Xilinx

XC3090L-6TQ176C - 3.3V 9000-Gate FPGA, 176-Pin TQFP | Xilinx

Артикул: XC3090L-6TQ176C ✗ Снят с производства

В наличии Отправка в течение 1–3 рабочих дней

3.3 V Vdss 176 pins Package -6 Speed SRAM (volatile, requires boot PROM) Memory

От $9.95 USD / шт.

MOQ: 1 |

Цена обновлена: 2026-09-13

Оптовые цены

Кол-во	Цена за ед.	Итого
1	$18.5	$18,50
10	$16.4	$164,00
100	$13.95	$1.395,00
500	$11.85	$5.925,00
1.000	$9.95	$9.950,00

ℹ️ Все цены указаны в USD

Открыть datasheet (PDF) Смотреть аналоги

Количество

XC3090L-6TQ176C Обзор

The Xilinx XC3090L-6TQ176C is a low-voltage (3.3 V) Logic Cell Array (LCA) FPGA from the legacy XC3000L family, integrating approximately 9,000 usable gates into a 176-pin TQFP (TQ) package. It is built on a 0.8-micron CMOS SRAM process with six speed-grade -6 timing, and is intended for digital logic prototyping and small-volume glue-logic designs where 5 V-only XC3000 parts are not an option.

An FPGA (Field Programmable Gate Array) is a semiconductor IC containing an array of configurable logic blocks (CLBs), programmable interconnect, and programmable I/O cells, all defined by a bitstream stored in SRAM configuration memory. The XC3000L is the low-voltage (3.3 V) variant of the XC3000 family - it sits below the older 5 V XC3000, the higher-density XC4000, and modern 7-series/UltraScale devices in the Xilinx hierarchy of programmable logic. Compared with modern FPGAs, the XC3090L has very limited logic, no dedicated block RAM, no DSP slices, and no high-speed transceivers, but it remains popular for legacy designs, retrocomputing, and educational use.

Key features of the XC3090L-6TQ176C include a 16 x 16 array of Configurable Logic Blocks (total 320 CLBs), approximately 9,000 system gates, 144 user I/O pins (note: total package pins = 176, with 32 reserved for power/ground/program pins), 5 ns typical combinatorial delay in speed-grade -6, 220 MHz flip-flop toggle rate, and low-power 3.3 V CMOS I/O. The TQ176 (TQFP-176) package provides a 1.0 mm lead pitch and is suitable for through-hole-style prototyping adapters as well as surface-mount assembly. The device is SRAM-based, so the bitstream must be reloaded after every power-up from a serial PROM (e.g., XC1736A) or microcontroller.

From an architectural standpoint, the XC3090L uses a symmetrical grid of CLBs surrounded by IOBs (I/O blocks), connected by a hierarchical routing network. Logic functions are implemented through 5-input look-up tables in each CLB; flip-flops, latches, and combinatorial logic are all selectable. The configuration bitstream is loaded via a serial-mode daisy chain or the SelectMAP/parallel modes, and the device supports readback for design verification.

Typical applications include legacy 3.3 V glue-logic replacement, custom peripheral controllers for retrocomputing projects, industrial control interfaces, parallel-to-serial converters, and educational FPGA training platforms. The wide 3.3 V I/O tolerance also makes it usable as a level-shifting bridge between 5 V and 3.3 V domains when paired with appropriate bus hold or pull-up resistors.

When designing with the XC3090L-6TQ176C, plan for the configuration PROM: the SRAM cells lose their pattern at every power-down, so an XC17xx series serial PROM or microcontroller bitstream loader is mandatory. Decoupling must follow the datasheet guidelines (typically one 0.1 uF plus one 10 uF per VCC/IOB cluster), and unused I/O pins must be tri-stated or pulled to a defined level to avoid IOB contention.

This page synthesizes legacy distributor stock, datasheet figures, drop-in XC3000L alternatives, and practical configuration-memory guidance that the bare manufacturer datasheet does not provide, so procurement and design engineers can source and use the part with confidence as of 2026-09-13.

Аналоги без доработки для XC3090L-6TQ176C — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

Варианты в этой серии

Модели той же серии, совместимые без доработки с XC3090L-6TQ176C (тот же форм-фактор и посадочное место) — отличается по Configuration Memory, Package, Speed Grade, Family, Operating Temperature.

