RTAX250SL-CG624B - 250K Rad-Tolerant FPGA 624-CCGA | Microchip
부품 번호: RTAX250SL-CG624B ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $4850 | $4,850.00 |
| 10 | $4620 | $46,200.00 |
| 100 | $4380 | $438,000.00 |
| 500 | $4150 | $2,075,000.00 |
| 1,000 | $3950 | $3,950,000.00 |
RTAX250SL-CG624B 개요
A radiation-tolerant FPGA is a field-programmable gate array engineered to survive and operate reliably in the space radiation environment, where energetic particles cause single-event effects (SEEs) and total ionizing dose (TID) degradation. Within the space electronics hierarchy, the RTAX-SL family sits alongside other radiation-hardened/tolerant programmable logic solutions and is based on the commercial Axcelerator architecture from Microsemi (now Microchip Technology).
Key features include true single-chip operation (no external configuration PROM required at power-up thanks to antifuse technology), live-at-power-up behavior, embedded SRAM blocks with built-in FIFO control logic, segmentable clock resources, chip-wide highway routing, and dedicated carry logic for arithmetic. The antifuse interconnect is inherently immune to configuration upsets, a decisive advantage over SRAM-based FPGAs in orbit.
Architecturally, the RTAX-SL is derived from the Axcelerator family, with 0.15 um antifuse technology providing low static power and configuration immutability. The device achieves a maximum combinatorial CLB delay of 0.930 ns, enabling pipelined DSP and telemetry processing at up to 649 MHz.
Typical applications include satellite on-board data handling, spacecraft command and telemetry, payload signal processing, and radiation-exposed avionics where configuration-upset immunity is mandatory.
Design consideration: the CCGA624 package requires controlled-impedance, column-grid-array-capable PCB assembly and X-ray inspection; plan board layout early.
This page synthesizes distributor inventory data, drop-in family alternatives, and practical design guidance not found in the manufacturer datasheet alone.
드롭인 대체품: RTAX250SL-CG624B — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: RTAX250SL-CG624B (동일 폼 팩터 및 풋프린트) — 차이점: Radiation Tolerance, Configuration, Package, Family, Embedded Memory.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
RTAX250SL-1CG624B
✅ 드롭인✓ 재고 있음
가격 문의
데이터시트 보기 →RTAX250SL-CGS624B
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
RTAX250SL-1CGS624B
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
RTAX250S-CG624B
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$2800 / 개
데이터시트 보기 →RTAX250SL-LG624B
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$2380 / 개
데이터시트 보기 →RTAX250SL-CG624B 최대 정격 & 전기적 특성
| Family | RTAX-SL (Radiation-Tolerant FPGA) |
| Equivalent System Gates | 250000 gates |
| Logic Cells / CLBs | 2816 cells |
| 최대 클록 주파수 | 649 MHz |
| Combinatorial Delay (CLB) | 0.930 ns max |
| Process Technology | 0.15 um antifuse |
| Core Supply Voltage | 1.5 V |
| 패키지 | 624-ball CCGA (CG624) |
| 실장 유형 | Surface Mount |
| Configuration Technology | Antifuse (single-chip, live at power-up) |
| Embedded Memory | Embedded SRAM with FIFO control logic |
| Radiation Tolerance | Radiation-tolerant (space-flight grade) |
| Programmability Type | Field Programmable Gate Array (one-time programmable) |
RTAX250SL-CG624B 624-ball ccga (cg624) 핀 구성 가이드
RTAX250SL-CG624B(624-ball ccga (cg624) 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: RTAX250SL-CG624B.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
RTAX250SL-CG624B 적합 용도: 6 애플리케이션s: Satellite On-Board Data Handling, Payload Signal Processing, Command and Telemetry Systems, Radiation-Exposed Avionics, Space Bus Interface and Glue Logic, Earth Observation Instrument Control.
Satellite On-Board Data Handling
The RTAX250SL-CG624B fits spacecraft on-board computer and data-handling units because its antifuse configuration is immune to single-event configuration upsets, eliminating the scrubbing hardware an SRAM FPGA would require. With 250,000 gates and 2816 CLBs organized through chip-wide highway routing, the device implements command decoders, telemetry formatters, and bus interfaces (e.g., MIL-STD-1553, SpaceWire glue logic) in one 1.5 V core device. Live-at-power-up behavior means the OBC logic is functional the instant spacecraft power is applied, supporting autonomous FDIR recovery flows. The embedded SRAM with FIFO control logic buffers housekeeping data streams, while the 649 MHz family timing ceiling leaves ample margin for conventional bus-rate interfaces. Designers should budget the 0.930 ns maximum CLB combinatorial delay when closing timing on high-rate paths and reserve the segmentable clock resources to isolate payload clocking from the data-handling domain.
