CD4029BPW - 4-Bit CMOS Up/Down Counter | Texas Instruments
부품 번호: CD4029BPW ✓ 활성CD4029BPW 개요
A counter IC is a member of the broader digital logic hierarchy that includes counters, dividers, registers, and shift registers. The CD4029B family adds reversible counting to that category: a clock pulse advances or reverses the four-bit state, while preset and reset controls allow the counter to be loaded or cleared. Because the device supports both binary and decade modes, one counter can implement modulo-16 binary sequences or decade sequences for timing and sequencing applications.
Principal features include four parallel counting outputs, selectable up or down operation, binary or decade counting, preset control, carry output, and positive-edge clocking. Its operating supply range of 3 V to 18 V allows operation across common low-voltage and higher-voltage CMOS logic systems. The listed maximum clock frequency of 11 MHz establishes the operating point for designs requiring medium-speed counting rather than high-frequency timing-chain performance.
The CD4029B is implemented as a CMOS logic integrated circuit, allowing operation from a single 3 V to 18 V supply. Its 16-pin TSSOP package supports compact surface-mount assemblies, while the four outputs provide direct state visibility. Designers should account for propagation delay, setup and hold requirements, and the permitted clock transition times when evaluating the maximum operating frequency in a particular system.
Typical uses include industrial step and cycle counters, programmable sequence controllers, digital timing modules, phase and position counters, and control systems requiring bidirectional counting. The decade mode can simplify decade-oriented display or sequencing systems, while binary mode supports modulo-16 state machines. The carry output can be monitored by adjacent logic to indicate a count boundary.
For PCB implementation, place the clock and control inputs away from high-current switching paths, and use a defined common ground reference. CMOS inputs should not be left floating, and unused inputs should be tied to a defined valid logic level. Power-supply bypassing and signal-integrity review should follow the layout guidance in the manufacturer datasheet.
This page organizes the CD4029BPW function, package information, design considerations, commercial information, and validated replacement analysis into one engineering-focused reference. It also distinguishes exact drop-in options from variants that differ in package, pinout, or qualification, helping designers avoid substitution errors before schematic release.
드롭인 대체품: CD4029BPW — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: CD4029BPW (동일 폼 팩터 및 풋프린트) — 차이점: Counter Type, Counting Direction, Logic Family, Mounting Type, Number of Outputs.
이 제품에는 사용 가능한 드롭인 대체품이 없습니다.
대체품 요청CD4029BPW 최대 정격 & 전기적 특성
| Counter Type | Binary/decade presettable up/down counter |
| Number of Bits | 4 bits |
| Number of Elements | 1 element |
| Supply Voltage Range | 3 V to 18 V |
| 최대 클록 주파수 | 11 MHz |
| Clock Edge | Positive edge |
| Counting Direction | Up or down |
| Counting Modes | Binary or decade |
| 출력 수 | 4 outputs |
| Preset Function | Asynchronous preset |
| Package Type | 16-pin TSSOP |
| Package Width | 4.40 mm |
| Package Body Width | 0.173 mm |
| 실장 유형 | Surface mount |
| Logic Family | 4000B CMOS series |
| RoHS Compliance | Unknown |
| REACH Compliance | Unknown |
| Automotive Qualification | Not applicable |
CD4029BPW 0.173 mm 핀 구성 가이드
CD4029BPW(0.173 mm 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: CD4029BPW.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
CD4029BPW 적합 용도: 6 애플리케이션s: Industrial Sequence Control, Programmable Digital Timer, Position and Step Counter, Digital Phase Counter, Industrial Test and Measurement, Automation and Robotics Control.
Industrial Sequence Control
The CD4029BPW fits industrial sequence-control blocks because it combines 4-bit counting, selectable up or down direction, binary or decade modes, and a carry output within one 16-pin TSSOP device. A controller can load a preset state, advance on each positive clock edge, and use the carry output to mark a count boundary. Its 3 V to 18 V operating range supports multiple logic-supply levels, while the 11 MHz maximum clock frequency accommodates medium-speed machine-event counting. Design the timing budget around propagation delay and ensure that preset or reset timing conforms to the manufacturer datasheet.
