Microchip Technology

SY88703VKI - 622Mbps PECL Post Amplifier | Microchip

MPN: SY88703VKI ✓ Active
3.3V or 5V Vdss 10-pin MSOP, 3.00 mm width Package
MOQ: 1 |

SY88703VKI Overview

The Microchip Technology SY88703VKI is a 3.3V or 5V low-power limiting post amplifier designed for data rates up to 622 Mbps in a 10-pin MSOP package. It converts the linear output of a transimpedance amplifier into a limited PECL waveform for fiber-optic receiver links. The device also provides a TTL-compatible loss-of-signal indication and a TTL-compatible enable input.

A limiting post amplifier is the decision and output stage commonly placed between a fiber-optic transimpedance amplifier and the receiver logic or clock-and-data-recovery circuitry. Its role within the optical receiver hierarchy is to restore usable signal amplitude and edge timing after noise, attenuation, and amplitude variation have accumulated in the analog front end. The SY88703VKI belongs to the PECL interface family used for high-speed telecommunications and data-communication links.

The principal operating features include operation from a single 3.3V or 5V supply and data rates up to 622 Mbps. Two PECL data outputs provide differential signaling for noise immunity and reduced electromagnetic emissions. The TTL loss-of-signal output is chatter-free, while the TTL enable input provides a simple control interface. A programmable loss-of-signal level allows the system to select a detection threshold appropriate to the characteristics of the upstream transimpedance amplifier.

The limiting architecture quantizes the incoming analog waveform and produces consistent PECL-level outputs. This is useful because a transimpedance amplifier may deliver a signal whose amplitude varies over time and contains substantial noise. The post amplifier establishes the required digital output levels while leaving the primary signal recovery and amplification task to the preceding analog stage. The SY88703VKI is therefore a link-interface component rather than a general-purpose voltage amplifier or comparator.

Typical uses include 622-Mbps fiber-optic receivers, optical communication modules, synchronous data links, clock recovery interfaces, and systems that require PECL-compatible outputs with loss-of-signal monitoring. The dual PECL outputs are particularly appropriate for balanced receiver connections, while the separate enable and LOS functions simplify supervisory logic. System timing and link-budget analysis should include the propagation delay and jitter of the limiting stage.

For PCB implementation, place the device close to the transimpedance amplifier and maintain short, controlled-impedance routes for the high-speed PECL outputs. Use the manufacturer's recommended termination and decoupling arrangements, and provide adequate clearance between complementary data paths. The 10-pin MSOP package supports compact optical-interface designs, although thermal performance and signal integrity remain important at 622 Mbps.

This page combines the device's fiber-optic receiver role, power and signaling characteristics, application guidance, package details, and practical implementation considerations. It also distinguishes documented functions from parameter areas that require confirmation against the manufacturer datasheet, helping engineers plan receiver design without relying on a generic limiting-amplifier description.

Drop-in alternatives for SY88703VKI — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

No drop-in alternatives available for this product.

Request Alternatives

SY88703VKI Maximum Ratings & Electrical Characteristics

Product Type Low-power limiting post amplifier
Supply Voltage 3.3V or 5V
Maximum Data Rate 622 Mbps
Data Output Logic Differential PECL
Number of Data Outputs 2 outputs
Loss-of-Signal Output TTL-compatible, chatter-free
Enable Input TTL-compatible
LOS Threshold Programmable
Supply Configuration Single supply
Package 10-pin MSOP, 3.00 mm width
Mounting Type Surface mount

SY88703VKI 10-pin msop, 3.00 mm width Pin Configuration Guide

Pin configuration for SY88703VKI (10-pin msop, 3.00 mm width package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.

10-pin msop, 3.00 mm width package pinout diagram for SY88703VKI

No detailed pinout data available for SY88703VKI.

Refer to the datasheet for full pin configuration.

Typical Applications

SY88703VKI is suitable for 6 applications: 622-Mbps Fiber-Optic Receiver, PECL Clock-and-Data Recovery Interface, Optical Communication Module, Synchronous Telecommunications Link, Optical Link Loss Monitoring, High-Speed Digital Receiver Front End.

