IPT007N06NATMA1 - 60V 300A OptiMOS 5 N-FET | Infineon
MPN: IPT007N06NATMA1 ✓ فعالIPT007N06NATMA1 جائزہ
A MOSFET (Metal-Oxide-Semiconductor Field-Effect Transistor) is a voltage-controlled semiconductor switch used to route and modulate current in power-conversion circuits. Within the broader taxonomy, MOSFETs sit under discrete semiconductors -> transistors -> FETs -> power MOSFETs. The OptiMOS 5 family from Infineon represents the fifth-generation trench MOSFET platform optimized for low RDS(on), low gate charge, and high avalanche ruggedness, making these parts the workhorse of modern synchronous rectification, motor drive, and hot-swap designs.
Key differentiating features include the 0.75 mOhm maximum RDS(on), industry-leading figure-of-merit (FOM = RDS(on) x QG), and a thermally enhanced PG-HSOF-8-1 package with an exposed source pad that drops thermal resistance dramatically compared with standard SO-8 footprints. The 60 V drain-source rating comfortably covers 12 V and 24 V bus rails with substantial margin for transients. Low QG and QOSS enable high-frequency switching up to several hundred kHz with manageable driver losses.
Typical applications span high-current DC-DC converters, synchronous rectification in telecom and server silver-box supplies, hot-swap and OR-ing controllers, battery protection and BMS discharge paths, and high-power brushless DC motor drives. The TOLL footprint also makes it attractive for space-constrained eMobility and industrial robotics designs where board area and thermal density both matter.
When designing with this device, pay close attention to PCB layout: the source pad is the dominant thermal path, so a generous top-side copper pour connected to the exposed pad is mandatory. Driver placement should minimize the gate-loop inductance to prevent unwanted ringing and dv/dt-induced turn-on.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that go beyond a single datasheet summary, giving engineers the cross-reference context needed for second-source qualification.
کے لیے ڈراپ اِن متبادل IPT007N06NATMA1 — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں IPT007N06NATMA1 (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Technology, MSL Level, Operating Temperature Range, RoHS Status.
IPT007N06N
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
BSZ060NE2LSATMA1
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →BSC014N06NSATMA1
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →IPD090N03LGATMA1
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →BSS316NH6327XTSA1
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →IPT007N06NATMA1 زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Technology | OptiMOS 5 (N-channel trench MOSFET) |
| Drain-Source Voltage (VDS) | 60 V |
| Continuous Drain Current (ID, TC=25C) | 300 A |
| On-Resistance (RDS(on), VGS=10V max) | 0.75 mOhm |
| Power Dissipation (PD, TC=25C) | 375 W |
| آپریٹنگ درجہ حرارت رینج | -55 C to +175 C (TJ) |
| پیکیج | PG-HSOF-8-1 (TOLL) |
| ماؤنٹنگ ٹائپ | Surface Mount |
| Configuration | Single N-channel |
| MSL لیول | MSL 1 (per JEDEC J-STD-020) |
| RoHS اسٹیٹس | Compliant |
| Lead-Free | Yes |
| ہیلوجن فری | Yes |
| Standard Pack Quantity | 3000 (Tape & Reel) |
IPT007N06NATMA1 پن کنفیگریشن
| پن 1 | GATE — Gate drive input |
| پن 2 | SOURCE — Source connection (also ties to exposed pad) |
| پن 3 | DRAIN — Drain connection (tab) |
| پن 4 | NC — Not connected (per datasheet) |
| پن 5 | NC — Not connected (per datasheet) |
| پن 6 | NC — Not connected (per datasheet) |
| پن 7 | NC — Not connected (per datasheet) |
| پن 8 | NC — Not connected (per datasheet) |
| پن PAD | SOURCE — Exposed source pad - thermal and electrical connection |
محفوظ آپریٹنگ ایریا (DC, TC=25C)
عام استعمالات
IPT007N06NATMA1 کے لیے موزوں ہے 6 ایپلیکیشنs: 12V / 24V Synchronous Rectification, Hot-Swap and OR-ing Controllers, Battery Protection and BMS Discharge Path, High-Power BLDC Motor Drive, Telecom and Server Silver-Box PSU, Industrial Robotics and Factory Automation.
12V / 24V Synchronous Rectification
The IPT007N06NATMA1 is purpose-built for the synchronous rectifier (sync-FET) position in 12 V and 24 V buck converters where ultra-low conduction loss directly improves efficiency. Its 0.75 mOhm RDS(on) and 60 V VDS rating comfortably exceed the worst-case bus transients seen on a 24 V telecom or server rail. In a typical 500 kHz buck converter the part replaces a Schottky diode on the low-side, cutting rectifier losses by 60-70% and eliminating reverse-recovery charge. Designers should drive the gate with a 10 V driver capable of sinking the QG quickly to keep dead-time short.
تجویز کردہ
Hot-Swap and OR-ing Controllers
In hot-swap and OR-ing power-path applications, the IPT007N06NATMA1 acts as the main load-switching element that inrush-limits a live backplane. Its 300 A continuous ID handles full-power server and telecom shelves, while the 60 V VDS rating protects against load-dump transients. The low RDS(on) keeps steady-state voltage drop below 30 mV at 40 A, well within ATX and AdvancedTCA hold-up budgets. Designers typically pair this MOSFET with a hot-swap controller that manages the gate ramp and fault response.
