ISL8483IPZ - 5V RS-485/RS-422 Transceiver | Renesas
MPN: ISL8483IPZ ✗ 停產ISL8483IPZ 概覽
An RS-485/RS-422 transceiver is an interface IC that converts between single-ended logic signals and balanced differential signals. This signal format rejects common-mode noise and supports reliable communication over longer cables or across systems with different ground potentials. Within the broader semiconductor hierarchy, the ISL8483IPZ is a line-driver and line-receiver device, an interface IC, and a communications peripheral used between digital controllers and balanced-wired networks.
Key features include operation from a single 5 V supply, one driver and one receiver, support for both RS-485 and RS-422 applications, and slew-rate-limited outputs. Slew-rate limiting is particularly valuable in multidrop and multipoint networks because it lowers the high-frequency content of the driver edge. This helps control EMI and reduces reflections caused by unterminated transmission lines or stubs. The package also provides a straightforward through-hole footprint for legacy and industrial equipment.
The transceiver architecture supports point-to-point RS-422 links as well as multidrop RS-485 networks. The receiver provides the balanced input path, while the driver converts outgoing logic levels into differential line signals. Biasing, termination, common-mode range, driver loading, and maximum cable length remain system-level design considerations. Because those operating limits are not stated in the available product information, consult the manufacturer datasheet before finalizing network geometry or cable assumptions.
Typical uses include industrial instrumentation, factory automation equipment, building controls, industrial sensor gateways, remote monitoring links, and embedded serial buses. The same transceiver can be used in designs where interoperability between RS-422 and RS-485 equipment matters, provided the system configuration and termination strategy match the selected standard. Its through-hole package also makes it useful for repairs and expansions of boards designed around DIP-style interface devices.
When laying out the circuit, keep the balanced traces short, route the driver and receiver differential pair together, and avoid placing unrelated switching nodes between the two conductors. Apply termination only where it belongs in the network topology, normally at the physical ends of the cable. Confirm logic polarity, receiver enable behavior, grounding strategy, and bus loading against the manufacturer application guidance before applying power.
This product page combines the exact package and interface classification with application guidance, engineering design notes, and a compatibility-focused comparison. These practical details help engineers evaluate the ISL8483IPZ for industrial communications while separating confirmed device characteristics from parameters that must be confirmed in the manufacturer datasheet.
直接替換替代品,適用於 ISL8483IPZ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: ISL8483IPZ (相同外形與佔位) — 差異在於 Mounting Type, Operating Temperature Range, Package, Product Type, Receiver Count.
ISL8483CPZ
✅ 直接替換聯絡詢價
查看資料表 →ISL8483EIPZ
✅ 直接替換📋 參考替代品(不在目錄中)
ISL8483IPZ 規格
| Product Type | RS-485/RS-422 single transceiver |
| Transmitter Count | 1 transmitter |
| Receiver Count | 1 receiver |
| 供應電壓 | 5 V |
| Interface Standards | RS-422 and RS-485 |
| Technology | BiCMOS |
| 工作溫度範圍 | 0 °C to 70 °C |
| 封裝 | 8-pin PDIP |
| 封裝 / 外殼 | MS-001BA |
| 腳位數 | 8 pins |
| 安裝類型 | Through-hole |
| Packaging Type | Tube |
| Driver Edge Control | Slew-rate limited |
| ESD Protection | ESD protected |
| RoHS 狀態 | Compliant |
ISL8483IPZ ms-001ba 腳位配置指南
ISL8483IPZ(ms-001ba 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: ISL8483IPZ.
請參閱 資料表 以查看完整腳位配置。
典型應用
ISL8483IPZ 適用於 6 應用s: Industrial Sensor Gateway, Factory Automation Controller, Building Control Network, Remote Monitoring Link, Process Instrumentation Interface, Legacy Communications Board Repair.
Industrial Sensor Gateway
The ISL8483IPZ suits an industrial sensor gateway that must collect readings from a remote RS-485 bus and forward them to a local controller. Its single transmitter and single receiver provide one balanced communications direction, while the 5 V supply matches common embedded control platforms. The slew-rate-limited driver reduces electromagnetic interference and line reflections in multidrop installations. Use the receiver and driver terminals for the isolated field-bus pair, observe the specified 0 °C to 70 °C range, and verify the bus's node count, termination, and grounding against the manufacturer guidance.