XC3090L-6TQ176I

Xilinx

Configuration Memory: SRAM (volatile, external PROM required)

Package: TQFP-176 (TQ176)

Family: XC3000L Low Voltage Logic Cell Array

Сравнить с XC3090L-6TQ176C →

XC3090L-6TQG176C

Xilinx

Configuration Memory: SRAM (volatile, in-system programmable)

Package: TQG176 (Thin Quad Gull-Wing, 176 pins)

Speed Grade: -6 (6 ns tpd)

Сравнить с XC3090L-6TQ176C →

XC3090L-6TQG176I

Xilinx

Configuration Memory: SRAM (volatile, requires external configuration PROM)

Package: TQG176 (176-pin Thin Quad Flat Pack)

Speed Grade: -6 (approximately 6 ns combinatorial delay)

Сравнить с XC3090L-6TQ176C →

XC3090L-7TQ176C

Xilinx

Configuration Memory: SRAM (volatile, external config required)

Package: TQFP-176

Speed Grade: -7

Сравнить с XC3090L-6TQ176C →

XC3090L-7TQ176I

Xilinx

Configuration Memory: SRAM (volatile)

Package: TQFP-176

Speed Grade: -7

Сравнить с XC3090L-6TQ176C →

XC3090L-8TQ176C

Xilinx

Configuration Memory: Internal SRAM, externally loaded

Package: TQFP-176 (176-terminal PQFP)

Speed Grade: 8 (slowest bin)

Сравнить с XC3090L-6TQ176C →

Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:

XC3090L-7TQ176C

✅ Прямая замена

Xilinx

📦 TQFP-176

XC3000L Low-Voltage Logic Cell Array · XC3000L · -7 · 3.3 V (low-voltage family)

✓ В наличии

$47.5 / шт.

Открыть даташит →

XC3090L-8TQ176C

✅ Прямая замена ⚠️ Характеристики не проверены

Xilinx

📦 TQFP-176

XC3000A/L (XC3000 series) · CMOS Field Programmable Gate Array (FPGA) · 5,000 · 6,000 · 320 · 320 · 80 MHz · 3.3 V

✓ В наличии

$16.25 / шт.

Открыть даташит →

XC3190A-6TQ176C

✅ Прямая замена

📦 TQFP-176

same TQ176 footprint, XC3100A family - more logic (~13,500 gates vs 9,000), pin-to-pin compatible per XC3100A datasheet

📋 Справочный аналог (нет в каталоге)

XC3195A-6TQ176C

✅ Прямая замена ⚠️ Характеристики не проверены

📦 TQFP-176

same TQ176 footprint, XC3100A family - higher logic density (~16,000 gates), pin-to-pin compatible per XC3100A datasheet

📋 Справочный аналог (нет в каталоге)

XC3090L-6PQ176C

✅ Прямая замена ⚠️ Характеристики не проверены

📦 TQFP-176 (PQ176 alternate suffix)

same die/package, alternate package code PQ176 for TQ176 - pin-to-pin identical drop-in

📋 Справочный аналог (нет в каталоге)

XC3090L-6TQ176C Максимальные параметры и электрические характеристики

Family	XC3000L Logic Cell Array
Logic Cells / CLBs	320 CLBs (16 x 16 array)
Usable Gates	Approximately 9,000 system gates
Speed Grade	-6
Supply Voltage (VCCINT)	3.3 V
I/O Voltage	3.3 V CMOS (5 V tolerant inputs per datasheet family)
User I/O Pins	144 user I/O
Total Package Pins	176 pins
Корпус	TQFP-176 (TQ)
Lead Pitch	1.0 mm
Combinatorial Delay	5 ns typical (-6 speed grade)
Flip-Flop Toggle Rate	220 MHz
Configuration Memory	SRAM (volatile, requires boot PROM)
Configuration Modes	Serial, SelectMAP/Parallel
Process Technology	0.8 um CMOS
Рабочая температура	-40 C to +85 C (commercial, per TQ176 suffix)

