XC6SLX16-L1CSG225I - 14579-Cell Spartan-6 LX FPGA | Xilinx
MPN: XC6SLX16-L1CSG225I ✓ 啟用中XC6SLX16-L1CSG225I 概覽
A field programmable gate array is a programmable logic semiconductor: an array of configurable logic blocks, block RAM, DSP slices and programmable I/O that is loaded at power-up with a bitstream defining the digital circuit. Within the market hierarchy, an FPGA sits above a fixed-function logic IC, above a CPLD, and inside the broader programmable-logic family. Spartan-6 LX devices occupy the cost-optimized, low-power segment of the Xilinx programmable logic portfolio, aimed at designs needing moderate logic density with high I/O count in a small package.
Key features of this device include a 667 MHz internal clock frequency, a -1L low-power speed grade, single-chip 45 nm CMOS construction, and 160 user I/O in only 225 balls of package area. The compact CSBGA-225 land pattern is a key differentiator over the FTG256 package used by many other Spartan-6 LX parts, saving roughly 30 percent of board area while keeping full-speed routing available. Industrial temperature operation supports factory, control, and instrumentation environments.
Technically, the device combines 14,579 logic cells with 589,824 bits of on-chip block RAM and a dedicated memory network, plus hard DSP multipliers for arithmetic pipelines. The 160 user I/O can be configured for LVCMOS 33, LVCMOS 18, LVCMOS 15, LVTTL and other standards, subject to bank-based voltage grouping. Because the part is a single monolithic die, there is no external configuration memory requirement beyond the standard serial or parallel bitstream loading interface.
Typical applications include industrial control and data acquisition front ends, compact video and image processing pipelines, low-power embedded networking and instrumentation, motor and motion control peripherals, and test and measurement front ends that need parallel data capture with low power consumption.
When designing around this device, remember that the CSG225 package demands tight ball-pitch escape routing, so plan power and ground planes and via-in-pad style escape strategy early. Confirm the -1L speed grade timing margin against your clock targets, and verify configuration pin states during power-up so the device enters the intended mode.
This page consolidates distributor availability, package-level drop-in alternatives, and practical design guidance that the factory datasheet alone does not present side by side, giving design engineers a faster path from part selection to a working board.
直接替換替代品,適用於 XC6SLX16-L1CSG225I — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: XC6SLX16-L1CSG225I (相同外形與佔位) — 差異在於 Device Type, Speed Grade, Mounting Type, Operating Temperature, Package.
XC6SLX16-2CSG225I
✅ 直接替換聯絡詢價
查看資料表 →XC6SLX16-2CSG225C
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →XC6SLX16-3CSG225C
✅ 直接替換聯絡詢價
查看資料表 →XC6SLX16-L1CSG225C
✅ 直接替換📋 參考替代品(不在目錄中)
XA6SLX16-3CSG225I
✅ 直接替換📋 參考替代品(不在目錄中)
XC6SLX16-L1CSG225I 最大額定值與電氣特性
| Device Type | Spartan-6 LX Field Programmable Gate Array (FPGA) |
| Logic Cells | 14579 cells |
| Block RAM | 589824 bits |
| User I/O | 160 I/O |
| Process Technology | 45 nm CMOS |
| Internal Clock Frequency | 667 MHz |
| Core Supply Voltage | 1 V |
| Speed Grade | -1L (low-power -1 speed grade) |
| 封裝 | 225-CSBGA (19 x 19 mm, 0.80 mm pitch) |
| Package Construction | Lead-free CSPBGA / LFBGA |
| 工作溫度 | 0 to 85 C (32 to 185 F) |
| 安裝類型 | Surface Mount |
| RoHS 狀態 | Lead-free package per manufacturer part data |
| Manufacturer Family | Spartan-6 LX |
| Data Sheet Reference | Spartan-6 FPGA Data Sheet: DC and Switching Characteristics (DS162) |
XC6SLX16-L1CSG225I lead-free cspbga / lfbga 腳位配置指南
XC6SLX16-L1CSG225I(lead-free cspbga / lfbga 封裝)的腳位配置。 此數位 IC 包含 GPIO、通訊介面(UART、SPI、I2C)與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料: XC6SLX16-L1CSG225I.
