AD5303ARU - Dual 8-Bit Rail-to-Rail DAC | Analog Devices
MPN: AD5303ARU ✓ 啟用中AD5303ARU 概覽
A DAC is a data-conversion integrated circuit that translates a digital code into a proportional analog voltage or current. The AD5303 belongs to the voltage-output DAC family, where buffered outputs are driven directly by on-chip amplifiers. Its rail-to-rail output stage allows the analog outputs to approach the available supply rails, while the dual-channel architecture supports two independent analog control or excitation channels in a compact footprint.
The principal features include 8-bit resolution on each channel, a versatile 3-wire serial interface compatible with SPI, QSPI, MICROWIRE, and DSP interface standards, and serial clock operation up to 30 MHz. Each converter derives its reference from a dedicated reference pin, allowing the two output voltages to be scaled independently. The single-supply operating range supports both 3.3 V and 5 V systems.
Internally, the device uses a resistor-string DAC architecture followed by buffered output amplifiers. This arrangement provides direct voltage output without requiring an external output buffer and simplifies connection to analog front ends. The 16-lead TSSOP package is suitable for compact analog and mixed-signal designs, while the dual channel count improves utilization when a system needs two matched control signals.
Typical applications include industrial process control, programmable test and measurement equipment, battery-powered instrumentation, sensor excitation, automated test equipment, and general-purpose analog signal generation. Its 230 uA current consumption at 3 V is especially useful in portable and distributed sensing systems where each subsystem must limit standby power.
Designers should treat the reference pins as precision analog nodes, route them away from digital switching currents, and use the pin-description table in the manufacturer datasheet when assigning PCB tracks. Confirm output settling time, reference voltage limits, and logic-level compatibility against the intended clock rate and analog settling requirements.
This page combines manufacturer specifications, drop-in device alternatives, application guidance, and design notes for engineers evaluating the AD5303ARU across low-power analog and mixed-signal systems.
直接替換替代品,適用於 AD5303ARU — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
AD5303ARUZ
✅ 直接替換📋 參考替代品(不在目錄中)
AD5303BRU
✅ 直接替換📋 參考替代品(不在目錄中)
AD5313ARUZ
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
AD5313BRU
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
AD5323ARUZ
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
AD5323BRU
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
AD5303ARU 最大額定值與電氣特性
| Number of DAC Channels | 2 |
| 解析度 | 8 bits per channel |
| DAC Architecture | Resistor string with buffered voltage output |
| Supply Voltage Range | 2.5 V to 5.5 V |
| Current Consumption | 230 uA at 3 V |
| 輸出類型 | Buffered voltage output |
| Output Swing | Rail-to-rail |
| Serial Interface | 3-wire serial interface |
| Interface Compatibility | SPI, QSPI, MICROWIRE, and DSP interfaces |
| Maximum Serial Clock Rate | 30 MHz |
| Reference Inputs | 2 independent reference pins |
| 封裝 | 16-lead TSSOP |
| 安裝類型 | Surface mount |
AD5303ARU 16-lead tssop 腳位配置指南
AD5303ARU(16-lead tssop 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: AD5303ARU.
請參閱 資料表 以查看完整腳位配置。
典型應用
AD5303ARU 適用於 6 應用s: Industrial Process Control, Programmable Test and Measurement, Portable Sensor Excitation, Battery-Powered Data Acquisition, Automated Test Equipment, Audio and Communication Control.
Industrial Process Control
The AD5303ARU fits closed-loop industrial controllers that need two adjustable analog command outputs from a compact controller board. Its two independent 8-bit channels can represent actuator commands, setpoints, or offset adjustments, while the 2.5 V to 5.5 V supply range supports both 24 V industrial designs with local regulation and compact 5 V control electronics. The 30 MHz serial-interface capability provides ample bandwidth for periodic updates from an industrial microcontroller or PLC interface module. Because the outputs use buffered rail-to-rail stages, external unity-gain amplifiers are unnecessary for normal high-impedance loads. Confirm loop settling requirements and analog input ranges before using the 8-bit step size for precision positioning.
推薦
Programmable Test and Measurement
The AD5303ARU can generate two independent stimulus levels for automated test equipment, bench instruments, and board-level test fixtures. Its 3-wire serial interface supports SPI, QSPI, MICROWIRE, and DSP standards, while operation up to 30 MHz permits rapid code updates during automated sequences. A dual converter avoids duplicating the digital interface and reference distribution when a fixture requires two bias or excitation voltages. The buffered rail-to-rail outputs can drive high-impedance measurement inputs directly, although cable loading, settling time, and reference accuracy must be evaluated for each channel. The 230 uA consumption at 3 V also supports compact low-power test modules.
推薦
Portable Sensor Excitation
The AD5303ARU is useful in portable or distributed sensor modules that must provide adjustable excitation or offset voltages beside a sensing frontend. Its 230 uA current consumption at a 3 V supply leaves more of the system power budget for sensing, signal conditioning, and short-range communications. Two independently referenced outputs can drive separate resistive bridges or compensate two measurement channels without duplicating the converter package. Rail-to-rail buffered operation provides useful output range in low-voltage designs, but the selected reference and load must remain within their documented limits. Validate the 8-bit resolution against the required excitation step, and account for reference drift when long-duration measurements depend on accurate excitation.