추천
Payload Signal Processing
In instrument and communications payloads, the RTAX250SL-CG624B implements front-end DSP functions such as decimation filters, FFT pre-processing, framing, and packetization. Dedicated carry logic accelerates adder/accumulator chains, and the 0.15 um process timing (0.930 ns CLB combinatorial delay) supports pipelined arithmetic at high throughput, with a family maximum clock of 649 MHz for the fastest paths. The antifuse fabric contributes no configuration-upset failure mode, a significant advantage for payloads that cannot tolerate controller resets during science acquisition. Embedded SRAM blocks with built-in FIFO control serve as ping-pong buffers between acquisition and downlink chains without external memory. Because the device is one-time programmable, freeze the netlist early and use footprint-compatible prototyping per Microchip's RTAX prototyping application note before committing flight devices. Thermally, space-flight conduction-cooled assemblies should verify power against mission worst-case clock activity rather than family headline numbers.
추천
Command and Telemetry Systems
Spacecraft command and telemetry units benefit from the RTAX250SL-CG624B's deterministic, fixed netlist: once programmed, routing and timing are identical on every flight unit, simplifying verification for mission assurance. The 250K-gate capacity covers frame synchronizers, CRC/hash engines, decoders for uplink command formats, and time-tag distribution logic, while segmentable clocks let designers quarantine the time-critical timing chain from noisier data paths. The 1.5 V core and 0.15 um antifuse process keep static power low - important for telemetry units that remain powered through eclipse and safe-mode. Live-at-power-up operation guarantees the telemetry path is observable during the first milliseconds after switch-on, aiding launch and early-orbit operations. Implement input protection and voting (TMR at the RTL level) for single-event-effect-sensitive registers per the Microchip RTAX-S/SL design guidance, since antifuse immunity covers configuration, not user flip-flops.
추천
Radiation-Exposed Avionics
Launch vehicles, reentry systems, and high-altitude platforms encounter radiation environments where commercial FPGAs upset frequently. The RTAX250SL-CG624B addresses these avionics needs with a radiation-tolerant 0.15 um antifuse fabric that cannot lose its configuration, plus 2816 CLBs of user logic for flight-control glue, sensor interface conditioning, and redundancy management. The 624-ball CCGA package's solder columns provide mechanical compliance for vibration and thermal-cycling environments typical of flight hardware, and ceramic packaging supports the outgassing and workmanship expectations of space avionics programs. Because the device is live at power-up, flight-critical safety functions are available immediately without configuration load delay - a requirement in many ascent-phase architectures. Designers should pair the FPGA with watchdog supervision at system level and apply Microchip's SEE mitigation application notes for user-logic hardening, as antifuse protection applies to the configuration layer only.
추천
Space Bus Interface and Glue Logic
Modern spacecraft integrate mixed-vintage subsystems; the RTAX250SL-CG624B serves as the protocol-bridging fabric between legacy MIL-STD-1553, CAN, UART, and custom serial links and newer payload digital interfaces. With 250,000 gates and chip-wide highway routing, multiple independent bridges fit in a single device, reducing part count on radiation-exposed boards - each removed commercial component is one less SEE risk. The 649 MHz family clock ceiling and 0.930 ns CLB delay easily cover all conventional spacecraft bus rates, so timing closure is dominated by I/O constraints rather than internal logic depth. Embedded SRAM/FIFO blocks provide rate-buffering between asynchronous clock domains without external memories. The 624-ball CCGA footprint provides generous I/O for multi-bus systems. Fix the netlist under formal configuration control so each bridge's timing remains constant across flight lots, and validate I/O standards and drive strength in Microchip Libero constraints before board release.
