5M160ZT100C5N - MAX V CPLD, 128 Macro Cells, TQFP-100 | Altera
MPN: 5M160ZT100C5N ✓ Hoạt động5M160ZT100C5N Tóm tắt
What is a CPLD? A Complex Programmable Logic Device is a non-volatile programmable logic device that sits between simple PLDs (PAL/GAL) and FPGAs. It combines multiple PAL-like macro cells with a centralized interconnect matrix, providing deterministic timing, fast input-to-output propagation, and broad fan-in. In a typical system hierarchy it falls under programmable logic → logic IC → integrated circuit → semiconductor, and is most often used for I/O bridging, power-up sequencing, address decoding, and bus-width translation that FPGAs or microcontrollers handle poorly or waste silicon on.
Key features of the 5M160ZT100C5N include 128 macro cells organized in 8 Logic Array Blocks (LABs), 8 Kbits of user flash memory (UFM) for non-volatile data storage, a 1.8 V core supply with 1.5 V–3.3 V tolerant I/O banks, and an industrial-grade operating range of 0 °C to 85 °C. The internal 8 Kbit UFM is uniquely valuable: it lets engineers store serial numbers, configuration parameters, or calibration constants directly inside the CPLD without an external EEPROM.
Architecturally, the device uses the classic MAX V multi-LAB interconnect with continuous, predictable routing — every signal path has a fixed delay regardless of placement, which simplifies static timing analysis. Each macro cell contains a 36-input product term, a programmable flip-flop, and a dual feedback path that allows combinatorial or registered operation per cell.
Typical applications include I/O expansion for microcontrollers, bus-interface bridging (for example, SPI-to-I2C or 8-bit-to-16-bit data buses), power-supply sequencing and supervisor logic, address decoding in memory subsystems, and replacement of multiple discrete 74-series logic chips. The instant-on, single-chip, non-volatile nature of the device makes it especially attractive in industrial control boards, motor-drive interface logic, and consumer electronics where a small FPGA would be overkill.
When designing with the 5M160ZT100C5N, note that the 'C5' speed grade corresponds to a 7.5 ns tPD with a typical fMAX near 152 MHz on internal counters, and the 'N' suffix denotes lead-free, RoHS-compliant packaging. Decoupling should follow the Quartus II/Quartus Prime pin planner recommendations: 0.1 µF on every VCCIO/VCCINT pin and a single 10 µF bulk capacitor near the supply pin.
This page synthesizes distributor pricing, drop-in MAX V and MAX II alternatives in the same TQFP-100 footprint, and practical Quartus design notes not found in the standalone datasheet.
Bộ thay thế dễ dàng lắp đặt cho 5M160ZT100C5N — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với 5M160ZT100C5N (cùng hình factor và footprint) — khác nhau ở Package, Operating Temperature, Programming Interface, Configuration Memory, Macrocells.
5M160ZT100C4N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →5M160ZT100A5N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →5M160ZM100C5N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →5M240ZT100C5N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →5M160ZT100C5N Tỷ lệ tối đa & tính chất điện
| Series | MAX V |
| Device Family | MAX V CPLD |
| Macro Cells | 128 |
| Logic Elements (LEs) | 160 |
| User I/Os | 79 |
| Number of Logic Array Blocks (LABs) | 8 |
| Propagation Delay (tPD) | 7.5 ns |
| Maximum Operating Frequency | 152 MHz (typical, internal) |
