LM393ADGKR - Dual 36V Comparator | Texas Instruments
MPN: LM393ADGKR ✓ Hoạt độngLM393ADGKR Tóm tắt
A differential comparator is an analog integrated circuit that evaluates the voltage difference between its inverting and non-inverting inputs. The LM393ADGKR belongs to the comparator and amplifier IC hierarchy within broader semiconductor and signal-conditioning applications. Its two channels operate independently, while a common supply and ground establish the operating reference for both comparators.
Key characteristics include a 2 mV input offset voltage, 250 nA input bias current, a 1.3 us response time, and an open-collector output configuration. The common-mode input range includes ground, supporting interfaces where one signal approaches the lower supply rail. Open-collector outputs can sink useful current and require an external pull-up resistor, enabling wired logic, level translation, and flexible output rise-time control.
The LM393ADGKR accepts single-supply operation across a broad voltage range, while dual-supply applications can use the available ±18 V operating range identified for this device. Because the output stage is open collector, the output voltage is set by the pull-up network rather than actively driven high. This architecture is efficient for alarm, relay-control, and interface circuits, but it also means the output cannot source current without suitable external circuitry.
Typical applications include industrial threshold detection, battery and power-supply monitoring, sensor conditioning, window comparison, and open-drain logic interfacing. The dual-channel configuration reduces component count when two independent comparisons are needed. It is also appropriate for systems that intentionally require a pull-up-defined high level, such as wired interconnects, indicator drivers, and level-shifting arrangements.
The principal design consideration is the open-collector output. Select a pull-up resistor that provides adequate sink current while keeping rise time within the system timing budget. Also verify input common-mode limits, supply sequencing, output leakage, and thermal conditions for the exact operating environment before finalizing the circuit.
This page consolidates electrical characteristics, verified lifecycle and compliance information, pin-compatible replacement options, and practical design guidance for engineers evaluating the LM393ADGKR in industrial, monitoring, and general-purpose comparator circuits.
Bộ thay thế dễ dàng lắp đặt cho LM393ADGKR — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM393ADGKR (cùng hình factor và footprint) — khác nhau ở Comparator Type, Number of Channels, Output Type, Package.
LM393BIDGKR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM293ADGKR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LM393DGKR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM393ADGKR Tỷ lệ tối đa & tính chất điện
| Comparator Type | Dual differential comparator |
| Number of Channels | 2 channels |
| Kiểu đầu ra | Open-collector |
| Supply Voltage Range | 2 V to 36 V |
| Dual Supply Voltage Range | ±1 V to ±18 V |
| Response Time | 1.3 us |
| Input Offset Voltage | 2 mV |
| Input Bias Current | 250 nA |
| Common-Mode Input Range | Includes ground |
| Input Type | Rail-to-Rail |
| Hộp | 8-pin VSSOP |
| Kiểu lắp đặt | Surface mount |
| Device Grade | Industrial grade |
| Trạng thái vòng đời | Active |
| RoHS Compliance | Compliant |
| REACH Compliance | Unknown |
| AEC-Q100 Qualification | Not qualified |
Hướng dẫn cấu hình chân LM393ADGKR 8-pin vssop
Cấu hình chân cho LM393ADGKR (8-pin vssop gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho LM393ADGKR.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
LM393ADGKR phù hợp cho 6 Áp dụngs: Industrial Threshold Detection, Power-Supply Monitoring, Battery Voltage Supervision, Sensor Signal Conditioning, Window Comparison, Open-Drain Interface Circuit.
Industrial Threshold Detection
The LM393ADGKR fits industrial threshold detection because its two independent channels compare input voltages with a 2 mV input offset and 1.3 us response time. Place one signal on each comparator input and use the open-collector output to drive an alarm, relay, or digital input. The common-mode range includes ground, which is useful when monitoring low-level process or sensor signals. A pull-up resistor establishes the inactive logic level and should be selected from the required sink current and maximum transition-time constraints.
Được đề xuất
Power-Supply Monitoring
The LM393ADGKR can monitor a power rail by comparing its voltage against a reference-derived threshold. Its 2 V to 36 V single-supply capability covers a broad range of industrial and embedded supply levels, while the open-collector output can directly alert a system controller. The two channels permit monitoring of a supply and its associated signal simultaneously. Account for input offset tolerance, reference accuracy, and the pull-up voltage when setting the system trip point.
