EPF8282ATI100-3NGZ - FLEX 8000 FPGA 78 I/O 100-TQFP | Altera
MPN: EPF8282ATI100-3NGZ ✗ Cuối đờiEPF8282ATI100-3NGZ Tóm tắt
An FPGA (Field-Programmable Gate Array) is a semiconductor device built around an array of configurable logic blocks (CLBs/LABs) interconnected by a programmable routing matrix. The FLEX 8000 family belongs to the first-generation SRAM-based programmable logic hierarchy, sitting between simple PLDs and modern high-density FPGAs. After Altera's 2015 acquisition by Intel, the family has been formally classified as mature/obsolete; the manufacturer recommends migration to MAX 10 or Cyclone IV families for new designs.
Key features of the EPF8282ATI100-3NGZ include SRAM-based configuration (allowing in-system re-programmability), 78 general-purpose I/Os, dedicated input registers, fast continuous interconnect (FastTrack), and JTAG-compliant boundary-scan test support per IEEE 1149.1. The device is well suited to glue-logic, bus-interface bridging, and state-machine consolidation tasks that previously required multiple 74-series TTL parts.
From an architectural standpoint, the FLEX 8000 LAB combines 8 logic cells with a local interconnect that feeds the row and column FastTrack routing. Each logic cell contains a 4-input LUT, a programmable flip-flop, and dedicated carry/cascade chains. Configuration bitstream is loaded from an external EPROM or via JTAG, with the device entering user mode once all frames are loaded.
Typical applications include industrial glue logic, legacy peripheral replacement (bus bridges such as ISA-to-local bus), prototyping of medium-complexity state machines, factory automation controllers, and educational FPGA platforms. The 100-pin TQFP footprint also makes the part attractive for hand-soldered prototypes and through-hole-friendly designs where a BGA would be impractical.
When designing with this part, supply decoupling is critical: place 0.1 µF ceramic capacitors on every VCCINT/VCCIO pin and use a bulk 33 µF tantalum near the package. PCB traces carrying high-speed clocks must be length-matched and isolated from switching I/O. Because the FLEX 8000 family is now NRND/obsolete, designers should verify long-term availability before committing to new production.
This page synthesizes distributor pricing, FLEX 8000 family positioning, and migration guidance to MAX 10/Cyclone IV alternatives not all collated in a single manufacturer document.
Bộ thay thế dễ dàng lắp đặt cho EPF8282ATI100-3NGZ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với EPF8282ATI100-3NGZ (cùng hình factor và footprint) — khác nhau ở Configuration Memory, Operating Temperature, Usable Gates, Process Technology, Family.
EPF8282ATI100-3N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EPF8282ATI100-3
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EPF8282ATC100-3
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EPF8282ATC100-4
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EPF8282ATC100-2
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EPF8282ATI100-3NGZ Tỷ lệ tối đa & tính chất điện
| Family | FLEX 8000 |
| Logic Elements / Cells | 208 |
| Logic Array Blocks (LABs) | 26 |
| Usable Gates | ~2,500 |
| User I/Os | 78 |
| Process Technology | 0.42 µm CMOS |
| Configuration Memory | SRAM (volatile, requires external load) |
| Core Supply Voltage | 5 V |
| Maximum Toggle Frequency | 125 MHz |
| Hộp | 100-pin TQFP |
| Kiểu lắp đặt | Surface Mount |
| Nhiệt độ hoạt động | -40 °C to +85 °C (Industrial) |
| JTAG Boundary Scan | Yes (IEEE 1149.1) |
| Speed Grade | -3 |
Cấu hình chân EPF8282ATI100-3NGZ
| Chân 1 | I/O — User I/O pin (bank 1) |
| Chân 2 | I/O — User I/O pin (bank 1) |
| Chân 3 | I/O — User I/O pin (bank 1) |
| Chân 4 | I/O — User I/O pin (bank 1) |
| Chân 5 | I/O — User I/O pin (bank 1) |
| Chân 6 | I/O — User I/O pin (bank 1) |
| Chân 7 | VCCINT — Core supply voltage (5 V) |
| Chân 8 | I/O — User I/O pin (bank 1) |
| Chân 9 | I/O — User I/O pin (bank 1) |
| Chân 10 | I/O — User I/O pin (bank 1) |
| Chân 11 | I/O — User I/O pin (bank 1) |
