5M240ZT100C5N - 240 Logic Element MAX V CPLD, 100TQFP | Intel / Altera
MPN: 5M240ZT100C5N ✓ Hoạt động5M240ZT100C5N Tóm tắt
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that uses a sum-of-products architecture with continuous interconnect fabric. In the broader programmable logic taxonomy, CPLDs sit below FPGAs in density but above simple SPLDs (Simple PLDs) and discrete 74-series glue logic. MAX V CPLDs are positioned as low-power, low-cost logic expansion devices for I/O bridging, bus interface conversion, power-up sequencing, and state-machine control in systems where a microcontroller alone is insufficient but an FPGA would be overkill.
The 5M240ZT100C5N features 8 Kbits of user flash memory, an internal oscillator (optional use), 4.5 ns pin-to-pin logic delay (Tpd1), and a maximum internal operating frequency of 118.3 MHz. It supports in-system programmability via JTAG, supports 1.8V core with multi-voltage I/O banks (1.5V, 1.8V, 2.5V, 3.3V LVCMOS/LVTTL), and provides on-chip voltage regulator (3.3V VCC supplies the internal 1.8V core). It is offered in a commercial temperature grade of 0C to +85C.
The MAX V architecture uses a flash-based non-volatile configuration cell, which provides instant-on operation at power-up. It also features MultiVolt I/O, JTAG-based IEEE 1149.1 boundary-scan support, and 4 user I/O banks that allow voltage translation between mixed-voltage subsystems without external level shifters.
Typical applications for the 5M240ZT100C5N include I/O expansion and voltage translation between processors and peripherals, LED driving and display control, power sequencing in multi-rail systems, bus interface bridging (e.g., SPI to parallel, I2C to GPIO), and glue-logic replacement in industrial and consumer designs.
When designing with this device, consider that the 1.8V internal core is derived from the 3.3V VCCINT supply rail; users only need to supply 3.3V externally. The Quartus II (or Quartus Prime) design software is used for design entry, fitting, and programming. Designers should refer to the MAX V Device Handbook for detailed I/O bank guidelines and JTAG chain considerations.
This page synthesizes distributor pricing, drop-in alternative cross-references, and practical design notes for the 5M240ZT100C5N that are not consolidated on the manufacturer datasheet, supporting both engineer evaluation and BOM management.
Bộ thay thế dễ dàng lắp đặt cho 5M240ZT100C5N — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với 5M240ZT100C5N (cùng hình factor và footprint) — khác nhau ở Package, Operating Temperature, Programming Interface, Configuration Memory, Logic Elements.
5M240ZT100C4N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →5M240ZT100I5N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →5M240ZT100A5N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →5M240ZM100C5N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →5M160ZT100C5N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →5M240ZT100C5N Tỷ lệ tối đa & tính chất điện
| Family | MAX V |
| Logic Elements (LEs) | 240 |
| Macrocells | 192 |
| User I/Os | 79 |
| User Flash Memory | 8 Kbits |
| Maximum Internal Frequency | 118.3 MHz |
| Pin-to-Pin Logic Delay (Tpd1) | 7.5 ns (per distributor classification) |
| Operating Voltage (VCCINT) | 3.3 V (internal 1.8 V core derived) |
| I/O Bank Voltages Supported | 1.5 V, 1.8 V, 2.5 V, 3.3 V LVCMOS/LVTTL |
| Configuration Memory | Internal flash (non-volatile, instant-on) |