🌐

622-Mbps Fiber-Optic Receiver

The SY88703VKI is suitable for the signal-restoration stage of a 622-Mbps fiber-optic receiver because it supports data rates up to 622 Mbps and produces differential PECL outputs from a transimpedance amplifier's linear signal. Place it downstream of the TIA and upstream of the CDR or recovery logic. The limiter's 3.3V or 5V operation supports two common receiver rail plans, while its chatter-free TTL LOS output allows supervisory circuitry to detect a signal outside the programmed detection threshold.

⏱️

PECL Clock-and-Data Recovery Interface

The SY88703VKI can condition the recovered clock and data signals that follow an optical transimpedance amplifier in a PECL-based CDR interface. Its limiting function produces consistent logic levels from an analog waveform whose amplitude and noise may vary. Operation up to 622 Mbps provides design margin for the stated link class, while differential outputs reduce susceptibility to common-mode noise. The board must use short, impedance-controlled PECL routes and the termination arrangement specified by the manufacturer.

🔧

Optical Communication Module

Compact optical modules can use the SY88703VKI to convert a TIA output into the PECL interface expected by the module's digital recovery circuitry. The 10-pin MSOP package conserves board area compared with larger packages, which is valuable in pluggable and compact transceiver designs. The SY88703VKI's TTL enable input supports receiver-state control, and its programmable, chatter-free loss-of-signal output provides a dedicated fault indication without burdening the host interface.

📡

Synchronous Telecommunications Link

The SY88703VKI fits synchronous telecommunications receiver paths that use PECL and require deterministic signal limiting at data rates up to 622 Mbps. It is especially relevant where a TIA output can vary with optical input power or accumulated noise. Placing the limiter close to the TIA minimizes exposure to additional noise and edge degradation. Designers should evaluate propagation delay, jitter, output-level, and loss-of-signal threshold limits against the specific link budget.

🧩

Optical Link Loss Monitoring

The SY88703VKI supports receiver supervision through its dedicated TTL loss-of-signal output and programmable detection level. The chatter-free indication helps system logic distinguish a persistently invalid receive condition from brief signal transitions. In an optical module, this output can be combined with enable control and host monitoring to report link health. The threshold must be configured so normal amplitude variation does not cause false indications while genuine loss is detected promptly.

🖥️

High-Speed Digital Receiver Front End

The SY88703VKI can serve as the limiting interface in a high-speed receiver front end built around a separate TIA or other analog detector stage. Its 3.3V or 5V single-supply capability accommodates different logic ecosystems, and its two PECL outputs support balanced interconnects. The device does not replace the TIA's gain and noise performance; it converts the TIA result into standardized PECL waveforms. Timing and jitter margins should therefore be evaluated for both stages.