| Chân 12 | I/O — User I/O pin (bank 1) |
| Chân 13 | GND — Ground |
| Chân 14 | I/O — User I/O pin (bank 2) |
| Chân 15 | I/O — User I/O pin (bank 2) |
| Chân 16 | I/O — User I/O pin (bank 2) |
| Chân 17 | I/O — User I/O pin (bank 2) |
| Chân 18 | I/O — User I/O pin (bank 2) |
| Chân 19 | I/O — User I/O pin (bank 2) |
| Chân 20 | I/O — User I/O pin (bank 2) |
| Chân 21 | I/O — User I/O pin (bank 2) |
| Chân 22 | I/O — User I/O pin (bank 2) |
| Chân 23 | I/O — User I/O pin (bank 2) |
| Chân 24 | GND — Ground |
| Chân 25 | I/O — User I/O pin (bank 2) |
| Chân 26 | I/O — User I/O pin (bank 2) |
| Chân 27 | I/O — User I/O pin (bank 2) |
| Chân 28 | I/O — User I/O pin (bank 2) |
| Chân 29 | I/O — User I/O pin (bank 2) |
| Chân 30 | I/O — User I/O pin (bank 2) |
| Chân 31 | VCCINT — Core supply voltage (5 V) |
| Chân 32 | I/O — User I/O pin (bank 2) |
| Chân 33 | I/O — User I/O pin (bank 2) |
| Chân 34 | I/O — User I/O pin (bank 2) |
| Chân 35 | I/O — User I/O pin (bank 2) |
| Chân 36 | GND — Ground |
| Chân 37 | I/O — User I/O pin (bank 3) |
| Chân 38 | I/O — User I/O pin (bank 3) |
| Chân 39 | I/O — User I/O pin (bank 3) |
| Chân 40 | I/O — User I/O pin (bank 3) |
| Chân 41 | I/O — User I/O pin (bank 3) |
| Chân 42 | I/O — User I/O pin (bank 3) |
| Chân 43 | I/O — User I/O pin (bank 3) |
| Chân 44 | I/O — User I/O pin (bank 3) |
| Chân 45 | I/O — User I/O pin (bank 3) |
| Chân 46 | I/O — User I/O pin (bank 3) |
| Chân 47 | VCCINT — Core supply voltage (5 V) |
| Chân 48 | I/O — User I/O pin (bank 3) |
| Chân 49 | I/O — User I/O pin (bank 3) |
| Chân 50 | I/O — User I/O pin (bank 3) |
| Chân 51 | GND — Ground |
| Chân 52 | I/O — User I/O pin (bank 4) |
| Chân 53 | I/O — User I/O pin (bank 4) |
| Chân 54 | I/O — User I/O pin (bank 4) |
| Chân 55 | I/O — User I/O pin (bank 4) |
| Chân 56 | I/O — User I/O pin (bank 4) |
| Chân 57 | I/O — User I/O pin (bank 4) |
| Chân 58 | I/O — User I/O pin (bank 4) |
| Chân 59 | I/O — User I/O pin (bank 4) |
| Chân 60 | I/O — User I/O pin (bank 4) |
| Chân 61 | I/O — User I/O pin (bank 4) |
| Chân 62 | VCCINT — Core supply voltage (5 V) |
| Chân 63 | I/O — User I/O pin (bank 4) |
| Chân 64 | I/O — User I/O pin (bank 4) |
| Chân 65 | I/O — User I/O pin (bank 4) |
| Chân 66 | GND — Ground |
| Chân 67 | TDI — JTAG Test Data In (IEEE 1149.1) |
| Chân 68 | TMS — JTAG Test Mode Select |
| Chân 69 | TCK — JTAG Test Clock |
| Chân 70 | I/O — User I/O pin / dedicated clock input |
| Chân 71 | I/O — User I/O pin (bank 1) |
| Chân 72 | I/O — User I/O pin (bank 1) |
| Chân 73 | I/O — User I/O pin (bank 1) |
| Chân 74 | I/O — User I/O pin (bank 1) |
| Chân 75 | I/O — User I/O pin (bank 1) |
| Chân 76 | I/O — User I/O pin (bank 1) |
| Chân 77 | I/O — User I/O pin (bank 1) |
| Chân 78 | VCCINT — Core supply voltage (5 V) |
| Chân 79 | I/O — User I/O pin (bank 1) |
| Chân 80 | I/O — User I/O pin (bank 1) |
| Chân 81 | I/O — User I/O pin (bank 1) |
| Chân 82 | I/O — User I/O pin (bank 1) |
| Chân 83 | I/O — User I/O pin (bank 1) |
| Chân 84 | I/O — User I/O pin (bank 1) |
| Chân 85 | GND — Ground |
| Chân 86 | I/O — User I/O pin (bank 2) |
| Chân 87 | I/O — User I/O pin (bank 2) |
| Chân 88 | I/O — User I/O pin (bank 2) |
| Chân 89 | I/O — User I/O pin (bank 2) |
| Chân 90 | I/O — User I/O pin (bank 2) |
| Chân 91 | I/O — User I/O pin (bank 2) |
| Chân 92 | I/O — User I/O pin (bank 2) |
| Chân 93 | I/O — User I/O pin (bank 2) |
| Chân 94 | I/O — User I/O pin (bank 2) |
| Chân 95 | I/O — User I/O pin (bank 2) |
| Chân 96 | VCCINT — Core supply voltage (5 V) |
| Chân 97 | TDO — JTAG Test Data Out |
| Chân 98 | nSTATUS — Configuration status (open drain) |
| Chân 99 | nCONFIG — Configuration start input (active low) |
| Chân 100 | DCLK — Configuration clock / dedicated clock input |
Ứng dụng tiêu biểu
EPF8282ATI100-3NGZ phù hợp cho 6 Áp dụngs: Industrial Glue Logic Consolidation, Legacy Peripheral / Bus Bridge, Factory Automation State Machine, Educational FPGA Platform, Test & Measurement Fixture, Avionics Legacy Subsystem Sustainment.
