SPC5642AF2MVZ3 32-Bit 80MHz Automotive MCU | NXP
MPN: SPC5642AF2MVZ3 ✓ Active| Qty | Unit Price | Extended |
|---|---|---|
| 1 | $0 | $0.00 |
| 10 | $0 | $0.00 |
| 100 | $0 | $0.00 |
| 500 | $0 | $0.00 |
| 1,000 | $0 | $0.00 |
SPC5642AF2MVZ3 Overview
A microcontroller is a semiconductor system-on-chip that integrates a processor core, program memory, data memory, peripherals, interrupt control, and communication interfaces into one device. Automotive powertrain controllers use this integration to execute control algorithms, monitor sensors, drive actuators, enforce timing constraints, and support diagnostic and safety functions. The SPC5642AF2MVZ3 belongs to the MPC56xx Qorivva family and is a complex automotive MCU rather than a general-purpose low-power controller.
Key verified characteristics include a 32-bit Power Architecture core, 2 MB of flash memory, 80 MHz maximum clock, a -40°C to +105°C operating-temperature range, and an automotive-grade PBGA-324 package. The package and temperature rating suit demanding engine and transmission environments, but the available source data does not specify RAM, peripheral details, flash organization, voltage limits, or exact safety-certification status. Those omissions are marked separately rather than inferred from the device family.
The controller can serve as the central real-time processor in an engine-control unit, transmission-control unit, powertrain controller, or chassis electronics. Its 80 MHz clock and 2 MB program memory provide substantial execution and code-storage capacity for control software, while the automotive temperature grade supports operation across a wide industrial thermal range. Exact actuator capability and interface coverage must be confirmed against the manufacturer datasheet before design release.
The principal design consideration is software and hardware validation. A PBGA-324 device requires a carefully designed escape-routing strategy, controlled power and ground distribution, adequate thermal design, and assembly-process control. Firmware must also be checked for timing, diagnostic coverage, watchdog behavior, startup sequencing, and application-specific safety requirements. The -40°C to +105°C specification is not a substitute for a complete automotive qualification review.
This page consolidates the verified distributor and manufacturer descriptions, identifies the documented automotive use cases, and separates confirmed specifications from data still required for engineering evaluation. It is intended to support component identification, sourcing, and preliminary architecture planning rather than replace the NXP datasheet, reference manual, errata, or vehicle-specific validation process.
Drop-in alternatives for SPC5642AF2MVZ3 — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with SPC5642AF2MVZ3 (same form factor and footprint) — differing in Core Architecture, Package, Operating Temperature Range, Product Type, Series.
Quick Comparison Tool — Select alternative parts for side-by-side comparison:
SPC5642AF2MVZ2
✅ Drop-In📋 Reference alternative (not in catalog)
SPC5642AF2MVZ2R
✅ Drop-In📋 Reference alternative (not in catalog)
SPC5643LFF2MMM1R
✅ Drop-In✓ In Stock
$24.85 / Unit
View Datasheet →SPC5748GGK1VM
✅ Drop-In✓ In Stock
$34.16 / Unit
View Datasheet →MPC555LFAVR40
✅ Drop-In ⚠️ Specs Unverified✓ In Stock
Contact for price
View Datasheet →MPC555LFMZP40
✅ Drop-In ⚠️ Specs Unverified✓ In Stock
Contact for price
View Datasheet →MPCZ565MVR56
✅ Drop-In ⚠️ Specs Unverified✓ In Stock
$52.75 / Unit
View Datasheet →SPC5642AF2MVZ3 Maximum Ratings & Electrical Characteristics
| Device Type | 32-bit automotive microcontroller |
| Processor Core | Power Architecture core |
| Architecture | 32-bit |
| Maximum Operating Frequency | 80 MHz |
| Flash Memory | 2 MB |
| Flash Organization | 2M x 8 bits |
| Family | MPC56xx Qorivva |
| Operating Temperature Range | -40°C to +105°C |
| Temperature Grade | Automotive Grade |
| Package Type | PBGA-324 |
| Package Body Size | 23 mm x 23 mm |
| Terminal Form | Ball |
| Mounting Type | Surface Mount |
| Intended Applications | Powertrain, chassis, engine control, transmission control, and industrial applications |
SPC5642AF2MVZ3 23 mm x 23 mm Pin Configuration Guide
Pin configuration for SPC5642AF2MVZ3 (23 mm x 23 mm package). This digital IC includes GPIO, communication interfaces (UART, SPI, I2C), and power pins. Refer to the manufacturer datasheet for alternate pin functions and configuration options. Essential for embedded system design and PCB layout.