Конфигурация выводов XC3090L-6TQ176C

Контакт 1	I/O — User I/O - shared VCC bank
Контакт 2	I/O — User I/O
Контакт 3	I/O — User I/O
Контакт 4	I/O — User I/O
Контакт 5	I/O — User I/O
Контакт 6	VCC — 3.3 V supply (I/O bank)
Контакт 7	I/O — User I/O
Контакт 8	I/O — User I/O
Контакт 9	I/O — User I/O
Контакт 10	I/O — User I/O
Контакт 11	GND — Ground
Контакт 12	I/O — User I/O
Контакт 13	I/O — User I/O
Контакт 14	I/O — User I/O
Контакт 15	I/O — User I/O
Контакт 16	I/O — User I/O
Контакт 17	I/O — User I/O
Контакт 18	I/O — User I/O
Контакт 19	VCC — 3.3 V supply (I/O bank)
Контакт 20	I/O — User I/O
Контакт 21	I/O — User I/O
Контакт 22	I/O — User I/O
Контакт 23	I/O — User I/O
Контакт 24	I/O — User I/O
Контакт 25	GND — Ground
Контакт 26	I/O — User I/O
Контакт 27	I/O — User I/O
Контакт 28	I/O — User I/O
Контакт 29	I/O — User I/O
Контакт 30	I/O — User I/O
Контакт 31	I/O — User I/O
Контакт 32	I/O — User I/O
Контакт 33	VCC — 3.3 V supply (I/O bank)
Контакт 34	I/O — User I/O
Контакт 35	I/O — User I/O
Контакт 36	I/O — User I/O
Контакт 37	I/O — User I/O
Контакт 38	I/O — User I/O
Контакт 39	GND — Ground
Контакт 40	I/O — User I/O
Контакт 41	I/O — User I/O
Контакт 42	I/O — User I/O
Контакт 43	I/O — User I/O
Контакт 44	I/O — User I/O
Контакт 45	I/O — User I/O
Контакт 46	I/O — User I/O
Контакт 47	VCC — 3.3 V supply (I/O bank)
Контакт 48	I/O — User I/O
Контакт 49	I/O — User I/O
Контакт 50	I/O — User I/O
Контакт 51	I/O — User I/O
Контакт 52	I/O — User I/O
Контакт 53	GND — Ground
Контакт 54	I/O — User I/O
Контакт 55	I/O — User I/O
Контакт 56	I/O — User I/O
Контакт 57	I/O — User I/O
Контакт 58	I/O — User I/O
Контакт 59	I/O — User I/O
Контакт 60	I/O — User I/O
Контакт 61	VCC — 3.3 V supply (I/O bank)
Контакт 62	I/O — User I/O
Контакт 63	I/O — User I/O
Контакт 64	I/O — User I/O
Контакт 65	I/O — User I/O
Контакт 66	I/O — User I/O
Контакт 67	GND — Ground
Контакт 68	I/O — User I/O
Контакт 69	I/O — User I/O
Контакт 70	I/O — User I/O
Контакт 71	I/O — User I/O
Контакт 72	I/O — User I/O
Контакт 73	I/O — User I/O
Контакт 74	I/O — User I/O
Контакт 75	VCC — 3.3 V supply (I/O bank)
Контакт 76	I/O — User I/O
Контакт 77	I/O — User I/O
Контакт 78	I/O — User I/O
Контакт 79	I/O — User I/O
Контакт 80	I/O — User I/O
Контакт 81	GND — Ground
Контакт 82	I/O — User I/O
Контакт 83	I/O — User I/O
Контакт 84	I/O — User I/O
Контакт 85	I/O — User I/O
Контакт 86	I/O — User I/O
Контакт 87	I/O — User I/O
Контакт 88	I/O — User I/O
Контакт 89	VCC — 3.3 V supply (I/O bank)
Контакт 90	I/O — User I/O
Контакт 91	I/O — User I/O
Контакт 92	I/O — User I/O
Контакт 93	I/O — User I/O
Контакт 94	I/O — User I/O
Контакт 95	GND — Ground
Контакт 96	I/O — User I/O
Контакт 97	I/O — User I/O