تجویز کردہ
Battery Protection and BMS Discharge Path
For battery management systems in e-mobility, e-bikes, and energy storage, the IPT007N06NATMA1 serves as the low-loss discharge FET in the battery pack. The 60 V rating covers 16S lithium packs, and the 0.75 mOhm RDS(on) minimizes pack self-heating during high-current discharge cycles. Mounted on the TOLL footprint with a large copper pour, junction temperatures stay well below the 175 C limit even at continuous 200 A load. A gate-driver IC handles pre-charge and short-circuit protection sequencing.
تجویز کردہ
High-Power BLDC Motor Drive
Industrial and e-mobility BLDC motor drives use the IPT007N06NATMA1 in the inverter half-bridge switching position. Its 300 A continuous current rating supports high-torque robotics and small EV traction motors, while the low QG and QOSS enable 50-100 kHz PWM with manageable switching loss. The TOLL footprint keeps the inverter compact enough for in-motor mounting. Designers should co-layout gate-driver and TVS clamp components to keep the gate-loop inductance below 5 nH.
تجویز کردہ
Telecom and Server Silver-Box PSU
Inside a 48 V-input telecom or hyperscale server PSU, the IPT007N06NATMA1 is the ideal primary-side high-current switch on the 48 V bus, or a secondary-side sync-FET on the 12 V output. The 60 V rating covers 48 V nominal plus full transient margin, and 0.75 mOhm RDS(on) keeps conduction losses below 1% at full load. The TOLL footprint allows very high power density designs, with the part often placed directly under a heatsink clip on the top side of the PCB.
تجویز کردہ
Industrial Robotics and Factory Automation
Factory automation and industrial robot controllers deploy the IPT007N06NATMA1 in servo-amplifier power stages where hundreds of amps can flow during peak acceleration. The 300 A rating and TOLL footprint allow compact, high-current modules that drop directly into 24 V and 48 V industrial bus architectures. The part's robustness against inductive transients and avalanche events makes it well suited to the harsh switching environment of motor drives. Galvanic isolation of the gate-drive signal is mandatory in such designs.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا IPT007N06NATMA1 — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | IPT007N06N | BSZ060NE2LSATMA1 | BSC014N06NSATMA1 | IPD090N03LGATMA1 |
|---|---|---|---|---|---|
| Brand | Infineon | Infineon | Infineon | Infineon | Infineon |
| Package | PG-HSOF-8-1 (TOLL) | PG-HSOF-8-1 (TOLL) - same | PG-TSDSON-8 (TOLL-class) | PG-TDSON-8 | PG-TO252-3 (DPAK) |
| Drain-Source Voltage (VDS) | 60 V | 60 V | 60 V | 60 V | 30 V |
| Continuous Drain Current (ID, TC=25C) | 300 A | 300 A | ~50 A | ~50 A | ~90 A |
| On-Resistance (RDS(on) max, VGS=10V) | 0.75 mOhm | 0.75 mOhm | ~6 mOhm | ~1.4 mOhm | ~9 mOhm |
| Technology Family | OptiMOS 5 | OptiMOS 5 | OptiMOS 2 | OptiMOS 5 | OptiMOS |
| Power Dissipation (PD, TC=25C) | 375 W | 375 W | 89 W | 62 W | 115 W |
| RoHS Compliant | Yes | Yes | Yes | Yes | Yes |
اہم امتیازی خصوصیات
- Industry-leading RDS(on) in TOLL-class footprint (بمقابلہBSZ060NE2LSATMA1)
- 300 A continuous current in compact TOLL package (بمقابلہBSC014N06NSATMA1)
- 60 V rating covers 24 V industrial bus with margin (بمقابلہIPD090N03LGATMA1)
ڈیزائن نوٹس
The PG-HSOF-8-1 (TOLL) package dissipates 375 W at TC = 25 C, but realistic PCB thermal resistance typically limits steady-state dissipation to 2-5 W without a heatsink. Design 4-6 square inches of top-side copper connected to the exposed source pad, with a thermal via array (12-25 vias) stitching to inner planes. Estimated: with 1 oz copper and 25 vias on FR-4, RthJA is roughly 25-35 C/W, allowing about 4 W steady-state at TA = 70 C before derating.
Minimize the gate-drive loop by placing the gate driver within 5 mm of the gate pin, with the gate-return trace running parallel and adjacent to the gate-drive trace on a separate layer. Avoid running gate traces across or near drain-source copper to keep dv/dt-induced coupling below the Miller turn-on threshold. Use a 10 ohm gate resistor plus a 1 nF source-bypass network to dampen ringing on fast switching edges.
The exposed source pad must be soldered to the PCB for both thermal and electrical reasons; insufficient solder will cause RthJA to rise sharply and may violate the 0.75 mOhm RDS(on) spec due to contact resistance. Follow the Infineon recommended land pattern exactly, including the via-array pitch and pad dimensions. Stencil aperture reduction of 80-90% is recommended to prevent solder-ball formation under the thermal pad during reflow.
Do not exceed VGS of +/-20 V; the gate oxide is thin for low QG and overdrive can permanently damage the device. Do not switch at dv/dt exceeding 10 kV/ns without local gate protection - the Miller coupling on TOLL packages is significant due to the low internal gate resistance. Finally, derate ID by case temperature per the datasheet curve; the 300 A rating assumes TC = 25 C, not TA.
تعمیل کی معلومات
RoHS compliant per Infineon product declaration. Industrial grade - not AEC-Q101 qualified; for automotive review the Infineon automotive-grade OptiMOS ordering code.