No detailed pinout data available for SPC5642AF2MVZ3.
Refer to the datasheet for full pin configuration.
Typical Applications
SPC5642AF2MVZ3 is suitable for 6 applications: Mid-Range Gasoline Engine Control, Direct-Injection Engine Management, Advanced Transmission Control, Powertrain and Chassis Control, Industrial powertrain Equipment, Engine Test and Calibration Systems.
Mid-Range Gasoline Engine Control
SPC5642AF2MVZ3 fits mid-range gasoline engine-control units because its 32-bit Power Architecture core runs at up to 80 MHz and its 2 MB flash provides room for injection, ignition, knock-control, diagnostics, and calibration software. The verified manufacturer description specifically targets powertrain applications, while the -40°C to +105°C grade supports automotive thermal environments. In an ECU, the MCU would process sensor inputs, execute control laws, and coordinate actuator outputs. Final suitability depends on confirming the required PWM, ADC, timer, CAN, diagnostic, and actuator-driver interfaces in the complete datasheet.
Recommended
Direct-Injection Engine Management
The SPC5642AF2MVZ3 is a plausible fit for direct-injection engine management because the verified data identifies it for safety-critical powertrain applications and provides 80 MHz processing with 2 MB flash. That combination can support injector sequencing, cylinder identification, combustion feedback, torque management, and OBD diagnostics when the required peripherals are available. The device's -40°C to +105°C rating helps address engine-compartment temperature variation. Engineers must still validate injector drive interfaces, supply tolerances, timing protection, watchdog strategy, and safety diagnostics before approving the MCU for a production engine platform.
Recommended
Advanced Transmission Control
For advanced transmission control, SPC5642AF2MVZ3 offers an automotive-grade 32-bit Power Architecture MCU with 80 MHz performance and 2 MB of program storage. Those resources can support shift-control logic, clutch and solenoid management, pressure-related calculations, sensor fusion, diagnostic routines, and communication tasks. The verified distributor description explicitly associates the MPC56xx family with advanced transmission applications. Because the supplied data does not expose the complete peripheral list or safety certification, the design team should confirm motor-control timers, communication interfaces, diagnostic channels, and functional-safety requirements in the authoritative NXP documentation.
Recommended
Powertrain and Chassis Control
SPC5642AF2MVZ3 is positioned for integrated powertrain and chassis electronics, where one controller may coordinate engine-related functions with vehicle dynamics or body systems. Its 32-bit architecture, 2 MB flash, and -40°C to +105°C temperature grade provide a useful baseline for embedded automotive software. The verified NXP description names safety-critical powertrain and chassis applications, but it does not establish a particular communication topology or safety level. Before partitioning functions across a vehicle network, verify CAN or other interface availability, diagnostic coverage, startup behavior, and failure-mode requirements.
Recommended
Industrial powertrain Equipment
The same automotive-grade characteristics that support engine and transmission control can suit industrial powertrain equipment operating in harsh temperature environments. SPC5642AF2MVZ3 provides an 80 MHz 32-bit core and 2 MB flash for real-time control software, while its -40°C to +105°C range exceeds the typical commercial indoor range. The verified chipdig description also mentions industrial applications in addition to automotive engine and transmission control. Deployment still requires checking EMC, supply regulation, environmental vibration, input protection, and long-term availability, none of which are fully specified in the supplied source data.