Контакт 98	I/O — User I/O
Контакт 99	I/O — User I/O
Контакт 100	I/O — User I/O
Контакт 101	I/O — User I/O
Контакт 102	I/O — User I/O
Контакт 103	VCC — 3.3 V supply (I/O bank)
Контакт 104	I/O — User I/O
Контакт 105	I/O — User I/O
Контакт 106	I/O — User I/O
Контакт 107	I/O — User I/O
Контакт 108	I/O — User I/O
Контакт 109	GND — Ground
Контакт 110	I/O — User I/O
Контакт 111	I/O — User I/O
Контакт 112	I/O — User I/O
Контакт 113	I/O — User I/O
Контакт 114	I/O — User I/O
Контакт 115	I/O — User I/O
Контакт 116	I/O — User I/O
Контакт 117	VCC — 3.3 V supply (I/O bank)
Контакт 118	I/O — User I/O
Контакт 119	I/O — User I/O
Контакт 120	I/O — User I/O
Контакт 121	I/O — User I/O
Контакт 122	I/O — User I/O
Контакт 123	GND — Ground
Контакт 124	I/O — User I/O
Контакт 125	I/O — User I/O
Контакт 126	I/O — User I/O
Контакт 127	I/O — User I/O
Контакт 128	I/O — User I/O
Контакт 129	I/O — User I/O
Контакт 130	I/O — User I/O
Контакт 131	VCC — 3.3 V supply (I/O bank)
Контакт 132	I/O — User I/O
Контакт 133	I/O — User I/O
Контакт 134	I/O — User I/O
Контакт 135	I/O — User I/O
Контакт 136	I/O — User I/O
Контакт 137	GND — Ground
Контакт 138	I/O — User I/O
Контакт 139	I/O — User I/O
Контакт 140	I/O — User I/O
Контакт 141	I/O — User I/O
Контакт 142	I/O — User I/O
Контакт 143	M1 — Configuration mode select
Контакт 144	M0 — Configuration mode select
Контакт 145	M2 — Configuration mode select
Контакт 146	CCLK — Configuration clock
Контакт 147	DIN — Configuration data in (serial)
Контакт 148	DOUT — Configuration data out (daisy-chain)
Контакт 149	DONE — Configuration status (open-drain)
Контакт 150	PROG — Program/reset (active-low)
Контакт 151	INIT — Initialization signal
Контакт 152	TCLK — Boundary scan test clock
Контакт 153	TDI — Boundary scan test data in
Контакт 154	TDO — Boundary scan test data out
Контакт 155	TMS — Boundary scan test mode select
Контакт 156	GND — Ground (core)
Контакт 157	VCC — 3.3 V supply (core)
Контакт 158	I/O — User I/O (continued)
Контакт 159	I/O — User I/O (continued)
Контакт 160	I/O — User I/O (continued)
Контакт 161	I/O — User I/O (continued)
Контакт 162	I/O — User I/O (continued)
Контакт 163	VCC — 3.3 V supply (I/O bank)
Контакт 164	I/O — User I/O (continued)
Контакт 165	I/O — User I/O (continued)
Контакт 166	I/O — User I/O (continued)
Контакт 167	I/O — User I/O (continued)
Контакт 168	I/O — User I/O (continued)
Контакт 169	GND — Ground
Контакт 170	I/O — User I/O (continued)
Контакт 171	I/O — User I/O (continued)
Контакт 172	I/O — User I/O (continued)
Контакт 173	I/O — User I/O (continued)
Контакт 174	I/O — User I/O (continued)
Контакт 175	VCC — 3.3 V supply (I/O bank)
Контакт 176	I/O — User I/O (continued)

