EFM32G200F32-QFN32T - 32MHz Cortex-M3 32KB Flash MCU | Silicon Labs
MPN: EFM32G200F32-QFN32T ✓ ActiveEFM32G200F32-QFN32T Overview
A microcontroller is a programmable system-on-chip that integrates a processor core, nonvolatile Flash memory, volatile RAM, peripheral interfaces, and clocking into one compact component. The EFM32 Gecko family belongs to the embedded microcontroller and power-management IC hierarchy. It combines deterministic control capability with low-power operation, making it suitable for connected sensors, compact industrial controls, portable instruments, and battery-operated products.
Principal features include a maximum CPU speed of 32 MHz, 32 KB of program Flash, 8 KB of RAM, 24 digital I/O pins, and two 16-bit timers. The device also provides four 12-bit analog-to-digital converter channels and one 12-bit digital-to-analog converter channel. Its operating supply range is 1.98 V to 3.8 V, and the surface-mount package measures 6 mm by 6 mm with an exposed thermal pad.
The Cortex-M3 core supports efficient event-driven firmware, while the Gecko low-power platform offers fast wake-up times and multiple energy-saving modes. These characteristics help reduce both average current draw and response latency in applications that spend most of their time sleeping. Peripherals can be clock-gated to further reduce consumption when their functions are not required.
Typical uses include low-power wireless sensor nodes, building-automation endpoints, compact motor and actuator controllers, portable measurement equipment, and IoT devices that transmit small packets of sensor data. The 32 KB Flash budget is suitable for moderate embedded applications, while 8 KB of RAM accommodates short task stacks and localized data buffers.
When laying out the board, use a thermal-aware exposed-pad pattern with a solid ground plane and multiple short thermal vias. Place the decoupling capacitor close to the supply pins and route analog inputs away from switching nodes. Firmware should enable the deepest suitable sleep mode between events, since average power consumption in an IoT product is often dominated by idle time rather than active processing.
This page combines device specifications, drop-in upgrade options, package-level guidance, and application-oriented design notes to support schematic capture, PCB layout, firmware planning, and component selection.
Drop-in alternatives for EFM32G200F32-QFN32T — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with EFM32G200F32-QFN32T (same form factor and footprint) — differing in Package, Flash Memory, Digital I/O Pins, ADC, Architecture.
EFM32G200F16-QFN32T
✅ Drop-InContact for price
View Datasheet →EFM32G200F64-QFN32T
✅ Drop-InContact for price
View Datasheet →EFM32G210F32-QFN32T
✅ Drop-In ⚠️ Specs Unverified📋 Reference alternative (not in catalog)
EFM32G230F32-QFN32T
✅ Drop-In ⚠️ Specs Unverified📋 Reference alternative (not in catalog)
EFM32G200F32-QFN32
✅ Drop-InContact for price
View Datasheet →EFM32G200F32-QFN32T Maximum Ratings & Electrical Characteristics
| Product Type | 32-bit ARM Cortex-M3 Gecko microcontroller |
| Maximum CPU Frequency | 32 MHz |
| Flash Memory | 32 KB |
| RAM | 8 KB |
| Digital I/O Pins | 24 |
| Timers | 2 x 16-bit |
| ADC | 4 x 12-bit |
| DAC | 1 x 12-bit |
| Supply Voltage Range | 1.98 V to 3.8 V |
| Operating Temperature | -40 C to +85 C |
| Package | 32-QFN exposed pad, 6 mm x 6 mm |
| Mounting Type | Surface mount |
| Architecture | ARM Cortex-M3, 32-bit single-core |
| Program Memory Type | Flash |
| AES Hardware Accelerator | No |
| Internal Oscillator | Internal |
| Low-Power Features | Fast wake-up and energy-saving modes |
EFM32G200F32-QFN32T 32-qfn exposed pad, 6 mm x 6 mm Pin Configuration Guide
Pin configuration for EFM32G200F32-QFN32T (32-qfn exposed pad, 6 mm x 6 mm package). This digital IC includes GPIO, communication interfaces (UART, SPI, I2C), and power pins. Refer to the manufacturer datasheet for alternate pin functions and configuration options. Essential for embedded system design and PCB layout.
No detailed pinout data available for EFM32G200F32-QFN32T.
Refer to the datasheet for full pin configuration.
Typical Applications
EFM32G200F32-QFN32T is suitable for 6 applications: Battery-Powered Wireless Sensor Nodes, Industrial Control and Sensor Hubs, Building Automation Endpoints, Portable Measurement Instruments, Compact Motor and Actuator Control, IoT Data Acquisition and Remote Monitoring.
Battery-Powered Wireless Sensor Nodes
The EFM32G200F32-QFN32T fits compact wireless sensor nodes because its Cortex-M3 core runs up to 32 MHz while the Gecko platform supports fast wake-up and energy-saving modes. The 32 KB Flash stores the radio driver, sensing logic, and protocol state, while 8 KB RAM supports packet buffers and short task stacks. A sensor duty cycle can place the MCU between sleep and active states without adding a separate low-power controller. Firmware should clock-gate unused peripherals, disable unneeded ADC channels, and wake on timer or sensor events. Actual battery life depends on radio transmission energy and the selected sleep mode, so validate current draw in the complete enclosure and battery configuration.