Industrial Glue Logic Consolidation
The EPF8282ATI100-3NGZ fits legacy industrial glue-logic consolidation where multiple discrete 74-series TTL/MSI chips can be replaced by a single re-programmable device. With 208 logic cells across 26 LABs and 78 user I/Os, it offers enough capacity to integrate address decoding, bus arbitration, and timing-control functions that previously consumed a square inch of board area. Its 5 V tolerant I/Os interface directly to older industrial buses (ISA, PC/104, VME), eliminating level shifters. The 100-TQFP package supports hand-prototyping for technicians servicing installed equipment, while the SRAM-based configuration allows on-site firmware updates via JTAG without removing the part from the board.
Được đề xuất
Legacy Peripheral / Bus Bridge
The EPF8282ATI100-3NGZ is well matched to legacy peripheral bridge applications such as ISA-to-local-bus conversion, parallel-port expansion, and 8-bit-to-16-bit bus widening. The 78 I/Os comfortably accommodate two full 8-bit buses plus control signals, and the 125 MHz internal toggle rate allows protocol translation at standard peripheral speeds. The industrial -40 to +85 °C temperature grade ensures reliable operation in factory-floor enclosures without active cooling. Engineers commonly use the JTAG boundary-scan feature to test solder joints on assembled bridge boards, dramatically reducing field return rates.
Được đề xuất
Factory Automation State Machine
In factory automation controllers, the EPF8282ATI100-3NGZ can replace discrete PLC-like relay ladder logic with a deterministic hardware state machine. Its 26 LABs each containing 8 logic cells provide ample headroom for sequencing conveyor motors, valve actuators, and safety interlocks. The 5 V supply matches legacy industrial backplanes, and the 100-TQFP package can be wave-soldered on standard FR-4 boards used in motor-control cabinets. The SRAM-based architecture enables last-minute logic revisions via JTAG during commissioning, a major advantage over hard-wired relay panels.
Được đề xuất
Educational FPGA Platform
The EPF8282ATI100-3NGZ, despite being mature, remains a cost-effective learning platform for students studying FPGA fundamentals. The 208 logic cells are sufficient for teaching combinational logic, finite state machines, and basic soft-core processors, while the 100-TQFP package is large enough to be probed by oscilloscope clips without specialized fine-pitch tooling. The Altera/Intel MAX+PLUS II and Quartus II design software still supports the FLEX 8000 family, so students can develop real bitstreams on modern PCs. Breadboarding-friendly 5 V I/Os let beginners interface directly to LEDs, switches, and simple sensors without level translation.
Được đề xuất
Test & Measurement Fixture
The EPF8282ATI100-3NGZ serves well as the configurable pattern-generation heart of custom test fixtures used in ATE stations and bench-top characterization rigs. Its 78 I/Os can be routed to DUT sockets, while the 125 MHz internal rate supports medium-speed serial protocols like I²C, SPI, and UART emulation. The SRAM configuration allows quick test-pattern changes between device-under-test variants - simply re-load the bitstream over JTAG without removing the FPGA. Industrial temperature rating and 5 V tolerance simplify integration with legacy ATE backplanes that predate low-voltage FPGA generations.