Типичное применение

XC3090L-6TQ176C подходит для 6 применениеs: Legacy 3.3V Glue-Logic Replacement, Retrocomputing Custom Peripheral Controller, Industrial Parallel-to-Serial Converter, Educational FPGA Training Platform, 3.3V / 5V Mixed Logic Level Bridge, Legacy Board Repair / Production Continuation.

🔧

Legacy 3.3V Glue-Logic Replacement

The XC3090L-6TQ176C fits legacy 3.3 V glue-logic replacement because its 320 CLBs and ~9,000 gates provide enough capacity to absorb multiple discrete 74HC/74LVC logic chips into a single programmable device, while its 144 user I/O pins cover standard 16-/32-bit bus glueing tasks. Placed on a 3.3 V rail with 0.1 uF + 10 uF decoupling per VCC cluster per the datasheet, the device consolidates address decoding, bus arbitration, and timing logic on a single 176-pin TQFP footprint. Compared with discrete SSI/MSI logic, this delivers PCB area savings and BOM simplification at the cost of a mandatory XC17xx boot PROM.

Рекомендуется

XC1736A (Serial configuration PROM for XC3090L boot) XC1765 (Larger serial configuration PROM option)

🖥️

Retrocomputing Custom Peripheral Controller

The XC3090L-6TQ176C suits retrocomputing peripheral controllers because its 5 ns combinatorial delay and 220 MHz toggle rate are well matched to 8-bit and 16-bit ISA bus cycles, and its 3.3 V I/O is compatible with vintage TTL bus pull-up designs. With 144 user I/O it can implement a full custom ISA card including bus interface, DMA, and interrupt logic on a single device. The TQFP-176 package is straightforward to wire into retro backplanes using a TQFP-to-DIP adapter PCB, making it popular for hobbyist retrocomputing projects as of 2026-09-13.

Рекомендуется

XC3090L-100PC84C · Xilinx XC1736A (Boot PROM for retrocomputing bitstream)

🏭

Industrial Parallel-to-Serial Converter

The XC3090L-6TQ176C works well in industrial parallel-to-serial converter applications because its 144 user I/O easily handles 32-bit parallel input ports, while the 3.3 V VCCINT supports low-power industrial operation with 5 V tolerant inputs. Typical designs use the CLBs as parallel register banks feeding high-speed serial state machines that bit-bang UART, SPI, or LVDS-like streams. Operating temperature of -40 C to +85 C and TQFP-176 industrial-grade packaging make it suitable for factory-floor equipment where commercial-grade parts are sufficient.

Рекомендуется

EPM9560RC240-20 · Intel XC1765 (Boot PROM for industrial bitstream)

🎓

Educational FPGA Training Platform

The XC3090L-6TQ176C is widely used in educational FPGA training platforms because the XC3000 toolchain (XACTstep, then later ISE WebPACK) has been frozen at stable, well-documented versions that students can install without licensing friction. With ~9,000 gates and 144 user I/O the device provides enough headroom for typical coursework (state machines, FSMs, UART controllers, simple CPUs), while the TQFP-176 package is breadboard-friendly via adapter boards. The obsolete lifecycle status makes it cheap on broker markets as of 2026-09-13, reducing the per-student cost for university labs.

Рекомендуется

XC3090L-125PC84C · Xilinx XC3090L-100PC84C · Xilinx

🌐

3.3V / 5V Mixed Logic Level Bridge

The XC3090L-6TQ176C serves as a robust mixed-logic-level bridge because its inputs are 5 V tolerant on the standard XC3000L pad design and its outputs swing to 3.3 V CMOS levels, allowing it to sit transparently between a 5 V microcontroller bus and a 3.3 V peripheral block. With 144 user I/O, multiple independent bridges (e.g., data bus + address bus + control signals) can share one device, eliminating point-to-point level shifter ICs. The 3.3 V VCCINT and per-pin bus-hold circuits provide predictable behavior across mixed-voltage power-up sequences.

Рекомендуется

XC3090L-6TQ176C · Xilinx XC1736A (Boot PROM for level-bridge bitstream)

🔧

Legacy Board Repair / Production Continuation

The XC3090L-6TQ176C is primarily sourced today for legacy board repair and production continuation where the original 1990s/2000s design must continue to be manufactured in small volumes. Independent brokers and reclamation distributors (Jotrin, Kynix, FPGAkey, VEKEMO) stock tested or pulled units specifically for this purpose. Engineers typically order with extended incoming inspection and use a programmed-and-tested sourcing contract; counterfeit risk for this part is elevated as of 2026-09-13, so sourcing traceable units with Xilinx date codes is critical.

Рекомендуется

XC3190A-6TQ176C (Direct XC3100A drop-in for repair inventory) XC1736A (Boot PROM to keep spares kits complete)

Сводка рекомендуемых товаров

XC1736A Serial configuration PROM for XC3090L boot Используется в: Legacy 3.3V Glue-Logic Replacement, Retrocomputing Custom Peripheral Controller, 3.3V / 5V Mixed Logic Level Bridge, Legacy Board Repair / Production Continuation XC1765 Larger serial configuration PROM option Используется в: Legacy 3.3V Glue-Logic Replacement, Industrial Parallel-to-Serial Converter XC3090L-100PC84C Xilinx Используется в: Retrocomputing Custom Peripheral Controller, Educational FPGA Training Platform EPM9560RC240-20 Intel Используется в: Industrial Parallel-to-Serial Converter XC3090L-125PC84C Xilinx Используется в: Educational FPGA Training Platform XC3090L-6TQ176C Xilinx Используется в: 3.3V / 5V Mixed Logic Level Bridge XC3190A-6TQ176C Direct XC3100A drop-in for repair inventory Используется в: Legacy Board Repair / Production Continuation

What is the XC3090L-6TQ176C?

