LM358DGKR - Dual 36V Operational Amplifier | Texas Instruments
MPN: LM358DGKR ✓ Hoạt độngLM358DGKR Tóm tắt
An operational amplifier, commonly called an op amp, is a high-gain differential amplifier whose open-loop behavior is shaped by external feedback networks. The LM358 belongs to the broader operational-amplifier hierarchy, within analog ICs and signal-chain conditioning. Its two independent channels allow one package to implement functions such as amplification, buffering, voltage comparison, difference amplification, and basic active filtering.
Key features include two amplifier circuits in one package, a supply capability reaching 36 V, input offset voltage of 300 µV typical, a common-mode input range that extends to ground, and high differential-input-voltage capability. These characteristics suit systems whose signal levels vary widely and whose analog section operates from a single positive supply. The device also provides a practical choice for cost-sensitive designs because two channels reduce component count and board area.
The LM358 architecture is intended for general-purpose rather than precision applications. Its typical 300 µV offset is useful for moderate-accuracy signal conditioning but requires careful bias-current compensation when the source impedance is high. Ground-referenced inputs are supported, which helps simplify single-supply interfaces. Designers should still evaluate output swing, input common-mode limits, supply headroom, capacitive-load stability, and channel-to-channel behavior at the selected voltage and temperature.
Typical uses include sensor-amplifier interfaces, transducer signal conditioning, low-side current measurement, audio preamplification, comparator stages, industrial control loops, and general buffering. In instrumentation designs, the two channels can process complementary or sequential signals. The 8-pin VSSOP outline supports compact layouts, although careful input routing and stable feedback connections remain important in noisy systems.
A key design consideration is to place input, feedback, and decoupling components close to their associated pins. Bypass the supply with a short, low-inductance connection, avoid long high-impedance input traces, and verify stability when driving capacitive loads. The common-mode input range and output swing must both be checked at the minimum and maximum operating supply.
This page combines manufacturer specifications, package guidance, commercially sourced alternatives, and practical design guidance for engineers evaluating the LM358DGKR as a dual, general-purpose, high-voltage operational amplifier.
Bộ thay thế dễ dàng lắp đặt cho LM358DGKR — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM358DGKR (cùng hình factor và footprint) — khác nhau ở Package, Maximum Supply Voltage, Common-Mode Input Range, Input Offset Voltage, Operating Temperature Range.
LM358ADGKR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM358DGKR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM358DGKR Tỷ lệ tối đa & tính chất điện
| Number of Amplifier Channels | 2 channels |
| Maximum Supply Voltage | 36 V |
| Input Offset Voltage | 300 µV typical |
| Common-Mode Input Range | Extends to ground |
| Differential Input Voltage Capability | High; exact limit not stated |
| Hộp | 8-pin VSSOP |
| Device Type | Standard general-purpose dual operational amplifier |
| Kiểu lắp đặt | Surface mount |
| Output Current | 30 mA; operating-condition qualification not stated |
Hướng dẫn cấu hình chân LM358DGKR 8-pin vssop
Cấu hình chân cho LM358DGKR (8-pin vssop gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho LM358DGKR.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
LM358DGKR phù hợp cho 6 Áp dụngs: Industrial Sensor Signal Conditioning, Low-Side Current Measurement, Audio Preamplification, Threshold Detection and Control, Communications Interface Buffering, Embedded Control Signal Conditioning.
Industrial Sensor Signal Conditioning
The LM358DGKR is well suited to conditioning low-level sensor signals because its common-mode input range extends to ground and its typical input offset voltage is 300 µV. Two amplifier channels can handle related inputs or implement a gain stage and an output buffer on the same board. With a 36 V maximum supply rating, the device can support higher-voltage industrial interfaces. Verify the input and output headroom at the actual supply voltage, compensate input bias current when the source resistance is high, and keep sensitive feedback nodes compact.
Được đề xuất
Low-Side Current Measurement
The LM358DGKR can amplify the small voltage produced across a low-side current-sense resistor while providing a common ground reference. Its dual-channel arrangement permits one channel to amplify the sense voltage and the other to buffer or support another stage in the measurement chain. The 300 µV typical offset becomes important when the measured voltage approaches that scale, so use suitable resistor values, account for input bias current, and confirm that output swing remains above the required measurement range.
