THS4223PWP - Dual 230MHz R-R Output Amplifier | TI
MPN: THS4223PWP ✗ Cuối đờiTHS4223PWP Tóm tắt
A high-speed voltage-feedback operational amplifier is a linear IC that increases the amplitude of an input signal while using negative feedback to establish gain and bandwidth. This device belongs to the operational amplifier hierarchy, which includes voltage-feedback and current-feedback amplifiers used for signal conditioning, analog conversion, buffering, and drive applications. Its low supply-voltage range supports portable, industrial, communications, and test-equipment systems where circuit area and power consumption are tightly constrained.
The THS4223PWP provides two amplifier channels, rail-to-rail output swing, and a bandwidth of 230 MHz. Its high output-current capability enables it to drive heavier loads than a conventional small-signal high-speed amplifier. The operating temperature range is -40 °C to +85 °C, supporting industrial-temperature equipment. The PowerPAD-backed TSSOP package also offers a practical thermal path when the exposed pad is connected to the PCB ground plane.
The rail-to-rail output architecture is especially useful when driving analog-to-digital converter inputs, video preamplifier stages, or other downstream circuits whose signal range approaches the available supply voltage. Because the amplifier operates down to 1.35 V, it can support compact systems in which conventional high-speed amplifiers would require a larger supply. The 900 mA output-current figure must still be evaluated against thermal limits, load impedance, supply voltage, and the output waveform before it is treated as a continuous operating point.
Typical applications include low-voltage ADC signal conditioning, video preamplification, communications-interface amplification, test and measurement front ends, and general-purpose high-speed buffering. In these systems, the 230 MHz bandwidth provides signal-path bandwidth while the dual configuration can reduce the number of active components needed for balanced or two-channel circuitry. The exposed thermal pad and short high-speed feedback paths remain important for preserving stability and usable bandwidth.
PCB implementation should follow the manufacturer datasheet layout and component recommendations, particularly for decoupling capacitors, exposed-pad grounding, and feedback routing. Keep high-speed feedback traces short, provide a low-impedance return path beneath the device, and avoid placing sensitive analog inputs beside digital switching nodes. Check the output-current and thermal limits for the intended load rather than relying only on the headline current capability.
This product record combines the confirmed THS4223PWP electrical, package, and sourcing information with engineering-oriented application guidance, pin-architecture cautions, and drop-in replacement analysis. It is intended to support faster component selection for designs requiring high-speed, low-voltage, rail-to-rail-output amplification.
Bộ thay thế dễ dàng lắp đặt cho THS4223PWP — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
THS4223IPWP
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
THS4223PWP Tỷ lệ tối đa & tính chất điện
| Number of Amplifier Channels | 2 circuits |
| Amplifier Type | Voltage Feedback |
| Supply Voltage Range | 1.35 V to 7.5 V |
| Gain-Bandwidth Product | 230 MHz |
| Output Current Capability | 900 mA |
| Output Swing | Rail-to-Rail |
| Khoảng nhiệt độ hoạt động | -40 °C to +85 °C |
| Package Type | TSSOP-14 with exposed PowerPAD |
| Số lượng chân | 14 pins |
| Terminal Count | 14 terminals |
| Kiểu lắp đặt | Surface Mount |
| Temperature Grade | Industrial |
Hướng dẫn cấu hình chân THS4223PWP tssop-14 with exposed powerpad
Cấu hình chân cho THS4223PWP (tssop-14 with exposed powerpad gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho THS4223PWP.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
THS4223PWP phù hợp cho 6 Áp dụngs: Low-Voltage ADC Signal Conditioning, Video Preamplification, Communications Signal Conditioning, Test and Measurement Front End, Portable Analog Signal Conditioning, Industrial Sensor Interface.
Low-Voltage ADC Signal Conditioning
The THS4223PWP fits low-voltage ADC front ends because its 1.35 V to 7.5 V supply range supports compact analog systems and its 230 MHz gain-bandwidth product provides ample bandwidth for fast conversion signals. The dual configuration can condition two channels while preserving matching and reducing board area. Its rail-to-rail output is useful when the amplifier must approach the available signal range. Before selecting the gain, verify ADC input capacitance, settling requirements, noise, and the maximum input common-mode voltage against the manufacturer electrical tables.