추천
Earth Observation Instrument Control
Cameras, spectrometers, and scatterometers on Earth-observation satellites need deterministic sequencing, detector-clock generation, and high-rate data formatting - workloads well matched to the RTAX250SL-CG624B's 250K gates, 2816 CLBs, and embedded SRAM FIFOs. The antifuse fabric guarantees the instrument control sequence cannot be corrupted in orbit, protecting irreplaceable acquisition opportunities during imaging passes. The 1.5 V core reduces the FPGA's share of instrument power budgets, and live-at-power-up operation simplifies the instrument's turn-on sequencing. Segmentable clocks let detector clocking, control, and downlink domains run from isolated timing trees. Implement detector bias sequencing and safety interlocks in the FPGA with TMR on safety-critical flags, per Microchip RTAX-S/SL reliability guidance, since user registers - not the antifuse configuration - are the SEE-sensitive elements. Plan the CCGA624 land pattern and X-ray inspection criteria early, as ceramic column arrays dominate the assembly cost of the controller board.
추천
추천 제품 요약
엔지니어링 참조 데이터: RTAX250SL-CG624B — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | RTAX250SL-1CG624B | RTAX250SL-CGS624B | RTAX250SL-1CGS624B | RTAX250S-CG624B | RTAX250SL-LG624B |
|---|---|---|---|---|---|---|
| Package | CCGA-624 (CG624) | CCGA-624 - same | CCGA-624 - same | CCGA-624 - same | CCGA-624 - same | 624-position ceramic - same |
| Brand | Microchip Technology (Actel/Microsemi) | Microchip Technology | Microsemi (Microchip) | Microsemi (Microchip) | Microchip Technology | Microchip Technology |
| Equivalent System Gates | 250,000 | 250,000 | 250,000 | 250,000 | 250,000 | 250,000 |
| Logic Cells / CLBs | 2816 | 2816 | 2816 | 2816 | 2816 | 2816 |
| Maximum Clock Frequency | 649 MHz (family) | 649 MHz (family) | 649 MHz (family) | 649 MHz (family) | 649 MHz (family) | 649 MHz (family) |
| Speed Grade | Standard | -1 (faster) | Standard | -1 (faster) | Standard | Standard |
| Core Supply Voltage | 1.5 V | 1.5 V | 1.5 V | 1.5 V | 1.5 V | 1.5 V |
| Configuration Technology | Antifuse (single-chip, live at power-up) | Antifuse | Antifuse | Antifuse | Antifuse | Antifuse |
주요 차별점
- Configuration-upset immunity from antifuse fabric (vs RTAX250S-CG624B)
- Higher performance without redesign (vs RTAX250SL-CGS624B)
- Lead-free assembly option on the same footprint (vs RTAX250SL-CG624B (non-S))
- Trade-off: one-time programmability (vs RTAX250SL-1CG624B)
설계 노트
The CCGA624 package uses solder columns, not solder spheres. Land patterns must be designed for high-lead column reflow per the Microchip RTAX-S/SL datasheet package section and IPC-class space workmanship requirements of your program. Provide X-ray inspection access beneath the device, since column solder joints cannot be visually verified. Use symmetric thermal relief on column lands to prevent tombstoning during reflow, and qualify a rework procedure before flight build - CCGA rework requires specialized nozzles and column re-attachment tooling.
Antifuse devices are one-time programmable: the configured netlist routing and timing are frozen and identical on every unit, which aids verification, but a design change requires new programmed parts with associated programming lead time. Freeze the RTL, run Microchip Libero place-and-route, and lock the netlist under configuration control well before the flight-lot programming date. Also remember that radiation tolerance covers the configuration layer; user flip-flops remain SEE-sensitive and require TMR or EDAC per Microchip's RTAX reliability application notes.
The RTAX250SL uses a 1.5 V core with a 0.15 um antifuse process that draws low static power, but dynamic power scales with clock activity and toggle rate. Estimated: for flight power budgets, calculate dynamic power from your post-place-and-route simulation activity files using Microchip's power estimator rather than family headline figures. Sequence the 1.5 V core and I/O rails per the datasheet power-up specification and verify inrush into the CCGA624's decoupling network with measured ESR values on flight-lot capacitors.
With 624 columns and high user-I/O density, manage return paths by assigning solid ground reference planes under every I/O bank and keeping spaceflight bus interfaces (1553, SpaceWire-class links) on length-matched, impedance-controlled routing. Estimated: maintain your program's specified differential impedance (commonly 100 ohm) on paired I/O and reserve the FPGA's segmentable clock resources to isolate detector or bus clocking from switching noise on adjacent banks, per the clocking chapter of the RTAX-S/SL datasheet.
규정 준수 정보
Space-grade ceramic CCGA package; standard CG624B termination and S-suffix lead-free variants exist (RTAX250SL-CGS624B). AEC-Q100 is not applicable to this space-flight product. Extract formal RoHS/REACH declarations from Microchip product pages before contract.
