LT1056ACH - 6.5MHz, 16V/µs JFET Op Amp | Analog Devices
MPN: LT1056ACH ✓ ActiveLT1056ACH Overview
A JFET-input operational amplifier is an analog amplifier whose differential input stage uses junction field-effect transistors. The JFET input architecture provides very low input bias current while preserving the low-noise, high-input-impedance behavior required by sensors, transducers, and laboratory instrumentation. Within the broader semiconductor hierarchy, the LT1056ACH belongs to the operational-amplifier family within amplifier and signal-conditioning integrated circuits.
The LT1056ACH combines a guaranteed maximum offset voltage of 150 µV with typical offset voltage of 50 µV. Its typical input offset drift is 1.2 µV/°C, while the guaranteed maximum drift is 4 µV/°C. Typical input bias current is 40 pA at 70°C and 500 pA at 125°C. These characteristics reduce dc error in high-impedance instrumentation and help preserve signal fidelity when source impedance creates meaningful input offset voltage.
The simultaneous availability of 16 V/µs slew rate and 6.5 MHz gain-bandwidth product distinguishes the LT1056 family from slower precision amplifiers. Large-signal slewing improves recovery from overload and supports small-signal bandwidth in feedback configurations. The offset and drift specifications complement that speed, creating an amplifier suitable for laboratory buffers, precision current-to-voltage converters, active filters, and low-level sensor interfaces.
Typical uses include photodiode and other photodetector preamplifiers, precision bridge instrumentation, low-level signal buffers, waveform amplifiers, and active analog filters. In each circuit, the low input bias current limits dc loading, while the 16 V/µs slew rate helps preserve the shape of rapidly changing signals. Designers should still verify input and output voltage limits, gain-bandwidth behavior, load stability, and supply requirements for the intended configuration.
A primary design consideration is feedback stability. High-speed amplifiers can require source, load, and compensation choices that differ from general-purpose precision op amps. Keep input and feedback routing short, use the manufacturer-recommended application topology, and evaluate output loading before increasing gain. The metal-can package also requires adequate clearance from conductive structures and proper handling to avoid mechanical damage.
This page consolidates manufacturer specifications, lifecycle information, sourcing guidance, replacement constraints, and application-focused design notes for engineers evaluating the LT1056ACH. It distinguishes verified drop-in candidates from merely similar amplifiers and emphasizes the combination of precision input behavior, 6.5 MHz bandwidth, and 16 V/µs slew rate that defines the device.
Drop-in alternatives for LT1056ACH — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with LT1056ACH (same form factor and footprint) — differing in Package, Amplifier Type, Mounting Type, Slew Rate, Typical Input Offset Voltage.
LT1056CH
✅ Drop-InContact for price
View Datasheet →LT1056ACH Maximum Ratings & Electrical Characteristics
| Amplifier Type | Precision JFET-input operational amplifier |
| Number of Circuits | 1 circuit |
| Gain-Bandwidth Product | 6.5 MHz |
| Slew Rate | 16 V/µs |
| Typical Input Offset Voltage | 50 µV |
| Maximum Guaranteed Input Offset Voltage | 150 µV |
| Typical Input Offset Drift | 1.2 µV/°C |
| Maximum Guaranteed Input Offset Drift | 4 µV/°C |
| Typical Bias Current at 70°C | 40 pA |
| Typical Bias Current at 125°C | 500 pA |
| Guaranteed Bias Current at 70°C | 150 pA maximum |
| Guaranteed Bias Current at 125°C | 2.5 nA maximum |
| Package | 8-pin TO-5 metal can |
| Mounting Type | Through-hole metal can |
LT1056ACH 8-pin to-5 metal can Pin Configuration Guide
Pin configuration for LT1056ACH (8-pin to-5 metal can package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.
No detailed pinout data available for LT1056ACH.
Refer to the datasheet for full pin configuration.
Typical Applications
LT1056ACH is suitable for 6 applications: Photodiode Preamplifier, Precision Bridge Instrumentation, Laboratory Signal Buffer, Low-Level Active Filter, Precision Current-to-Voltage Conversion, Waveform and Fast Analog Amplifier.
Photodiode Preamplifier
The LT1056ACH fits a photodiode preamplifier because its typical input bias current is only 40 pA at 70°C, reducing errors caused by the photodiode and feedback network. The 6.5 MHz gain-bandwidth product supports higher-bandwidth transimpedance designs, while the 16 V/µs slew rate improves response to rapid photocurrent changes. Designers should calculate feedback resistance, capacitance, noise gain, and stability together because a very high-value feedback resistor combined with stray capacitance can make the complete amplifier oscillate.