Được đề xuất
Audio Preamplification
The LM358DGKR can serve as a general-purpose preamplifier for audio sources operating from a single positive supply. Its common-mode input range extending to ground supports coupling into the input stage, while the 36 V maximum rating provides flexibility for higher-voltage circuit arrangements. The device should be selected only after checking input bias current, output swing, gain-bandwidth behavior, and distortion expectations. A practical layout keeps the input path short and places the input bypass capacitor near the corresponding amplifier pin.
Được đề xuất
Threshold Detection and Control
The LM358DGKR can implement a comparator-style threshold detector with feedback or an open-loop decision stage when the required operating point is compatible with its input and output limits. The common-mode range extending to ground makes the device useful in grounded sensor systems, while the dual configuration allows two thresholds or a control signal plus a buffered reference. Check the minimum output levels, supply tolerances, and propagation behavior against the control-system timing requirements before using it as a precision comparator.
Được đề xuất
Communications Interface Buffering
The LM358DGKR can buffer or amplify intermediate communications signals where the design requires a grounded common-mode reference and a supply rating above typical low-voltage logic levels. Its two channels support independent receive-side or monitor functions on a compact board. For higher-speed communications nodes, verify bandwidth, slew rate, output swing, and capacitive-load stability because the LM358 is a general-purpose amplifier rather than a dedicated high-speed line driver. Use short traces and stable reference planes to minimize noise pickup.
Được đề xuất
Embedded Control Signal Conditioning
The LM358DGKR is appropriate for conditioning analog feedback signals in embedded-control and monitoring systems where two channels, ground-referenced inputs, and a 36 V maximum supply rating are useful. It can amplify a sensor feed and buffer an actuator-control signal, reducing the number of packages required. Design around the exact supply range, output-swing limits, input bias current, and channel behavior at the selected operating temperature. Decoupling and feedback stability are particularly important when the analog section shares a board with switching circuitry.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LM358DGKR — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LM358ADGKR | LM358DGKR |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | ROHM Semiconductor |
| Package | 8-pin VSSOP | 8-pin VSSOP | 8-pin TSSOP |
| Device Type | Standard general-purpose operational amplifier | LM358A-series general-purpose amplifier | Dual general-purpose operational amplifier |
| Series | LM358 | LM358A | LM358 |
| Mounting Style | Surface mount | Surface mount | Surface mount |
Bảo phân biệt quan trọng
- High-voltage general-purpose dual-amplifier option (vsLM358DGKR)
- Common-mode input operation extends to ground (vsLM358DGKR)
- Two general-purpose channels in one compact package (vsLM358ADGKR)
Ghi chú thiết kế
Place the supply bypass capacitor directly between the supply and ground pins, with the ground connection following the shortest practical path. Keep both feedback networks and high-impedance input traces away from switching nodes and inductor fields. Because two amplifiers share the package, route each channel according to its signal sensitivity rather than treating both channels as electrically or spatially identical.
The LM358 input-offset target of 300 µV typical makes source impedance and bias-current compensation important in high-gain stages. Use equal-value compensation resistors at the inputs when required by the manufacturer guidance, and avoid leakage from adjacent board surfaces. Also verify that the intended signal remains inside the common-mode range and that the calculated gain does not create a gain-bandwidth or stability problem.
Do not treat the 36 V maximum rating as a design target or assume the output can swing rail to rail. Check output current, output swing, common-mode limits, and operating-temperature limits at the selected supply. The 30 mA output-current figure also requires operating-condition qualification before it is used for load calculations.
Use separate local decoupling for each power pin when the package provides multiple supply connections. Keep the capacitor and amplifier on the same PCB side and minimize loop inductance, especially when the op amp follows a switching regulator. If the LM358 shares a rail with a converter, allow the converter to settle before enabling the sensitive analog section when the system architecture permits.
Thông tin tuân thủ
Compliance status is not stated in the manufacturer product information used for this record. Verify RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations for the exact orderable MPN.