推薦
Battery-Powered Data Acquisition
The AD5303ARU supports low-power data-acquisition systems that need controllable analog outputs alongside sensors and amplifiers. Its single-supply operation from 2.5 V to 5.5 V allows direct use of a regulated 3.3 V or 5 V rail, and the 230 uA consumption at 3 V limits the converter's contribution to standby demand. Two buffered channels can generate offset, span, or excitation voltages for instrumentation amplifiers and analog-to-digital converters. Because the DAC includes on-chip output amplifiers, the signal path remains compact, but external protection may be needed when outputs drive long cables or potentially mistuned loads. Confirm output stability, reference settling, and sleep-state behavior in the complete analog subsystem.
推薦
Automated Test Equipment
The AD5303ARU is appropriate for automated test equipment that commands two analog levels through a common digital bus. Its SPI-compatible 3-wire interface and clock rate up to 30 MHz allow the converter to be updated rapidly between test steps without requiring separate data buses for each channel. Rail-to-rail buffered outputs support common low-voltage fixture biases and signal conditioning inputs, while the dual-reference arrangement allows independent scaling of the two commands. The 16-lead TSSOP package conserves board area in densely populated test-interface cards. When accuracy is critical, characterize the reference at temperature, verify full-scale settling after a code change, and keep high-current switching nodes away from the reference and analog output traces.
推薦
Audio and Communication Control
The AD5303ARU can provide two low-level control or bias voltages in audio and communication equipment where a dedicated audio codec is unnecessary. The buffered rail-to-rail outputs may set mixer-control levels, line-driver references, or small signal offsets, and the fast 3-wire interface allows a host controller to update both channels during configuration. Its 230 uA consumption at 3 V suits compact peripheral modules, although noise-sensitive analog paths require careful grounding and reference filtering. Because this is an 8-bit converter, use it for coarse control levels rather than fine amplitude synthesis, and evaluate glitch energy when updating codes between sensitive operating states. Keep return currents out of the reference ground path to avoid modulation of the two outputs.
推薦
推薦產品摘要
工程參考資料,適用於 AD5303ARU — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | AD5303ARUZ | AD5303BRU | AD5313ARUZ | AD5313BRU | AD5323ARUZ | AD5323BRU |
|---|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 16-lead TSSOP | 16-lead TSSOP - same | 16-lead TSSOP - same | 16-lead TSSOP - same | 16-lead TSSOP - same | 16-lead TSSOP - same | 16-lead TSSOP - same |
| Resolution | 8 bits | 8 bits | 8 bits | 10 bits | 10 bits | 12 bits | 12 bits |
| Number of DAC Channels | 2 | 2 | 2 | 2 | 2 | 2 | 2 |
| Supply Voltage Range | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V |
| Output Type | Buffered rail-to-rail voltage output | Buffered rail-to-rail voltage output | Buffered rail-to-rail voltage output | Buffered voltage output | Buffered voltage output | Buffered voltage output | Buffered voltage output |
| Serial Interface | 3-wire SPI, QSPI, MICROWIRE, and DSP compatible | 3-wire serial interface | 3-wire serial interface | 3-wire serial interface | 3-wire serial interface | 3-wire serial interface | 3-wire serial interface |
| Maximum Serial Clock Rate | 30 MHz | 30 MHz | 30 MHz | 30 MHz | 30 MHz | 30 MHz | 30 MHz |
| Reference Architecture | One reference pin per DAC channel | One reference pin per DAC channel | One reference pin per DAC channel | One reference pin per DAC channel | One reference pin per DAC channel | One reference pin per DAC channel | One reference pin per DAC channel |
主要差異化特點
- Lower output resolution than the higher-resolution family alternatives (對比AD5323ARUZ)
- Dual buffered outputs without external output amplifiers (對比AD5313ARUZ)
- Directly compatible with SPI-style host interfaces (對比AD5303BRU)
設計說明
Treat both reference pins as sensitive analog nodes. Route each reference directly to its assigned pin, keep the traces short, and avoid routing them beneath digital clock or serial-data lines. If a reference source sits far from the converter, place the required bypass capacitor at the device rather than at the source. This prevents supply and reference transients from appearing simultaneously on both analog outputs.
Use a compact analog and digital floor-plan with the converter near the interface controller, while keeping analog outputs and reference routing away from switching nodes. The TSSOP package allows the analog pins to be grouped, but pin assignments must be taken from the manufacturer pin-description table. Provide a quiet return path and avoid connecting output return current through the reference ground region.
Do not assume that identical package dimensions guarantee identical behavior when moving from the 8-bit AD5303 to a 10-bit AD5313 or 12-bit AD5323. Confirm serial-register behavior, code scaling, output settling, and reference requirements after substitution. Similarly, confirm the ordering grade and temperature range of AD5303BRU before using it as a production replacement for AD5303ARU.
The 230 uA specification applies to the converter at a 3 V supply. Total analog-channel power depends on the reference source, load current, and whether either output is disabled or updated continuously. Decouple the single supply close to the device and verify startup behavior at the minimum 2.5 V operating voltage, especially when the output load pulls downward during code transitions.
合規資訊
The manufacturer product page confirms RoHS-relevant product information availability, but no explicit compliance statement was extracted. The component is an analog data converter rather than an automotive-qualified device.