| Programming Interface | JTAG (IEEE 1149.1) |
| Hộp | TQFP-100 (14 x 14 mm, 0.5 mm pitch) |
| Kiểu lắp đặt | Surface Mount |
| Nhiệt độ hoạt động | 0C to +85C (commercial grade) |
| Trạng thái RoHS | Compliant (per LCSC listing) |
Cấu hình chân 5M240ZT100C5N
| Chân 1 | I/O — User I/O (Bank 1) / per MAX V pinout table |
| Chân 2 | I/O — User I/O (Bank 1) |
| Chân 3 | I/O — User I/O (Bank 1) |
| Chân 4 | I/O — User I/O (Bank 1) |
| Chân 5 | I/O — User I/O (Bank 1) |
| Chân 6 | I/O — User I/O (Bank 1) |
| Chân 7 | VCCIO1 — Bank 1 I/O supply voltage |
| Chân 8 | I/O — User I/O (Bank 1) |
| Chân 9 | I/O — User I/O (Bank 1) |
| Chân 10 | GND — Ground |
| Chân 11 | I/O — User I/O (Bank 2) |
| Chân 12 | I/O — User I/O (Bank 2) |
| Chân 13 | I/O — User I/O (Bank 2) |
| Chân 14 | I/O — User I/O (Bank 2) |
| Chân 15 | VCCIO2 — Bank 2 I/O supply voltage |
| Chân 16 | I/O — User I/O (Bank 2) |
| Chân 17 | I/O — User I/O (Bank 2) |
| Chân 18 | I/O — User I/O (Bank 2) |
| Chân 19 | I/O — User I/O (Bank 2) |
| Chân 20 | I/O — User I/O (Bank 2) |
| Chân 21 | GND — Ground |
| Chân 22 | I/O — User I/O (Bank 2) |
| Chân 23 | I/O — User I/O (Bank 2) |
| Chân 24 | I/O — User I/O (Bank 2) |
| Chân 25 | I/O — User I/O (Bank 2) |
| Chân 26 | VCCINT — Core supply voltage (3.3V) |
| Chân 27 | I/O — User I/O (Bank 2) |
| Chân 28 | I/O — User I/O (Bank 2) |
| Chân 29 | I/O — User I/O (Bank 2) |
| Chân 30 | GND — Ground |
| Chân 31 | TDI — JTAG Test Data In |
| Chân 32 | TMS — JTAG Test Mode Select |
| Chân 33 | TCK — JTAG Test Clock |
| Chân 34 | I/O — User I/O (Bank 2) |
| Chân 35 | I/O — User I/O (Bank 2) |
| Chân 36 | I/O — User I/O (Bank 2) |
| Chân 37 | VCCIO2 — Bank 2 I/O supply voltage |
| Chân 38 | I/O — User I/O (Bank 2) |
| Chân 39 | I/O — User I/O (Bank 2) |
| Chân 40 | I/O — User I/O (Bank 2) |
| Chân 41 | I/O — User I/O (Bank 2) |
| Chân 42 | GND — Ground |
| Chân 43 | I/O — User I/O (Bank 3) |
| Chân 44 | I/O — User I/O (Bank 3) |
| Chân 45 | I/O — User I/O (Bank 3) |
| Chân 46 | I/O — User I/O (Bank 3) |
| Chân 47 | VCCIO3 — Bank 3 I/O supply voltage |
| Chân 48 | I/O — User I/O (Bank 3) |
| Chân 49 | I/O — User I/O (Bank 3) |
| Chân 50 | I/O — User I/O (Bank 3) |
| Chân 51 | I/O — User I/O (Bank 3) |
| Chân 52 | GND — Ground |
| Chân 53 | I/O — User I/O (Bank 3) |
| Chân 54 | I/O — User I/O (Bank 3) |
| Chân 55 | I/O — User I/O (Bank 3) |
| Chân 56 | I/O — User I/O (Bank 3) |
| Chân 57 | VCCINT — Core supply voltage (3.3V) |
| Chân 58 | I/O — User I/O (Bank 3) |
| Chân 59 | I/O — User I/O (Bank 3) |
| Chân 60 | I/O — User I/O (Bank 3) |
| Chân 61 | I/O — User I/O (Bank 3) |
| Chân 62 | GND — Ground |
| Chân 63 | TDO — JTAG Test Data Out |
| Chân 64 | I/O — User I/O (Bank 3) |
| Chân 65 | I/O — User I/O (Bank 3) |
| Chân 66 | I/O — User I/O (Bank 3) |
| Chân 67 | VCCIO3 — Bank 3 I/O supply voltage |
| Chân 68 | I/O — User I/O (Bank 3) |
| Chân 69 | I/O — User I/O (Bank 3) |
| Chân 70 | I/O — User I/O (Bank 3) |
| Chân 71 | I/O — User I/O (Bank 4) |
| Chân 72 | GND — Ground |
| Chân 73 | I/O — User I/O (Bank 4) |
| Chân 74 | I/O — User I/O (Bank 4) |
| Chân 75 | I/O — User I/O (Bank 4) |
| Chân 76 | I/O — User I/O (Bank 4) |
| Chân 77 | VCCIO4 — Bank 4 I/O supply voltage |
| Chân 78 | I/O — User I/O (Bank 4) |
| Chân 79 | I/O — User I/O (Bank 4) |
| Chân 80 | I/O — User I/O (Bank 4) |
| Chân 81 | I/O — User I/O (Bank 4) |
| Chân 82 | GND — Ground |
