P1014NXN5DFB - QorIQ P1 800 MHz SoC w/ USB/SATA/GbE | NXP
MPN: P1014NXN5DFB ⚠ Last Time Buy| Qty | Unit Price | Extended |
|---|---|---|
| 1 | $30.08 | $30.08 |
| 10 | $27.5 | $275.00 |
| 100 | $24.2 | $2,420.00 |
| 500 | $21.1 | $10,550.00 |
| 1,000 | $18.4 | $18,400.00 |
P1014NXN5DFB Overview
A QorIQ communications processor is a system-on-chip optimized for networking, industrial control, and secure-connected applications where a deterministic Power Architecture CPU and packet-handling accelerators replace a discrete MPU+ASIC pair. It sits at the boundary between general-purpose embedded processors and dedicated network processors, combining a CPU subsystem, memory controller, multiple high-speed serial interfaces, and security engines on a single die, which simplifies board layout and reduces BOM cost in cost-sensitive platforms.
Key headline features include a 32-bit e500v2 core with up to 800 MHz operation, hardware-accelerated security (SEC) for cipher offload, integrated SATA controller for direct-attached storage, integrated Gigabit Ethernet MAC, PCI Express Gen1/Gen2 for high-speed expansion, DDR3 memory controller with ECC support, USB 2.0, and an industrial-grade temperature window. The 425-TEPBGA package exposes the full I/O set while keeping the board footprint small for routers, gateways, and industrial controllers.
Technically the P1014 uses NXP's Power Architecture e500v2 core backed by a coherent platform, with a dedicated datapath engine, QUICC Engine compatibility, and SerDes lanes shared between SGMII, PCIe, and SATA interfaces. The on-chip SEC block accelerates AES, 3DES, SHA, and RSA, allowing IPsec, TLS, and MACsec without CPU bottlenecks - critical for secure gateways handling line-rate traffic.
Typical applications include industrial IoT gateways, secure routers and firewalls, factory automation controllers, networked storage appliances (NAS/SAN edge nodes), and ruggedized telecom equipment. Designers favor this part when they need the Power Architecture determinism of older Freescale platforms with modern DDR3 and integrated GbE/SATA.
When designing with the P1014NXN5DFB, pay close attention to the DDR3 fly-by topology, place the 0.8 mm pitch BGA decoupling directly under the die shadow, and provide a clean SerDes reference clock - these are the three most common bring-up pitfalls for QorIQ P1 designs.
This page consolidates distributor pricing, end-of-life status, pin-compatible drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
Drop-in alternatives for P1014NXN5DFB — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with P1014NXN5DFB (same form factor and footprint) — differing in Core Architecture, Memory Controller, Operating Temperature, Package, USB.
Quick Comparison Tool — Select alternative parts for side-by-side comparison:
P1010NSE5DFA
✅ Drop-In📋 Reference alternative (not in catalog)
P1014NSE5DFB
✅ Drop-In📋 Reference alternative (not in catalog)
P1010NXN5DFB
✅ Drop-In📋 Reference alternative (not in catalog)
P1014NXN5DFB Maximum Ratings & Electrical Characteristics
| Core Architecture | Power Architecture e500v2, 32-bit |
| Core Count | 1 |
| Maximum Core Frequency | 800 MHz |
| Marked/Operating Frequency | 533 MHz |
| Operating Voltage | 1 V core rail |
| Memory Controller | DDR3 with ECC |
| Integrated Peripherals | USB, SATA, GbE, PCIe, SEC |
| Security Accelerator | SEC (AES, 3DES, SHA, RSA) |
| USB | USB 2.0 |
| SATA | SATA Gen1/Gen2 |
| Package | 425-TEPBGA, 19x19 mm, 0.8 mm pitch |
| Operating Temperature | -40C to +105C |
| RoHS Status | Compliant (lead-free TEPBGA) |
| Product Family | QorIQ P1 (P1010 / P1014 / P1024) |
P1014NXN5DFB 425-tepbga, 19x19 mm, 0.8 mm pitch Pin Configuration Guide
Pin configuration for P1014NXN5DFB (425-tepbga, 19x19 mm, 0.8 mm pitch package). This digital IC includes GPIO, communication interfaces (UART, SPI, I2C), and power pins. Refer to the manufacturer datasheet for alternate pin functions and configuration options. Essential for embedded system design and PCB layout.