추천
Programmable Digital Timer
CD4029BPW can form the counting core of a programmable timer or elapsed-event counter by loading a preset value and observing the four parallel outputs as the state advances. Binary mode supports a modulo-16 event count, while decade mode is useful when the application is organized around groups of ten. Reversible counting can support repeat or retrace functions. The 11 MHz clock capability provides substantial margin for moderate-rate timing references, but the final maximum frequency must account for output propagation delay and the external logic driving the clock.
추천
Position and Step Counter
A bidirectional counter such as the CD4029BPW is useful in position and step-counting systems because the count-direction input can be changed without changing the clock architecture. The four outputs expose the current count for comparison, decoding, or display-control logic. Positive-edge clocking supports a clean reference-to-counter arrangement in incremental encoder and actuator-position systems. The 3 V to 18 V supply range accommodates common digital control voltages, while designers should use conservative clock rates if mechanical switch bounce can create multiple edges.
추천
Digital Phase Counter
The CD4029BPW can count phase or index events when the system must distinguish forward and reverse motion. Selectable binary counting retains all four state bits, and the carry output provides a convenient indication of an overflow or count-boundary event. This arrangement is suitable for motor-control feedback, rotary mechanisms, and repetitive actuator indexing. The counter's 11 MHz maximum clock frequency is well above typical low-rate position-event frequencies, but input conditioning must suppress bounce and ensure clean positive edges.
추천
Industrial Test and Measurement
CD4029BPW can serve as a repeatable event-counting element in test and measurement fixtures where pulses must be tallied in a known direction. A preset establishes the starting state, the clock input counts qualified events, and the parallel outputs can be read by a controller. The logic family operates from 3 V to 18 V, which can simplify interface design around different test systems. Instrument builders should verify settling time, clock jitter tolerance, input thresholds, and timing margins at the intended 3 V or higher operating voltage.
추천
Automation and Robotics Control
The CD4029BPW is appropriate for compact automation logic that tracks recurring steps, cycles, or indexed positions. Its TSSOP package preserves board area, and the four count outputs can feed comparison logic or a programmable I/O interface. Selecting decade mode simplifies ten-step cycle organization, while binary mode supports arbitrary four-bit states. The 3 V to 18 V supply range integrates with common embedded-control rails, and the carry output can trigger a machine action at a defined count. Validate control latency and electrical isolation at every actuator interface.
추천
추천 제품 요약
엔지니어링 참조 데이터: CD4029BPW — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 |
|---|---|
| Package | 16-pin TSSOP |
| Brand | Texas Instruments |
| Counter Type | Presettable binary/decade up/down counter |
| Number of Bits | 4 bits |
| Supply Voltage Range | 3 V to 18 V |
| Maximum Clock Frequency | 11 MHz |
| Counting Direction | Up or down |
| Clock Edge | Positive edge |
| Logic Family | 4000B CMOS series |
설계 노트
Route the clock as a short trace from its source and provide a clean return path beneath the device. Positive-edge counting means multiple transitions caused by switch bounce or noisy shielding can increment the count more than once. Use Schmitt-trigger conditioning where an external mechanical or slow-transition signal drives the clock, and keep the preset, reset, and count-direction traces away from switching-node and high-current paths.
Operate the CD4029BPW only within its documented 3 V to 18 V supply range, and confirm that every external signal remains within the valid input thresholds at the selected supply voltage. Place the supply bypass capacitor close to the device's supply and ground connections, with a short, low-impedance ground return. Raise the clock rate only after checking propagation-delay timing and ensuring the source meets the permitted clock transition-time requirement.
Do not leave control inputs floating or assume that preset and reset have identical timing behavior. Verify the required setup and hold relationships in the Texas Instruments CD4029B datasheet before issuing a preset coincident with a clock edge. Also confirm whether the required sequence is binary or decade; an incorrect mode-control level changes the modulus and can make a repeating sequence appear to skip states.
규정 준수 정보
The verified product information identifies the CD4029B as a 4000B-series CMOS logic IC but does not state RoHS, REACH, halogen-free, lead-free, conflict-minerals, or automotive qualification status.