Recommended
Industrial Control and Sensor Hubs
The EFM32G200F32-QFN32T is suitable for small industrial sensor hubs that combine four 12-bit ADC channels, two 16-bit timers, and 24 digital I/O pins in a compact 6 mm by 6 mm footprint. The four ADC inputs can monitor temperature, pressure, or analog process signals, while the timers support periodic sampling and output switching. Its 1.98 V to 3.8 V supply range accommodates common 3.3 V industrial rails after appropriate regulation. Keep analog traces short and isolated from switching nodes, and use the exposed pad as a solid thermal connection. Firmware should use periodic wake-up, debounced digital inputs, and a defined fault state for sensor or communication timeouts.
Recommended
Building Automation Endpoints
The EFM32G200F32-QFN32T can serve as the controller for building-automation endpoints such as occupancy sensors, room controllers, and small HVAC interfaces. Its 24 digital I/O pins provide flexible connections to switches, relays, and digital sensors, while the 12-bit ADC supports analog level monitoring. The energy-saving modes are valuable in facilities where endpoints remain idle for long periods. Use a GPIO interrupt or timer to wake the device, then sample only the required ADC channels and transmit the resulting state. The 32 KB Flash budget suits concise control logic and standardized communication stacks. Validate debounce behavior and relay-driver isolation in hardware rather than relying solely on firmware filtering.
Recommended
Portable Measurement Instruments
The EFM32G200F32-QFN32T supports compact handheld measurement products that combine battery-powered operation, digital sensing, and local data processing. Four 12-bit ADC channels provide adequate resolution for many temperature, pressure, and resistive-sensor measurements, while the one-channel 12-bit DAC can generate an analog reference or test signal. The 32 MHz Cortex-M3 core performs calibration and filtering without requiring a separate processor. Its low-power behavior improves standby time between measurements, provided the analog front end is also placed into a low-power state. Use buffered sensor inputs where source impedance is high, calibrate offset and gain at production, and keep the 1.98 V to 3.8 V supply within the manufacturer limits.
Recommended
Compact Motor and Actuator Control
The EFM32G200F32-QFN32T can control small motors, solenoids, and actuators where deterministic timing and low standby consumption are important. Two 16-bit timers provide the timing resources needed for pulse generation, capture, or periodic control, and the 24 GPIO pins simplify encoder and switch interfacing. Place power transistors and flyback protection outside the MCU footprint, and keep high-current switching nodes away from the analog inputs. The device can sleep between motion commands while retaining configuration in Flash, reducing quiescent demand. Firmware should include overcurrent, timeout, and watchdog recovery behavior. Because the MCU does not directly drive inductive loads, the external driver stage and thermal design determine the achievable duty cycle.
Recommended
IoT Data Acquisition and Remote Monitoring
The EFM32G200F32-QFN32T is appropriate for compact IoT data-acquisition modules that collect a limited number of analog readings and send summarized results over a serial link. The 32 KB Flash can hold networking code, a data packetizer, and application logic, while 8 KB RAM is adequate for short acquisition frames. Schedule ADC conversions and serial transfers with timers rather than continuous polling to reduce power. The one-channel DAC can support sensor compensation or a low-level analog output where required. Use buffered signals and a separate low-noise regulator if the ADC is connected to high-impedance sources. Firmware should buffer results during transient communication outages and retain timestamps through the system real-time counter.
Recommended
Recommended Products Summary
Engineering reference data for EFM32G200F32-QFN32T — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | EFM32G200F16-QFN32T | EFM32G200F64-QFN32T | EFM32G210F32-QFN32T | EFM32G230F32-QFN32T | EFM32G200F32-QFN32 |
|---|---|---|---|---|---|---|
| Package | 32-QFN (6x6) Exposed Pad | 32-QFN (6x6) Exposed Pad | 32-QFN (6x6) Exposed Pad | 32-QFN (6x6) Exposed Pad | 32-QFN (6x6) Exposed Pad | 32-QFN (6x6) Exposed Pad |
| Brand | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs |
| Flash Memory | 32 KB | 16 KB | 64 KB | 32 KB | 32 KB | 32 KB |
Key Differentiators
- Balanced memory and peripheral allocation (vs EFM32G200F16-QFN32T)
- Headroom for larger firmware without changing the footprint (vs EFM32G200F64-QFN32T)
- Low-power Gecko platform with useful mixed-signal resources (vs EFM32G230F32-QFN32T)
Design Notes
Treat the QFN exposed pad as the primary thermal path. Connect it to a low-impedance ground region on the PCB and add several short thermal vias according to the manufacturer land pattern. Keep the pad free of signal traces where possible. Because no junction-to-ambient thermal resistance is stated for this exact ordering code, do not assign a thermal limit without checking the package thermal data and the board's copper geometry.
Place the main supply-decoupling capacitor immediately beside the device power pins, with the shortest possible ground return. Route analog inputs away from switching regulator nodes and digital timing edges. The 32-QFN footprint is compact, so verify pad and mask dimensions against the manufacturer drawing and confirm exposed-pad paste separately if the assembly process requires it.
Do not treat the trailing T ordering suffix as a different electrical variant; it identifies the tape-and-reel ordering form of the same device configuration. The more common mistake is substituting a 16 KB Flash member for a design compiled with 32 KB of images. Check the final linked binary size, reserve space for future updates, and confirm every peripheral pin assignment before approving a substitution.
Low-power performance depends on firmware as much as on the MCU. Put the core into the deepest acceptable sleep mode between events, clock-gate unused peripherals, and disable unused analog channels. Measure average current over a complete operating cycle because wake-up, conversion, and communication bursts can dominate otherwise sleep-state consumption.
Compliance Information
Compliance status must be confirmed from the current manufacturer product documentation or declaration for the exact ordering code. AEC-Q100 is not applicable to this general-purpose microcontroller.