請參閱 資料表 以查看完整腳位配置。
典型應用
XC6SLX16-L1CSG225I 適用於 6 應用s: Industrial Control and Data Acquisition Front End, Compact Video and Image Processing Pipeline, Low-Power Embedded Networking Node, Test and Measurement Front End, Motion Control and Motor Drive Peripherals, Battery-Powered Sensor and IoT Hub.
Industrial Control and Data Acquisition Front End
The XC6SLX16-L1CSG225I fits machine control panels that must sample many sensors while keeping standby power low. With 160 user I/O in a 225-ball CSBGA, a single device can host encoder inputs, discrete sensor channels, valve drivers and an isolation barrier interface without adding a second logic device. The -1L speed grade is specified for low static and dynamic power, which matters when the controller spends most of its life in a duty-cycled sleep state between measurement bursts. The 589,824 bits of block RAM hold sample buffers, and the 45 nm CMOS implementation at a 1 V core supply keeps thermal rise manageable in a sealed enclosure.
推薦
Compact Video and Image Processing Pipeline
Video pipelines often need wide parallel capture and pixel manipulation rather than deep logic, which is exactly the profile of the XC6SLX16-L1CSG225I. The 160 user I/O can absorb a parallel RGB or YUV data bus from a video capture ASIC, while the 589,824 bits of block RAM provide line buffers and frame-rate pixel registers. The 225-CSBGA land pattern at 19 x 19 mm is significantly smaller than the 256-ball FTG256 alternative, which matters in camera modules and compact display boards. The -1L speed grade also limits switching power in battery or thermally constrained camera housings where radiated noise from fast switching is undesirable.
推薦
Low-Power Embedded Networking Node
Sensor nodes and industrial gateways that terminate one or more Ethernet or serial links are a natural fit for the XC6SLX16-L1CSG225I. The 160 I/O allow parallel PHY interfaces, MDIO management lines and UART or SPI channels to be serviced by one device, while 589,824 bits of block RAM hold packet buffers and protocol state. The low-power -1L grade is the key reason this part is preferred over faster variants in battery-backed telemetry nodes, because static and dynamic power scale directly with the speed grade selected. The 1 V core supply and 45 nm CMOS process simplify power tree design across a 3.3 V industrial input rail.
推薦
Test and Measurement Front End
Instrumentation front ends that must acquire wide parallel data and apply correction in real time benefit from the XC6SLX16-L1CSG225I combination of I/O count and fabric density. The 160 user I/O can be grouped into banks to accept TTL, LVCMOS and other logic levels directly from a DUT without level translation, and the block RAM acts as a deep capture FIFO between the acquisition logic and the serial link to the host. The -1L speed grade is appropriate for slow control-path and gating logic that sits alongside analog front ends, because the slower grade emits less switching noise that could couple into sensitive measurement paths through shared board ground planes.
推薦
Motion Control and Motor Drive Peripherals
The XC6SLX16-L1CSG225I can host the control law, encoder decoding and step/direction generation for a multi-axis motion controller while remaining a companion to a dedicated gate driver. The 160 user I/O cover quadrature encoder channels, limit inputs and pulse outputs without an external CPLD, and the 14,579 logic cells give headroom for proportional-integral-derivative loops and trajectory interpolation. Choosing the low-power -1L grade in equipment that runs continuously at moderate duty keeps thermal footprint low in sealed drive electronics. Note that the device does not replace the power stage itself; it complements it by providing deterministic timing and safety interlocks.
推薦
Battery-Powered Sensor and IoT Hub
Wearable and IoT hub designs that must aggregate several sensor streams while remaining on a small battery are well served by the XC6SLX16-L1CSG225I. The low-power -1L speed grade directly reduces switching loss at the modest clock rates typical of sensor aggregation, and the 225-CSBGA footprint at 19 x 19 mm keeps the board area close to the size of the sensor itself. The 160 I/O let a single device fan out I2C, SPI and GPIO lines to many peripheral sensors, while 589,824 bits of block RAM serve as a rolling data cache between sensor reads and wireless transmissions. The 0 to 85 C operating range suits consumer and indoor industrial housings.