推薦
Factory Automation Controller
The ISL8483IPZ can provide the balanced physical layer between a factory controller and remote actuators, motor-control electronics, or operator panels. Its 5 V operation and one-driver, one-receiver arrangement align with conventional embedded control systems, while slew-rate limiting helps contain high-frequency emissions on factory wiring. The 8-pin PDIP footprint is useful when maintaining an established through-hole control board. During layout, route the two conductors as a pair, apply the appropriate endpoint termination, and confirm that grounding and common-mode conditions remain compatible with the connected equipment.
推薦
Building Control Network
The ISL8483IPZ is applicable to building-control nodes that exchange commands and status over a balanced RS-485 wiring network. A single transceiver supports one communication link per device, and the controlled output slew rate helps reduce EMI where cables run near lighting, access-control, and HVAC equipment. Its 5 V supply is suitable for low-voltage control electronics, while the through-hole package simplifies compatibility with legacy building-control boards. Validate the complete network topology, termination locations, logic polarity, and operating temperature before field deployment.
推薦
Remote Monitoring Link
The ISL8483IPZ can connect a remote environmental or equipment-monitoring unit to a central collector over an RS-422 or RS-485 link. Balanced signaling improves noise immunity on cables that may run near motors, switching equipment, or other industrial sources. The device's one transmitter and one receiver are sufficient for a full-duplex RS-422 point-to-point connection or one multidrop RS-485 node. Designers should use twisted pair, maintain a controlled reference ground, and verify cable length and loading against the complete interface specifications before installation.
推薦
Process Instrumentation Interface
The ISL8483IPZ is appropriate for process-instrumentation equipment that must exchange measurements with a host controller over a balanced line. Its differential driver and receiver provide the physical interface, while slew-rate-limited transitions reduce the likelihood of excessive EMI or reflections in installed cabling. The 5 V supply supports integration with low-voltage instrumentation electronics, and the PDIP package can assist maintenance of older measurement platforms. Confirm receiver thresholds, common-mode behavior, bus loading, and isolation requirements before connecting field sensors or powered transmitters.
推薦
Legacy Communications Board Repair
The ISL8483IPZ is well suited to repairing or extending an established board that uses an 8-pin PDIP RS-485/RS-422 transceiver. Its through-hole mounting preserves the original mechanical footprint and avoids the need to redesign the board around a smaller surface-mount package. The 5 V interface supports many legacy embedded systems, and the one-transceiver arrangement covers a conventional point-to-point or network-node role. Before installation, compare every numbered pin with the original device and verify that replacement part temperature, ESD requirements, and control functions satisfy the original design intent.
推薦
推薦產品摘要
工程參考資料,適用於 ISL8483IPZ — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | ISL8483CPZ | ISL8483EIPZ |
|---|---|---|---|
| Package | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP |
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Product Type | Single RS-485/RS-422 transceiver | Single RS-485/RS-422 transceiver | Single RS-485/RS-422 transceiver |
| Supply Voltage | 5 V | 5 V | 5 V |
| Transmitter Count | 1 | 1 | 1 |
| Receiver Count | 1 | 1 | 1 |
| Interface Standards | RS-422 and RS-485 | RS-422 and RS-485 | RS-422 and RS-485 |
主要差異化特點
- Preserves the 8-pin PDIP footprint (對比ISL8483IBZ)
- Explicitly documented ESD-protected family option (對比ISL8483IPZ)
- Slew-rate-limited operation for balanced industrial links (對比ISL8483CPZ)
設計說明
Route the driver and receiver conductors as a tight differential pair on the PCB. Keep the pair away from switching nodes, relay coils, clock edges, and other high-energy traces. Use a continuous ground reference beneath the interface area where the system grounding strategy permits, and match the physical cable pair to the balanced line. Proper pair routing reduces radiated emissions and improves noise immunity.
Do not apply termination indiscriminately to every node in a multidrop network. RS-485 commonly uses termination at the two physical ends, while RS-422 point-to-point links require a different termination strategy. Also verify receiver enable polarity and bus-driver enable behavior against the manufacturer pin table before connecting two nodes that can drive the same pair simultaneously.
The slew-rate-limited driver is intended to reduce EMI and reflections, but it cannot compensate for poor cabling or topology. Use twisted-pair wiring, avoid long unterminated stubs, and keep branch lengths short. If the installation uses highly inductive loads or long cables, check grounding, common-mode range, protection devices, and data-rate limits in the complete interface design.
合規資訊
RoHS compliance is stated in the product information. REACH, halogen-free status, lead-free status, and conflict-minerals status are unknown.