What is the SY88703VKI and what does it do?
The SY88703VKI is a low-power limiting post amplifier for fiber-optic receivers operating at up to 622 Mbps. According to the Microchip Technology manufacturer datasheet, it accepts the linear output of a transimpedance amplifier, quantizes that signal, and provides PECL-level outputs. It also includes a chatter-free TTL loss-of-signal output, a TTL enable input, and a programmable loss-of-signal threshold.
What is the operating voltage of the SY88703VKI?
The SY88703VKI operates from a single 3.3V or 5V supply. The manufacturer datasheet identifies both voltage options for high-speed PECL receiver designs. This makes the amplifier suitable for systems using either 3.3V or 5V interface rails, subject to the voltage limits, decoupling, and output-level conditions specified for the selected supply configuration.
What is the maximum data rate of the SY88703VKI?
The SY88703VKI supports data rates up to 622 Mbps. According to the Microchip Technology manufacturer datasheet, it is a limiting post amplifier intended for high-speed fiber-optic receiver links. Its PECL outputs restore consistent logic levels after the transimpedance amplifier, while the high-speed signal path must be routed with controlled impedance and appropriate termination.
Where can I download the SY88703VKI datasheet PDF?
The official Microchip Technology SY88703V datasheet PDF is available at the manufacturer link on this page. It documents the device description, 3.3V and 5V operation, 622-Mbps capability, PECL outputs, TTL enable function, and loss-of-signal features. Use the manufacturer document for the authoritative pin-description table, timing limits, recommended application circuit, and package dimensions.
Where can I find the SY88703VKI pinout?
The SY88703VKI pin assignments are shown in the pin-description table of the official Microchip Technology SY88703V manufacturer datasheet. The device uses a 10-pin MSOP package and provides PECL data outputs, supply and ground connections, TTL enable, and TTL loss-of-signal functions. Use that table when assigning PCB nets and confirming exposed or no-connect conditions.
Can the SY88703VKI be used in a 622-Mbps fiber-optic receiver?
Yes, the SY88703VKI is specifically designed for 622-Mbps fiber-optic receiver links. It follows a transimpedance amplifier and converts its linear output into limited PECL waveforms. According to the Microchip Technology manufacturer datasheet, the device also supports 3.3V and 5V operation and provides chatter-free TTL loss-of-signal detection for receiver supervision.
What are the key specifications engineers should know about SY88703VKI?
The key SY88703VKI specifications are a 622-Mbps maximum data rate, single 3.3V or 5V operation, differential PECL outputs, a TTL-compatible enable input, and a chatter-free TTL loss-of-signal output. The Microchip Technology manufacturer datasheet also identifies a programmable loss-of-signal threshold. These features place the device between a transimpedance amplifier and PECL-based recovery or logic circuitry.
How does the SY88703VKI loss-of-signal output work?
The SY88703VKI provides a chatter-free TTL loss-of-signal output, and its detection level is programmable. According to the Microchip Technology manufacturer datasheet, this output reports an invalid or unsuitable receive signal so supervisory logic can identify a failed link. The threshold should be selected with the transimpedance amplifier's gain, noise, and expected signal-amplitude range in mind.
What is the difference between SY88703VKI and SY88703VKI-TR?
The SY88703VKI and SY88703VKI-TR identify the same SY88703V limiting post amplifier in different ordering or packaging contexts; the SY88703VKI-TR designation is associated with tape-and-reel shipment. The device description remains a 3.3V or 5V, 622-Mbps PECL limiting post amplifier with TTL loss-of-signal and enable functions. Confirm the ordering suffix and package drawing before procurement.
When should I choose the SY88703VKI over another fiber-optic post amplifier?
Choose the SY88703VKI when the receiver requires a limiting stage operating up to 622 Mbps with differential PECL outputs and a single 3.3V or 5V supply. Its TTL enable and chatter-free loss-of-signal functions also help when the system requires local link supervision. Selection should additionally confirm threshold range, timing, temperature grade, package, and lifecycle requirements.
What can replace the SY88703VKI?
A valid drop-in replacement for the SY88703VKI must match its 10-pin MSOP pinout, 3.3V or 5V supply operation, PECL interface, 622-Mbps capability, enable behavior, and loss-of-signal function. No confirmed pin-compatible substitute was identified in the available cross-reference results. Use the Request a Quote form on this page to ask about exact-MPN sourcing and lifecycle support.
What is the best drop-in replacement for the SY88703VKI?
The SY88703VKI should be replaced only by a device with the same 10-pin MSOP footprint and matching PECL, enable, and loss-of-signal functions. A package match alone is insufficient because threshold programming, propagation timing, supply behavior, and receiver signal levels must also agree. No manufacturer-confirmed cross-brand drop-in candidate was identified, so validate any proposed substitute against the original Microchip Technology datasheet.
Is the SY88703VKI the same as SY88703VKC?
The SY88703VKC name appears in the manufacturer-datasheet indexing for the SY88703V family, while SY88703VKI is the ordered Microchip Technology part number presented here. The published device description identifies both with the 3.3V or 5V, 622-Mbps PECL limiting post-amplifier function. The orderable suffix, temperature grade, and package details must be checked before treating them as interchangeable.
Where can I buy SY88703VKI online?
The SY88703VKI can be requested through the Request a Quote form on this page. The form is the appropriate route for an exact 10-pin MSOP order, current stock status, lead time, and commercial terms. Because this product can also be referenced under family and ordering-suffix names, provide the complete SY88703VKI part number and required quantity with the request.
What is the price of SY88703VKI?
The current commercial price for SY88703VKI should be obtained through the Request a Quote form on this page. The form allows the quantity, target date, and package requirements to be included in the request. This approach avoids applying an obsolete or non-authoritative market figure to an exact-MPN order and provides a directly actionable quotation.
What is the lead time and stock status for SY88703VKI?
Request the current lead time and stock status for SY88703VKI through the Request a Quote form on this page. Include the required quantity, delivery date, and whether the 10-pin MSOP device is for prototype or production use. The distributor listing confirms that the exact part is cataloged, but it does not provide a dependable current lead-time value for every order configuration.
Does the SY88703VKI meet RoHS or AEC-Q100 requirements?
The SY88703VKI's RoHS, REACH, and automotive qualification status must be confirmed from the applicable Microchip Technology product documentation before production release. RoHS and REACH are not numerical electrical specifications, while AEC-Q100 applies only to automotive-qualified variants. Use the manufacturer ordering information or the Request a Quote form on this page to obtain documentation for the exact suffix.