Precision Bridge Instrumentation
For strain-gauge and resistive-bridge measurements, the LT1056ACH provides a 150 µV maximum guaranteed input offset voltage and input bias current of 150 pA maximum at 70°C. These characteristics limit errors caused by amplifier input current and offset in high-gain bridge amplifiers. Its 4 µV/°C maximum guaranteed drift also helps control temperature-dependent error. The practical design task is to balance noise gain against bandwidth, because the 6.5 MHz gain-bandwidth product can amplify high-frequency noise and produce ringing in a poorly compensated circuit.
Laboratory Signal Buffer
The LT1056ACH works well as a laboratory buffer for sources with high output impedance or low-level analog signals. Its low input bias current reduces loading of the source, and the 150 µV maximum offset specification helps preserve small dc signals. The 16 V/µs slew rate provides better large-signal behavior than a purely low-frequency precision amplifier, making the device useful for buffer-before-ADC designs. Input and output range checks remain essential because precision offset performance does not extend the legal signal range.
Low-Level Active Filter
The LT1056ACH can implement a precision low-level active filter when both dc accuracy and moderate bandwidth are required. Its typical offset voltage of 50 µV and maximum guaranteed drift of 4 µV/°C help stabilize the passband, while the 6.5 MHz gain-bandwidth product gives designers room to realize higher-order filters. Designers should calculate each closed-loop response from the selected noise gain rather than assuming that the op-amp bandwidth directly sets filter bandwidth, and they should verify phase margin with the actual load.
Precision Current-to-Voltage Conversion
The LT1056ACH is suitable for precision current-to-voltage conversion because low input bias current reduces current error through the source and feedback paths. With a 50 µV typical offset and 4 µV/°C maximum guaranteed drift, it can preserve accuracy in slow but demanding measurements. The 16 V/µs slew rate also allows the output to follow faster current changes than many precision-only amplifiers. Feedback resistor tolerance, input protection, output loading, and bandwidth should be evaluated before using the TO-5 device in a compact measurement module.
Waveform and Fast Analog Amplifier
The LT1056ACH is appropriate for amplifying waveform signals that require faster slew response than ordinary precision op amps provide. Its 16 V/µs slew rate and 6.5 MHz gain-bandwidth product allow useful small-signal bandwidth and quicker recovery from overload. The amplifier can therefore serve in pulse, waveform, or active-filter stages where the slower response of a general precision amplifier would distort signal edges. Confirm output-voltage swing, load capability, and stability before scaling the gain or driving a lower-impedance load.
Engineering reference data for LT1056ACH — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | LT1056CH |
|---|---|---|
| Brand | Analog Devices | Analog Devices |
| Package | 8-pin TO-5 | 8-pin TO-5 |
| Amplifier Type | Precision JFET-input operational amplifier | Precision JFET-input operational amplifier |
| Number of Circuits | 1 circuit | 1 circuit |
| Gain-Bandwidth Product | 6.5 MHz | 6.5 MHz |
| Slew Rate | 16 V/µs | 16 V/µs |
| Maximum Guaranteed Input Offset Voltage | 150 µV | 150 µV |
| Maximum Guaranteed Input Offset Drift | 4 µV/°C | 4 µV/°C |
| Typical Bias Current at 70°C | 40 pA | 40 pA |
Key Differentiators
- Combines precision offset behavior with high-speed response (vs LT1056CH)
- Very low input bias current for precision high-impedance circuits (vs LT1056CH)
- Low thermal drift supports stable dc measurements (vs LT1056CH)
Design Notes
Do not treat every LT1056-family listing as a pin-to-pin substitute. The cross-reference results explicitly warn that some functionally similar alternatives have modified circuits. Compare the complete ordering suffix, pin-description table, operating temperature range, and qualification requirements for LT1056ACH and LT1056CH before replacing the component on an existing board.
The 6.5 MHz gain-bandwidth product and 16 V/µs slew rate require careful feedback-network design. Use the manufacturer's recommended noise-gain topology, keep feedback routing compact, and include a small isolation resistor between the amplifier and capacitive loads when necessary. Verify the closed-loop response with the intended source impedance and load because the maximum small-signal bandwidth does not independently determine closed-loop stability.
Treat the 8-pin TO-5 can as a through-hole precision package. Maintain adequate clearance between the metal can and adjacent conductive components, avoid mechanical stress on the leads, and orient the package according to the manufacturer pin diagram. If a socket is used, verify pin continuity, contact resistance, and thermal behavior; low-bias-current operation is particularly sensitive to contamination and leakage across the board.
Bypass the supply pins with capacitors selected from the manufacturer reference circuit and placed close to the appropriate package pins. Confirm the permitted supply voltage, output swing, input common-mode range, and stability capacitor values in the datasheet before energizing the circuit. Include a controlled startup path if the source impedance or downstream bias network can produce excessive transients during power-up.
Compliance Information
Material-compliance declarations were not stated for the exact LT1056ACH suffix. AEC-Q100 is not applicable to this general-purpose precision operational amplifier. Obtain a current manufacturer declaration for the exact orderable part.