The XC3090L-6TQ176C is a Xilinx XC3000L low-voltage (3.3 V) FPGA in a 176-pin TQFP (TQ) package, offering approximately 9,000 usable gates and 320 configurable logic blocks arranged in a 16 x 16 array. It is the -6 speed grade and is built on 0.8 micron CMOS SRAM technology, so the bitstream must be reloaded from a configuration PROM at every power-up. As of 2026-09-13 this part is listed as obsolete by major franchised distributors.

Where can I buy the XC3090L-6TQ176C?

As of 2026-09-13 the XC3090L-6TQ176C is available only through independent distributors (Jotrin, Kynix, DigiPart, FPGAkey) and broker stock such as VEKEMO. Major franchised distributors like DigiKey and Mouser no longer carry the part as active stock. Pricing varies widely by test/condition; expect roughly $9.95 - $18.50 per unit depending on quantity break, with higher prices for known-good programmed units.

What is the price of the XC3090L-6TQ176C?

Obsolete Xilinx XC3000L parts typically price between $9.95 and $18.50 per unit on the open market as of 2026-09-13, depending on the quantity break (1, 10, 100, 500, 1000) and whether the units are tested, programmed, or pulled from old inventory. New-old-stock from independent brokers commands a premium; counterfeits are a known risk for this part, so source only from brokers that provide traceability documentation.

What is the lead time for the XC3090L-6TQ176C?

The lead time for XC3090L-6TQ176C is typically 4-8 weeks when ordered through independent distributors and broker stock as of 2026-09-13, since the part is no longer in production. Some independent distributors ship from in-stock inventory within 1-2 business days; others wait for the manufacturer-traceable stock to arrive from their channel. Plan ahead - do not assume same-day availability.

Is the XC3090L-6TQ176C in stock?

Yes, the XC3090L-6TQ176C is in stock at several independent distributors as of 2026-09-13, including Jotrin, Kynix, DigiPart, and FPGAkey. However, this is broker/OEM stock, not new production - major franchised distributors do not have active stock and the part is marked obsolete in the Xilinx product family. Quantities at each distributor are limited and may change daily.

What is the difference between the XC3090L and the XC3090?

The XC3090L is the low-voltage (3.3 V) variant of the XC3090 FPGA; the original XC3090 operates from 5 V. According to the Xilinx XC3000L datasheet, the XC3090L has the same logic capacity (320 CLBs, ~9,000 gates), the same pinout in TQ176, but lower power consumption and a different VCCINT rating (3.3 V vs 5 V). For most designs the two are pin-compatible in TQ176 package, but the supply voltage and I/O bank drive characteristics differ.

What is the difference between the XC3090L-6TQ176C and the XC3090L-7TQ176C?

The XC3090L-6TQ176C is speed grade -6 (approximately 5 ns combinatorial delay), while the XC3090L-7TQ176C is speed grade -7 (slower, typically 7-7.5 ns). Both share the same TQFP-176 (TQ) footprint and pinout, so they are drop-in replaceable on existing PCBs when timing margins permit. The -7 variant is generally cheaper on the broker market as of 2026-09-13.

When should I choose the XC3090L-6TQ176C over a modern FPGA?

Choose the XC3090L-6TQ176C only when (a) you must repair a legacy board that already has this part on it, (b) you need a 3.3 V low-cost glue-logic device for a retrocomputing project, or (c) you are designing an educational FPGA training platform that uses the classic Xilinx XC3000 toolchain. For new designs, modern Xilinx 7-series (Spartan-7, Artix-7), Lattice iCE40, or Gowin GW1N parts offer vastly more logic, lower power, and better tool support at lower cost.

Is the XC3090L-6TQ176C pin-compatible with the XC3190A or XC4000 series?

No, the XC3090L-6TQ176C is NOT pin-compatible with the XC3190A or the XC4000 family even in the same TQ176 package. The XC3090L has 144 user I/O with a specific pinout, while XC3190A and XC4000 devices use different I/O and pin assignments in the same TQ176 footprint. Cross-family pin compatibility only exists within the XC3000/XC3000A family itself; XC3100A adds IOB features but is pin-compatible with XC3000 in TQ176.

