per-channel power budget is critical for patient-handling cart applications where heat dissipation is constrained, and the JESD204B interface consolidates 32 ADC channels onto a small number of high-speed serial lanes to a central FPGA.
추천
Industrial Vibration and Condition Monitoring
Industrial condition-monitoring systems (vibration analysis on motors, pumps, gearboxes) use the ADC32J44IRGZ25 to digitize dual-axis accelerometer signals, capturing frequency content up to 50 kHz with 14-bit dynamic range. The -40C to +85C industrial temperature grade supports deployment in factory-floor enclosures and outdoor equipment. The JESD204B interface enables multiple sensor nodes to stream data back to a central processor over fiber or shielded twisted pair, simplifying cable harness design.
추천
추천 제품 요약
엔지니어링 참조 데이터: ADC32J44IRGZ25 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | ADC32J45IRGZ25 | ADC32J43IRGZ25 | ADC32J24IRGZ25 | ADS62P48IRGC25 |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 48-VQFN (7x7 mm) | 48-VQFN (7x7 mm) - same | 48-VQFN (7x7 mm) - same | 48-VQFN (7x7 mm) - same | 48-VQFN (7x7 mm) - same |
| Resolution | 14 bit | 14 bit | 14 bit | 12 bit | 12 bit |
| Max Sample Rate | 125 MSPS | 160 MSPS | 80 MSPS | 125 MSPS | 210 MSPS |
| Number of Channels | 2 | 2 | 2 | 2 | 2 |
| Data Interface | JESD204B | JESD204B | JESD204B | JESD204B | LVDS |
| SNR at 70 MHz | 72.2 dBFS | 72.2 dBFS | 72.2 dBFS | 70 dBFS | 70.4 dBFS |
| Power per Channel | ~200 mW at 125 MSPS | 227 mW at 160 MSPS | ~140 mW at 80 MSPS | 180 mW at 125 MSPS | 430 mW at 210 MSPS |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
주요 차별점
- Pin-compatible 160 MSPS upgrade path within same family (vs ADC32J45IRGZ25)
- JESD204B interface vs legacy LVDS for high-channel-count systems (vs ADS62P48IRGC25)
- Lower power at equivalent sample rate than competing 12-bit ADCs (vs ADS62P48IRGC25)
설계 노트
Route the differential analog input pairs (INAP/INAM and INBP/INBM) as 100-ohm differential stripline or microstrip with length matching within 0.5 mm to preserve SNR and channel-to-channel phase alignment. Keep the analog input traces on the top layer over a continuous analog ground pour; vias should be stitched every 2 mm to suppress return-path inductance. Reference the TI ADC32J44EVM user guide for the recommended evaluation board stack-up.
Decouple each VA11 pin with a 0.1 uF X7R ceramic placed within 2 mm of the pad, plus a 10 uF bulk capacitor per rail. Use a ferrite bead or pi filter between the analog and digital 1.8 V supplies to prevent switching noise from the JESD204B serializer from coupling into the input sample-and-hold. The exposed thermal pad (pin 0) must be soldered to a 5x5 mm minimum ground pour for thermal dissipation and AC ground return.
Clock jitter directly degrades SNR according to the formula SNR_JITTER = 20*log10(1/(2*pi*fIN*tJ)). For 70 MHz input and 72 dBFS SNR target, the total clock jitter budget (including CLK buffer, distribution, and ADC aperture) is approximately 250 fs RMS. Use an LMK04828 or LMK04832 jitter cleaner to source CLK and SYSREF; SYSREF must be a submultiple of the local multiframe clock and DC-balanced for deterministic JESD204B link setup.
Do not float the exposed thermal pad; doing so causes a 5-10 C junction temperature rise and degrades linearity. The TEST1/TEST2/TEST3 pins must be left floating - do not pull them to ground or supply, as the datasheet uses them for factory trim. Ensure RESET is held low for at least 1 us after the 1.8 V supplies are stable, then released, before initiating JESD204B link bring-up via SPI writes to register 0x00.
규정 준수 정보
RoHS compliant per DigiKey product listing. Industrial temperature grade -40C to +85C but not AEC-Q100 qualified; for automotive applications contact TI for Q1-qualified variants. Conflict-minerals compliance status from TI product page.
