R5F10PGJKNA#U5 - 24MHz 16-Bit MCU with 256KB Flash | Renesas Electronics
MPN: R5F10PGJKNA#U5 ✓ ActiveR5F10PGJKNA#U5 Overview
An RL78 microcontroller is a compact embedded-processing device designed for low-consumption control applications. The RL78 architecture is part of the broader microcontroller hierarchy, combining a CPU core, flash program memory, data memory, timers, communication peripherals, analog functions, and GPIO in one integrated circuit. These devices are commonly used where deterministic control, low standby power, and integrated automotive communication functions are more important than high-end processor performance.
The R5F10PGJKNA#U5 combines a 16-bit CPU operating at 24 MHz with 256 KB of flash organized as 256K x 8. Its integrated CAN and LIN modules support vehicle networking and other distributed automotive control systems. The family also supports BLDC motor control through timer RD, comparator, and functional-safety features. These characteristics make the device suitable for body-electronics controllers, motor-control systems, gateways, sensor nodes, and CAN-connected industrial equipment.
The 48-HVQFN package provides a compact surface-mount footprint for space-constrained control boards. Because the exposed-pad package concentrates thermal and electrical requirements into a small area, PCB construction must follow the Renesas land-pattern, solder-mask, paste, and reflow guidance. Automotive qualification information must also be confirmed against the exact ordering code and current manufacturer documentation before production release.
Typical implementations include CAN body modules, LIN sub-networks, brushless DC motor controllers, battery and charging subsystems, and compact automotive sensor nodes. In these systems, the MCU can execute application firmware while coordinating communications through its integrated CAN and LIN peripherals, reducing the need for separate interface devices. Its 256 KB flash capacity also provides room for larger control routines, diagnostics, and communication tables.
For a new design, verify the exact pin multiplexing, peripheral availability, clock limits, electrical characteristics, and supported development environment in the manufacturer datasheet. Production firmware should include checks for reset behavior, watchdog operation, communication error handling, and brownout conditions. Board bring-up should begin with a clean power supply, controlled clock startup, and continuity checks around the exposed pad before peripheral testing.
This product page consolidates the confirmed 24 MHz, 16-bit, 256 KB flash, automotive, CAN, LIN, and 48-HVQFN attributes into an application-oriented selection guide. It also distinguishes confirmed device facts from parameters that require formal datasheet review and directs sourcing requests through the XAIPART Request a Quote form.
Drop-in alternatives for R5F10PGJKNA#U5 — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
No drop-in alternatives available for this product.
Request AlternativesR5F10PGJKNA#U5 Maximum Ratings & Electrical Characteristics
| Product Type | 16-bit microcontroller (MCU) |
| Product Series | RL78/F14 |
| CPU Maximum Frequency | 24 MHz |
| CPU Word Length | 16 bit |
| Flash Memory | 256 KB |
| Flash Organization | 256K x 8 |
| CAN Interface | Built-in CAN module |
| LIN Interface | Built-in LIN module |
| BLDC Motor Control | Supported through timer RD, comparator, and functional-safety features |
| Package | 48-HVQFN (7 x 7 mm) |
| Pin Count | 48 pins |
| Mounting Type | Surface mount |
| Automotive Qualification | AEC-Q100 automotive device |
| Low-Consumption Feature | RL78/F14 series positioned for low consumption current |
R5F10PGJKNA#U5 48-hvqfn (7 x 7 mm) Pin Configuration Guide
Pin configuration for R5F10PGJKNA#U5 (48-hvqfn (7 x 7 mm) package). This digital IC includes GPIO, communication interfaces (UART, SPI, I2C), and power pins. Refer to the manufacturer datasheet for alternate pin functions and configuration options. Essential for embedded system design and PCB layout.
No detailed pinout data available for R5F10PGJKNA#U5.
Refer to the datasheet for full pin configuration.
Typical Applications
R5F10PGJKNA#U5 is suitable for 6 applications: Automotive CAN Body Controller, LIN Sensor and Sub-Network Node, BLDC Motor Control, Automotive Gateway and Communication Hub, Compact Industrial Control Node, Battery and Charging Controller.
Automotive CAN Body Controller
The R5F10PGJKNA#U5 fits an automotive body controller because its RL78/F14 architecture combines a 16-bit CPU at 24 MHz with 256 KB of flash and a built-in CAN module. It can execute door, lighting, input, or centralized body-control logic while exchanging diagnostic and status data through the vehicle network. The 256 KB program-memory capacity supports control routines, diagnostic tables, and communication software without requiring a separate memory device. Its 48-HVQFN 7 x 7 mm package also helps preserve board area in compact electronic control units. Use the manufacturer pin table and reference design guidelines for CAN routing, termination, decoupling, exposed-pad assembly, and production test access.
Recommended
LIN Sensor and Sub-Network Node
The R5F10PGJKNA#U5 is appropriate for a compact LIN node because the RL78/F14 includes both LIN and CAN modules. A LIN-connected sensor, actuator, or gateway can use one MCU for application logic, diagnostics, and communication while retaining CAN for backbone or gateway communication. The 24 MHz CPU supports responsive peripheral control and protocol handling, and 256 KB flash accommodates calibration and diagnostic routines. Designers should use the Renesas pin and electrical documentation to allocate LIN, wake-up, timer, and communication resources. PCB implementation should separate sensitive LIN routing from switching nodes and provide local supply bypassing near the MCU.