推薦
推薦產品摘要
工程參考資料,適用於 XC6SLX16-L1CSG225I — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | XC6SLX16-2CSG225I | XC6SLX16-2CSG225C | XC6SLX16-3CSG225C | XC6SLX16-L1CSG225C | XA6SLX16-3CSG225I |
|---|---|---|---|---|---|---|
| Package | 225-CSBGA (19 x 19 mm, 0.80 mm pitch) | 225-CSBGA - same | 225-CSBGA - same | 225-CSBGA - same | 225-CSBGA - same | 225-CSBGA - same |
| Brand | Xilinx | Xilinx | Xilinx | Xilinx | Xilinx | Xilinx |
| Logic Cells | 14579 cells | 14579 cells | 14579 cells | 14579 cells | 14579 cells | 14579 cells |
| Block RAM | 589824 bits | 589824 bits | 589824 bits | 589824 bits | 589824 bits | 589824 bits |
| User I/O | 160 I/O | 160 I/O | 160 I/O | 160 I/O | 160 I/O | 160 I/O |
| Speed Grade | -1L (low-power -1) | -2 | -2 | -3 (fastest) | -1L (same) | -3 automotive |
| Temperature Suffix | I (industrial marking) | I | C (commercial) | C (commercial) | C (commercial) | I (automotive program) |
| Process Technology | 45 nm CMOS | 45 nm CMOS | 45 nm CMOS | 45 nm CMOS | 45 nm CMOS | 45 nm CMOS |
| Core Supply Voltage | 1 V | 1 V | 1 V | 1 V | 1 V | 1 V |
主要差異化特點
- Smallest 225-ball Spartan-6 LX land pattern with full 160 I/O (對比XC6SLX16-2FTG256C)
- Low-power -1L speed grade for thermally constrained designs (對比XC6SLX16-3CSG225C)
- Drop-in speed-grade upgradation without PCB changes (對比XC6SLX16-2CSG225I)
- Industrial temperature marking on the base speed grade (對比XC6SLX16-2CSG225C)
設計說明
The 225-CSBGA land pattern uses a 0.80 mm ball pitch over a 19 x 19 mm body, which is tight enough that a two-layer board cannot realistically escape all 160 user I/O. Plan a 6 to 8 layer stack-up with a solid ground plane under the device, place decoupling capacitors on the same layer as the device where possible, and route high-speed nets on short inner layers to keep via counts low. Because Spartan-6 banks require clean reference planes, keep any plane split away from the device footprint itself.
The device runs from a 1 V core supply, so the power tree must generate that rail separately from the 3.3 V I/O supply and each must be decoupled close to its supply pins. Follow the decoupling guidance in the DS162 data sheet for the recommended capacitor values and placement, and remember that the -1L speed grade is chosen for low power, meaning the quiescent contribution of the device itself becomes a meaningful part of the budget. Estimated: at a 1 V core rail, a 200 mA design at 100 percent utilization dissipates roughly 0.2 W, which the 45 nm CSBGA can shed without a heatsink in still air.
Swapping between XC6SLX16 speed grades is a hardware-free change but never a configuration-free change. The bitstream timing model, the static and dynamic power figures and the derating curves all differ between -1L, -2 and -3, so re-run timing analysis and regenerate the bitstream for the exact suffix you fit. Another common mistake is assuming the 225-CSBGA parts are interchangeable with the FTG256 or CSG324 packages because the die is the same; the ball maps are different and require a board respin.
Spartan-6 uses a high-performance SelectIO structure, and bank voltage must match the external logic level of every pin in that bank. Plan bank boundaries in the constraint file before layout so that the ball assignment of each bank is fixed, then bring each bank its own quiet supply through the decoupling network rather than sharing a single rail with unrelated signals. For LVCMOS 33 outputs driving short PCB traces, drive strength and slew settings in the design tools will determine edge rate and the amount of crosstalk into adjacent high-impedance inputs such as the configuration pins.
Configuration pins are multifunction and their state during power-up determines whether the device enters serial, parallel or JTAG mode. Do not leave the configuration mode select pins floating, and make sure the pull-up or pull-down network on the INIT and DONE lines matches the intended boot mode, otherwise the device may enter configuration mode and fail to lock the design. Test points on CCLK, DATA and DONE are worth adding on production boards so a failed configuration can be diagnosed without rework.
合規資訊
The manufacturer part data lists this device in a lead-free CSPBGA/LFBGA package. RoHS, REACH, halogen-free and conflict-minerals declarations are not stated in the sources for this part, so they are recorded as unknown. The XA6SLX16 automotive counterpart is the option to evaluate when AEC-Q100 qualification is required.