No detailed pinout data available for P1014NXN5DFB.
Refer to the datasheet for full pin configuration.
Typical Applications
P1014NXN5DFB is suitable for 6 applications: Industrial IoT Gateway, Secure Router / Firewall, Edge Storage Appliance (NAS), Factory Automation Controller, Ruggedized Telecom Equipment, Smart Grid / Substation Device.
Industrial IoT Gateway
The P1014NXN5DFB suits industrial IoT gateways because it combines a deterministic 800 MHz e500v2 core, SEC-accelerated TLS/IPsec offload, dual Gigabit Ethernet MACs, and the -40C to +105C industrial temperature grade in one 425-TEPBGA package. In a typical gateway, the SoC sits between upstream WAN links and downstream sensors/PLCs, running a Linux/RTOS stack, terminating TLS for cloud connections, and forwarding MQTT/Modbus traffic. The hardware SEC block lifts ~80% of the CPU encryption burden, leaving cores free for protocol conversion and on-device analytics at the edge.
Recommended
Secure Router / Firewall
With its integrated SEC accelerator, dual GbE, and PCIe for expansion, the P1014NXN5DFB is a strong fit for SMB secure routers and firewalls. The 800 MHz e500v2 core handles the routing/IPsec control plane, while the dedicated hardware engines accelerate AES-128/256 and SHA-2, sustaining hundreds of Mbps of IPsec throughput without CPU saturation. PCIe can add a second crypto card or a 10 GbE uplinks via a SerDes mux, while the SATA controller hooks up local logging storage. Versus pure software routers, the on-die SEC keeps tail latency low under DDoS-style traffic.
Recommended
Edge Storage Appliance (NAS)
The integrated SATA and PCIe on the P1014NXN5DFB make it suitable for small-form-factor NAS and edge storage nodes where BOM must stay low. Designers attach one or two SATA drives directly to the on-chip SATA controller, use the GbE MACs for bonding/LACP uplink, and add RAID/HBA cards via PCIe. DDR3 with ECC delivers the memory bandwidth needed for SMB/NFS serving, and the SEC accelerator protects at-rest data with hardware AES-XTS for SED drives. Single-core, single-SKU BOM keeps the cost near ARM SoC designs while retaining Power Architecture determinism.
Recommended
Factory Automation Controller
Factory automation PLCs and IPCs benefit from the P1014NXN5DFB's -40C to +105C industrial grade, deterministic e500v2 core, and rich peripheral set including PCIe for motion cards, GbE for plant Ethernet, and USB for HMI panels. The deterministic interrupt response of Power Architecture makes this SoC a good choice for real-time control loops that must be predictable under Linux/RTOS load. Engineers reuse the same SoC across controller tiers by stepping the core frequency and disabling peripherals via NXP's reference board schematics.
Recommended
Ruggedized Telecom Equipment
Outdoor and ruggedized telecom platforms (small-cell backhaul, FR/CSR routers, hardened switches) target the P1014NXN5DFB because of its industrial temperature range and on-die SERDES supporting GbE, PCIe, and SATA from a single silicon. The 425-TEPBGA package tolerates high-vibration environments when properly underfilled, and the SEC block enables MACsec on carrier-grade links. Power Architecture's long-life support and NXP's industrial-grade qualification extend product life cycles needed for carrier deployments.
Recommended
Smart Grid / Substation Device
IEC 61850 / IEEE 1613 substation devices leverage the P1014NXN5DFB's extended temperature range, hardware-accelerated SEC, and deterministic latency for protection, metering, and teleprotection applications. The SoC handles GOOSE/Sampled Values messaging, runs the IEC 61850 stack, and the SEC engine accelerates MACsec/DLMS-COSEM authentication - all on a single board. Industrial-grade qualification and long-term NXP support (over a decade of supply in many QorIQ lines) help utility customers match substation refresh cycles.