Được đề xuất
Battery Voltage Supervision
The LM393ADGKR is appropriate for battery supervision when an early warning or undervoltage event must trigger a discrete control action. Its low 250 nA input bias current helps reduce measurement disturbance, and the 1.3 us response time allows rapid transition during threshold crossing. The open-collector output can pull a supervisor line low or drive an indicator through a pull-up. Select the external reference and resistor divider carefully so battery chemistry, tolerance, and temperature do not create false trips.
Được đề xuất
Sensor Signal Conditioning
The LM393ADGKR converts an analog sensor level into a logic decision when used as a threshold comparator. The differential inputs allow a sensor signal to be compared with a reference, and the 2 mV offset is useful when the decision boundary is close to the measured level. The common-mode range includes ground, supporting sensors whose output approaches the lower rail. For slow sensor signals, account for noise around the threshold and add filtering before the comparator when excessive output toggling is observed.
Được đề xuất
Window Comparison
The LM393ADGKR supports window comparison by assigning its two independent channels to the lower and upper limits of an acceptable signal range. The two 1.3 us channels allow both boundaries to be evaluated, while their open-collector outputs can be combined through suitable pull-ups and logic. This arrangement is useful for validating supply levels, signal ranges, or sensor limits. Review output-state conventions carefully when combining the channels, and confirm that the common-mode range covers both threshold voltages.
Được đề xuất
Open-Drain Interface Circuit
The LM393ADGKR's open-collector outputs make it useful for wired open-drain interfaces, status buses, and level translation. Each output can pull a logic node toward ground while an external pull-up connects that node to the desired supply voltage. With a 1.3 us response time, the device suits general-purpose control and alarm signals rather than very high-speed data channels. Select the pull-up voltage for the receiving device, check output leakage during the high state, and include the receiver input current in the resistor calculation.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LM393ADGKR — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LM393BIDGKR | LM293ADGKR | LM393DGKR |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | VSSOP-8 (DGK) | VSSOP-8 (DGK) | VSSOP-8 (DGK) | VSSOP-8 (DGK) |
| Comparator Channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Output Type | Open-collector | Open-collector | Open-collector | Open-collector |
| Automotive Qualification | Not qualified | Not qualified | Not qualified | Not qualified |
Bảo phân biệt quan trọng
- Lower offset and bias currents in the B-version upgrade (vsLM393BIDGKR)
- Faster family-member response time (vsLM393BIDGKR)
- Higher maximum operating-voltage rating (vsLM393BIDGKR)
Ghi chú thiết kế
Do not treat the open-collector output as a push-pull logic output. Every output node needs an external pull-up resistor unless another open-drain device or pull-up network already provides one. Select the resistor so that the low-state sink current remains within the device rating while the high-state rise time meets the circuit timing requirement. Include every receiver input current and output leakage path in the high-level calculation.
Keep the common-mode input voltages inside the specified operating range, which includes ground but does not imply unlimited rail-to-rail input capability. This matters near the upper supply rail and when the comparator is used with ±18 V dual supplies. The 2 mV input offset also contributes directly to the switching threshold, so resistor and reference tolerances should be included when defining a precision trip point.
Route the two comparator channels with attention to nearby switching nodes because differential input traces can pick up coupled noise. Keep the input and pull-up connections short, place the pull-up resistor close to the output node, and maintain separation from high-current or high-voltage switching paths. For sensitive threshold measurements, ground the input-referenced circuitry carefully and evaluate filtering without adding excessive delay to the 1.3 us response target.
The comparator is normally used in a low-power signal-conditioning role, but actual dissipation and junction temperature depend on the exact device limits, supply voltage, output duty cycle, and ambient environment. Verify these conditions against the manufacturer operating and absolute-maximum ratings. Because the VSSOP package has limited heat-spreading area, avoid placing the device next to a high-dissipation regulator without reviewing the PCB thermal path.
Thông tin tuân thủ
RoHS compliance is identified in the component listing. REACH, lead-free status, halogen-free status, and conflict-minerals status are not confirmed by the manufacturer documentation used for this page. The LM393A is identified as an industrial-grade device.