MAX232AEWE+T - +5V 2/2 RS-232 Transceiver | Analog Devices
MPN: MAX232AEWE+T ✓ AktifMAX232AEWE+T Genel Bakış
An RS-232 transceiver is an interface IC that translates between single-ended, bipolar RS-232 signals and logic-level digital signals. The receiver converts an RS-232 input into a CMOS-compatible logic level, while the driver converts a logic-level input into an RS-232 output. In the broader hierarchy, the MAX232AEWE+T is an interface transceiver, a communication IC, and a semiconductor designed to bridge a host UART and an RS-232 physical layer.
The device provides two driver channels and two receiver channels in one package. Its +5 V supply arrangement simplifies use in conventional +5 V embedded systems, while integrated level translation eliminates separate RS-232 line drivers and receivers. The MAX232A designation also identifies a higher-slew-rate implementation intended for RS-232 applications requiring improved transition behavior compared with the base MAX232 family.
The MAX232AEWE+T is suitable for EIA/TIA-232E and V.28/V.24 communication interfaces. Its 16-SOIC package permits conventional surface-mount assembly and provides enough pins for two transmit channels, two receive channels, supply connections, ground, and the internal charge-pump components. Because RS-232 is a single-ended interface, the supply and signal-return ground path must be managed carefully in systems with long cables or significant ground-potential differences.
Typical applications include industrial serial consoles, point-of-sale equipment, data-acquisition systems, embedded control boards, and legacy peripheral connections. It can connect a UART-equipped microcontroller, DSP, or field-programmable logic device to an RS-232 port while limiting the design to one interface IC rather than separate line-driver and receiver packages.
PCB implementation should follow the charge-pump capacitor requirements and layout guidance in the manufacturer datasheet. Place the required capacitors close to their associated pins, maintain a continuous ground reference, and route the RS-232 cable-side traces away from sensitive digital and analog nets. Verify the complete interface against the intended baud rate, cable length, and grounding topology before production release.
This product page combines the MAX232AEWE+T family specifications with same-package alternatives, application guidance, and design notes intended to help engineers select and implement the interface efficiently.
Drop-in alternatifler için MAX232AEWE+T — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller MAX232AEWE+T (aynı form faktörü ve ayağa oturma) — farklı olan Package, Product Type, Interface Standard, Maximum Data Rate, Supply Voltage.
MAX232EWE+T
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →MAX232EIDWR
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →MAX232ECDWR
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →MAX232EEWE+T
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →MAX232AEWE+T Özellikler
| Product Type | RS-232 transceiver |
| Driver and Receiver Configuration | 2/2 transceiver |
| Besleme Gerilimi | +5 V |
| Number of Drivers | 2 channels |
| Number of Receivers | 2 channels |
| Interface Standard | EIA/TIA-232E and V.28/V.24 |
| Paket | 16-SOIC |
| Montaj Türü | Surface mount |
| Slew Rate | Higher-slew-rate MAX232A implementation |
| Manufacturer Orderable Packaging | Tape and reel |
MAX232AEWE+T 16-soic Pin Yapısı Kılavuzu
MAX232AEWE+T (16-soic paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.
Ayrıntılı pin çıkış verisi mevcut değil: MAX232AEWE+T.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
MAX232AEWE+T için uygundur 6 uygulamas: Industrial Serial Console, Point-of-Sale Terminal Interface, Data-Acquisition Equipment, Embedded Control Board, Legacy Peripheral Connectivity, Instrumentation Control Link.
Industrial Serial Console
The MAX232AEWE+T fits an industrial controller that needs to expose a UART through an RS-232 service or console connector. Its 2/2 organization allows one transmit and one receive path for console traffic while leaving a second driver-receiver pair available for a second RS-232 function. The +5 V supply matches a conventional embedded control board, and the 16-SOIC footprint simplifies assembly alongside the host processor. Because a long cable can introduce ground-potential differences and electrostatic discharge, retain the transceiver close to the connector and add protection appropriate to the installation. Confirm the required temperature grade, baud rate, logic thresholds, and external capacitor network against the Analog Devices MAX232A data sheet.
Önerilen
Point-of-Sale Terminal Interface
A point-of-sale terminal can use the MAX232AEWE+T to connect a logic-level UART to a legacy RS-232 peripheral such as a reader, printer interface, or service connector. The two-driver and two-receiver arrangement supports full-duplex communication and permits two RS-232 ports when the board requires more than one cable connection. Running from +5 V avoids a separate translator supply rail, while integrated level conversion reduces the number of discrete interface components. The MAX232A family's higher slew rate is relevant when the selected interface emphasizes transition performance. Place the IC near the connector, route driver outputs as a separate group, and use a continuous board ground as the signal reference.
Önerilen
Data-Acquisition Equipment
The MAX232AEWE+T is appropriate for data-acquisition equipment that must communicate with a host computer through RS-232. A controller or FPGA can drive the transmit input while receiving commands or measurements through a receiver channel, eliminating the need for separate RS-232 line devices. The 2/2 channel count can support a control link and a separate data or status link. The +5 V supply is convenient for legacy acquisition hardware, and the 16-SOIC package provides a conventional surface-mount footprint. Keep analog input circuitry and sensitive sensor references away from the RS-232 outputs, and use the manufacturer's recommended capacitor values and grounding arrangement to preserve signal integrity.