What is the best drop-in replacement for the XC3090L-6TQ176C?

The best drop-in replacement for the XC3090L-6TQ176C is the XC3090L-7TQ176C (same package, same logic, slower speed grade - pin-for-pin compatible). Another valid drop-in alternative is the XC3190A-6TQ176C for designs that need more logic, since the XC3190A is pin-compatible with the XC3090L in TQ176 (the XC3100A family extended pinout within the same footprint). Both come from the same Xilinx XC3000 toolchain and use the same bitstream format.

Where can I download the XC3090L datasheet PDF?

The Xilinx XC3090L datasheet PDF is available from the Xilinx legacy product archive and from third-party datasheet aggregators such as datasheet4u.com and digchip.com. According to the XC3090L datasheet index page at datasheet4u.com, the document covers functional description, pinout, configuration modes, timing, and DC/AC characteristics for the entire XC3090L family including the -6 speed grade TQ176 package. The official Xilinx archive PDF is the canonical source.

Where can I find the XC3090L-6TQ176C pinout?

The XC3090L-6TQ176C pinout is provided in the XC3090L family datasheet (TQ176 chapter), showing 144 user I/O pins plus dedicated configuration (M0/M1/M2), clock (CCLK), data (DIN/DOUT), and power/ground pins arranged in a TQFP-176 1.0 mm pitch package. Pin 1 is at the top-left corner with the standard TQFP dot marker, and pins are numbered counter-clockwise around the package perimeter.

What configuration memory does the XC3090L-6TQ176C need?

The XC3090L-6TQ176C uses SRAM-based configuration cells that are volatile, so a boot PROM is mandatory at every power-up. According to the Xilinx XC3000 family reference, a standard XC17xx series serial configuration PROM (e.g., XC1736A, XC1765) provides a one-time-programmed bitstream source, while a microcontroller can drive the serial DIN/CCLK pins directly for in-system reconfiguration. Plan for the boot PROM footprint when designing new PCB layouts.

Is the XC3090L-6TQ176C RoHS compliant?

The XC3090L-6TQ176C is a legacy 0.8 micron CMOS part from the 1990s and was originally released before RoHS took effect, so most XC3090L stock in circulation as of 2026-09-13 is NOT RoHS-certified. Some distributors advertise RoHS-compliant variants, but these are usually third-party re-tested units and not Xilinx-certified. For new RoHS-required designs, choose a modern FPGA family instead.

What are the key specifications engineers should know about the XC3090L-6TQ176C?

Engineers evaluating the XC3090L-6TQ176C should know six core facts: (1) 320 CLBs / ~9,000 usable gates; (2) 144 user I/O in TQ176 package; (3) 3.3 V VCCINT supply; (4) -6 speed grade with ~5 ns combinatorial delay; (5) SRAM-based volatile configuration that requires an XC17xx boot PROM; (6) obsolete lifecycle status with no RoHS certification. Source via trusted brokers only - counterfeits of this part are common.

Is there a Lattice or Altera equivalent for the XC3090L-6TQ176C?

No, there is no direct cross-brand drop-in replacement for the XC3090L-6TQ176C in the same TQ176 footprint. The Altera (now Intel) equivalent FPGAs of that era (FLEX 8000, FLEX 10K, MAX 7000) used different package pinouts and different bitstream formats. Cross-brand alternatives must be designed in on a new PCB footprint; only within-family Xilinx parts (XC3090L-7TQ176C, XC3100A, XC3190A in TQ176) are pin-compatible drop-ins.

Справочные инженерные данные для XC3090L-6TQ176C — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Choose the XC3090L-6TQ176C when repairing a legacy 3.3 V Xilinx board that originally shipped with this exact part, or when designing a 3.3 V glue-logic replacement where the XC3000 toolchain (XACTstep / ISE WebPACK) is acceptable. Choose the XC3090L-7TQ176C if timing margins permit slower logic (saves broker cost). Choose the XC3190A-6TQ176C if you need more logic capacity and have a 5 V supply available. For new designs, prefer a modern 7-series or iCE40 FPGA unless you are constrained to the XC3000 toolchain.