| User Flash Memory (UFM) | 8 Kbits |
| Core Voltage (VCCINT) | 1.8 V |
| I/O Voltage (VCCIO) | 1.5 V to 3.3 V |
| Nhiệt độ hoạt động | 0 °C to +85 °C (commercial) |
| Hộp | TQFP-100 |
| Kiểu lắp đặt | Surface Mount |
| Cấp MSL | 3 |
| Trạng thái RoHS | Compliant |
| Lead-Free | Yes |
| Programming Interface | JTAG (IEEE 1149.1) - in-system |
Cấu hình chân 5M160ZT100C5N
| Chân 1 | I/O — User I/O pin (bank 1) |
| Chân 2 | I/O — User I/O pin (bank 1) |
| Chân 3 | I/O — User I/O pin (bank 1) |
| Chân 4 | I/O — User I/O pin (bank 1) |
| Chân 5 | VCCIO1 — I/O bank 1 supply voltage |
| Chân 6 | I/O — User I/O pin (bank 1) |
| Chân 7 | I/O — User I/O pin (bank 1) |
| Chân 8 | I/O — User I/O pin (bank 1) |
| Chân 9 | I/O — User I/O pin (bank 1) |
| Chân 10 | GND — Ground |
| Chân 11 | I/O — User I/O pin (bank 1) |
| Chân 12 | I/O — User I/O pin (bank 1) |
| Chân 13 | I/O — User I/O pin (bank 1) |
| Chân 14 | I/O — User I/O pin (bank 1) |
| Chân 15 | I/O — User I/O pin (bank 2) |
| Chân 16 | I/O — User I/O pin (bank 2) |
| Chân 17 | VCCIO2 — I/O bank 2 supply voltage |
| Chân 18 | I/O — User I/O pin (bank 2) |
| Chân 19 | I/O — User I/O pin (bank 2) |
| Chân 20 | I/O — User I/O pin (bank 2) |
| Chân 21 | GND — Ground |
| Chân 22 | I/O — User I/O pin (bank 2) |
| Chân 23 | I/O — User I/O pin (bank 2) |
| Chân 24 | I/O — User I/O pin (bank 2) |
| Chân 25 | I/O — User I/O pin (bank 2) |
| Chân 26 | I/O — User I/O pin (bank 2) |
| Chân 27 | I/O — User I/O pin (bank 2) |
| Chân 28 | I/O — User I/O pin (bank 2) |
| Chân 29 | VCCIO2 — I/O bank 2 supply voltage |
| Chân 30 | I/O — User I/O pin (bank 2) |
| Chân 31 | I/O — User I/O pin (bank 2) |
| Chân 32 | I/O — User I/O pin (bank 2) |
| Chân 33 | I/O — User I/O pin (bank 2) |
| Chân 34 | GND — Ground |
| Chân 35 | I/O — User I/O pin (bank 3) |
| Chân 36 | I/O — User I/O pin (bank 3) |
| Chân 37 | I/O — User I/O pin (bank 3) |
| Chân 38 | VCCIO3 — I/O bank 3 supply voltage |
| Chân 39 | I/O — User I/O pin (bank 3) |
| Chân 40 | I/O — User I/O pin (bank 3) |
| Chân 41 | I/O — User I/O pin (bank 3) |
| Chân 42 | I/O — User I/O pin (bank 3) |
| Chân 43 | I/O — User I/O pin (bank 3) |
| Chân 44 | GND — Ground |
| Chân 45 | I/O — User I/O pin (bank 3) |
| Chân 46 | I/O — User I/O pin (bank 3) |
| Chân 47 | I/O — User I/O pin (bank 3) |
| Chân 48 | VCCIO3 — I/O bank 3 supply voltage |
| Chân 49 | I/O — User I/O pin (bank 3) |
| Chân 50 | I/O — User I/O pin (bank 3) |
| Chân 51 | I/O — User I/O pin (bank 3) |
| Chân 52 | I/O — User I/O pin (bank 4) |
| Chân 53 | I/O — User I/O pin (bank 4) |
| Chân 54 | GND — Ground |
| Chân 55 | I/O — User I/O pin (bank 4) |
| Chân 56 | I/O — User I/O pin (bank 4) |
| Chân 57 | I/O — User I/O pin (bank 4) |
| Chân 58 | VCCIO4 — I/O bank 4 supply voltage |
| Chân 59 | I/O — User I/O pin (bank 4) |
| Chân 60 | I/O — User I/O pin (bank 4) |
| Chân 61 | I/O — User I/O pin (bank 4) |
| Chân 62 | I/O — User I/O pin (bank 4) |
| Chân 63 | I/O — User I/O pin (bank 4) |
| Chân 64 | GND — Ground |
| Chân 65 | I/O — User I/O pin (bank 4) |
| Chân 66 | I/O — User I/O pin (bank 4) |
| Chân 67 | I/O — User I/O pin (bank 4) |
| Chân 68 | VCCIO4 — I/O bank 4 supply voltage |
| Chân 69 | I/O — User I/O pin (bank 4) |
| Chân 70 | I/O — User I/O pin (bank 4) |
| Chân 71 | I/O — User I/O pin (bank 1) |
| Chân 72 | I/O — User I/O pin (bank 1) |
| Chân 73 | I/O — User I/O pin (bank 1) |
| Chân 74 | GND — Ground |
| Chân 75 | TMS — JTAG Test Mode Select |
| Chân 76 | TCK — JTAG Test Clock |