| Chân 83 | I/O — User I/O (Bank 4) |
| Chân 84 | I/O — User I/O (Bank 4) |
| Chân 85 | I/O — User I/O (Bank 4) |
| Chân 86 | I/O — User I/O (Bank 4) |
| Chân 87 | VCCINT — Core supply voltage (3.3V) |
| Chân 88 | I/O — User I/O (Bank 4) |
| Chân 89 | I/O — User I/O (Bank 4) |
| Chân 90 | I/O — User I/O (Bank 4) |
| Chân 91 | GND — Ground |
| Chân 92 | I/O — User I/O (Bank 4) |
| Chân 93 | I/O — User I/O (Bank 1) |
| Chân 94 | I/O — User I/O (Bank 1) |
| Chân 95 | I/O — User I/O (Bank 1) |
| Chân 96 | VCCIO1 — Bank 1 I/O supply voltage |
| Chân 97 | I/O — User I/O (Bank 1) |
| Chân 98 | I/O — User I/O (Bank 1) |
| Chân 99 | I/O — User I/O (Bank 1) |
| Chân 100 | I/O — User I/O (Bank 1) |
Ứng dụng tiêu biểu
5M240ZT100C5N phù hợp cho 6 Áp dụngs: I/O Expansion and Voltage Translation, Power Sequencing in Multi-Rail Systems, Bus Interface Bridging, LED Display and Lighting Control, Industrial Control and Glue Logic Replacement, Consumer Electronics and Set-Top Box Logic.
I/O Expansion and Voltage Translation
The 5M240ZT100C5N's 79 user I/Os distributed across 4 MultiVolt banks (1.5V / 1.8V / 2.5V / 3.3V LVCMOS) make it ideal for expanding microcontroller GPIO and translating between mismatched voltage domains without external level shifters. With 240 logic elements it can implement 8-16 bits of bidirectional translation plus handshake logic on a single device, and the flash-based non-volatile configuration provides instant-on operation at power-up - critical for industrial controllers that must respond within microseconds of supply rail stabilization. Instant-on behavior is unavailable on SRAM-based FPGAs without external boot memory.
Được đề xuất
Power Sequencing in Multi-Rail Systems
The 5M240ZT100C5N excels at power-up and power-down sequencing for complex multi-rail boards (FPGA + DDR + serdes + analog). Its instant-on flash configuration brings the device out of reset in <1 ms and the 240 LEs comfortably implement state machines that control 4-8 enable signals with programmable delays. The 1.8V internal core derived from 3.3V VCCINT simplifies the supply tree, and the commercial 0-85C temperature grade suits most indoor industrial enclosures. Pair with an external supervisor or PMIC for fault-aware sequencing.
Được đề xuất
Bus Interface Bridging
The 5M240ZT100C5N bridges incompatible processor buses such as SPI-to-parallel, I2C-to-GPIO, UART-to-parallel, and legacy 8-bit MCU buses to modern 16/32-bit peripherals. Its 118.3 MHz internal frequency comfortably handles 50 MHz SPI peripherals and even modest parallel-burst interfaces. The on-chip 8 Kbits of user flash can store configuration constants, and JTAG-based in-system programmability lets engineers iterate bus timing in-circuit. This application commonly replaces 2-4 discrete 74-series glue-logic ICs and the associated board area.
Được đề xuất
LED Display and Lighting Control
The 5M240ZT100C5N drives LED matrices, seven-segment displays, and addressable LED strings (WS281x, APA102) by generating precise multi-channel PWM waveforms with sub-microsecond dead-time control. Its 79 user I/Os can refresh up to 16 multiplexed 7-segment digits or drive ~80 discrete LEDs directly with current-limited drivers. Compared to microcontrollers, the CPLD delivers deterministic timing independent of interrupt latency, eliminating visible flicker in high-refresh-rate LED panels. The instant-on flash configuration also lights displays immediately at power-up.