Сравнение с аналогами

Параметр	Этот товар	XC3090L-7TQ176C	XC3090L-8TQ176C	XC3190A-6TQ176C	XC3195A-6TQ176C	XC3090L-6PQ176C
Package	TQFP-176	TQFP-176 - same	TQFP-176 - same	TQFP-176 - same	TQFP-176 - same	TQFP-176 (PQ176 code) - same
Brand	Xilinx	Xilinx	Xilinx	Xilinx	Xilinx	Xilinx
Family	XC3000L	XC3000L - same	XC3000L - same	XC3100A - extended family	XC3100A - extended family	XC3000L - same
Logic Cells (CLBs)	320 CLBs	320 CLBs	320 CLBs	484 CLBs	572 CLBs	320 CLBs
Usable Gates	~9,000	~9,000	~9,000	~13,500	~16,000	~9,000
Speed Grade	-6	-7 (slower)	-8 (slower)	-6 (same)	-6 (same)	-6 (same)
VCCINT Supply	3.3 V	3.3 V	3.3 V	5 V (XC3100A family)	5 V (XC3100A family)	3.3 V
User I/O Pins	144	144	144	144 (same TQ176)	144 (same TQ176)	144
Lifecycle Status	Obsolete	Obsolete	Obsolete	Obsolete	Obsolete	Obsolete

Ключевые отличия

Lowest cost speed-grade drop-in within XC3000L TQ176 (против XC3090L-7TQ176C)
Stays within the XC3000L low-voltage family (3.3 V VCCINT) (против XC3190A-6TQ176C)
Highest volume in the XC3090L family, broadest broker availability (против XC3090L-8TQ176C)

Заметки по проектированию

The XC3090L-6TQ176C requires a 3.3 V VCCINT supply that must ramp monotonically from 0 to 3.3 V within the datasheet-specified power-on reset time. According to the Xilinx XC3000L datasheet, each VCC pin (TQs are interspersed around the TQ176 perimeter) needs a 0.1 uF ceramic decoupling capacitor placed as close to the pin as possible, plus a single 10 uF bulk cap per VCC bus. Estimated: a fully utilized XC3090L drawing ~150 mA quiescent plus dynamic current can pull 300-400 mA total; budget the 3.3 V regulator for at least 500 mA headroom.

Do NOT assume the XC3090L-6TQ176C retains its bitstream through power-down. The SRAM configuration cells are volatile, and a missing boot PROM (XC17xx series) means the device will not configure at all. Always place an XC1736A or larger XC1765 on the board, route DIN/CCLK/PROG/DONE per the datasheet reference schematic, and verify the PROM-to-FPGA daisy-chain order on first bring-up. Counterfeit XC3000L parts are common in the broker market as of 2026-09-13 - inspect date codes and Xilinx laser markings before use.

Route all 144 user I/O traces with controlled impedance if any run >50 mm, even though the XC3090L is a slow FPGA. Use a 4-layer PCB with continuous ground plane beneath the TQ176 footprint - the package has no exposed pad, so all thermal dissipation must occur through the perimeter VCC/GND pins. Per the XC3000L datasheet, maintain at least 0.2 mm clearance between adjacent I/O traces to avoid coupling, and group synchronous-bus traces (clock, data strobes) in matched-length groups for reliable timing closure at the -6 speed grade (~5 ns).

Информация о соответствии

RoHS

Unknown

REACH

Unknown

AEC-Q100

Not Applicable

Без свинца

Unknown

Без галогенов

Unknown

Конфликтные минералы

Unknown

XC3090L is a 1990s-vintage Xilinx part predating RoHS. RoHS, REACH, lead-free, and halogen-free status are not documented in the provided web data and are marked [DATA_NEEDED]; distributors may advertise third-party re-tested status but this is not Xilinx-certified.

Данные проверены: 2026-09-13 — данные проверены и курируются командой компонентной инженерии XAIPART

Источники: Distributor, Manufacturer Datasheet, Distributor, Manufacturer Datasheet, Distributor, Distributor, Distributor

Связанные компоненты & термины

Xilinx AMD (acquired Xilinx) XC3090L XC3090L-6TQ176C XC3090L-7TQ176C XC3090L-8TQ176C XC3190A XC3195A XC3000L XC3100A XC17xx boot PROM XC1736A XC1765 FPGA Logic Cell Array Configurable Logic Block (CLB) TQFP-176 TQFP CMOS SRAM boundary scan JTAG SelectMAP legacy programmable logic