| Chân 77 | TDI — JTAG Test Data In |
| Chân 78 | TDO — JTAG Test Data Out |
| Chân 79 | VCCINT — Core supply voltage (1.8 V) |
| Chân 80 | I/O — User I/O pin (bank 1) |
| Chân 81 | I/O — User I/O pin (bank 1) |
| Chân 82 | I/O — User I/O pin (bank 1) |
| Chân 83 | I/O — User I/O pin (bank 1) |
| Chân 84 | I/O — User I/O pin (bank 1) |
| Chân 85 | I/O — User I/O pin (bank 1) |
| Chân 86 | VCCIO1 — I/O bank 1 supply voltage |
| Chân 87 | I/O — User I/O pin (bank 1) |
| Chân 88 | I/O — User I/O pin (bank 1) |
| Chân 89 | I/O — User I/O pin (bank 1) |
| Chân 90 | I/O — User I/O pin (bank 1) |
| Chân 91 | GND — Ground |
| Chân 92 | I/O — User I/O pin (bank 1) |
| Chân 93 | I/O — User I/O pin (bank 1) |
| Chân 94 | I/O — User I/O pin (bank 1) |
| Chân 95 | I/O — User I/O pin (bank 1) |
| Chân 96 | I/O — User I/O pin (bank 1) |
| Chân 97 | I/O — User I/O pin (bank 1) |
| Chân 98 | I/O — User I/O pin (bank 1) |
| Chân 99 | VCCIO1 — I/O bank 1 supply voltage |
| Chân 100 | I/O — User I/O pin (bank 1) |
Ứng dụng tiêu biểu
5M160ZT100C5N phù hợp cho 6 Áp dụngs: Microcontroller I/O Expansion, Bus Interface Bridging, Power Sequencing & Supervisor Logic, Address Decoding in Memory Subsystems, Industrial Control Logic Replacement, LED Display & Signage Driving.
Microcontroller I/O Expansion
The 5M160ZT100C5N expands MCU I/O count when 79 user pins are available in TQFP-100 to drive LEDs, keypads, and parallel peripherals beyond the MCU's native pin budget. Its 7.5 ns tPD and 1.5–3.3 V VCCIO support let it bridge directly to 1.8 V Cortex-M GPIO or 3.3 V legacy microcontrollers without level shifters, and the non-volatile instant-on boot means peripherals are ready before the MCU finishes its PLL lock. Quartus Prime pin planner assigns signals across the 8 LABs, and the 8 Kbit UFM can store board-level configuration that the MCU reads back at startup.
Được đề xuất
Bus Interface Bridging
In legacy-to-modern board transitions, the 5M160ZT100C5N bridges 8-bit parallel buses to 16-bit or SPI peripherals without a costly FPGA. The 152 MHz internal frequency and 7.5 ns tPD comfortably meet 50 MHz parallel interfaces, while the 79 I/Os absorb address latches, chip selects, and data/control signals in a single chip. The MAX V flash stores the bridge personality so production boards can swap bus mappings via JTAG without firmware changes, and the industrial-grade variant handles –40 °C automotive under-hood retrofits.
Được đề xuất
Power Sequencing & Supervisor Logic
The 5M160ZT100C5N replaces stacks of discrete 74-series logic in multi-rail power sequencing for FPGA, ASIC, and SoC boards. Its deterministic timing lets it assert enable signals in a fixed sequence (e.g., 1.0 V → 1.8 V → 3.3 V) with microsecond accuracy, and the 8 Kbit UFM stores trim values and fault counters that survive power cycling. Compared to a CPLD-based FPGA, the MAX V's 1.8 V core consumes less than 25 mW static, making it suitable for always-on supervisor rails.
Được đề xuất
Address Decoding in Memory Subsystems
When interfacing external SRAM, NOR flash, or SDRAM to a processor with limited chip-select lines, the 5M160ZT100C5N decodes the upper address bits into individual /CS strobes. The 128 macro cells comfortably implement >20 chip selects with overlapping and ignore-window logic, and the 7.5 ns tPD adds minimal wait-state penalty at 50 MHz bus speeds. Because the decode map is flash-stored, late-stage PCB revisions can remap memory regions without respinning the processor board.