Được đề xuất
Video Preamplification
The THS4223PWP is suitable for video preamplification because its 230 MHz bandwidth supports high-speed video signals and its rail-to-rail output can maximize swing within a compact low-voltage design. The 900 mA output-current capability can also drive heavier downstream loads than a conventional small-signal amplifier. In a video path, use short traces, maintain a continuous ground reference, and place decoupling close to the supply pins. Cable loading, gain distribution, output impedance, and the required video bandwidth should be evaluated before finalizing the stage.
Được đề xuất
Communications Signal Conditioning
The THS4223PWP can condition low-level communications signals when a system requires high bandwidth, rail-to-rail output swing, and more output drive than a conventional precision amplifier provides. Its 1.35 V minimum supply supports compact radio, interface, and data-conversion circuits, while the dual configuration allows two related channels in one package. Power-supply rejection, input common-mode range, and distortion should be checked at the operating gain and frequency. Keep the feedback network and input traces short to avoid parasitic feedback and bandwidth loss.
Được đề xuất
Test and Measurement Front End
The 230 MHz bandwidth of the THS4223PWP makes it useful in high-speed test and measurement front ends, buffer stages, and instrumentation signal paths. Rail-to-rail output improves utilization of low-voltage test ranges, while the two channels can be used for differential or dual-channel conditioning. The exposed PowerPAD must be connected to a suitable ground plane to improve heat transfer. Engineers should account for probe capacitance, fixture loading, source impedance, and gain-bandwidth interaction, particularly when configuring a low-noise amplifier for DC or low-frequency measurements.
Được đề xuất
Portable Analog Signal Conditioning
The THS4223PWP suits portable analog signal-conditioning systems because its supply voltage can extend down to 1.35 V, reducing the power burden associated with higher-voltage analog rails. The 230 MHz bandwidth supports fast sensor, data-conversion, and buffer paths, while rail-to-rail output increases usable signal excursion in compact hardware. Designers must verify supply rejection, output settling, and thermal performance at the intended frequency. Low-noise layout, local bypass capacitors, and a solid exposed-pad ground connection are especially important in small enclosures with limited heat spreading.
Được đề xuất
Industrial Sensor Interface
The dual THS4223PWP can amplify and buffer two sensor-related channels in an industrial interface when the system operates from a low-voltage rail and requires high bandwidth. Rail-to-rail output supports downstream circuitry with limited headroom, while the dual configuration helps reduce component count. Confirm the input common-mode range before connecting sensors because rail-to-rail output does not imply rail-to-rail input operation. Sensor excitation, grounding, shielding, settling time, and protection requirements should be evaluated independently of the amplifier's headline bandwidth and output-current capability.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho THS4223PWP — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | THS4223IPWP |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | HTSSOP-14 with exposed PowerPAD | HTSSOP-14 with exposed PowerPAD |
| Number of Channels | 2 | 2 |
| Gain-Bandwidth Product | 230 MHz | 230 MHz |
| Output Architecture | Rail-to-Rail | Rail-to-Rail |
Bảo phân biệt quan trọng
- Very low minimum supply voltage for a high-speed dual amplifier (vsTHS4223IPWP)
- Substantial output drive combined with high bandwidth (vsTHS4223IPWP)
- Rail-to-rail output improves low-voltage signal utilization (vsTHS4223IPWP)
Ghi chú thiết kế
The exposed PowerPAD is the primary thermal path for the THS4223PWP. Follow the manufacturer exposed-pad layout and connect the pad to the PCB ground plane with adequate vias. Output-current capability is not the same as continuous permissible dissipation; verify the load waveform, ambient temperature, package thermal data, and copper area before operating near the 900 mA device capability.
Place the required supply-bypass capacitors directly beside the power and ground terminals, and keep the high-speed feedback components and traces as short as practical. The PWP footprint includes an exposed pad in addition to the 14 gull-wing terminals. Use the manufacturer land pattern rather than constructing a generic TSSOP-14 footprint, because pad dimensions and thermal-via requirements can differ.
Avoid routing the input, feedback, and output paths near switching-node return currents. A continuous ground plane under the amplifier and short feedback loops help prevent parasitic feedback and loss of the intended 230 MHz bandwidth. For ADC and video interfaces, terminate cables and controlled-impedance traces according to the actual channel specification, and verify settling with realistic load capacitance.
Thông tin tuân thủ
No definitive RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status was confirmed for this exact MPN.