Önerilen
Embedded Control Board
The MAX232AEWE+T adds a conventional RS-232 port to an embedded control board built around a microcontroller, DSP, or programmable logic device. The processor UART connects directly to the transceiver's logic-side signals, while the driver and receiver outputs connect to the external RS-232 connector. Its +5 V operation supports established embedded power architectures, and the 16-SOIC package allows assembly without a specialized fine-pitch footprint. Design the connector-side protection network around the cable environment, and confirm the logic-level input thresholds and output drive capability for the selected host device. The manufacturer data sheet's charge-pump capacitor placement and application circuit should be followed closely.
Önerilen
Legacy Peripheral Connectivity
The MAX232AEWE+T provides a practical bridge to legacy RS-232 peripherals when a newer controller offers only UART or CMOS logic I/O. It converts the host's logic-level TX and RX signals to and from the bipolar, single-ended RS-232 interface, allowing equipment such as test instruments, service tools, and older industrial peripherals to remain in service. The two-channel transmitter and receiver arrangement can support more than one cable or leave spare channels for future expansion. Use the +5 V rail specified for the interface and validate the peripheral's connector wiring and signal polarity. Cable-side protection and a defined ground-reference strategy remain necessary for reliable operation over long or noisy interconnects.
Önerilen
Instrumentation Control Link
The MAX232AEWE+T can serve as the RS-232 control-link interface in laboratory or field instrumentation. A microcontroller may use one transmitter and one receiver for commands, status, or measurement data, while the second channel supports another instrument function. The +5 V supply and 16-SOIC package are compatible with established instrument electronics, and the MAX232A family's higher slew rate can support improved RS-232 transition behavior. Care is required because both sides of an RS-232 link may have different ground potentials. Use a solid common reference within the equipment, isolate the cable if ground loops are possible, and verify the maximum supported data rate and cable length from the manufacturer documentation.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: MAX232AEWE+T — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | MAX232EWE+T | MAX232EIDWR | MAX232ECDWR | MAX232EEWE+T |
|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Driver and Receiver Configuration | 2/2 transceiver | 2/2 transceiver | 2/2 transceiver | 2/2 transceiver | 2/2 transceiver |
| Supply Voltage | +5 V | +5 V | +5 V | +5 V | +5 V |
| Interface Support | EIA/TIA-232E and V.28/V.24 | EIA/TIA-232E and V.28/V.24 | EIA/TIA-232E and V.28/V.24 | EIA/TIA-232E and V.28/V.24 | EIA/TIA-232E and V.28/V.24 |
| Slew-Rate Family | MAX232A higher-slew-rate implementation | Base MAX232 family | Base MAX232 family | Base MAX232 family | Base MAX232 family |
| Charge-Pump Capacitor Requirement | External capacitors required; values in manufacturer data sheet | External capacitors required; values in manufacturer data sheet | External capacitors required; values in manufacturer data sheet | External capacitors required; values in manufacturer data sheet | External capacitors required; values in manufacturer data sheet |
Ana Farklılayıcılar
- Higher-slew-rate MAX232A family implementation (karşılaştırma:MAX232EWE+T)
- Two complete RS-232 channels in one 16-SOIC package (karşılaştırma:MAX232EIDWR)
- Supports standard RS-232 communication standards (karşılaştırma:MAX232ECDWR)
Tasarım Notları
Place the MAX232AEWE+T charge-pump capacitors directly beside their associated pins and keep each capacitor's return path short and continuous. Follow the manufacturer data-sheet capacitor values and layout drawing rather than substituting generic high-capacitance parts. Keep the RS-232 driver outputs away from receiver inputs and sensitive logic because the cable-side transitions are much larger than the internal logic levels.
Route each RS-232 driver output as a short, direct path toward its connector and preserve a continuous ground reference beneath the interface area. Avoid sharing narrow ground-current paths between the transceiver and switching regulators. If the board connects to a remote system with a potentially different ground potential, evaluate isolation or a carefully engineered common-reference design to prevent excessive current through the RS-232 interface.
Do not treat the MAX232AEWE+T as a surge-protection device. Add connector-side protection when cables are exposed to electrostatic discharge or industrial transients, and select protection parts that do not distort normal RS-232 signals. Also verify the exact ordering suffix, temperature grade, logic thresholds, and capacitor configuration before substitution; identical package dimensions alone do not establish drop-in compatibility.
Decouple the +5 V supply locally with the capacitance and placement specified by Analog Devices. The charge-pump network can produce supply ripple, so the bypass path should be independent of connector return currents and noisy switching nodes. Confirm the power-supply capacity for the IC and surrounding interface circuitry under startup and full-load conditions, particularly when the board also supports +3.3 V logic through level translation.
Uyumluluk Bilgisi
No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals status is stated in the product listings. AEC-Q100 is not applicable because this is a general-purpose RS-232 interface IC rather than an automotive-qualified device.