LM324KAN - 14-PDIP Quad Operational Amplifier | Texas Instruments
MPN: LM324KAN ✓ ActiveLM324KAN Overview
An operational amplifier is an active analog device that amplifies the difference between its two inputs. The LM324 family belongs to the broader hierarchy of operational amplifiers, analog amplifiers, linear integrated circuits, and signal-chain semiconductors. Its single-supply capability allows operation from one positive rail and ground, although the complete electrical limits and common-mode behavior should be confirmed in the manufacturer datasheet before fixing system voltages.
The primary feature of the LM324KAN is its integration of four general-purpose amplifier channels into one 14-pin PDIP. This reduces component count and board area compared with four single-amplifier packages. The through-hole PDIP format also suits educational equipment, industrial control prototypes, audio projects, legacy instruments, and maintenance applications where socketed or hand-soldered installation is common.
Each amplifier section includes differential input and output connections arranged in a standard quad-op-amp layout. Pin 11 supplies the positive rail, pin 4 connects to the negative rail, and pins 1, 7, 8, and 14 provide the four outputs. Input pins 2 and 3, 5 and 6, 9 and 10, and 12 and 13 form the four differential input pairs. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks or socket connections.
Typical uses include audio preamplification, sensor-signal conditioning, low-frequency filtering, active feedback, sample-and-hold support, and general instrumentation. Because the LM324KAN is a general-purpose amplifier rather than a precision or high-speed device, its noise, input-bias-current, slew-rate, output-current, and input-offset-voltage characteristics should be checked against the signal amplitude, source impedance, bandwidth, and required accuracy of the design.
When designing around this device, check the maximum supply voltage and input common-mode range at the selected operating voltage. Decoupling capacitors should be placed close to the supply pins, and unused amplifier sections should be configured according to the manufacturer recommendations instead of being left floating. The DIP footprint also requires adequate spacing for through-hole insertion and soldering access.
This page combines device identification, pin-level guidance, application analysis, drop-in alternatives, and practical design notes to support schematic capture, PCB layout, sourcing, and legacy-product maintenance for the LM324KAN.
Drop-in alternatives for LM324KAN — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with LM324KAN (same form factor and footprint) — differing in Amplifier Type, Mounting Type, Package, Architecture, Gain-Bandwidth Product.
LM324AN
✅ Drop-InContact for price
View Datasheet →LM324BAIDR
✅ Drop-InContact for price
View Datasheet →LM2902B
✅ Drop-In📋 Reference alternative (not in catalog)
TL074CN
✅ Drop-In📋 Reference alternative (not in catalog)
LM2902N
✅ Drop-InContact for price
View Datasheet →LM324KAN Maximum Ratings & Electrical Characteristics
| Amplifier Type | General-purpose operational amplifier |
| Number of Amplifiers | 4 circuits |
| Architecture | Quad operational amplifier |
| Supply Type | Single supply |
| Temperature Grade | Military grade (K grade) |
| Package | 14-pin PDIP, through hole |
| Pin Count | 14 pins |
| Mounting Type | Through-hole PCB mounting |
LM324KAN Pin Configuration
| Pin 1 | OUT 1 — Amplifier 1 output |
| Pin 2 | IN- 1 — Amplifier 1 inverting input |
| Pin 3 | IN+ 1 — Amplifier 1 non-inverting input |
| Pin 4 | V- — Negative power supply connection |
| Pin 5 | IN+ 2 — Amplifier 2 non-inverting input |
| Pin 6 | IN- 2 — Amplifier 2 inverting input |
| Pin 7 | OUT 2 — Amplifier 2 output |
| Pin 8 | OUT 3 — Amplifier 3 output |
| Pin 9 | IN- 3 — Amplifier 3 inverting input |
| Pin 10 | IN+ 3 — Amplifier 3 non-inverting input |
| Pin 11 | V+ — Positive power supply connection |
| Pin 12 | IN+ 4 — Amplifier 4 non-inverting input |
| Pin 13 | IN- 4 — Amplifier 4 inverting input |
| Pin 14 | OUT 4 — Amplifier 4 output |
Typical Applications
LM324KAN is suitable for 6 applications: General-Purpose Sensor Signal Conditioning, Audio Preamplification and Mixer Circuits, Industrial Control and Feedback Loops, Active Filters and Low-Frequency Equalization, Test and Measurement Instrumentation, Legacy Equipment Maintenance and Retrofit.
General-Purpose Sensor Signal Conditioning
The LM324KAN suits four-channel sensor-conditioning circuits where a single low-power package must amplify weak analog signals. Each of the four amplifier sections can buffer a sensor output before conversion by an ADC, reducing loading of the sensing element. Because the device operates from a single supply over a wide voltage range, it is practical in battery-powered instrumentation and industrial monitoring. Confirm the input common-mode limits for the selected rail and the required offset accuracy before using it for high-precision measurements.