Engineering reference data for SY88703VKI — comparison, design guidance, and compliance information.

Selection Guide

Choose the SY88703VKI for a fiber-optic receiver or related PECL interface that operates at up to 622 Mbps and requires a 3.3V or 5V single supply. It is particularly useful when the design needs a TTL enable function, a chatter-free loss-of-signal indication, and a programmable loss threshold in addition to differential PECL outputs. The device is not a general-purpose analog amplifier and should follow a suitable TIA or signal source. Before selecting a substitute, verify the exact 10-pin MSOP footprint, supply range, PECL levels, enable polarity, LOS behavior, propagation delay, jitter, temperature grade, and availability. No confirmed pin-compatible substitute is listed on this page, which avoids presenting a merely similar amplifier as a safe drop-in replacement.

Comparison with Alternatives

Parameter This Product
Manufacturer Microchip Technology
Package 10-pin MSOP, 3.00 mm width
Product Type Low-power limiting post amplifier
Supply Voltage 3.3V or 5V
Maximum Data Rate 622 Mbps
Data Output Logic Differential PECL
Loss-of-Signal Output Chatter-free TTL with programmable level
Enable Input TTL-compatible
Number of Data Outputs 2 outputs
Supply Configuration Single supply

Key Differentiators

  • Integrated receiver supervision (vs Generic PECL limiting amplifier)
  • Single-supply flexibility (vs 5V-only PECL post amplifier)
  • Differential high-speed output (vs Single-ended limiting stage)

Design Notes

Place the SY88703VKI close to the driving transimpedance amplifier and keep the PECL output routes short. Use the manufacturer's recommended PECL termination network, connect the two complementary outputs as a controlled-impedance pair, and avoid routing them adjacent to high-current switching nodes. At 622 Mbps, trace geometry and return-path continuity are as important as nominal logic compatibility.

Decouple the 3.3V or 5V supply close to the device using the capacitance and placement specified in the manufacturer application circuit. Place the low-impedance ceramic capacitor at the supply and ground pins rather than several centimeters away, and keep the return current beneath or directly adjacent to the high-speed traces. Verify the selected supply level against the PECL output thresholds and input-enable requirements.

Do not treat the SY88703VKI as a substitute for the optical TIA. The TIA supplies gain and converts photocurrent to voltage, while the SY88703VKI limits that output and creates PECL-level waveforms. Set the programmable loss-of-signal threshold against the receiver's normal amplitude range and noise level; an incorrect threshold can cause false loss indications or hide an actual link failure.

Check propagation delay, jitter, rise time, fall time, and output-level margins against the receiver system's timing requirements. The presence of two PECL outputs does not eliminate the need for a return-path and impedance-control review. Confirm that any receiver IC supports the generated PECL levels at the chosen 3.3V or 5V supply and that unused enable or LOS functions are connected appropriately.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

The available product information does not state exact compliance status for the SY88703VKI ordering suffix. Obtain the applicable Microchip Technology product and material declarations before production release.

Data verified on: 2026-11-20 — data verified and curated by XAIPART's component engineering team

Related Searches

SY88703VKI datasheet SY88703VKI pinout SY88703VKI datasheet pdf SY88703VKI equivalent SY88703VKI replacement SY88703VKI cross reference SY88703VKI price SY88703VKI stock Microchip SY88703VKI SY88703VKI 622Mbps PECL amplifier SY88703VKI MSOP-10 SY88703VKI fiber optic receiver SY88703VKI loss of signal SY88703VKI 3.3V 5V

Related Components & Terms

Microchip Technology Micrel Semiconductor SY88703VKI SY88703V SY88703VKC SY88703VKI-TR limiting post amplifier fiber-optic receiver transimpedance amplifier TIA PECL TTL loss of signal programmable LOS threshold clock and data recovery 622 Mbps 3.3V power supply 5V power supply 10-pin MSOP surface-mount package differential signaling optical communication module chatter-free LOS output semiconductor
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details