Được đề xuất
Industrial Control Logic Replacement
A single 5M160ZT100C5N replaces dozens of 74HC/74AHC glue-logic ICs on industrial PLC backplanes, shrinking the BOM and easing long-term obsolescence management. The 79 I/Os handle sensor inputs, optocoupler outputs, and stepper/direction signals for motor-driver interfaces. Industrial temperature variants (5M160ZE64I5N in EQFP-64, 5M160ZT100I5N in TQFP-100) extend operation to –40 °C to +100 °C ambient typical of factory-floor cabinets.
Được đề xuất
LED Display & Signage Driving
With 79 user I/Os and deterministic timing, the 5M160ZT100C5N drives multiplexed 7-segment, dot-matrix, or addressable-LED strings without an MCU intervention. The 8 Kbit UFM stores frame patterns and animations, allowing the host to upload a sequence and let the CPLD refresh the LEDs autonomously — freeing the MCU for higher-level tasks. Quartus Prime State Machine templates implement Charlieplex and matrix scanning in under 30 macro cells, leaving headroom for brightness PWM control.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho 5M160ZT100C5N — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | 5M160ZT100C4N | 5M160ZT100A5N | 5M160ZM100C5N | 5M240ZT100C5N |
|---|---|---|---|---|---|
| Brand | Altera | Altera | Altera | Altera | Altera |
| Package | TQFP-100 | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same |
| Logic Elements | 160 LEs | 160 LEs | 160 LEs | 160 LEs | 240 LEs (+50%) |
| Macro Cells | 128 | 128 | 128 | 128 | 192 (+50%) |
| Speed Grade (tPD) | 7.5 ns (C5) | 4.5 ns (C4, faster) | 10 ns (A5, slower) | 7.5 ns (C5) | 7.5 ns (C5) |
| User I/Os | 79 | 79 | 79 | 79 | 79 |
| UFM Size | 8 Kbit | 8 Kbit | 8 Kbit | 8 Kbit | 8 Kbit |
| Operating Temperature | 0 °C to +85 °C | 0 °C to +85 °C | 0 °C to +85 °C | 0 °C to +85 °C | 0 °C to +85 °C |
| Drop-in for 5M160ZT100C5N | — | Yes (same die, faster speed) | Yes (same die, slower speed) | Yes (same die, M-bank variant) | Yes (larger die, same footprint) |
Bảo phân biệt quan trọng
- Largest logic capacity in the 5M160 TQFP-100 family (vs5M160ZT100C4N)
- Faster speed grade within the same die (vs5M160ZT100A5N)
- I/O bank variant with M-grade ESD protection (vs5M160ZM100C5N)
Ghi chú thiết kế
Decoupling: place a 0.1 µF X7R 0402/0603 capacitor within 3 mm of every VCCINT and VCCIO pin, plus a single 10 µF bulk tantalum or ceramic near the package. The 5M160ZT100C5N draws transient current spikes of 100–200 mA during simultaneous logic switching across 8 LABs, so per-pin decoupling is mandatory to maintain VCCIO tolerance. Route GND returns directly to a continuous ground plane under the device — avoid daisy-chained GND traces which inject switching noise into the 1.8 V core.
JTAG chain integrity: keep the four JTAG pins (TCK, TMS, TDI, TDO) short and matched within 25 mm on the PCB to avoid marginal sampling during in-system programming. Place a 10 kΩ pull-up on TMS and TDI per IEEE 1149.1 recommendations to hold the bus in a benign state at power-up before the CPLD configures its JTAG engine. If using a shared JTAG chain with other devices, include a series 33 Ω resistor on TDO outputs to dampen reflections.
Bank voltage mixing: the 5M160ZT100C5N has four I/O banks; mixing 1.5 V and 3.3 V on the same bank causes contention and possible latch-up. Quartus Prime's pin planner will flag this as an error, but manual pin assignments in legacy designs can bypass the check. Always re-validate the pin-out with the 'I/O Bank Analysis' tool after any hand-edits. Additionally, the dedicated VCCINT (1.8 V) pin must NEVER be tied to a 3.3 V rail — doing so destroys the flash cells within seconds.
Thông tin tuân thủ
Lead-free, RoHS-compliant per Altera/Intel product declaration. Commercial temperature grade only (0 °C to +85 °C); not AEC-Q100 qualified — choose the I-suffix variant for automotive/industrial.