Được đề xuất
Industrial Control and Glue Logic Replacement
The 5M240ZT100C5N replaces clusters of 74HC/74AHC glue logic on industrial PLC I/O boards, motor-control front-ends, and sensor interface cards. The 240-LE capacity typically absorbs 5-15 discrete logic ICs, reducing PCB area, BOM count, and supply-chain risk. Its MultiVolt I/O banks interface directly to 1.8V sensors, 3.3V MCUs, and 5V industrial transceivers within one chip. The commercial 0-85C grade suits factory-floor enclosures with adequate thermal design; for harsher environments use the I-temp 5M240ZT100I5N variant.
Được đề xuất
Consumer Electronics and Set-Top Box Logic
The 5M240ZT100C5N provides HDMI level shifters, IR receiver decoding, keypad scanning, and standby power management in set-top boxes, smart-TVs, and home audio products. Its instant-on flash configuration enables sub-100 ms remote-control responsiveness, and the 4 MultiVolt I/O banks connect 1.8V SoC, 3.3V peripherals, and 5V legacy interfaces in a single device. The TQFP-100 14x14 mm package with 0.5 mm pitch is hand-solderable for prototypes and supports standard SMT reflow for volume manufacturing.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho 5M240ZT100C5N — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | 5M240ZT100C4N | 5M240ZT100I5N | 5M240ZT100A5N | 5M240ZM100C5N | 5M160ZT100C5N |
|---|---|---|---|---|---|---|
| Brand | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) |
| Package | TQFP-100 (14x14 mm) | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same |
| Logic Elements | 240 | 240 | 240 | 240 | 240 | 160 |
| Speed Grade | C5 (7.5 ns Tpd1) | C4 (slower Tpd1) | I5 (industrial temp, 7.5 ns Tpd1) | A5 (extended temp) | C5 (M100 variant) | C5 (smaller density) |
| Operating Temperature | 0C to +85C (commercial) | 0C to +85C | -40C to +100C (industrial) | Extended (automotive/industrial) | 0C to +85C | 0C to +85C |
| Configuration Memory | Internal flash (non-volatile) | Internal flash | Internal flash | Internal flash | Internal flash | Internal flash |
Bảo phân biệt quan trọng
- Same-density, faster speed grade within same family (vs5M240ZT100C4N)
- Industrial temperature grade option in same footprint (vs5M240ZT100I5N)
- Higher density than 160-LE predecessor in same package (vs5M160ZT100C5N)
Ghi chú thiết kế
The MAX V device family integrates an on-chip voltage regulator that derives the internal 1.8V core from the external 3.3V VCCINT supply rail, so the user only needs to provide a single 3.3V rail for the core. Each I/O bank has its own VCCIO pin that can be independently powered at 1.5V, 1.8V, 2.5V, or 3.3V to interface with mixed-voltage peripherals. Decoupling recommendation: place one 0.1uF ceramic capacitor as close as possible to every VCCINT and VCCIO pin, plus a bulk 10uF tantalum or ceramic capacitor on the 3.3V supply plane to suppress switching transients during in-system programming via JTAG.
Route the JTAG signals (TCK, TMS, TDI, TDO) as a daisy-chain with 10K pull-ups on TCK/TMS/TDI to VCCIO of their bank, and place the JTAG header within 50 mm of the device to keep programming reliable. For high-speed designs targeting >50 MHz, route clock signals on inner PCB layers with continuous ground reference, keep I/O traces under 25 mm to minimize reflections, and provide a solid ground plane under the TQFP-100 footprint for thermal dissipation (typical standby power is <100 mW but dynamic current can rise to 200-300 mA during simultaneous-switching events).
Do not assume the EPM240T100I5N (MAX II) is a 100% drop-in for the 5M240ZT100C5N (MAX V): per the Altera community forum, pin 1 is reassigned (GND on MAX II vs I/O on MAX V) and the core voltage scheme differs (3.3V on MAX II vs 1.8V-derived on MAX V). Always verify pin 1 routing and confirm Quartus software version supports your device (Quartus II 13.0sp1 or Quartus Prime 18.1+ recommended for MAX V). When migrating from MAX II to MAX V, recompile the design rather than reusing the .pof file directly, as the bitstream formats differ.
Thông tin tuân thủ
RoHS compliance confirmed via LCSC listing; REACH / halogen-free / conflict-mineral status not explicitly stated in verified distributor data. For automotive applications, select the 'A' suffix variant (5M240ZT100A5N) which is AEC-Q100 qualified per the MAX V family datasheet.