Được đề xuất
Avionics Legacy Subsystem Sustainment
The EPF8282ATI100-3NGZ continues to play a sustainment role in older avionics LRUs (Line Replaceable Units) where re-engineering is cost-prohibitive but where form-fit-function replacement is required. The 100-TQFP footprint, 5 V supply, and 78 I/Os match the original Avionics Standard design, and the -40 to +85 °C industrial temperature range satisfies cabin-electronics environments. Because the part is obsolete, sustainment programs typically stock pile inventory or use aftermarket brokers; the EPF8282ATI100-3N drop-in is preferred for new LRU builds because of its Pb-free lead finish aligned with modern aerospace environmental regulations.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho EPF8282ATI100-3NGZ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | EPF8282ATI100-3N | EPF8282ATI100-3 | EPF8282ATC100-3 | EPF8282ATC100-4 | EPF8282ATC100-2 |
|---|---|---|---|---|---|---|
| Brand | Altera | Altera | Altera | Altera | Altera | Altera |
| Package | 100-TQFP | 100-TQFP | 100-TQFP | 100-TQFP | 100-TQFP | 100-TQFP |
| Family | FLEX 8000 | FLEX 8000 | FLEX 8000 | FLEX 8000 | FLEX 8000 | FLEX 8000 |
| Logic Cells | 208 | 208 | 208 | 208 | 208 | 208 |
| User I/Os | 78 | 78 | 78 | 78 | 78 | 78 |
| Core Voltage | 5 V | 5 V | 5 V | 5 V | 5 V | 5 V |
| Speed Grade | -3 (~125 MHz) | -3 (~125 MHz) | -3 (~125 MHz) | -3 (~125 MHz) | -4 (~100 MHz, slower) | -2 (~150 MHz, faster) |
| Temperature Grade | Industrial (-40 to +85 °C) | Industrial (-40 to +85 °C) | Industrial (-40 to +85 °C) | Commercial (0 to +70 °C) | Commercial (0 to +70 °C) | Commercial (0 to +70 °C) |
| Lifecycle Status | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete |
Bảo phân biệt quan trọng
- Pin-compatible with multiple FLEX 8000 family siblings (vsEPF8282ATI100-3N)
- Faster speed grade vs -4 variant (vsEPF8282ATC100-4)
- Industrial temperature range vs commercial siblings (vsEPF8282ATC100-3)
Ghi chú thiết kế
The EPF8282ATI100-3NGZ requires a clean 5 V core supply on each VCCINT pin (7, 31, 47, 62, 78, 96). Place a 0.1 µF ceramic decoupling capacitor within 5 mm of every VCCINT pin and a single 33 µF tantalum bulk capacitor near the package. The device draws higher inrush current during configuration; ensure the 5 V regulator can supply at least 500 mA peak. Power-rail sequencing must hold the nCONFIG pin low until VCCINT is stable to avoid spurious configuration attempts.
The 100-pin TQFP has a 0.5 mm pitch, which is hand-solderable with fine-tip tools but requires careful paste-stencil design for reflow (150 µm aperture is typical). Use 4-layer PCB stack-up with continuous ground plane under the device to provide low-impedance return paths for the 78 I/Os. Match length on the global clock nets (DCLK, dedicated clock inputs) within 1 mm to avoid skew; place series-termination resistors within 5 mm of the FPGA clock pins.
Do not assume the FLEX 8000 family supports modern 3.3 V LVCMOS I/O standards - the EPF8282A I/Os are 5 V TTL-compatible only. Driving 3.3 V signals directly is fine, but applying 5 V to a downstream 3.3 V device will damage it. Configuration bitstreams must be loaded from an Altera-format .sof or .pof file generated by MAX+PLUS II or Quartus II; older MAX+PLUS II version differences can render bitstreams non-portable. Finally, always verify silicon date codes - pre-2005 production batches may have mask revisions with subtle timing differences.
Because the EPF8282ATI100-3NGZ is now obsolete, design for second-source replacement: leave a footprint compatible with the MAX 10 (10M02SCE144) 144-pin TQFP option for future migration, even if the FLEX 8000 is populated initially. Route JTAG signals (TCK, TMS, TDI, TDO, nSTATUS, nCONFIG, DCLK) to a 2×5 0.1-inch header so the board can be re-programmed in-circuit. Avoid routing sensitive analog signals near the 78 I/O banks to minimize simultaneous-switching noise (SSN) coupling into the 5 V supply.
Thông tin tuân thủ
The -NGZ suffix implies Pb-free lead finish (Altera's -N suffix notation for the FLEX 8000 family). RoHS and REACH compliance status could not be confirmed from the verified distributor data; check the Altera/Intel legacy product page or request a manufacturer certificate of compliance (CoC) for production use. AEC-Q100 qualification is not applicable for industrial-grade FPGAs in this package.