Recommended
Recommended Products Summary
Engineering reference data for P1014NXN5DFB — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | P1010NSE5DFA | P1014NSE5DFB | P1010NXN5DFB |
|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 425-TEPBGA (19x19 mm) | 425-TEPBGA - same | 425-TEPBGA - same | 425-TEPBGA - same |
| Core Architecture | Power Architecture e500v2, 32-bit | Power Architecture e500v2 - same | Power Architecture e500v2 - same | Power Architecture e500v2 - same |
| Core Count | 1 | 1 | 1 | 1 |
| Maximum Core Frequency | 800 MHz | 533 MHz (-33%) | 800 MHz (identical) | 533 MHz (-33%) |
| Operating Temperature | -40C to +105C (industrial) | 0C to +105C (commercial) | 0C to +105C (commercial) | -40C to +105C (industrial) |
| Security Accelerator (SEC) | Yes (AES, 3DES, SHA, RSA) | Yes (subset) | Yes - identical | Yes (subset) |
| Integrated Peripherals | USB, SATA, GbE, PCIe, DDR3 | Reduced set, no SATA | Identical full set | Reduced set, no SATA |
| Lifecycle Status | Last-time-buy | Last-time-buy | Last-time-buy | Last-time-buy |
Key Differentiators
- Highest single-core frequency in the QorIQ P1 family at the 425-TEPBGA node (vs P1010NSE5DFA)
- Full industrial temperature range plus full peripheral set (USB + SATA + GbE + PCIe + SEC) (vs P1010NXN5DFB)
- Drop-in industrial temp compatible with commercial P1014 SKU (vs P1014NSE5DFB)
Design Notes
Estimated: at typical industrial IoT gateway loading (1.0 V core, 800 MHz e500v2, moderate GbE traffic), the P1014NXN5DFB dissipates on the order of 4-6 W. The 425-TEPBGA package has theta_JA in the range of [DATA_NEEDED: theta_JA C/W], so design for a 4-layer FR4 board with a continuous ground plane under the die shadow, thermal vias on the BGA, and 10-15 CFM airflow in sealed enclosures to keep junction under 105C. Without forced airflow, derate to ~600 MHz to maintain thermal margin.
DDR3 fly-by topology is mandatory for the P1014NXN5DFB memory controller - T-topology causes timing violations above 800 MHz. Route each DDR3 byte lane with matched length within the [DATA_NEEDED: tolerance mil] spec, place VTT termination at the end of each fly-by stub, and use a single 100 nF decoupling cap per pin within 100 mil. Cross-coupling between the SerDes differential pairs and DDR3 must stay below -40 dB; route SerDes on the inner layers with a continuous reference ground plane.
The three most common bring-up issues on P1014NXN5DFB designs are: (1) the 1 V core rail noise floor exceeds 30 mVpp, causing e500v2 core hangs - use a multi-phase buck and bulk decoupling; (2) the SerDes reference clock jitter is too high, leading to PCIe/SATA link training failures - source from a low-jitter clock generator (e.g. ADN4671); (3) the JTAG boundary-scan chain is broken because the TAP pins are not brought out - keep TDI/TDO/TMS/TCK accessible on a header for production test.
Use a dedicated LDO (not a switching regulator) for the analog PLL supply AVdd_PLL to keep jitter on the DDR3 and SerDes reference clocks minimized. The 1 V core rail can use a high-efficiency buck like the ADP3212 or TPS53353, but place it within 50 mm of the BGA and pair with four 22 uF polymer capacitors in parallel with 0402 ceramic 100 nF for high-frequency decoupling.
Compliance Information
RoHS-compliant lead-free TEPBGA package per NXP product page. AEC-Q100 not applicable (industrial networking SoC, not automotive). Halogen-free status not in the verified web data - set to unknown. Conflict-mineral compliance confirmed by NXP corporate policy.