Recommended
BLDC Motor Control
The R5F10PGJKNA#U5 supports BLDC motor-control systems through the RL78/F14 family's timer RD, comparator, and functional-safety capabilities. At 24 MHz, the 16-bit core can coordinate commutation, sensor evaluation, fault handling, and supervisory logic for compact motor controllers. The built-in CAN and LIN interfaces can connect the motor controller to broader vehicle or industrial networks, reducing external communications hardware. Application design still requires a suitable three-phase gate driver, MOSFET power stage, current sensing, overcurrent protection, and firmware-safe timing. Validate timing, comparator routing, thermal margins, and exposed-pad heat spreading against the manufacturer documentation.
Recommended
Automotive Gateway and Communication Hub
The R5F10PGJKNA#U5 fits a vehicle gateway where both CAN and LIN connectivity are required in a compact controller. Its 16-bit RL78 core and 24 MHz clock can handle protocol conversion, message filtering, diagnostics, and application-level coordination, while 256 KB flash provides sufficient room for firmware and configuration data. Consolidating two network interfaces into one MCU can reduce board area and simplify the design, although total CAN transceiver count remains application-dependent. Keep communication traces controlled, provide isolated or protected interfaces where required by the vehicle network architecture, and follow automotive ESD, EMC, grounding, and reflow requirements during implementation.
Recommended
Compact Industrial Control Node
The R5F10PGJKNA#U5 can serve in compact industrial equipment that needs deterministic embedded control, low-consumption behavior, and network connectivity. Its 16-bit CPU at 24 MHz, 256 KB flash, CAN module, and LIN module suit motor controls, condition-monitoring controllers, actuators, and distributed equipment nodes. The 48-HVQFN package supports compact board construction, while the RL78/F14 feature set allows communication and control functions to share one device. For industrial use, evaluate the exact operating-temperature grade, isolation, surge protection, EMC performance, and functional-safety requirements. Use the part as designed only if its automotive-oriented ordering code and qualification records meet the end application's standards.
Recommended
Battery and Charging Controller
The R5F10PGJKNA#U5 is suitable for a compact battery-monitoring or charging-control subsystem when the design benefits from low-consumption embedded control and automotive-network integration. The 24 MHz RL78 core can supervise measurements, enforce operating states, manage diagnostics, and communicate status over CAN or LIN. With 256 KB flash, the controller can combine application logic, calibration tables, and fault records in one device. The MCU does not replace power-conversion or battery-measurement circuitry, so designers still need suitable sensing, balancing, protection, and actuator stages. Confirm the ADC, timer, comparator, and communication resources needed by the final design in the manufacturer datasheet before assigning peripheral functions.
Recommended
Recommended Products Summary
Engineering reference data for R5F10PGJKNA#U5 — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product |
|---|---|
| Brand | Renesas Electronics |
| Package | 48-HVQFN (7 x 7 mm) |
| Product Series | RL78/F14 |
| CPU Word Length | 16 bit |
| Maximum CPU Frequency | 24 MHz |
| Flash Memory | 256 KB (256K x 8) |
| CAN Interface | Built-in CAN module |
| LIN Interface | Built-in LIN module |
| Automotive Qualification | AEC-Q100 automotive device |
| BLDC Motor Control | Supported through timer RD, comparator, and functional-safety features |
Key Differentiators
- Integration of CAN and LIN in one automotive MCU (vs AT90CAN64-16MUR)
- Compact 48-pin automotive package (vs MSP430F5519IPN)
- Dedicated BLDC control support (vs ATMEGA808-AU)
Design Notes
Construct the board from the Renesas 48-HVQFN land pattern and exposed-pad drawing for R5F10PGJKNA#U5. Place input and bypass capacitors close to their associated supply pins, use a continuous ground reference where practical, and avoid routing fast communication signals directly beneath the exposed pad. Confirm solder-mask and paste geometry against the current package drawing before releasing production artwork.
Route CAN and LIN interfaces away from switching power stages and high-current motor edges. Keep clock and reset paths short, avoid stubs on communication nets, and provide clean return paths beneath signals. CAN interface layout should follow the transceiver manufacturer's recommendations, including bus routing, protection placement, and grounding appropriate to the vehicle or industrial environment.
The 48-HVQFN exposed pad is the primary path for heat transfer into the PCB. Implement a thermal-via and copper-pour strategy approved for the land pattern, and derive junction temperature from actual operating loss, ambient conditions, board construction, and the manufacturer thermal model. A compact enclosure may reduce heat dissipation even when the package itself is small, so thermal validation belongs in the assembled-unit test plan.
Do not substitute the MCU solely because another device also offers CAN or LIN. Verify every pin, supply voltage, peripheral instance, interrupt vector, clock requirement, and exposed-pad connection in the manufacturer datasheet. Also check development-tool support, programming method, startup behavior, watchdog configuration, and automotive qualification before migrating an existing design.
Compliance Information
The R5F10PGJKNA#U5 is identified as an AEC-Q100 automotive MCU. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation in the current manufacturer product documentation.