Recommended
Audio Preamplification and Mixer Circuits
The four independent channels of the LM324KAN can support small-signal audio preamplification, summing stages, and simple mixer functions. Its single-supply capability permits simple biasing from one positive rail and ground, while the PDIP package remains convenient for hobby, educational, and legacy equipment. Audio designs should check the device noise, slew rate, output swing, and stability into the selected load. For very low source impedances or high-gain stages, verify that the feedback network does not amplify input-bias-current errors.
Recommended
Industrial Control and Feedback Loops
The LM324KAN can implement error amplifiers, comparators with hysteresis, and active feedback elements in industrial control boards. Its four channels allow a controller to use separate amplifiers for sensing, error amplification, and auxiliary signal conditioning. The military K-grade ordering option is relevant when the specified environmental range exceeds standard commercial conditions. Validate loop stability, output-current demand, and common-mode headroom across the full operating voltage and temperature range.
Recommended
Active Filters and Low-Frequency Equalization
The LM324KAN is useful in active low-pass, high-pass, and notch-filter stages where four amplifier channels can implement a complete filter network on one board. Its general-purpose architecture provides a cost-effective way to build analog equalization around a single supply. Keep component values within the recommended range and confirm that the closed-loop gain and load do not exceed the amplifier's stability and output-current limits. Decoupling near the supply pins reduces supply-noise coupling into the filtered signal path.
Recommended
Test and Measurement Instrumentation
The LM324KAN fits laboratory and legacy test equipment requiring buffering, summing, and gain stages around sensors and transducers. The through-hole 14-pin PDIP remains practical for socketed construction, repair, and prototype boards, and the four-channel arrangement simplifies inventory for multi-channel instruments. Confirm the grade-specific temperature range and input-offset specifications against the calibration budget. For precision measurements, compare these values with a precision amplifier family before fixing the measurement chain.
Recommended
Legacy Equipment Maintenance and Retrofit
The LM324KAN is a practical replacement target for repairing industrial, educational, audio, and measurement equipment built around the original LM324 14-pin quad footprint. A same-family B-grade option can often be installed without redrawing the PCB when its electrical limits satisfy the original design. Perform a side-by-side review of supply voltage, input bias current, offset voltage, output swing, and temperature grade before substitution. Also confirm that the alternative is available in the required 14-pin PDIP configuration.
Recommended
Recommended Products Summary
Engineering reference data for LM324KAN — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | LM324AN | LM324B | LM2902B | TL074CN | LM2902N |
|---|---|---|---|---|---|---|
| Package | 14-PDIP | 14-PDIP | 14-PDIP | 14-PDIP | 14-PDIP | 14-PDIP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | onsemi |
| Number of Amplifiers | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Architecture | General-purpose operational amplifier | General-purpose operational amplifier | Next-generation LM324 family | Next-generation LM2902 family | JFET-input operational amplifier | General-purpose operational amplifier |
| Supply Configuration | Single-supply capable | Single-supply capable | Single-supply capable | Single-supply capable | Single-supply capable | Single-supply capable |
| Pin Count | 14 pins | 14 pins | 14 pins | 14 pins | 14 pins | 14 pins |
| Drop-In Status | Original 14-pin quad-amplifier device | Same-family DIP alternative | Manufacturer-described drop-in replacement | Manufacturer-described drop-in replacement | Pin-compatible quad-amplifier alternative | Cross-brand pin-compatible alternative |
Key Differentiators
- K-grade ordering option for wider environmental requirements (vs LM2902N)
- Four general-purpose channels in one 14-pin PDIP (vs TL074CN)
- Manufacturer-described next-generation replacement path (vs LM324B)
- Direct same-family DIP alternative (vs LM324AN)
Design Notes
Confirm that the selected supply voltage, input signal range, and ambient temperature remain inside the LM324KAN electrical limits. The K ordering suffix identifies a military-grade option, so it should not be replaced with a commercial-grade part when environmental qualification matters. In single-supply designs, bias non-inverting inputs above ground when the signal would otherwise remain below the usable common-mode range.
Place the supply bypass capacitor close to pin 11 and the ground return close to pin 4, with a short and low-inductance connection path. Route differential input pairs away from switching nodes and high-current return paths. For the 14-pin PDIP, verify component-body clearance, solder-joint access, and whether a socket is needed for maintenance before finalizing the mechanical layout.
Check the quiescent current across all four amplifier sections and account for supply-current changes caused by output loading and input common-mode operation. Use a supply regulator with adequate current margin, especially if the same rail drives sensors, relays, or digital loads. Do not assume the package dissipates heat uniformly because each amplifier section may reach a different operating point.
Do not leave an unused amplifier section floating. Configure each unused channel as a voltage follower with its input tied to a defined reference within the common-mode range, following the manufacturer guidance. Also review noise-gain stability, maximum closed-loop gain, capacitive loading, and output-current limits before using the device in a new precision or high-gain circuit.
Compliance Information
The LM324KAN is a military-grade general-purpose operational amplifier rather than an automotive-qualified device. Compliance status should be confirmed for the exact orderable configuration and current regulatory declarations.