Recommended
Engine Test and Calibration Systems
SPC5642AF2MVZ3 can serve as the target MCU in engine test benches, calibration equipment, and powertrain development platforms when its automotive interfaces and memory architecture are suitable. The 80 MHz Power Architecture core provides real-time execution capability, and 2 MB flash permits substantial control firmware and calibration code. A test system may use the MCU for closed-loop actuator control while external instrumentation handles measurement and logging. The available data does not identify measurement inputs, debug interfaces, or communication peripherals, so engineers should verify those functions and the development toolchain before using the device in a new test fixture.
Recommended
Recommended Products Summary
Engineering reference data for SPC5642AF2MVZ3 — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | SPC5642AF2MVZ2 | SPC5642AF2MVZ2R | SPC5643LFF2MMM1R | SPC5748GGK1VM | MPC555LFAVR40 |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | PBGA-324 | PBGA-324 - same verified family package | PBGA-324 - same verified family package | PBGA-324 - candidate package requires validation | PBGA-324 - candidate package requires validation | PBGA-324 - candidate package requires validation |
| Application Positioning | Powertrain and chassis | SPC5642-series automotive application | SPC5642-series automotive application | Automotive controller family candidate | Automotive controller family candidate | Automotive powertrain family candidate |
| Pinout Compatibility | PBGA-324 | Requires manufacturer pin-map comparison | Requires manufacturer pin-map comparison | Requires manufacturer pin-map comparison | Requires manufacturer pin-map comparison | Requires manufacturer pin-map comparison |
Key Differentiators
- MPC56xx Qorivva automotive positioning (vs SPC5642AF2MVZ2)
- 2 MB flash for control and diagnostics software (vs MPC555LFAVR40)
- Automotive thermal range (vs TMS320F28335ZJZS)
- Power Architecture automotive controller focus (vs SPC5642AF2MVZ2R)
Design Notes
Treat the PBGA-324 footprint as a controlled automotive assembly interface rather than a generic BGA layout. Use the NXP package drawing to define the land pattern, ball map, escape routing, and via strategy. Keep power and ground distribution continuous across the device, provide multiple access points for high-current domains, and route sensitive interfaces away from noisy switching and actuator-return paths. Validate the stack-up and manufacturing rules with the assembler because the supplied data does not specify the recommended pad dimensions or layer count.
The verified temperature range is -40°C to +105°C, but that range does not establish the controller's junction-to-ambient limit or allowable dissipation. Thermal design should begin with measured or datasheet-based power values for the selected clock, peripherals, and I/O loading. Estimate junction temperature from board ambient, copper area, thermal vias, and the package thermal model rather than assuming the PBGA can dissipate every automotive ECU power budget without qualification. Confirm the final assembly and enclosure in an environmental test chamber.
Power, reset, clock, and communication signals require disciplined return paths in a 23 mm by 23 mm PBGA-324 device. Place decoupling structures at the corresponding power balls, preserve a continuous ground reference, and keep high-current actuator returns separated from sensitive control signals. Use the complete NXP datasheet and reference design to confirm which interfaces require special routing, isolation, filtering, or timing margins. Do not infer pin functions or peripheral locations from the package name alone.
A related MPN or matching flash size is not proof of drop-in compatibility. Before replacing SPC5642AF2MVZ3, compare the exact NXP ordering code, PBGA-324 ball map, supply voltage, memory map, peripheral assignments, interrupt architecture, startup behavior, watchdog and diagnostic functions, temperature grade, and qualification records. Also verify software binary compatibility and test tooling. The cross-reference results supplied here identify related parts but do not provide enough evidence to approve an unqualified substitution.
Compliance Information
The verified sources identify the MCU as automotive grade but do not explicitly state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. These fields remain unknown rather than being inferred.
